Bedienungsanleitung

LED TMH-30
LED TMH-60
Moving-Head Spot
© Copyright
Nachdruck verboten!
Reproduction prohibited!
Inhaltsverzeichnis
Table of contents
INTRODUCTION ............................................................................................................................................. 20
SAFETY INSTRUCTIONS............................................................................................................................... 20
OPERATING DETERMINATIONS.................................................................................................................. 22
DESCRIPTION OF THE DEVICE ................................................................................................................... 23
Features ....................................................................................................................................................... 23
Overview ...................................................................................................................................................... 23
INSTALLATION .............................................................................................................................................. 24
Rigging ......................................................................................................................................................... 24
DMX-512 connection / connection between fixtures.................................................................................... 26
Connection with the mains ........................................................................................................................... 26
OPERATION.................................................................................................................................................... 27
Stand Alone operation.................................................................................................................................. 27
Master/Slave operation ................................................................................................................................ 27
Control Board ............................................................................................................................................... 27
DMX-controlled operation ............................................................................................................................ 29
Addressing ................................................................................................................................................... 29
DMX-protocol ............................................................................................................................................... 29
14 DMX channel mode................................................................................................................................. 29
11 DMX channel mode................................................................................................................................. 32
2 DMX channel mode................................................................................................................................... 34
CLEANING AND MAINTENANCE ................................................................................................................. 34
Replacing the fuse ....................................................................................................................................... 35
TECHNICAL SPECIFICATIONS..................................................................................................................... 35
Das neueste Update dieser Bedienungsanleitung finden Sie im Internet unter:
You can find the latest update of this user manual in the Internet under:
www.eurolite.de
2/35
3/35
4/35
6/35
7/35
INSTALLATION
Projektormontage
8/35
9/35
10/35
UP
DOWN
werden
im
ENTER
11/35
12/35
13/35
Steuerkanal 5 - Rotierendes Goborad
Decimal Hexad.
0 18
00 12
19 37
13 25
38 56
26 38
57 75
39 4B
76 94
4C 5E
95 113 5F 71
114 127 72 7F
128 191 80 BF
192 255
C0 FF
Steuerkanal 6 - Goborotation
Decimal Hexad.
09
00 09
10 115 0A 73
116 119 74 77
120 225 78 E1
226 255 E2 FF
Steuerkanal 7 - Statisches Goborad, Gobo Shake
Decimal Hexad.
06
00 06
7 13
07 0D
14 20
0E 14
21 27
15 1B
28 34
1C 22
35 41
23 29
42 48
2A 30
49 55
31 37
Percentage S/F
0% 2%
S Offen
3% 5%
S Gobo 1
5% 8%
S Gobo 2
8% 11%
S Gobo 3
11% 13%
S Gobo 4
14% 16%
S Gobo 5
16% 19%
S Gobo 6
19% 22%
S Gobo 7
14/35
56 62
63 69
70 76
77 83
84 90
91 97
98 104
105 111
112 118
119 127
128 191
22%
25%
27%
30%
33%
36%
38%
41%
44%
47%
50%
24%
27%
30%
33%
35%
38%
41%
44%
46%
50%
75%
192 255
C0 FF
75% 100%
S
F
F
F
F
F
F
F
F
S
F
Steuerkanal 8 - Fokus
Decimal Hexad.
0 255 00 FF
Steuerkanal 9 - Prisma
Decimal Hexad.
0 15
00 0F
16 50
10 32
51 255 33 FF
FB FF
15/35
Steuerkanal 4 - Rotierendes Goborad
Decimal Hexad.
0 18
00 12
19 37
13 25
38 56
26 38
57 75
39 4B
76 94
4C 5E
95 113 5F 71
114 127 72 7F
128 191 80 BF
192 255
C0 FF
Steuerkanal 5 - Goborotation
Decimal Hexad.
09
00 09
10 115 0A 73
116 119 74 77
120 225 78 E1
226 255 E2 FF
Steuerkanal 6 - Statisches Goborad, Gobo Shake
Decimal Hexad.
06
00 06
7 13
07 0D
14 20
0E 14
16/35
21 27
28 34
35 41
42 48
49 55
56 62
63 69
70 76
77 83
84 90
91 97
98 104
105 111
112 118
119 127
128 191
15 1B
1C 22
23 29
2A 30
31 37
38 3E
3F 45
46 4C
4D 53
54 5A
5B 61
62 68
69 6F
70 76
77 7F
80 BF
8%
11%
14%
16%
19%
22%
25%
27%
30%
33%
36%
38%
41%
44%
47%
50%
11%
13%
16%
19%
22%
24%
27%
30%
33%
35%
38%
41%
44%
46%
50%
75%
192 255
C0 FF
75% 100%
Steuerkanal 8 - Prisma
Decimal Hexad.
0 15
00 0F
16 50
10 32
51 255 33 FF
FB FF
17/35
18/35
TECHNISCHE DATEN
45° C
60° C
0,5 m
0,1 m
T 3,15 A, 250 V
19/35
USER MANUAL
LED TMH-30/LED TMH-60
Moving-Head Spot
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initially start-up.
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
INTRODUCTION
Thank you for having chosen a EUROLITE LED TMH-30/LED TMH-60. If you follow the instructions given in
this manual, we are sure that you will enjoy this device for a long period of time.
Unpack your LED TMH-30/LED TMH-60.
SAFETY INSTRUCTIONS
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.
20/35
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.
Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C
connection cable or on the casing, do not take the device into operation and immediately consult your local
dealer.
This device falls under protection-class I. The power plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or
power outlets can lead to the destruction of the device and to mortal electrical shock.
Always plug in the power plug last. The power plug must always be inserted without force. Make sure that
the plug is tightly connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal
electrical shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.
The cable insert or the female part in the device must never be strained. There must always be sufficient
cable to the device. Otherwise, the cable may be damaged which may lead to mortal damage.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.
If extension cords are used, make sure that the core diameter is sufficient for the required power
consumption of the device. All warnings concerning the power cords are also valid for possible extension
cords.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can
be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the
device must be disconnected via the mains.
If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be
cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More
severe dirt in and at the device should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately
be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced
insulation can cause mortal electrical shock.
There must never be any objects entering into the device. This is especially valid for metal parts. If any metal
parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and
disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries.
HEALTH HAZARD!
Never look directly into the light source, as sensitive persons may suffer an
epileptic shock (especially meant for epileptics)!
Keep away children and amateurs!
Never leave this device running unattended.
21/35
OPERATING DETERMINATIONS
This device is a LED moving-head lighting effect for creating decorative effects. This product is only allowed
to be operated with an alternating current of 230 V, 50 Hz and was designed for indoor use only.
This device is designed for professional use, e.g. on stages, in discotheques, theatres etc.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
fixture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. There should not be any cables lying around. Please make sure that the unit cannot be
touched or bumped. You endanger your own and the safety of others!
This device must never be operated or stockpiled in sourroundings where splash water, rain, moisture or fog
may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical
shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet
and is installed in a distance of 0.5 meters between smoke machine and device. The room must only be
saturated with an amount of smoke that the visibility will always be more than 10 meters.
The ambient temperature must always be between -5° C and +45° C. Keep away from direct insulation
(particularly in cars) and heaters.
The relative humidity must not exceed 50 % with an ambient temperature of 45° C.
This device must only be operated in an altitude between -20 and 2000 m over NN.
Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the
device during thunderstorms.
- - -m
determines the minimum distance from lighted objects. The minimum distance
The symbol
between light-output and the illuminated surface must be more than this value.
The device must only be installed on a non-flammable surface. In order to safeguard sufficient ventilation,
leave 50 cm of free space around the device.
The housing must never touch surrounding surfaces or objects.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the
fixture.
For overhead use (mounting height >100 cm), always fix the fixture with an appropriate safety-rope. Fix the
safety-rope at the correct fixation points only. The safety-rope must never be fixed at the transport handles!
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly
fastened.
The maximum ambient temperature Ta = 45° C must never be exceeded.
Operate the device only after having become familiarized with its functions. Do not permit operation by
persons not qualified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
Never remove the serial barcode from the device as this would make the guarantee void.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, crash etc.
22/35
DESCRIPTION OF THE DEVICE
Features
Versatile LED Head Spot
• Compact lightweight
• 14, 11 or 2 DMX channels selectable for numerous applications
• Equipped with a 30 W LED (LED TMH-30)
• Equipped with a 60 W LED (LED TMH-60)
• 7 brilliant, dichroic colors plus white
• Rainbow effect with adjustable speed in both directions
• Gobo-wheel 1 with 6 rotating gobos plus open
• With gobo-shake function
• Gobo-wheel 2 with 8 static metal gobos plus open
• 3-facet prism
• Preprogrammed scenes in Program Run for stand-alone operation
• Electronic dimmer
• Motorized focus
• Programmable color-change speed and strobe effect
• Sound-controlled via built-in microphone
• Fan-cooled
• Exact positioning via 16 bit PAN/TILT movement resolution
• PAN-angle switchable between 540°, 360° and 180° (in sound and auto mode)
• TILT-angle switchable between 270°, 180° and 90° (in sound and auto mode)
• DMX-controlled operation or stand-alone operation with Master/Slave function
• Control board with LC display and foil-keyboard for adjusting the DMX-starting address, PAN/TILT
Reverse, Program, Reset
• DMX control via every standard DMX controller
Overview
(1) Projector head
(2) Lens
(3) Housing screw
(4) Yoke
(5) Base
(6) Carrying handle
(7) Microphone
(8) DMX indicator
(9) Rubber foot
(10) Control Board
(11) Mode/Esc-button
(12) Up-button
(13) Down-button
(14) Enter-button
(15) Display
23/35
(16) Fuseholder
(17) Power supply
(18) DMX-In socket
(19) DMX-Out socket
(20) Ventilation grille
INSTALLATION
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight
for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down
if the main attachment fails.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the first time and after changes before taking into operation another
time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a
skilled person once a year.
Procedure:
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all
24/35
installation material and the projector. If you lack these qualifications, do not attempt the installation yourself,
but instead use a professional structural rigger. Improper installation can result in bodily injury and.or
damage to property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing systems have to be
used. The projector must never be fixed swinging freely in the room.
Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do NOT install the projector!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector's
weight.
DANGER OF FIRE!
When installing the device, make sure there is no highly-inflammable
material (decoration articles, etc.) within a distance of min. 0.5 m.
CAUTION!
Use 2 appropriate clamps to rig the fixture on the truss.
Make sure that the device is fixed properly! Ensure that
the structure (truss) to which you are attaching the fixtures is secure.
The Moving-Head can be placed directly on the stage floor or rigged in any orientation on a truss without
altering its operation characteristics (see the drawing).
The fixture’s base enables to be mounted in two ways.
For overhead use (mounting height >100 cm), always install an appropriate safety bond.
You must only use safety bonds and quick links complying with DIN 56927, shackles complying with DIN EN
1677-1 and BGV C1 carbines. The safety bonds, quick links, shackles and the carbines must be sufficiently
dimensioned and used correctly in accordance with the latest industrial safety regulations (e. g. BGV C1,
BGI 810-3).
Please note: for overhead rigging in public or industrial areas, a series of safety instructions have to be
followed that this manual can only give in part. The operator must therefore inform himself on the current
safety instructions and consider them.
The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety
precautions!
Pull the safety bond through the attachment eyelet and over the trussing system or a safe fixation spot.
Insert the end in the quick link and tighten the fixation screw.
The maximum drop distance must never exceed 20 cm.
A safety bond which already hold the strain of a crash or which is defective must not be used again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by an expert!
Screw one clamp each via a M10 screw and nut onto the Omega-holders.
Insert the screws of the first Omega-holder into the respective holes on the bottom of the device. Tighten the
screws fully. Install the second Omega-holder.
25/35
DMX-512 connection / connection between fixtures
The wires must not come into contact with each other, otherwise
the fixtures will not work at all, or will not work properly.
Please note, the starting address depends upon which controller is being used.
Only use a DMX-cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture
or one fixture with another.
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the controller directly
with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated. Plug the terminator with a 120 Ω resistor
between Signal (–) and Signal (+) in the DMX-output of the last fixture.
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.
The occupation of the connection-cables is as follows:
Cable
Pin
International
Brown
Live
L
Blue
Neutral N
Yellow/Green Earth
The earth has to be connected!
If the device will be directly connected with the local power supply network, a disconnection switch with a
minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
The device must only be connected with an electric installation carried out in compliance with the IECstandards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum
fault current of 30 mA.
Lighting effects must not be connected to dimming-packs.
26/35
OPERATION
After you connected the effect to the mains, the EUROLITE LED TMH-30/LED TMH-60 starts running.
During the Reset, the motors are trimmed and the device is ready for use afterwards.
Stand Alone operation
In the Stand Alone mode, the LED TMH-30/LED TMH-60 can be used without controller.
Disconnect the LED TMH-30/LED TMH-60 from the controller and call the internal program. Please refer to
the instructions under Control Board.
Master/Slave operation
The master/slave operation enables that several devices can be synchronized and controlled by one masterdevice.
On the rear panel of the device you can find an XLR-jack (DMX Out) and an XLR-plug (DMX In), which can
be used for connecting several devices.
Choose the device which is to control the effects. This device then works as master device and controls all
other slave devices, which are to be connected to the master device via a DMX cable. Connect the DMX
OUT jack with the DMX IN plug of the next device.
Set the desired Master-mode - „Automatic program mode“ or „Sound controlled mode“ - for the masterdevice. Set the DMX address 1 for all slave-devices.
Control Board
The Control Board offers several features: you can simply set the starting address, run the pre-programmed
program or make a reset.
The main menu is accessed by pressing the Mode/Esc-button.
Browse through the submenu by pressing Up or Down.
Press the Enter-button in order to select the desired menu.
You can change the selection by pressing Up or Down.
Confirm every selection by pressing the Enter-button.
You can leave every mode by pressing the Mode/Escbutton. The functions provided are described in the
following sections.
MODE/ESC
UP
DOWN
ENT ER
27/35
28/35
DMX-controlled operation
You can control the projectors individually via your DMX-controller.
The device has three different DMX channel modes.
Every DMX-channel has a different occupation with different features. The individual channels and their
features are listed under DMX-protocol.
Addressing
The Control Board allows you to assign the DMX starting address, which is defined as the first channel from
which the LED TMH-30/LED TMH-60 will respond to the controller.
If you set, for example, the address to channel 15, the device will use the channel 15 to 28 for control.
Please, be sure that you don’t have any overlapping channels in order to control each LED TMH-30/LED
TMH-60 correctly and independently from any other fixture on the DMX-chain.
If several LED TMH-30/LED TMH-60 are addressed similarly, they will work synchronically.
Press the Up/Down-buttons for setting the desired starting address. Now you can start operating the LED
TMH-30/LED TMH-60 via your lighting controller.
Note:
The modes of DMX512 data are shown via the DMX indicator.
After switching on, the device will automatically detect whether DMX 512 data is received or not. If the data
is received, the DMX indicator to the right of the display will be flashing. If there is no data received at the
DMX-input, the DMX indicator does not light up.
This situation can occur if:
- the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the device.
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are swap
in the input connector.
Note:
It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last device in the link in order to
ensure proper transmission on the DMX data link.
DMX-protocol
The device has three different DMX channel modes. The Control Board allows you to assign the DMX
channel mode.
14 DMX channel mode
Control-channel 1 - Horizontal movement (PAN)
Push slider up in order to move the head horizontally (PAN).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be stopped at any position you wish.
Control-channel 2 - Vertical movement (TILT)
Push slider up in order to move the head vertically (TILT).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be stopped at any position you wish.
29/35
Control-channel 3 - PAN/TILT-speed
Decimal Hexad.
0 255 00 FF
Percentage S/F
0% 100% F Decreasing speed
Feature
Control-channel 4 - Colour-wheel
Linear colour change following the movement of the slider.
In this way you can stop the colour-wheel in any position.
Decimal Hexad.
0 15
00 0F
16 31
10 1F
32 47
20 2F
48 63
30 3F
64 79
40 4F
80 95
50 5F
96 111 60 6F
112 127 70 7F
128 191 80 BF
192 255 C0 FF
Percentage S/F
Feature
0% 6%
S Open / white
6% 12%
S Blue
13% 18%
S Light green
19% 25%
S Rose
25% 31%
S Light yellow
31% 37%
S Dark blue
38% 44%
S Green
44% 50%
S Red
50% 75%
F Forwards rainbow effect with decreasing speed
75% 100% F Backwards rainbow effect with increasing speed
Control-channel 5 - Rotating gobo-wheel
Decimal Hexad.
0 18
00 12
19 37
13 25
38 56
26 38
57 75
39 4B
76 94
4C 5E
95 113 5F 71
114 127 72 7F
128 191 80 BF
192 255 C0 FF
Percentage S/F
Feature
0% 7%
S Open
7% 15%
S Gobo 1
15% 22%
S Gobo 2
22% 29%
S Gobo 3
30% 37%
S Gobo 4
37% 44%
S Gobo 5
45% 50%
S Gobo 6
50% 75%
F Forwards gobo-wheel rotation with decreasing speed
75% 100% F Backwards gobo-wheel rotation with increasing speed
Control-channel 6 - Gobo rotation
Decimal Hexad.
09
00 09
10 115 0A 73
116 119 74 77
120 225 78 E1
226 255 E2 FF
Percentage S/F
Feature
0% 4%
S No rotation
4% 45%
F Forwards gobo rotation with decreasing speed
45% 47%
S No rotation
47% 88%
F Backwards gobo rotation with increasing speed
89% 100% S Rocking Gobo
Control channel 7 - Static gobo-wheel, gobo shake
Decimal Hexad.
06
00 06
7 13
07 0D
14 20
0E 14
21 27
15 1B
28 34
1C 22
35 41
23 29
42 48
2A 30
49 55
31 37
56 62
38 3E
63 69
3F 45
Percentage S/F
Feature
0% 2%
S Open
3% 5%
S Gobo 1
5% 8%
S Gobo 2
8% 11%
S Gobo 3
11% 13%
S Gobo 4
14% 16%
S Gobo 5
16% 19%
S Gobo 6
19% 22%
S Gobo 7
22% 24%
S Gobo 8
25% 27%
F Gobo 8 shake with increasing speed
30/35
70 76
77 83
84 90
91 97
98 104
105 111
112 118
119 127
128 191
192 255
46 4C
4D 53
54 5A
5B 61
62 68
69 6F
70 76
77 7F
80 BF
C0 FF
27%
30%
33%
36%
38%
41%
44%
47%
50%
75%
30%
33%
35%
38%
41%
44%
46%
50%
75%
100%
F
F
F
F
F
F
F
S
F
F
Gobo 7 shake with increasing speed
Gobo 6 shake with increasing speed
Gobo 5 shake with increasing speed
Gobo 4 shake with increasing speed
Gobo 3 shake with increasing speed
Gobo 2 shake with increasing speed
Gobo 1 shake with increasing speed
Open
Cont. gobo-wheel forwards rotation with decreasing speed
Cont. gobo-wheel backwards rotation with increasing speed
Control-channel 8 - Focus
Decimal Hexad.
0 255 00 FF
Percentage S/F
Feature
0% 100% F Continuous adjustment from far to near
Control-channel 9 - Prism
Decimal Hexad.
0 15
00 0F
16 50
10 32
51 255 33 FF
Percentage S/F
Feature
0% 6%
S Open
6% 20%
S Prism (no rotation)
20% 100% F Prism rotation with increasing speed
Control-channel 10 - Switching the LEDs, Strobe
Decimal Hexad.
0 15
00 0F
16 200 10 C8
201 250 C9 FA
251 255 FB FF
Percentage S/F
Feature
0% 6%
S Neutral
6% 78%
F Strobe-effect with increasing speed
79% 98%
F Random strobe-effect with increasing speed
98% 100% S LEDs on
Control-channel 11 - Dimmer intensity
Decimal Hexad.
0 255 00 FF
Percentage S/F
Feature
0% 100% F Gradual adjustment of the dimmer intensity from 0 to 100 %
Control-channel 12 - Reset, internal programs
Decimal Hexad.
0 44
00 2C
45 64
2D 40
65 94
41 5E
95 134 5F 86
135 174 87 AE
175 214 AF D6
215 255 D7 FF
Percentage S/F
Feature
0% 17%
S Neutral
18% 25%
S Blackout during PAN/TILT movement
25% 37%
S Reset
37% 53%
S Internal program low speed
53% 68%
S Internal program medium speed
69% 84%
S Internal program high speed
84% 100% S Music control
Control-channel 13 - PAN-movement with 16 Bit-resolution
Control-channel 14 - TILT-movement with 16 Bit-resolution
31/35
11 DMX channel mode
Control-channel 1 - Horizontal movement (PAN)
Push slider up in order to move the head horizontally (PAN).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be stopped at any position you wish.
Control-channel 2 - Vertical movement (TILT)
Push slider up in order to move the head vertically (TILT).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be stopped at any position you wish.
Control-channel 3 - Colour-wheel
Linear colour change following the movement of the slider.
In this way you can stop the colour-wheel in any position.
Decimal Hexad.
0 15
00 0F
16 31
10 1F
32 47
20 2F
48 63
30 3F
64 79
40 4F
80 95
50 5F
96 111 60 6F
112 127 70 7F
128 191 80 BF
192 255 C0 FF
Percentage S/F
Feature
0% 6%
S Open / white
6% 12%
S Blue
13% 18%
S Light green
19% 25%
S Rose
25% 31%
S Light yellow
31% 37%
S Dark blue
38% 44%
S Green
44% 50%
S Red
50% 75%
F Forwards rainbow effect with decreasing speed
75% 100% F Backwards rainbow effect with increasing speed
Control-channel 4 - Rotating gobo-wheel
Decimal Hexad.
0 18
00 12
19 37
13 25
38 56
26 38
57 75
39 4B
76 94
4C 5E
95 113 5F 71
114 127 72 7F
128 191 80 BF
192 255 C0 FF
Percentage S/F
Feature
0% 7%
S Open
7% 15%
S Gobo 1
15% 22%
S Gobo 2
22% 29%
S Gobo 3
30% 37%
S Gobo 4
37% 44%
S Gobo 5
45% 50%
S Gobo 6
50% 75%
F Forwards gobo-wheel rotation with decreasing speed
75% 100% F Backwards gobo-wheel rotation with increasing speed
Control-channel 5 - Gobo rotation
Decimal Hexad.
09
00 09
10 115 0A 73
116 119 74 77
120 225 78 E1
226 255 E2 FF
Percentage S/F
Feature
0% 4%
S No rotation
4% 45%
F Forwards gobo rotation with decreasing speed
45% 47%
S No rotation
47% 88%
F Backwards gobo rotation with increasing speed
89% 100% S Rocking Gobo
Control channel 6 - Static gobo-wheel, gobo shake
Decimal Hexad.
06
00 06
7 13
07 0D
14 20
0E 14
21 27
15 1B
Percentage S/F
0% 2%
S Open
3% 5%
S Gobo 1
5% 8%
S Gobo 2
8% 11%
S Gobo 3
Feature
32/35
28 34
35 41
42 48
49 55
56 62
63 69
70 76
77 83
84 90
91 97
98 104
105 111
112 118
119 127
128 191
192 255
1C 22
23 29
2A 30
31 37
38 3E
3F 45
46 4C
4D 53
54 5A
5B 61
62 68
69 6F
70 76
77 7F
80 BF
C0 FF
11%
14%
16%
19%
22%
25%
27%
30%
33%
36%
38%
41%
44%
47%
50%
75%
13%
16%
19%
22%
24%
27%
30%
33%
35%
38%
41%
44%
46%
50%
75%
100%
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 8 shake with increasing speed
Gobo 7 shake with increasing speed
Gobo 6 shake with increasing speed
Gobo 5 shake with increasing speed
Gobo 4 shake with increasing speed
Gobo 3 shake with increasing speed
Gobo 2 shake with increasing speed
Gobo 1 shake with increasing speed
Open
Cont. gobo-wheel forwards rotation with decreasing speed
Cont. gobo-wheel backwards rotation with increasing speed
Control-channel 7 - Focus
Decimal Hexad.
0 255 00 FF
Percentage S/F
Feature
0% 100% F Continuous adjustment from far to near
Control-channel 8 - Prism
Decimal Hexad.
0 15
00 0F
16 50
10 32
51 255 33 FF
Percentage S/F
Feature
0% 6%
S Open
6% 20%
S Prism (no rotation)
20% 100% F Prism rotation with increasing speed
Control-channel 9 - Switching the LEDs, Strobe
Decimal Hexad.
0 15
00 0F
16 200 10 C8
201 250 C9 FA
251 255 FB FF
Percentage S/F
Feature
0% 6%
S Neutral
6% 78%
F Strobe-effect with increasing speed
79% 98%
F Random strobe-effect with increasing speed
98% 100% S LEDs on
Control-channel 10 - Dimmer intensity
Decimal Hexad.
0 255 00 FF
Percentage S/F
Feature
0% 100% F Gradual adjustment of the dimmer intensity from 0 to 100 %
Control-channel 11 - Reset, internal programs
Decimal Hexad.
0 44
00 2C
45 64
2D 40
65 94
41 5E
95 134 5F 86
135 174 87 AE
175 214 AF D6
215 255 D7 FF
Percentage S/F
Feature
0% 17%
S Neutral
18% 25%
S Blackout during PAN/TILT movement
25% 37%
S Reset
37% 53%
S Internal program low speed
53% 68%
S Internal program medium speed
69% 84%
S Internal program high speed
84% 100% S Music control
33/35
2 DMX channel mode
Control-channel 1 - Internal programs
Decimal Hexad.
0 15
00 0F
16 75
10 4B
76 135 4C 87
136 195 88 C3
196 255 C4 FF
Percentage S/F
Feature
0% 6%
S Blackout
6% 29%
S Internal program low speed
30% 53%
S Internal program medium speed
53% 76%
S Internal program high speed
77% 100% S Music control
Control-channel 2 - Strobe
Decimal Hexad.
09
00 09
10 255 0A FF
Percentage S/F
Feature
0% 4%
S Neutral
4% 100% F Strobe-effect with increasing speed
CLEANING AND MAINTENANCE
The operator has to make sure that safety-relating and machine-technical installations are inspected by an
expert after every four years in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are inspected by a
skilled person once a year.
The following points have to be considered during the inspection:
1) All screws used for installing the devices or parts of the device have to be tighly connected and must not
be corroded.
2) There must not be any deformations on housings, fixations and installation spots (ceiling, suspension,
trussing).
3) Mechanically moved parts like axles, eyes and others must not show any traces of wearing (e.g. material
abrading or damages) and must not rotate with unbalances.
4) The electric power supply cables must not show any damages, material fatigue (e.g. porous cables) or
sediments. Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
DANGER TO LIFE!
Disconnect from mains before starting maintenance operation!
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or
solvents!
The cooling-fan should be cleaned monthly.
The interior of the fixture should be cleaned at least annually using a vacuum-cleaner or an air-jet.
There are no serviceable parts inside the device. Maintenance and service operations are only to be carried
out by authorized dealers.
34/35
Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Open the fuseholder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuseholder.
Step 3: Install the new fuse in the fuseholder.
Step 4: Replace the fuseholder in the housing.
Should you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply
cable available at your dealer.
Should you have further questions, please contact your dealer.
TECHNICAL SPECIFICATIONS
Power supply:
Power consumption:
DMX control channels:
DMX512 connection:
Sound-control:
Color-wheel:
Rotating gobo-wheel:
Static gobo-wheel:
Number of LEDs:
LED type:
Beam angle:
Ventilation fan:
Maximum PAN-movement:
Maximum TILT-movement:
Dimensions (LxWxH):
Weight:
LED TMH-30
Moving-Head Spot
230 V AC, 50 Hz ~
80 W/160 VA
2/11/14
3-pin XLR
via built-in microphone
7 colors and open
6 gobos and open
8 gobos and open
1
30 W
14°
Yes
540°
270°
250 x 245 x 315 mm
7 kg
Maximum ambient temperature Ta:
Maximum housing temperature TC (steady state):
Min. distance from flammable surfaces:
Min. distance to lighted object:
Fuse:
LED TMH-60
Moving-Head Spot
230 V AC, 50 Hz ~
135 W/235 VA
2/11/14
3-pin XLR
via built-in microphone
7 colors and open
6 gobos and open
8 gobos and open
1
60 W
14°
Yes
540°
270°
250 x 245 x 315 mm
7.5 kg
45° C
60° C
0.5 m
0.1 m
T 3.15 A, 250 V
Please note: Every information is subject to change without prior notice. 09.03.2012 ©
35/35