Tomei Genesis Owner's manual

2015年1月 M60Y01-0
番
Part Number
適
合
Application
663006
HYUNDAI GENESIS COUPE
Please carefully read this manual prior to installation.
Please also refer to the HYUNDAI Service Manual with this Manual.
After the installation has been completed please keep this manual for future reference.
If the install was done in a shop please make sure to give this manual to the owner.
Thank you for purchasing another quality TOMEI product.
This TOMEI Carbon rear bumper cover has been designed to cover the empty gap on the bumper
when upgrading to the TOMEI single Titanium exhaust muffler. For street cars cosmetics this cover
has been made with Carbon for both looks and light weight benefits.
1
部品構成
2
KIT CONTENTS
REQUIRED TOOLS
Below is the contents of this kit with the quantity
listed in brackets ().
These tools are the bare minimum required
the job.
・ Double Sided Tape
Or
・Hand Drilled
・Riveted on
Carbon Rear Bumper Cover (1)
CAUTION
■
■
■
■
This product is designed to be used for off road competition purposes only.
This product is not to be used on public roads.
This product is to be installed by a qualified professional in a fully equipped workshop.
This product was designed specifically for the application specified. If the attempt was made to use this product
on another engine/car other than specified then you will risk damaging this kit and or the engine or components
related with it.
■ Do not use any excessive force when using this product as you risk damaging the product or other parts.
■ This product is to be installed with the appropriate tools and equipment to prevent any engine failures and
injuries or bodily harm.
WARNING
■ Install the product only when the exhaust is cold.
■ Please check that the product is installed properly and securely. Or there may be a risk of causing damage to
your car or other surrounding cars.
1. INSTALLATION
【INSTALLATION PROCEDURE】
1. Remove all signs of oil from the surface of the carbon
cover if you want to paint it to match the rest of your
bumper.
Designed for this side
2. Fit it with a strong double sided tape, or pop rivet it on
with 10 rivets.
(Recommended:φ4.8mm Rivets/Clamp thickness t=4.0mm)
Or you can use both methods to ensure that the part
does not come off.
2. INSTALLATION VERIFICATION
1. Check to verify that there is nothing loose after the installation.
2. Run the car at idle, then raise the RPM to 2500rpm to verify that there are no abnormal sounds.
3. Verify the test runs are all cleared and free from any loose fitments signs and sounds.
WARNING
■ Drive the car slowly and carefully in the beginning to be sure that nothing comes off or falls off at high speeds.
■ If anything abnormal about the car is noticed when driving, please stop the vehicle immediately to check where
the problem is from.
■ Make sure that the muffler is cold before making any changes, adjustments and/or checks.
■ If any part(s) has fallen off the car or come loose. Do not run the car. Stop the engine immediately and call the
shop who installed to the product to check your cars condition before any problems escalate.
CAUTION
■ Check everything to verify that there are no loose parts after the installation has been completed.
3
株式会社 東名パワード
〒194-0004 東京都町田市鶴間１７３７－３
TEL : ０４２－７９５－８４１１（代）
FAX : ０４２－７９９－７８５１
1737-3 Tsuruma Machida-shi Tokyo 194-0004 JAPAN
TEL : +81-42-795-8411(main switchboard)
FAX : +81-42-799-7851
http://www.tomei-p.co.jp
この製品に関わる取り付け、操作上のご相談は上記へお願いします。
営業時間：月～金（祝祭日、年末年始を除く）９：００～１８：００
If you have any questions in regards to the installation of this product,
please contact your local authorized Tomei Powered distributor.
OPEN: Monday - Friday (National holidays and public holidays excluded). 09:00 - 18:00
カーボンリヤバンパーカバー(HYUNDAI GENESIS COUPE用） 取扱説明書 2015年1月 M60Y01-0
4