JB systems IROCK 7S-7B, iRock 7B, iROCK 7S Bruksanvisning

Operation Manual
Mode d'emploi
Gebruiksaanwijzing
Bedienungsanleitung
Manual de instrucciones
WWW.BEGLEC.COM
Copyright © 2007 by BEGLEC cva.
Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.
EN - DISPOSAL OF THE DEVICE
Dispose of the unit and used batteries in an environment friendly manner
according to your country regulations.
PT - COMO DESFAZER-SE DA UNIDADE
Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em
conformidade com as normas vigentes no seu país.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.
This symbol means: indoor use only.
®
Thank you for buying this JB Systems product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
 This device has been designed to produce decorative effect lighting and is used in light show systems.
iRock 7S:
 High quality design scanner based on a MSD250/2 discharge lamp
 Suited for Pro DJ, renting companies & discotheques
 Master/slave mode with built-in programs + micro
 DMX 7 channels (pan - tilt - colour - gobo - gobo rotation - shutter - dimmer)
 DMX can be remotely set by iLEAD controller
 High quality optical lenses
 7 rotating gobos (also glass gobos)
 9 dichroic colours + white
 0-100% dimmer, blackout and high speed variable strobe
 Easily controlled with iLEAD, SM1612 or any other DMX controller
 Ultra-smooth micro stepper motors
iRock 7B:
 Same characteristics as iRock 7S
 With cylindric barrel instead of the regular mirror
 This barrel turns in all directions, spinning multiple beams throughout the whole space
BEFORE USE
 Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
 Operating instructions
 Power cable
 Hanging bracket
 2 stand adapters
SAFETY INSTRUCTIONS:
CAUTION: To reduce the risk of electric shock, do not remove the top cover.
No user-serviceable parts inside. Refer servicing to qualified service
personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use
or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
CAUTION
1/58
This symbol means: Read instructions.
This symbol determines: the minimum distance from lighted objects. The minimum distance between
light-output and the illuminated surface must be more than 1 meters.
 To protect the environment, please try to recycle the packing material as much as possible.
 A new light effect sometimes causes some unwanted smoke and/or smell. This is normal and disappears
after some minutes.
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
 This unit is for indoor use only.
 Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
 Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
 Don’t cover any ventilation openings as this may result in overheating.
 Prevent use in dusty environments and clean the unit regularly.
 Keep the unit away from children.
 Inexperienced persons should not operate this device.
 Maximum save ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
 The units’ surface temperature may reach up to 85°C. Don’t touch the housing with bare hands during its
operation.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Allow the device about 10 minutes to cool down before replacing the bulb or start servicing.
 Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.
 The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
 Check that the available voltage is not higher than the one stated on the rear panel of the unit.
 The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
 Never let the power-cord come into contact with other cables!
 This fixture must be earthed to in order comply with safety regulations.
 Don’t connect the unit to any dimmer pack.
 Always use an appropriate and certified safety cable when installing the unit.
 In order to prevent electric shock, do not open the cover. Apart from the lamp and mains fuse there are no
user serviceable parts inside.
 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 The housing and the lenses must be replaced if they are visibly damaged.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
2/58
LAMP (RE)PLACEMENT
OPERATION MANUAL
In case of replacement of the lamp or
maintenance, do not open the fixture
within 10 minutes until the unit cools
down after switching off. Always
unplug the unit before servicing! Always use the
same type of spare parts (bulbs, fuses, etc.)
When replacing parts, please only genuine spare
parts.
 Switch off the unit and unplug the mains cable.
 Wait for about 10 minutes until the unit has been
cooled down.
 Unscrew the 2 screws that close the lamp
compartment on the back of the fixture. (number 1
on the picture )
 On the inside you will see the lamp socket. Tear the
lamp socket gently out of the lamp compartment.
 Unplug the old lamp. Hold the lamp socket while
unplugging the lamp.
 Hold the lamp socket while pressing the new lamp
gently in the socket.
Attention! Check the label on the backside of the
device or see the technical specifications in this
manual to know which lamp should be used.
Never install lamps with a higher wattage! Lamps
with higher wattage generate temperatures the
device was not designed for. If the device uses a
lamp transformer, it will burn due to current
overload.
 Don’t touch the bulb with bare hands! This
drastically shortens the lifespan of the lamp. If you
touched the lamp, clean it with a cloth and a little
denatured alcohol. Wipe the lamp off before
installing.
 Put the new lamp back inside the unit. Be sure that the wires don’t touch the lamp.
 Close the lamp compartment with the screws.
 Turn on the unit and point the beam to a white surface. Use the three adjustment screws indicated by
“lamp adjust”. Gently turn these three screws until you obtain maximum light output.
 Done!
 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don’t cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
HOW TO SET UP THE UNIT
CONTROL PANEL:
ATTENTION: Install the gobos only when the unit is switched off!
Never unscrew the screws of the rotating gobo as the ball bearing will be opened. Repairing
this is very difficult!
Switch off the main supply and unplug the unit.
Open the plastic top cover (4screws)
Locate the gobo wheel and remove the fixation ring
of the gobo you want to change with an appropriate
tool.
Remove the gobo and insert the new gobo.
Press the fixation-ring together and insert it in the
front of the gobo.
Done!
3/58
1. DISPLAY shows the various menus and the selected functions.
2. LEDS
DMX
On
DMX input present
MASTER On
Master mode
SLAVE
On
Slave mode
SOUND
Flashing
Sound activation
4/58
To select the programming functions
To go backward in the selected functions
To go forward in the selected functions
To confirm the selected functions
4. REMOTE CONTROL INPUT: Used to connect a optional CA-8 hand controller while the unit is used in
standalone or master/slave mode.
5. SENSITIVITY: Used to adjust the sensitivity of the micro when the unit is used in standalone or
master/slave mode.
6. MICROPHONE: used to trigger the internal programs to the rhythm of the music.
7. DMX INPUT/OUTPUT: used for DMX512 linking. Use good quality 3pin XLR M/F balanced cable to link
the units together.
MAIN MENU:
 To select any of the pre-set functions, press
the MENU button up to when the required
one is shown on the display.
 Select the function with the ENTER button.
The display will blink.
 Use DOWN and UP button to change the
mode.
 Once the required mode has been selected,
press the ENTER button to select. After 8
seconds the display will automatically return
to the main functions without any change.
To go back to the functions without any
change press the MENU button. The main
functions are shown on the right.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMXsignal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(yes blackout) or
(no blackout) mode.
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Color Mode
Normal: only full colors can be selected.
Split colors: you can select full colors and 2 colors that are next to each other on the color wheel.
 Press the MENU button unitl
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
(split color) mode.
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Pan Inversion
Normal: Panning movement is not inverted.
Pan inversion: Panning movement is inverted
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
(pan inversion) mode.
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
DMX512 Address Setting
Used to set the starting address in a DMX
setup.
 Press the MENU button until
is
shown on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP buttons to change the
DMX512 address.
 Once the correct address shows on the
display, press the ENTER button to save it.
(or automatically return to the main
functions without any change after 8 seconds)
To go back to the functions without any
change press the MENU button again.
Tilt Inversion (iROCK 7S) or
Barrel Rotation Inversion (iRock 7B)
Tilt movement is not inverted.
Barrel movement is not inverted
inversion:
tilt movement is inverted
Barrel movement is inverted
 Press the MENU button until
(
) is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(normal) or
(tilt/barrel rotation inversion) mode.
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Normal:
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
(2 light show) mode.
 Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
5/58
6/58
Self-Test
Used to activate the internal “self-test” program which shows all possibilities of the unit.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER button to start the internal self-test program.
 To go back to the functions press the MENU button.
Dimmer Inversion
Standard dimming: fader closed ( DMX value 000 )  full light output
fader open ( DMX value 255 )  blackout
Inverted dimming:
fader closed ( DMX value 000 )  blackout
fader open ( DMX value 255 )  full light output




Press the MENU button up to when the
is shown on the display.
Press the ENTER button so the display starts blinking.
Use DOWN and UP buttons to select the
(normal) or
(dimmer inversion) mode.
Once the mode has been selected, press the ENTER button to save it. ( or automatically return to the
main functions without any change after 8 seconds )
To go back to the functions without any change press the MENU button again.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display always on) or
(display off when not used).
 Once the mode has been selected, press the ENTER button to save it. The led display stops working after
about 40 seconds
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button untill
is blinking on the display. (normal display)
 Use the ENTER button to change to the mode
(display inversion), the option will be automatically
stored after 8 seconds. Or press the ENTER button again return to the mode
(normal display).
 To go back to the functions press the MENU button.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER button to show the number of working hours in the display.
 To go back to the functions press the MENU button.
Reset
Used to force a reset of the unit.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER to reset all channels to their standard position.
 To go back to the functions press the MENU button.
Please also check the chapter about the DMX-channel configuration of the unit to find out how you can force
a reset by DMX.
HOW TO CONNECT THE UNIT BY DMX
The DMX-protocol is a widely used high speed signal to control intelligent light equipment.
You need to “daisy chain” your DMX controller and all the connected light effects with a
good quality XLR M/F balanced cable. To prevent strange behavior of the light effects, due
to interferences, you must use a 90Ω to 120Ω terminator at the end of the chain. Never
use Y-splitter cables, this simply won’t work!
Focus Adjust
Used to help you adjusting the focus of the light beam and gobos.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER button and the unit will focus on center position
You are able to adjust the focus with the UP/DOWN buttons on the unit (the display shows the current focus
status).
 To go back to the functions press the MENU button.
Each light effect in the chain needs to have its proper starting address so it knows which commands from the
controller it has to decode.
 HOW TO SET THE THE RIGHT STARTING ADDRESS:
Refer to the previous chapter (DMX-512 address setting) to learn how to set the starting address on this unit.
The starting address of each unit is very important. Unfortunately it is impossible to tell you in this user
manual which starting addresses you have to set because this completely depends on the controller you will
use… So please refer to the user manual of your DMX-controller to find out which starting addresses you
must set.
7/58
8/58
HOW TO OPERATE THE UNIT
Every time you turn the unit on, it will show Ir7b/Ir7s on the display and move all the motors to their ‘home’
position and you may hear some noises for about 20 seconds. After that the unit will be ready to receive
DMX signal or run the built-in programs.
You can operate the unit in three ways:
o By master/slave built-in preprogram function
o By CA-8 easy controller
o By universal DMX controller
 BY MASTER/SLAVE BUILT-IN PREPROGRAM FUNCTION:
Select this function when you want an instant show. By linking the units in master/slave
connection, the first unit will control the other units to give an automatic, sound
activated, synchronized light show. Its DMX input will have nothing plugged into it, and
its master-LED will be constantly on and sound-LED will flash to the music.
Important! This function only works when the blackout mode in the menu of the
master is set to OFF, otherwise nothing will happen! Read more about this
option in the “Main Menu” paragraph.
 SLAVES have 2 working options: The other units are set to slave mode (slaveLED is constantly on). In order to create a great light show you can introduce
contrast movements (pan/tilt of slave is inverted)  In the menu of the slave units
you can go to option
and select:
o
 Normal slave: slave works in sync with the master.
o
 2 light show: slave works in opposite with the master.
 BY EASY CONTROLLER:
When used in Master/slave mode we strongly advice you to use the CA-8 “Easy controller” Just connect
this small controller to the 1/4” jack of the master unit, and you will be able to control the following
FUNCTIONS:
Stand by Blackout the unit
Strobe
1.Gobo/Color
sync. strobe
Function
Mode
9/58
2.Sync. strobe
3.Two-light
strobe
Sound 1
(LED off )
X/Y moving
show mode
selection
( Show 1 ~ Show
4)
Color/Gobo
selection
1. Hold on for
gobo change.
2. Press shortly
for color
change.
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
First set Master unit, then set Slave units’
position.
Sound 2
(LED normal
blinking)
Slow/Sound 3
(LED on)
Position/ Latch
(LED fast blinking)
10/58
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Input:
Fuse:
Sound Control:
DMX connections:
Lamp:
Size:
Weight:
AC 230V, 50Hz
10A/250V Fast blow (20mm glass)
Internal microphone
3pin XLR male / female
MSD 250/2
695 x 340 x 250 mm
15 kg
®
AVANT UTILISATION
11/58
12/58
iRock 7S-7B























13/58


iRock 7S-7B
14/58
iRock 7S-7B
PANNEAU DE CONTRÔLE:
INSTALLATION EN HAUTEUR
15/58
iRock 7S-7B
16/58
iRock 7S-7B
17/58
iRock 7S-7B
18/58
iRock 7S-7B
19/58
iRock 7S-7B
20/58
iRock 7S-7B
Fonction
Mode
21/58
iRock 7S-7B
L'appareil est totalement éteint.
Strobe
Sélection du mode
1.Gobo / Color
moving show X/Y
sync.
(Show 1 - Show 4)
strobe
2.Sync. strobe
3.Two-light strobe
Son 2
(la LED clignote
normalement)
22/58
iRock 7S-7B
NEDERLANDS
HANDLEIDING
MAINTENANCE
®
23/58
iRock 7S-7B
24/58
iRock 7S-7B
NEDERLANDS
HANDLEIDING
25/58
iRock 7S-7B
NEDERLANDS
HANDLEIDING
26/58
iRock 7S-7B
NEDERLANDS
HANDLEIDING
NEDERLANDS
HANDLEIDING
INSTELLEN VAN HET TOESTEL
Bedieningspaneel:
OPHANGEN VAN HET APPARAAT
27/58
iRock 7S-7B
28/58
iRock 7S-7B
NEDERLANDS
HANDLEIDING
HOOFDMENU:
29/58
HANDLEIDING
NEDERLANDS
iRock 7S-7B
30/58
iRock 7S-7B
NEDERLANDS
HANDLEIDING
NEDERLANDS
HANDLEIDING
31/58
iRock 7S-7B
32/58
iRock 7S-7B
NEDERLANDS
HANDLEIDING
 DMX-CONFIGURATE VAN DE IROCK 7S-7B:
NEDERLANDS
HANDLEIDING
Functie
Modus
33/58
iRock 7S-7B
Blackout het toestel
Strobo
X/Y bewegings
1.Gobo / kleur
show modus
sync. strobo
selectie
2.Sync. strobo
( Show 1 ~ Show 4 )
3.”Two-light”
strobo
geluid 1
geluid 2
(LED uit )
(LED knippert
normaal)
34/58
X/Y beweging instelling
1.Pan positie
2.Tilt positie
Stel eerst het Master toestel in,
stel daarna de de positie van de
Slave toestellen in.
Positie/ vergrendelen in een
positie
(LED knippert snel)
iRock 7S-7B
NEDERLANDS
HANDLEIDING
ONDERHOUD
TECHNISCHE KENMERKEN
Netvoeding:
Zekering:
Geluidscontrole:
DMX verbinding:
Lamp:
Afmetingen:
Gewicht:
®
35/58
iRock 7S-7B
36/58
iRock 7S-7B




37/58
iRock 7S-7B











38/58
iRock 7S-7B
ÜBERKOPF-MONTAGE
3. TASTEN
39/58
iRock 7S-7B
40/58
iRock 7S-7B
(iRock 7B)
Normal:
41/58
iRock 7S-7B
42/58
iRock 7S-7B
43/58
iRock 7S-7B
44/58
iRock 7S-7B
Modus
Blackout des Geräts
Strobe
X/Y bewegte Show
1.Gobo / Color
Modusauswahl
sync.
( Show 1 ~ Show 4
strobe
)
2.Sync. strobe
3.Two-light strobe
Sound 1
(LED off )
Stand-by
45/58
iRock 7S-7B
46/58
iRock 7S-7B
MANUAL DE INSTRUCCIONES
MANUAL DE INSTRUCCIONES
INSTRUCCIONES DE SEGURIDAD:
CAUTION
®

























47/58
48/58
MANUAL DE INSTRUCCIONES
49/58
MANUAL DE INSTRUCCIONES
MONTAJE SUPERIOR
50/58
MANUAL DE INSTRUCCIONES
CONFIGURACIÓN DE LA UNIDAD
MANUAL DE INSTRUCCIONES
MENÚ PRINCIPAL:
PANEL DE CONTROL:
51/58
52/58
MANUAL DE INSTRUCCIONES
53/58
MANUAL DE INSTRUCCIONES
54/58
MANUAL DE INSTRUCCIONES
CONEXIÓN DE LA UNIDAD MEDIANTE DMX
MANUAL DE INSTRUCCIONES
55/58
56/58
MANUAL DE INSTRUCCIONES
MANEJO DE LA UNIDAD
Modalidad
Sonido 1
(LED apagado )
Sonido 2
(LED
parpadeando
normalmente)
MANUAL DE INSTRUCCIONES
MANTENIMIENTO
Stand by
CA 230V, 50Hz
10A/250V rápido (20 mm cristal)
Micrófono interno
3 clavijas XLR macho / hembra
MSD 250/2
695 x 340 x 250 mm
15 kg
57/58
58/58">