Ilnstallat!on

Built-In Wall Oven
27" (68.6 cm) models
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938, ZEK958
Ilnstallat!on
nstruct=ons
30" (76.2 cm) models
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958
If you have questions, call 1.800.GE.CARES
ge.com
Before You Begin
Read these instructions carefully and completely.
• IMPORTANT-save
instructions
these
for local inspector's
• IMPORTANT-observe
use.
all
governing codes and ordinances.
• Note to Installer--Be
sure to leave these
instructions with the consumer.
or visit our website at:
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
• NOTE--This
grounded.
appliance
must be properly
• ATTENTION INSTALLER
• Note to Consumer--Keep
these
instructions for future reference.
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Parts Included
Materials Needed
(Appearance
will vary)
Wire Nuts
Screws For Installation
(8-18 x .750 flat head
Phillips wood screws)
27" (68.6 cm)
Metal Bottom Trim
Strain Relief Clamp
for 1/2" conduit
Junction
Box
36" (91 cm)
of String
Tools Needed
WB07T10578 - Black
WB07T10579 - SS
Optional 27" (68.6 cm)
Metal Bottom Trim Assembly
(on some models or can be
purchased separately)
31-10647-3
11-07 JR
30" (76.2 cm)
Metal Bottom Trim
Assembly
1/8" (3 mm) Drill Bit and
Electric or Hand Drill
Phillips
Screwdriver
Installation instructions
PORTANT SAFETY I ST
CTIONS
lectrical
For Your Safety
• Be sure your oven is installed properly by
a qualified installer or service technician.
Requirements
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
Rating plate is located on oven side trim,
side front frame or lower front frame.
Rating Plate
Location
• Make sure the cabinets and wall
coverings around the oven can withstand
the temperatures
(up to 200°F [93.3°C])
generated by the oven.
WARNING:
We recommend you have the electrical wiring
and hookup of your oven connected by a qualified
electrician. After installation, have the electrician
show you where your main oven disconnect is
located.
The electrical
power to the oven supply line
must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your oven
according to governing codes could result in a
hazardous condition. If there are no local codes,
your oven must be wired and fused to meet the
requirements of the National Electrical Code,
ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
lectrical
Requirements
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse. See the
rating plate located on the oven frame to determine
the rating of the product. Use the chart below to
determine the minimum recommended dedicated
circuit protection.
KW Rating
240V
KW Rating
208V
Recommended
Circuit Size
(Dedicated)
<4.8 KW
<4.1 KW
20 Amp
4.9 KW-7.2 KW
4.3 KW-6.2 KW
30 Amp
7.3 KW-9.6 KW
6.3 KW-8.3 KW
40 Amp
9.7 KW-12.0 KW
8.4 KW-10.4 KW
50 Amp
cont.
Effective January 1, 1996, the National
Electrical Code requires that new, but not existing,
construction utilize a four-conductor connection to
an electric oven. When installing an electric oven
in new construction, a mobile home, recreational
vehicle or an area where local codes prohibit
grounding through the neutral conductor,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR-CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for
use with aluminum wiring must be used.
2
Insta
ion instructions
Pre-lnstallation Chec
Door removal is not a requirement for
installation of the product, but is an
added convenience. To remove the door:
ALL INSTALLATION
INFORMATION
ON THE FOLLOWING PAGES IS TO
BF USED FOR SINGLE AND DOUBLE
OVEN INSTALLATION!
[_
Remove packaging materials.
Check behind hinges and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.
__
ist
Open the oven door as far as it will go.
Push both hinge
_
:,,_
Hinge
Unlocked
locks down toward
,_I_:'_L
Position
the door frame,
Hinge"I_
to the unlocked
s_ot _.d
position. This may
require a flat blade
Hinge
screwdriver.
Arm
=
[_
DO NOT LIFT THE DOOR
[_
Place hands on both sides of
the door, and close the oven
door to the removal position,
which is most of the way closed,
[_
ift door
up and
out
until the
hinge arms
clear the slots.
"_
11_
t_/
t _'/
Oven Racks
_
iterature
Pack
Open oven door and remove literature
pack and oven racks.
Hinge Clears Slot
NOTE: The oven door is very heavy. Be sure
you have a firm grip before lifting the oven
door off the hinges, Use caution once the
door is removed. Do not lay the door on its
handle. This could cause dents or scratches.
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Owner's
Manual, Installations, etc. in a safe place
for future reference.
Place the oven on a table or platform
even with the cutout opening. (Platform
must support 150 Ibs. [68 Kg] single,
275 Ibs. [124 Kg] double.)
Remove the bottom trim from the top
of the oven. It will be installed at the end
of the installation process. The trim is
wrapped separately and taped to
the top of the unit.
3
Installation instructions
uilt-ln
Cutout for 27" (68.6c )Single
Ovens on y
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Cabinet
5" (12.7 cm)
Max. from the
left or right
Cabinet_
_sk
I
27"
(68.6
cm)
Cutout
for overlap of
oven over side
edges of cutout
Width
tOcm)
0¥
runners
Box
,, : ,,
"!-'
level
adjacent
1" (2.5
cm)
ciearance°f
20" (50.8teCta),41
for _
a_jacen,
corners, drawers, wails,
etc. when door is open
overlap
of
oven top and
bottom
of cutout'_"'_--_
minimum
for
Cutout
Width
25" (63.5 cm) Min.
Recommended
cutout location
from Roor 32 1/2"
(82.6
Height
27 5/8" (70.2 cm) Min.
28 1/8" (71.4 cm) Max.
I
access
from
Box Location
Allow"
Allow a minimum
23 1/2"
(59.7 cm) Min.
Cutout
20" (50.8 era)
"
Depth
25 1/4" (64.1 cm) Max.
28 118"
with bottom
of cutout
32 1/2" (82.6 cm)
Cutout
/_
Cutout
Height
22" (55.9 cm)
27 5/8"
Min. above
(70.2 cm) Min. base rail
2" x 4"
(Scmx
Junction
Location
27" (68.8 cm)
Recommended
Cutout Location
from Floor
i
25" (63.5 cm)
Min.
j
25 114" (64.1
Max.
Allow 1" (2.8 era)
!_
/
Width
cabinet
may be required
NOTE: if the cabinet does not
have a front frame and the sides
are less than 3/4" (1.9 cm) thick,
shim both sides equally to
establish
the cutout width.
cm)
2" x 4" (5 cmx
tO cm) or
equivalent
runners love|
with bottom
of cutout
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
single ovens, the runners and braces
must support 150 Ibs (68 Kg).
T
24"
(61 cm)
NOTE: If marks, blemishes
or the
cutout opening are visible above the
installed oven, it may be necessary
to
add wood shims under the runners and
front trim until the marks or opening
are covered,
1
I-'_- 18" (45.7 cm) "-_1
"_
27" (68,6 cm) "_
These ovens are not approved
stackable installations.
4
for
Installation instructions
Cutoutfor 27"(68.6
Ovensonly
For JKP35, JKP55,
JKP75,
PK956, ZEK958
models
only.
5"
(12.7 cm)
Max. from
the left or
Cabinet
right
(68.6
cm) _
Cutout
i
__
Junction Box
oven
over
27" (68.6 cm)
Recommended
Cutout Location
from Floor
13 1/4" (33.7 cm)
Cutout Depth
23 5/8" (60 cm) Min.
Cutout Width
25" (63.5 cm) Min.
Location
5" (63.5 cm) Min.
25 1/4"
i
Allow 1" (2.5 cm)
for overlap of
Cabinet Width
(s4.1cm) M_,
side
25 114" (64.1 cm) Max.
edges of cutout
(111.8 cm)
Cutout Height
Min.
icut°ut
Above
iHeight
base rail
i49 11116"
i(126.2 cm) IVlin.
150 118"
i(127.3 cm) Max.
50 1/8" (127.3 cm) Max.
NOTE: If the cabinet does
not have a front frame and
the sides are less than 314"
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
20" (50.8
--_
j°s-
.... Ailo_v
I"
Allow a minimum
of 20" (50.8 cm)
for clearance to
adjacent corners,
drawers, walls, etc.
when door is open
(2,5 cm) for
overlap of oven
top and bottom_
49 11116" (126.2 cm) Min.
Recommended
cutout location
from floor 13 114"
(33.7 cm)
of cutout
if the cabinet does not have a solid bottom,
two braces or runners must be installed to
support the weight of the oven. For double
ovens, the runners and braces must
support 300 Ibs (135 Kg).
NOTE: If marks, blemishes
or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
--
Suitable
Bracing
to Support
Runners
Over Centerline
of Cabinet
5
2" x 4"
(ScmxtOcm)
or equiva|ent
ruuners
level
with bottom
of cutout
Installation instructions
Cutout for 27" (68.6c_)Single Built-in
Ovens only Under Counter
For JKS10, JKP30, JKPT0, PK916, ZEK938 models only.
Gas or electric cooktops may
be installed over this oven.
See cooktop installation
instructions for cutout size.
See label on top of oven for
approved cooktop models.
\
240V / 208V
Junction Box
Location
25" (63.5 cm)
5"
(12.7 cm)
Max. from the
left or right
side
Gas and electrical connections
for gas cooktop must be located
in an adjacent accessible
location to the right.
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
_25" (63.5 cm) Min.
25 1/4" (64.1cm) Max.
Allow
I"
(2.5 cm)
unit overlap top
bottom of
oven, 1" (2.5 cm)
unit overlap side
edges
27 5/8" (70.2 cm) Min.
28 1/8" (71.4 cm) Max.
_J
J
22" (55.9 cm) Min.
Above Support
Platform
_,
36" (91.4 cm)
Typical
Countertop
Height
4"(10.2 cm)
Typical
Toekick
MUST SUPPORT 150 LBS. (68 Kg)
i
6
be installed under the specific models
NOTE: This oven is only approved
to
I_t
I_t
JJJ
Cabinetry
for 27" (68.6
c_)Single or
uilt-ln Ovens only- Over a
Drawer
For JKS10, JKP30, JKP35, JKP55, JKPT0, JKP75, PK916, PK956, ZEK938,
ZEK958 models only.
Double 27" (68.6 cm)
Single 27" (68.6 cm)
Oven Over
Oven Over
a Warming Drawer
a Warming Drawer
Anti-Tip Block
Against Rear
• Wall Per
Warming
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
Drawer
Requirement
2" (5.1 cm)
Min.
2" (5.1 era)
Min,
NOTE: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
Per
Warming
Drawer
Requirement
J
Per Warming
Drawer
Req=
1" (2.5 cm) Min. Above Toekick
1" (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height.
When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
7
Cabinetry
Cutoutfor 27"(68.6
o_)SingleOvensonlyBelowan Advantiumor ;rowave Oven
or Betweenan Advantiumor crowave
Ovenand a WarmingDrawer
For JKS10, JKP30, JKP70, PK91& ZEK938 models only.
Single 27" (68.6 cm) Oven
Between an Advantium or
Microwave Oven and a
Warming Drawer
Single 27" (68.6 cm) Oven
Below an Advantium or
Microwave Oven
Per Advantium or
Microwave Oven
Requirement
Per Advautium or
Microwave Oven
Requirement
2" (5.1 cm) Min.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
2" (5.1 cm) Min.
2" (5.1 cm) Min.
Per Warming
Drawer
Req
NOTE: The middle rail separating the two
openings may need to be larger than the 3"
(7.6 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the 2"
(5.1 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
Combined Advantium or Microwave
Oven and Wall Oven Installation:
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
Refer to the Advantium or microwave
oven installation instructions for electrical
requirements of that product.
These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
Warming DrawerCombinedwith
Advantiumor MicrowaveOvenand
Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
instructions packed with each product
for specific requirements.
8
Installation instructions
Cutout for 30"(76.2c )Sing
Ovensonly
Built-in
For JTP30, JTP70, PT916, PT920, ZET938 models
only.
Cutout
Width
28 1/2" (72.4 cm)
9 1/2" (24.1 cm)
Junction Box
Location
(junction box
may be
located in
5/8"(72.7
ore)
Max.
I
Allow 11/16"
I
(1.75 cm) for
overlap of oven
over side edges
of cutout
21
Opening
Between
inside Walls
Must Be
At Least
28 1/2"
(72.4 cm)
Wide
/
(69.2 cm) Min,
27 5/16"
(69.4 cm) Ma
30" (76.2 cm)
Recommended
Cutout Location
from Floor
32 1/2" (82.6 cm)
Cutout Depth
23 1/2" (59.7 cm) Min.
Cutout Width
28 1/2" (72.4 cm) Min.
28 518" (72.7 cm) Max.
Cutout Height
22" (55.9 cm)
Min. to
Bottom of
Junction Box
27 1/4" (69.2 cm) Min.
27 5/16" (69.4 cm) Max.
---4
-
Ill not have a front frame and the
t_1sides are less than 314" (1.9 cm)
_AIl_w 1" (2.5 cm)
minimum for
overlap of oven
top and 1V4"
(3.2 cm) overlap
of oven bottom
of cutout
Allow a minimum
of 21" (53.3 cm) for
clearance to adjacent
drawers,
walls, etc. when
door is open
cabinet)
---t
"
(53.3 cm)I'Y_'_
corners,
adjacent
Cabinet Width
_--_
Recommended
cutout location
from floor 32 1/2"
(82,6 cm)
--
Cabinet
Width
30" (76,2 cm)
if the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 150 Ibs (68 Kg).
Suitable
Bracing
to Support
Runners
--
-_(s4
21 s/8.9 cm) over
\
Centerline
of Cabinet
NOTE: if marks, blemishes
or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered,
These ovens are not approved
stackable installations.
2"x4"
(5 cm x 10 cm
or equivalent
runners
level
with bottom
of cutout
Side by Side Installations
Install two wall ovens in separate cutouts.
Allow 2" (5.1 cm) min. between cutouts.
Cutouti 2"(5.1 cm)
Cutout Observe all
Min.
Observe all
dimensions I_ll'='=='==='='=i_ dimensions
and
and
I
requirements.
requirements.J
for
9
Installation instructions
Cutoutfor 30"(76.2
cm)
Ovensonly
For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models
Cutout
Width
28 1/2" (72.4 cm)
Min.
-,_
28 5/8" (72.7 cm)
Max.
9 1/2"
(24.1 cm)
Junction Box
n
(junction box
may be
located
Location in
adjacent
cabinet)
_t
/"
Allow 11116"
(1.75 cm) for
overlap of oven
over side edges
of cutout
Allow a minimum
of 21" (53.3 cm) for
clearance to adjacent
\
21" (53.3 cm)_
Cutout Depth
23 1/2" (59.7 cm) Min.
Cutout Width
28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
Cutout Height
I
47" (119.4 cm)
Min.
to Bottom of
Junction Box
Cutout
AHow 1" (2.5 cm)
minimum for
overlap of oven
top and 11/4"
(3 2 cm) over ap
of oven bottom
-
ofcutout
51 13/16" (131.6 cm) Min.
51 15116" (131.9 cm) Max.
Inside Walls
I
Must Be At
Least 28 1/2"
(72.4 cm) Wide
d rawers_
walls, etc. when
door is open
30" (76.2 cm)
Recommended
Cutout Location
from Floor
12" (30.5 cm)
.__
Between
corners_
Cabinet Width
only.
Height
51 13/16" 131.6 cm)
Min.
51 15/16" (131.9 cm)
Max
I
NOTE: If the cabinet does not
have a front frame and the sides
are less than 314" (1.9 cm) thick,
shim both sides equally to
establish
the cutout width.
" F - _-I
-/1 Recommended
--_ 30_
I cutout location
(76.2 cm)"_;,_from
f!oor 12" (30.5 cm)
Cabinet
_'_..L,_.
Width
I
if the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
double ovens, the runners and braces
must support 275 Ibs (124 Kg).
Suitable
Bracing -to Support
Runners
NOTE: If marks, blemishes
or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered,
10
2"x4"
(Scm
xtOcrn)
or equiva|eut
runners
|eve|
with bottom
of cutout
Installation instructions
Cutout for 30"(76.2 Single
only Under Coun :r
lit-in Ovens
For JTP30, JTPT0, PT916, PT920, ZET938 models only.
Gas or electric cooktops may be installed over this oven. See
cooktop installation instructions for cutout size. See label on
top of oven for approved cooktop models.
240V / 208V
Junction Box
\
25" (63.5
Location (junction
box may be in
adjacent cabinet)
9 1/2"
(24.1 cm)
cm)
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
Gas and electrical connections
for gas cooktop must be located
in an adjacent accessible
location to the right.
- 28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
overlap
(2.5 cm)
top
Of oven_
-. 11/16" (1.8 cm)
_,"- overlap side edges
of cutout and
22" (55.9 cm) Min.
Above Support
Platform
36" (91.4 cm)
Typical
Countertop
Height
-- 1 114" (3.2 cm)
overlap bottom
Of oven,
24" (61 cm)
4" (10.2 cm)
Typical
Toekick
NOTE: This oven is only
approved
to be installed under
the specific models as labeled
on this unit.
Side by Side Installations
Cutout - ] 2" (5.1 cm)
Cutout Observe all|
Min.
Observe all
dimensions
d im e ns io n s_-,ql,,,,===,,,===,=,lm_"
and
and
|
requirements.
requirements.J
Install two wall ovens in separate cutouts.
Allow 2" (5.1 cm) min. between cutouts.
11
Cabinetry
Cutout for 30"(76.2c_)
Single or Double
L_i -in Ovens only- Over a
_rrning Drawer
For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960,
ZET938, ZET958 models only.
Single 30" (76.2 cm)
Oven Over a Warming
Drawer
Double 30" (76.2 cm)
Oven Over a Warming
Drawer
Block Against
Rear Wall Per Warming
Drawer Requirement
Anti-Tip Block
Against Rear
Wall Per
Warming
2" (5J cm)
IVlin.
Drawer
Requirement
NOTE: Install the
2" (5.1 cm)
oven only with
specific models
listed on the label
located on top of
the oven.
Per Warming
Drawer
Requirement
IVlin.
Per Warming
Drawer
Requirement
1" (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
1" (2.5 cm) Min. Above Toekick
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height.
When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
12
Cabinetry
Cutoutfor 30"<76.2
o_)SingleOvensonlyBelowan Advantium or _-rowaveOven
or Betweenan Advantiumor crowave
Ovenand a WarmingDrawer
For JTP30, JTP70, PT916, PT920, ZET938
Single 30" (76.2 cm) Oven
Below an Advantium or
Microwave Oven
models only.
Single 30" (76.2 cm) Oven
Between an Advantium or
Microwave Oven and a
Warming Drawer
Per Advantium
Microwave Oven
Requirement
__"
2" (5.1 cm) Min.
(5.1 cm) Min,
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
2" (5.1 cm) Min.
Per Warming
Drawer
Req
NOTE: The middle rail separating the two
openings may need to be larger than the 2"
(5.1 cm) m=nimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the
2" (5.1 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
Combined Advantium or Microwave
Oven and Wall Oven Installation:
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
• Refer to the Advantium or microwave
oven installation instructions for electrical
requirements of that product.
These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
Warming DrawerCombinedwith
Advantiumor MicrowaveOvenand
SingleOven:
Install a separate 120V, 60Hz, properly
grounded receptacle, See installation
instructions packed with each product
for specific requirements,
13
Installation instructions
Electrical Connections
ATTENTION
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
iNSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
With the oven supported on a table or
platform in front of the cabinet opening,
connect the flexible conduit to the
electrical junction box as shown below.
Position the conduit in such a manner
that it will lie on top of the oven in
a natural loop when the oven is
installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.
DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be
securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper
size is obtained.
Junction Box
Location
NOTE TO ELECTRiCiAN:
The 3 power
leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures
much higher than the temperature
rating
of household wiring. The current carrying
capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.
Conduit
WARNING: Improper
Place oven on a
connection of aluminum house
wiring to copper leads can
result in an electrical hazard or fire.
Use only connectors designed
for
joining copper to aluminum and follow
the manufacturer's
recommended
procedure closely.
support to assist i
connecting conduit
14
II
Strain Relief Clamp
(not included)
must be used at
Junction Box
Installation instructions
New Construction and
Four=Conductor Branch
Circuit Connection
• When installing in new construction,
Three=Conductor Branch
Circuit Connection
When connecting to a three-conductor
circuit, if local codes permit:
or
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to
the branch circuit neutral (white or gray
in color), using a wire nut.
• When installing in a mobile home, or
• When installing in a recreational
vehicle,
branch
or
• When local codes do not permit grounding
through neutral:
a. Cut the neutral (white) lead from the crimp.
Re-strip the neutral (white) lead to expose
the proper length of conductor.
[__ound
and
\..j__ Jo.o.:,
Box
oo
bo Connect the oven red lead to the branch
circuit red lead in accordance with local
codes, using a wire nut.
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using a wire nut. If the residence
red, black or white leads are aluminum
conductors, see WARNING on page 14.
b. Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING on page 14.
d. Install Junction
c. Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray)
in accordance with local codes, using a
wire nut.
d. Connect the oven red lead to the branch
circuit red lead and the oven black lead to
the branch circuit black lead in accordance
with local codes, using wire nuts. If the
residence red, black or white leads are
aluminum conductors, see WARNING
on page 14.
e. Install Junction
Box Cover.
15
Box Cover.
Installation instructions
Securing the Oven
Sliding the Oven into the
Opening
m
In
e Openin
Drilling the Pilot Holes and
Mounting the Oven
a. Loop (do not tie) a 36" (91 cm) string
around the conduit before the oven is slid
into place. This will keep the conduit from
falling behind the oven.
NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go
and centered.
a. Drill through the mounting holes (top and
bottom) of the side trim, for the #8 screws
provided.
Pull out on
string loop
while pushing
the oven into
the cabinet
Mounting
Hole
Locations
(Hole
may vary)
b. Lift oven into cabinet cutout using the oven
opening as a grip. Carefully push against
oven front frame. Do not push against
outside edges.
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the
oven in a natural loop.
The screws must
be a minimum of
1/4" (6 mm) from
the front of the
cutout.
_k WARNING:
Mounting
screws must be used.
Failure to
do so could result in the oven
falling out of the cabinet causing
serious injury.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.
b. Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use #8 x 3/4" particle board screws.
These may be purchased at any hardware
store.
16
Installation instructions
[_
Preparing for the Bottom
Trim Installation
a. With oven installed, take the bottom trim
and center it on the bottom front edge of
the cabinet opening.
b. Using the trim
as a template,
mark the center
of each slot
(two total) where
the mounting holes
will be drilled.
c. Remove the trim.
d. Drill pilot holes into
the center of each
template mark.
a=
For 27" (68.6 cm)
models with Lower
Trim in Position
Mark (2)
Hole Locations
here
Installing the Metal
Bottom Trim
Place the bottom metal trim centered over
the pre-drilled mounting holes. Tape the
edges of the trim down to maintain the
alignment.
b. Using two trim screws provided, secure
the bottom trim to the bottom edge of the
cabinet.
Trim Screw Locations for
, /Trim
Side
._
27"(68._cm)models
with _.._
* Remove
Lower Trim
Before
Pre-drilling
Mounting
Holes
:or 30" (76.2 cm)
models with
Lower Trim in
Position, Mark
(2) Mounting
Hole Locations
here
1'
Trim -..__
Trim Screw Locations for
30" (76.2 cm) models with
Lower Trim
IMPORTANT:
if this unit is ever
removed from the cabinet or the oven
is ever pulled out for service, the trim
must be removed first or damage to
the trim will occur.
17
Installation instructions
Replacing the Oven Door
NOTE: The oven door is heavy. You
may need help lifting the door high
enough to slide it into the hinge slots.
Do not lift the door by the handle.
[=_
Open the oven door as far as it
will open.
[=_
Push the hinge locks up against the
front frame of the oven cavity, to the
locked position,
Hinge in
Locked Position
Lift the oven door by
placing one hand on
each side. The door is
heavy, so you may need
help. Do not lift the door
by the handle.
Notch of Hinge
Securely Fitted
into
Hinge Slot
[=_
F_
With the door at the same angle as
the removal position, which is most of
the way closed, seat the notch of the
hinge arm into the bottom edge of the
hinge slot. The notch of the hinge arm
must be fully seated into the bottom
of the slot.
Hinge Arm
Bottom
of Slot
Edge
Hinge Notch
18
Close the oven door.
Installation instructions
Pre-Test C ec
Remove all protective
and any stickers.
ist
Check that the bottom trim is installed
properly (see page 17).
film, if present,
Check to be sure that all wiring is
secure and not pinched or in contact
with moving parts.
Check to be sure the mounting screws
are installed and flush with the side trim
(see page 16).
Operation Checklist
Remove all items from the inside
of the oven.
NOTE TO ELECTRICIAN:
The power
leads supplied with this appliance
are UL recognized
for connections
to larger gauge household wiring.
The insulation of these leads is
rated at temperatures
much higher
than the temperature
rating of
household wiring. The current
carrying capacity of a conductor
is governed
by the wire gauge and
also the temperature
rating of the
insulation around the wire.
Check that conduit is securely
connected to the junction box.
Turn on the power to the oven. (Refer
to your Owner's Manual.) Verify that
the bake and broil units, and all
cooking functions operate properly.
Check that the circuit breaker is not
tripped nor the house fuse blown.
NOTE: ALUMINUM
See your Owner's Manual for
troubleshooting
list.
A.
WIRING
WARNING: IMPROPER
CONNECTION
OF ALUMINUM
HOUSE WIRING TO THE COPPER
LEADS CAN RESULT IN AN
ELECTRICAL
HAZARD OR FIRE.
B,
Splice copper wires to aluminum
wiring using special connectors
designed
and UL approved
for
joining copper to aluminum,
and follow the manufacturer's
recommended
connector
procedure
closely.
NOTE: Wire used, location and
enclosure
of splices, etc., must
conform to good wiring practice
and local codes.
19
Notes
20
Modelos de 27" (68,6 cm)
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938, ZEK958
Modelos de 30" (76,2 cm)
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958
I
Visite nuestro sitio en la Web: ge.com
Horno de pared empotrado
vigentes.
•iATENCION AL
INSTALADORI
Moldura de fondo
metalica de 27"
(68,6 cm)
4__
@
TLet__aSpar a
Cord6n de 36" (91 cm)
WBO7T10579 - SS
Montaje de moldura de rondo
Una broca de 1/8" (3 mm) para
taladro
31-10647-3
11-07 JR
o manual
DE SEGURIDAD
Para su seguridad
cont.
podria
e incluso
Potencia KW
208V
<4,8 KW
<4,1 KW
20 Amp
4,9 KW-7,2 KW
4,3 KW-6,2 KW
30 Amp
7,3 KW-9,6 KW
6,3 KW-8,3 KW
40 Amp
9,7 KW-12,0 KW 8,4 KW-10,4 KW
50Amp
--
Ubicaci6n
=
!
...................
I
iTODA LA INFORMACION
PARA LA
INSTALACION
EN LAS PAGINAS
SIGUIENTES
ES PARA SER USADA EN
LA INSTALACION
DE HORNOS DE UNA
O DOS UNIDADES!
/_
Posici6n
abierta de
la bisagra
Brazo de
la bisagra
iNO LEVANTE LA PUERTA
LA EMPUNADURA!
POR
-<_
L
--
_-J
_
?
Bisagra sale
de la ranura
oderecho
Ancho del_
gabinete _
27" (68,6 cm) i
_
¢
25" (63,5 cm) Min.
25 1/4" (64,1 cm)
"i_'
!
22" (55,9 cm)
iAItura
idel corte
i27 5/8" (70,2 cm) Min.
__n
iiiiii!i_i!iii}(!!_l!
20" (50,8 cm)
'4 cm)M_x.
Ancho del
gabinete
27" (68,6 cm)
32 1/2" (82,6 cm)
23 1/2" (59,7 cm) Min.
25" (63,5 cm) Min.
25 1/4" (64,1 cm) Mbx.
Altura de corte
27 5/8" (70,2 cm) Min.
28 1/8" (71,4 cm) Mbx.
alterna
......
piso 32 1/2"
(82,6 cm)
1
!
24" (61 cm)
I_•_
18" (45,7 cm)
27" (68,6 cm)
Ancho del _
gabinete _
27" (68,6 cm).
Ancho del
gabinete
J.
I -i-._
'_,i'_
_/-
13 114"(33,7 cm)
25 1/4" (64,1 cm) M_x.
2" x 4"
(5 cm x t0 cm)
o correderas
equivalentes
23 518" (60 cm) Min.
Altura de corte
25" (63,5 cm) Min.
25 1/4" (64,1 cm) Max.
49 11/16" (126,2 cm) Min.
50 1/8" (127,3 cm) Max.
20" (50,8
j_oJooooi -'I
27" (68,6 cm)
Abrazaderas
--
25" (63,5 cm)
25" (63,5 cm) Min.
25 1/4" (64,1 cm) Mbx.
1.
27 5/8" (70,2 cm) Min.
28 118" (71,4 cm) M_x.
s
:i
36" (91,4 cm)
Altura tipica del
gabinete
24" (61 cm)
4" (10,2 cm)
Zocalo tipico
Gabinetes
I_1Disyuntor
para27"(68,6cm)Solamente parahornos
individuales
- Debajo
deunAdvantium
odeun
horno
demicroondas
oEntreunhorno
Advantium
o
unhornodemicroondas
yGaveta
decalentamiento
Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente.
Hornoindividualde27"(68,6cm)
debajode unhornoAdvantiumo
un hornode microondas
Por Advantium
de microondas
o horno
requisitos
2" (5,1 cm) Min.
Hornoindividualde 27"(68,6cm)
EntreunhornoAdvantiumo
unhornode microondasy
unagavetadecalentamiento
Por Advantium
de microondas
o horno
requisitos
2" (5,1 cm) Min.
2" (5,1 cm) Min.
9 1/2"
(24,1 cm)
-_
_
-- .
--
Mbx_
/
_
I
I
/
I
I
I
I
(72,4 cm)
de ancho
i
27 1/4"
_,
(69,2 cm) Min.
27 5/16"
(69,4 cm) Mbx.
"- '_ I
32 112"(82,6 cm)
23 112" (59,7 cm) Min.
28 112"(72,4 cm) Min.
28 518" (72,7 cm) Max.
Altura de corte
27 1/4" (69,2 cm) Min.
27 5/16" (69,4 cm) Max.
--NOTA:Si el gabinete no tiene un marco
30" (76,2 cm)
gabinete
Ubicaci6n
Profundidad
--
2" x 4"
(5 cm x 10
Cm)
Ancho del
gabinete
30" (76,2 cm)
O
Abrazaderas
cm) Linea de
centro sobre
\
gabinetes
Corte para los hornos de dos
unidades de 30" (76,2 cm)solamente
Para los modelos JTP35, JTP55, JTP75, PT956, PT960, ZET958 solamente.
Ancho
del corte
28 1/2"
(72,4 cm) Min.
_r28 5/8"
(72,7 cm) M&x.
9 112" (24,1 cm)
M&x.
I
F
[
I
[
[
)_-
_
12" (30,5 cm)
23 112"(59,7 cm) Min.
28 112"(72,4 cm) Min.
I
28 518" (72,7 cm) Max,
I
I
Altura de corte
I
51 13/16" (131,6 cm) Min.
I
I
(72,4 cm)
de ancho
(131,6 cm) Min,
51 15/16"
(131,9 cm_ M&x
"
"
"
i
(3,2cm)
por
21"
30" (76,2 cm)
I
I :
I
[
L
I
I
'
i
--
(53,3 cm
2" x 4"
(5 cm x 10
cnl)
A_cho del_'_
_ga_l;ine_e ' _1
/ I
I
30" (76,2 cm)
10
O
- 28 112" (72,4 cm) Min
28 518" (72,7 cm) M_x..
27 114" (69,2 cm) Min.
27 5116" (69,4 cm) M_x. :::L_.
22" (55,9 cm) Min.
Por encima de
la plataforma
de soporte
36" (91,4 cm)
Altura tipica del
gabinete
(10,2 cm)
Z6calo tipico
separados.
Deje 2" (5,1 cm) min.
11
Horno individual de 30"
12
Gabinetes
Disyuntor
para30"(76,2cm)Solamente parahornos
individuales
- Debajo
deunAdvantium
o deun
hornodemicroondas
o EntreunhornoAdvantium
o
unhornodemicroondas
y Gavetadecalentamiento
Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente.
Hornoindividualde30"(76,2cm)
debajode unhornoAdvantiumo
un hornode microondas
Hornoindividualde 30"(76,2cm)
EntreunhornoAdvantiumo
unhornode microondasy
unagavetadecalentamiento
Por Advantium
Por Advantium o horno
de microondas requisitos
2" (5,1 cm) Min.
2" (5,1 cm) Min.
microondas
requisi
Nota: Instale el
L_.:_:_--....
i
I
II
I
I
I L_
2" (5,1 cm) Min.
I ,_....... 111
II
.......
_1_
J
14
i---
-i
b=
caja
C=
'--'
a,
J
16
I_]
a.
b°
* Retire la
moldurainferior
inferior
antes de
pretaladrar
_o, orifieios
de moetaje
__S_ll lie,
_-_llllHIll'
_llllHIIJ
_
_J
"_,,_'_
J
IIHII
tS
I'l;
Moldura
lateral
o, ura._
moldura
de fondo
aqui
17
_'-_
_]
18
[_
etire cualquier
cinta este
de proteccion
etiqueta
que todavia
presente.
y
[_
NOTA AL ELECTRICISTA:
articulo del interior
y
NOTA: CABLEADO
A.
DE ALUMINIO
ADVERTENCIA:
UNA CONEXION
DEL CABLEADO
INAPROPIADA
DEL ALUMINIO
RESIDENCIAL CON EL COBRE,
PODR|A RESULTAR EN PROBLEMAS
SERIOS O EN INCENDIO.
para
B=
19
Notas
20

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project