EuroLite LED PST-9W RGB DMX Spot, LED PST-9W TCL DMX Spot User manual

LED PST-9W RGB
DMX Spot
© Copyright
Nachdruck verboten!
Reproduction prohibited!
MULTI-LANGUAGE-INSTRUCTIONS
Inhaltsverzeichnis
Table of contents
Diese Bedienungsanleitung gilt für die Artikelnummer / This user manual is valid for the article number:
51916200
Das neueste Update dieser Bedienungsanleitung finden Sie im Internet unter:
You can find the latest update of this user manual in the Internet under:
www.eurolite.de
2/18
4/18
5/18
1
51916210
1
51916211
International
L
N
7/18
Dip Dip Dip Dip Dip Dip Dip Dip Dip Dip
1
2
3
4
5
6
7
8
9
10
Rot 100% an
1
0
0
0
0
0
0
X
0
0
1
1
0
0
0
0
0
X
0
0
Grün 100% an
0
1
0
0
0
0
0
X
0
0
Cyan 100% an
0
1
1
0
0
0
0
X
0
0
Blau 100% an
0
0
1
0
0
0
0
X
0
0
Magenta 100% an
1
0
1
0
0
0
0
X
0
0
1
1
1
0
0
0
0
X
0
0
X
X
X
1
0
0
0
X
0
0
X
X
X
0
1
0
0
X
0
0
X
X
X
0
0
1
0
X
0
0
X
X
X
0
0
0
1
X
0
0
Strobe (10 Hz)
X
X
X
X
X
X
X
1
0
0
Slave
1
X
X
X
X
X
X
X
X
1
DMX
X
X
X
X
X
X
X
X
X
1
8/18
1
2
3
4
5
6
7
1
2
4
8
16
32
64 128 256
8
9
On
Off
On
Off
Gerät 3 - Kanäle 11-15
On
Off
On
Gerät 4 - Kanäle 16-20
Off
On
Off
DMX-PROTOKOLL
Kanal:
1
Kanal:
2
Kanal:
3
Kanal:
4
Kanal:
5
9/18
10/18
USER MANUAL
LED PST-9W RGB DMX Spot
CAUTION!
Keep this device away from rain and moisture!
Never open the housing!
For your own safety, please read this user manual carefully before you initially start-up.
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
INTRODUCTION
Thank you for having chosen a EUROLITE LED PST-9W RGB DMX Spot. If you follow the instructions given
in this manual, we are sure that you will enjoy this device for a long period of time.
Unpack your LED PST-9W RGB DMX Spot.
SAFETY INSTRUCTIONS
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.
11/18
Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C
connection cable or on the casing, do not take the device into operation and immediately consult your local
dealer.
This device falls under protection-class I. The power plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or
power outlets can lead to the destruction of the device and to mortal electrical shock.
Always plug in the power plug last. The power plug must always be inserted without force. Make sure that
the plug is tightly connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal
electrical shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.
The cable insert or the female part in the device must never be strained. There must always be sufficient
cable to the device. Otherwise, the cable may be damaged which may lead to mortal damage.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.
If extension cords are used, make sure that the core diameter is sufficient for the required power
consumption of the device. All warnings concerning the power cords are also valid for possible extension
cords.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can
be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the
device must be disconnected via the mains.
If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be
cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More
severe dirt in and at the device should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately
be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced
insulation can cause mortal electrical shock.
There must never be any objects entering into the device. This is especially valid for metal parts. If any metal
parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and
disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries.
HEALTH HAZARD!
Never look directly into the light source, as sensitive persons may suffer an
epileptic shock (especially meant for epileptics)!
Keep away children and amateurs!
Never leave this device running unattended.
OPERATING DETERMINATIONS
This device is a lighting effect for creating decorative effects. This product is allowed to be operated with an
alternating voltage of 100 - 240 V, 50/60 Hz~ and was designed for indoor use only.
12/18
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
Never put any liquids close to the device. Should any liquid enter the device nevertheless, disconnect from
mains immediately. Please let the device be checked by a qualified service technician before you operate it
again. Any damages caused by liquids having entered the device are not subject to warranty!
Do not shake the device. Avoid brute force when operating the device.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. There should not be any cables lying around. You endanger your own and the safety of
others!
This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or fog
may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical
shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet
and is installed in a distance of 0.5 meters between smoke machine and device. The room must only be
saturated with an amount of smoke that the visibility will always be more than 10 meters.
The ambient temperature must always be between -5° C and +45° C. Keep away from direct insulation
(particularly in cars) and heaters.
The relative humidity must not exceed 50 % with an ambient temperature of 45° C.
This device must only be operated in an altitude between -20 and 2000 m over NN.
Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the
device during thunderstorms.
- - -m
The symbol
determines the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 0.1 meters.
The housing must never touch surrounding surfaces or objects.
The maximum ambient temperature Ta = 45° C must never be exceeded.
Operate the device only after having become familiarized with its functions. Do not permit operation by
persons not qualified for operating the device. Most damages are the result of unprofessional operation!
Never use solvents or aggressive detergents in order to clean the device! Rather use a soft and damp cloth.
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, etc.
INSTALLATION
Before attaching the device, make sure that the installation area can hold a minimum point load of 10 times
the device's weight.
The device must only be installed absolutely planar at a vibration-free, oscillation-free and fire-resistant
location. Make sure that the device is installed absolutely planar by using a water-level.
Please note: The device must be installed out of the reach of people.
13/18
The device must always be installed via all fixation holes. Do only use appropriate screws and make sure
that the screws are properly connected with the ground.
The durability of the installation depends very much on the material used at the installation area (building
material) such as wood, concrete, gas concrete, brick etc. This is why the fixing material must be chosen to
suit the wall material. Always ask a specialist for the correct plug/screw combination indicating the maximum
load and the building material.
Procedure:
Step 1: The hole for the installation is on the mounting bracket.
Step 2: Hold the mounting bracket onto the location where the device is to be installed.
Step 3: Mark the borehole with a pen or a suitable tool.
Step 4: Drill the hole.
Step 5: Hold the mounting bracket in the desired position and fix it.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by an expert!
DMX-512 control
The wires must not come into contact with each other, otherwise
the devices will not work at all, or will not work properly.
Please note, the starting address depends upon which controller is being used.
Only use a DMX-cable and the special connection cable having
stereo jack plugs included in delivery (see picture at right).
Additional adapter cables for further connections (not included
in delivery):
1
1
DMX-Adapter OUT LED PST-9W RGB 1m -- 3.5 mm stereo jack to 3-pin XLR
DMX-Adapter IN LED PST-9W RGB 1m -- 3-pin XLR to 3.5 mm stereo jack
51916210
51916211
Occupation of the XLR connection when using stereo jacks:
3 - Signal (+)
2 - Signal (-)
1 - Ground
3: Signal (+) - Tip
2: Signal (-) - Middle ring
1: Ground - Rear ring
14/18
If you are using controllers with this occupation, you can connect the DMX output of the controller directly
with the DMX input of the first device in the DMX chain. If you wish to connect DMX controllers with other
XLR outputs, you need to use adapter cables.
Building a serial DMX chain:
Connect the DMX output of the first device in the DMX chain with the DMX input of the next device. Always
connect one output with the input of the next device until all devices are connected.
Caution: At the last fixture, the DMX-cable has to be terminated. Plug the terminator with a 120 Ω resistor
between Signal (–) and Signal (+) in the DMX-output of the last fixture.
Connection with the mains
Connect the device to the mains with the power-plug.
The occupation of the connection-cables is as follows:
Cable
Brown
Blue
Yellow/Green
Pin
Live
Neutral
Earth
International
L
N
The earth has to be connected!
If the device will be directly connected with the local power supply network, a disconnection switch with a
minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
The device must only be connected with an electric installation carried out in compliance with the IECstandards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum
fault current of 30 mA.
Lighting effects must not be connected to dimming-packs.
OPERATION
After connecting the Spot to the mains, the EUROLITE LED PST-9W RGB DMX starts running.
The device has two operating modes. It can be operated via DIP Switches or it can be run in DMX-controlled
mode.
15/18
DIP-SWITCH CONTROLLED OPERATION
Function:
Dip Dip Dip Dip
1
2
3
4
Dip Dip Dip
6
7
5
Dip Dip Dip
8
9
10
Red 100% on
1
0
0
0
0
0
0
X
0
0
Yellow 100% on
1
1
0
0
0
0
0
X
0
0
Green 100% on
0
1
0
0
0
0
0
X
0
0
Cyan 100% on
0
1
1
0
0
0
0
X
0
0
Blue 100% on
0
0
1
0
0
0
0
X
0
0
Magenta 100% on
1
0
1
0
0
0
0
X
0
0
White 100% on
1
1
1
0
0
0
0
X
0
0
Program 1:
random 3-color switch
X
X
X
1
0
0
0
X
0
0
Program 2:
random 3-color fade
X
X
X
0
1
0
0
X
0
0
Program 3:
random 7-color switch
X
X
X
0
0
1
0
X
0
0
Program 4:
random 7-color fade
X
X
X
0
0
0
1
X
0
0
Strobe (10 Hz)
X
X
X
X
X
X
X
1
0
0
Slave
1
X
X
X
X
X
X
X
X
1
DMX
X
X
X
X
X
X
X
X
X
1
1 = on
0 = off
X = changeable
3-fold color change sequence: red > green > blue
7-fold color change sequence: red > yellow > green > cyan > blue > magenta > white
In order to select the desired program and speed, set dipswitch 9 and 10 to OFF.
Programs can be selected via dipswitches 4 – 7.
Speed can be adjusted via dipswitches 1 – 3 (see below).
DIP-Switch 1, 2, 3 OFF, (desired program chosen via DIP-Switch 4,5,6 or 7), color change every second.
DIP-Switch 1 ON, desired program chosen, color change every 5 seconds.
DIP-Switch 2 ON, desired program chosen, color change every 10 seconds.
DIP-Switch 1 & 2 ON, desired program chosen, color change every 15 seconds.
DIP-Switch 3 ON, desired program chosen, color change every 20 seconds.
DIP-Switch 1 & 3 ON, desired program chosen, color change every 25 seconds.
DIP-Switch 2 & 3 ON, desired program chosen, color change every 30 seconds.
DIP-Switch 1, 2 & 3 ON, desired program chosen, color change every minute.
16/18
DMX-CONTROLLED OPERATION
You can control the spots individually via your DMX-controller. Every DMX-channel has a different
occupation with different features.
Set the dipswitch 10 to ON.
Addressing
Each device occupies 5 channels. To ensure that the control signals are properly directed to each device,
the device requires addressing. This is to be adjusted for every single device by changing the DIP-switches
as set out in the table below.
The starting address is defined as the first channel from which the device will respond to the controller.
Please make sure that you do not have any overlapping channels in order to control each device correctly
and independently from any other fixture on the DMX data link. If two, three or more devices are addressed
similarly, they will work similarly.
Occupation of the DIP-switches:
Controlling:
After having addressed all LED PST-9W RGB DMX, you may now start operating these via your lighting
controller.
DMX-protocol
Channel:
1
Value:
000 – 255
Function:
Red (0 – 100%)
Channel:
2
Value:
000 – 255
Function:
Green (0 – 100%)
Channel:
3
Value:
000 – 255
Function:
Blue (0 – 100%)
Channel:
4
Value:
000 – 255
Function:
Master Dimmer
Channel:
5
Value:
000 – 000
001 – 005
006 – 010
011 – 255
Function:
On
Off
On
Strobe (increasing)
17/18
CLEANING AND MAINTENANCE
DANGER TO LIFE!
Disconnect from mains before starting maintenance operation!
We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use
alcohol or solvents!
There are no serviceable parts inside the device. Maintenance and service operations are only to be carried
out by authorized dealers.
Should you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by authorized dealers only
in order to avoid hazards.
Should you have further questions, please contact your dealer.
TECHNICAL SPECIFICATIONS
Power supply:
Power consumption:
Number of DMX channels:
DMX-512 connection:
Maximum ambient temperature Ta:
Maximum housing temperature TB:
Min. distance from flammable surfaces:
Min. distance to lighted object:
Number of 9W Tri Color LEDs:
LED beam angle:
Dimensions (LxWxH):
Weight:
100-240 V AC, 50/60 Hz ~
26 W
5
3.5 mm stereo jack plug
45° C
50° C
0.5 m
0.1 m
1
6°
135 x 165 x 170 mm
0.5 kg
Accessories:
DMX-adapter IN jack 3,5/XLR 1m
DMX-adapter OUT jack 3,5/XLR 1m
EUROLITE TH-50 Theatre hook, silver
Saveking Safety bond 3x600 black
EUROLITE DMX LED Operator 1 controller
EUROLITE DMX LED Operator 4 controller
Article No.:
51916211
51916210
58000650
58010252
70064501
70064504
Please note: All information is subject to change without prior notice. 31.10.2013 ©
18/18