LG LFCS25663S Owner's manual

LG LFCS25663S Owner's manual
ENGLISH ESPAÑOL FRANÇAIS
OWNER’S MANUAL
BOTTOM FREEZER
REFRIGERATOR
Please read this manual carefully before operating
your set and retain it for future reference.
MANUAL DE USUARIO
MANUEL D’UTILISATEUR
*=color number/número de color/numéro de couleur
LFCS25663*
P/No. MFL67306603-3
ww w.lg.com
Copyright © 2014 - 2017 LG Electronics Inc. All Rights Reserved. / Copyright © 2014 - 2017 LG Electronics Inc.
Todos los Derechos Reservados. / Copyright © 2014 - 2017 LG Electronics Inc. Tous droits réservés
LIMITED WARRANTY
LG ELECTRONICS U.S.A., INC.
LG REFRIGERATOR LIMITED WARRANTY - U.S.A.
ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT REQUIRES YOU
AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT, UNLESS YOU CHOOSE TO OPT
OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED
“PROCEDURE FOR RESOLVING DISPUTES” BELOW.Should your LG Refrigerator ("Product") fail due to a defect in materials or workmanship under normal and proper use, during the warranty period set forth below, LG Electronics (“LG”) will, at its
option, repair or replace the Product. This limited warranty is valid only to the original retail purchaser of the Product and
applies only when purchased and used within the United States including U.S. Territories.
Refrigerator/Freezer
WARRANTY PERIOD
Sealed System
(Condenser, Dryer, Connecting
Tube and Evaporator)
One (1) year from the Five (5) years from the date
date of original retail of original retail purchase
purchase
Parts and Labor
Parts and Labor
(internal/ functional
parts only)
Compressor
Five (5) years from the Linear / Inverter Compressor Only : Parts
date of original retail Only for years 6-10 from the date of
original retail purchase (Consumer will
purchase
be charged for labor)
Parts and Labor
ţ3FQMBDFNFOUQSPEVDUTBOEQBSUTBSFXBSSBOUFEGPSUIFSFNBJOJOH portion of the original warranty period or ninety (90)
days, whichever is greater.
ţ3FQMBDFNFOUQSPEVDUTBOEQBSUTNBZCFOFXSFDPOEJUJPOFESFGVrbished, or otherwise factory remanufactured.
ţ1SPPGPGPSJHJOBMSFUBJMQVSDIBTFTQFDJGZJOHUIF1SPEVDUNPEFM and date of purchase is required to obtain warranty service
under this limited warranty.
EXCEPT TO THE EXTENT PROHIBTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ON THE PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THE
ABOVE LIMITED WARRANTY. UNDER NO CIRCUMSTANCES SHALL LG OR ITS U.S. DISTRIBUTORS/DEALERS BE
LIABLE FOR ANY INDIRECT, INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR PUNITIVE DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST GOODWILL, LOST REVENUES OR PROFITS, WORK STOPPAGE, IMPAIRMENT OF OTHER
GOODS, COST OF REMOVAL AND REINSTALLATION OF THE PRODUCT, LOSS OF USE, OR ANY OTHER DAMAGES
WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. LG’S TOTAL LIABILITY, IF ANY, SHALL NOT EXCEED THE
PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above exclusions or limitations may not apply to you. This limited warranty gives you specfic
legal rights and you may also have other rights that vary from state to state.
THIS LIMITED WARRANTY DOES NOT COVER:
ţ4FSWJDFUSJQTUPEFMJWFSQJDLVQPSJOTUBMMFEVDBUFIPXUPoperate, correct wiring, or correct unauthorized repairs.
ţ%BNBHF or failure of the Product to perform during power failures and interrupted or inadequate electrical service.
ţ%BNBHF or failure caused by MFBLZ or CSPLFO water pipes, frozen water pipes, restricted drain lines, inadequate or
interrupted water supply or inadequate supply of air.
ţ%BNBHFSFTVMUJOHGSPNPQFSBUJOHUIFQSPEVDUJOBDPSSPTJWFBUNosphere or contrary to the product owner’s manual.
ţ%BNBHF or failure to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts of God, or any
other causes beyond the control of LG.
ţ%BNBHFPSGBJMVSFDBVTFECZVOBVUIPSJ[FENPEJżDBUJPOPSBMUFSBtion, or if used for other the intended purpose.
ţ%BNBHF or failure resulting from misuse, abuse, improper installation, repair, or maintenance. Improper repair includes use
of parts not authorized by LG. Improper installation or maintenance includes installation or maintenance contrary to the
Product owner’s manual.
ţ%BNBHFPSGBJMVSFDBVTFECZJODPSSFDUFMFDUSJDBMDVSSFOUWPMUage, or plumbing codes.
ţ%BNBHF or failure caused by transportation and handling, including scratches, dents, chips, and/or other damage to the
finish of the product, unless such damage is reported within one
XFFLPGEFMJWFSZ
ţ%BNBHFPSNJTTJOHJUFNTUPBOZEJTQMBZPQFOCPYPSEJTDPVOUFd Product.
ţ3FGVSCJTIFE1SPEVDUPSBOZ1SPEVDUTPMEŞ"T*TşŞ8IFSF*TşŞ8JUIBMM'BVMUTşPSTJNJMBSEJTDMBJNFS
ţ1SPEVDUTXJUIPSJHJOBMTFSJBMOVNCFSTUIBUIBWFCFFOSFNPWFEaltered, or cannot be readily determined.
ţ*ODSFBTFTJOVUJMJUZDPTUTBOEBEEJUJPOBMVUJMJUZFYQFOTFT
ţ"OZOPJTFTBTTPDJBUFEXJUIOPSNBMPQFSBUJPO
ţ6TFPGBDDFTPSJFTFHXBUFSżMUFSTFUD
DPNQPOFOUTPSDonsumable cleaning products that are not authorized by LG.
ţ3FQMBDFNFOUPSMJHIUCVMCTżMUFSTPSBOZDPOTVNBCMFQBSUT
ţ8IFO Product is used for other than normal and proper household use (e.g. commercial or industrial use, offices, and
recreational facilities or vehicles)or contrary to the instructions outlined in the Product’s owner’s manual.
ţ$PTUTBTTPDJBUFEXJUISFNPWBMBOESFJOTUBMMBUJPOPGZPVS1SPEVct for repairs.
ţ4IFMWFT door bins, drawers, handle and accessories, except for internal/functional parts covered under this limited
warranty.
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
TO 0#5"*/ 8"33"/5: 4&37*$& "/% "%%*5*0/"- */'03."5*0/$BMM 1-800-243-0000 and select the appropriate
option from the menu or visit our website at http://www.lg.com or by mail: LG Electronics Customer Service P.O. Box
)VOUTWJMMF"-"55/$*$
1
LIMITED WARRANTY
PROCEDURE FOR RESOLVING DISPUTES:
ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY WAY TO THIS LIMITED WARRANTY
OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING ARBITRATION, AND NOT IN A COURT
OF GENERAL JURISDICTION. BINDING ARBITRATION MEANS THAT YOU AND LG ARE EACH WAIVING THE RIGHT
TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS ACTION.
Definitions. For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc., its parents, subsidiaries
and affiliates, and each of their officers, directors, employees, agents, beneficiaries, predecessors in interest, successors,
assigns and suppliers; references to “dispute” or “claim” shall include any dispute, claim or controversy of any kind
whatsoever (whether based in contract, tort, statute, regulation, ordinance, fraud, misrepresentation or any other legal or
equitable theory) arising out of or relating in any way to the sale, condition or performance of the product or this Limited
Warranty.
Notice of Dispute. In the event you intend to commerce an arbitration proceeding, you must first notify LG in writing at least 30
days in advance of initiating the arbitration by sending a letter to LG at LG Electronics, USA, Inc. Attn: Legal DepartmentArbitration 1000 Sylvan Ave, Englewood Cliffs 07632. You and LG agree to engage in good faith discussions in an
attempt to amicably resolve your claim. The notice must provide your name, address, and telephone number; identify the
product that is the subject of the claim; and describe the nature of the claim and the relief being sought. If you and LG
are unable to resolve the dispute within 30 days, either party may proceed to file a claim for arbitration.
Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during the 30 day period
after sending written notice to LG, you and LG agree to resolve any claims between us only by binding arbitration on an
individual basis, unless you opt out as provided below. Any dispute between you and LG shall not be combined or
consolidated with a dispute involving any other person’s or entity’s product or claim. More specifically, without limitation of
the foregoing, any dispute between you and LG shall not under any circumstances proceed as part of a class or representative action. Instead of arbitration, either party may bring an individual action in small claims court, but that small claims
court action may not be brought on a class or representative basis.
Arbitration Rules and Procedures. To begin arbitration of a claim, either you or LG must make a written demand for
arbitration. The arbitration will be administered by the American Arbitration Association (“AAA”) and will be conducted
before a single arbitrator under the AAA’s Consumer Arbitration Rules that are in effect at the time the arbitration is
initiated (referred to as the “AAA Rules”) and under the procedures set forth in this section. The AAA Rules are available
online at www.adr.org/consumer. Send a copy of your written demand for arbitration, as well as a copy of this provision, to
the AAA in the manner described in the AAA Rules. You must also send a copy of your written demand to LG at LG
Electronics, USA, Inc. Attn: Legal Department- Arbitration 1000 Sylvan Avenue Englewood Cliffs, NJ 07632. If there is a
conflict berween the AAA Rules and the rules set forth in this section, the rules set forth in this section will govern. This
arbitration provision is governed by the Federal Arbitration Act. Judgment may be entered on the arbitrator’s award in any
court of competent jurisdiction. All issues are for the arbitrator to decide, except that issues relating to the scope and
enforceability of the arbitration provision and to the arbitrability of the dispute are for the court to decide. The arbitrator is
bound by the terms of this provision.
Governing Law. The law of the state of your residence shall govern this Limited Warranty and any disputes between us
except to the extent that such law is preempted by or inconsistent with applicable federal law.
Fees/Costs. You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand for AAA unless
you seek more than $25,000 in damages, in which case the payment of these fees will be governed by the AAA Rules.
Except as otherwise provided for herein, LG will pay AAA filing, administration and arbitrator fees for any arbitration
initiated in accordance with the AAA Rules and this arbitration provision. If you prevail in the arbitration, LG will pay your
attorneys’ fees and expenses as long as they are reasonable, by considering factors including, but not limited to, the
purchase amount and claim amount. Notwithstanding the foregoing, if applicable law allows for an award of reasonable
attorneys’ fees and expenses, an arbitrator can award them to the same extent that a court would. If the arbitrator finds
either the substance of your claim or the relief sought in the demand is frivolous or brought for an improper purpose (as
measured by the standards set forth in Federal Rule of Civil Procedure 11(b)), then the payment of all arbitration fees will
be governed by the AAA Rules. In such a situation, you agree to reimburse LG for all monies previously disbursed by it
that are otherwise your obligation to pay under the AAA Rules. Except as otherwise provided for, LG waives any rights it
may have to seek attorneys’ fees and expenses from you if LG prevails in the arbitration.
Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration conducted solely on
the basis of (1) documents submitted to the arbitrator, (2) through a telephonic hearing, or (3) by an in-person hearing as
established by the AAA Rules. If your claim exceeds $25,000, the right to a hearing will be determined by the AAA
Rules. Any in-person arbitration hearings will be held at a location within the federal judicial district in which you reside
unless we both agree to another location or we agree to a telephonic arbitration.
Opt Out. You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can require the other to
participate in an arbitration proceeding. To opt out, you must send notice to LG no later than 30 calendar days from the
date of the first consumer purchaser’s purchase of the product by either: (i) sending an e-mail to [email protected], with
the subject line: “Arbitration Opt Out” or (ii) calling 1-800-980-2973. You must include in the opt out e-mail or provide
by telephone: (a) your name and address; (b) the date on which the product was purchased; (c) the product model name
or model number; and (d) the serial number (the serial number can be found (i) on the product; or (ii) online by accessing
https://www.lg.com/us/support/repair-service/schedule-repair-continued and clicking on “Find My Model & Serial
Number”).
You may only opt out of the dispute resolution procedure in the manner described above (that is, by e-mail or telephone);
no other form of notice will be effective to opt out of this dispute resolution procedure. Opting out of this dispute
resolution procedure will not affect the coverage of the Limited Warranty in any way, and you will continue to enjoy the full
benefits of the Limited Warranty. If you keep this product and do not opt out, then you accept all terms and conditions of
the arbitration provision described above.
3
GARANTÍA LIMITADA
PROCEDIMIENTO PARA RESOLVER CONFLICTOS:
4
LIMITED WARRANTY
LG ELECTRONICS CANADA, INC.
LG REFRIGERATOR LIMITED WARRANTY - Canada
ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT REQUIRES YOU
AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT, UNLESS THE LAWS OF YOUR
PROVINCE OR TERRITORY DO NOT PERMIT THAT, OR, IN OTHER JURISDICTIONS, IF YOU CHOOSE TO OPT OUT. IN
ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES” BELOW.
Should your LG Refrigerator ("Product") fail due to a defect in materials or workmanship under normal and proper use, during
the warranty period set forth below, LG Electronics Canada, Inc. (“LGECI”) will, at its option, repair or replace the Product upon
receipt of proof of the original retail purchase. This limited warranty is valid only to the original retail purchaser of the Product
and applies only to a Product distributed, purchased and used within Canada, as determined at the sole discretion of LGECI.
WARRANTY PERIOD (Note: If the original date of purchase cannot be verified, the warranty will begin sixty
(60) days from the date of manufacture)
Linear / Inverter
Sealed
System (Condenser, Dryer, Connecting Tube
Refrigerator
Compressor
and Evaporator)
Seven (7) years from
Ten (10) years from the
One (1) year from the
One (1) year from the
the date of original retail
date of original retail
date of original retail
date of original retail
purchase
purchase
purchase
purchase
Parts and Labor (internal/
functional parts only)
Parts only (Consumer will
be charged for labor)
Parts and Labor
Part only (Consumer will
be charged for labor)
ţ3FQMBDFNFOUQSPEVDUTBOEQBSUTBSFXBSSBOUFEGPSUIFSFNBJOJOH portion of the original warranty period or ninety (90) days,
whichever is greater.
ţ3FQMBDFNFOUQSPEVDUTBOEQBSUTNBZCFOFXSFDPOEJUJPOFESFGVrbished, or otherwise factory remanufactured, all at the
sole discretion of LGECI.
ţ1SPPGPGPSJHJOBMSFUBJMQVSDIBTFTQFDJGZJOHUIF1SPEVDUNPEFM and date of purchase is required to obtain warranty service
under this Limited Warranty..
LGECI’S SOLE LIABILITY IS LIMITED TO THE LIMITED WARRANTY SET OUT ABOVE. EXCEPT AS EXPRESSLY
PROVIDED ABOVE, LGECI MAKES NO, AND HEREBY DISCLAIMS, ALL OTHER WARRANTIES AND CONDITIONS
RESPECTING THE PRODUCT, WHETHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND NO REPRESENTATIONS SHALL BE BINDING ON LGECI. LGECI DOES NOT AUTHORIZE ANY PERSON TO CREATE OR ASSUME FOR IT
ANY OTHER WARRANTY OBLIGATION OR LIABILITY IN CONNECTION WITH THE PRODUCT. TO THE EXTENT THAT
ANY WARRANTY OR CONDITION IS IMPLIED BY LAW, IT IS LIMITED TO THE WARRANTY PERIOD SET OUT ABOVE.
UNDER NO CIRCUMSTANCES SHALL LGECI, THE MANUFACTURER OR DISTRIBUTOR OF THE PRODUCT, BE LIABLE
FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, DIRECT, INDIRECT, PUNITIVE OR EXEMPLARY DAMAGES,
INCLUDING, WITHOUT LIMITATION, LOSS OF GOODWILL, LOST PROFITS, LOSS OF ANTICIPATED PROFITS, LOST
REVENUE, LOSS OF USE, OR ANY OTHER DAMAGE, WHETHER ARISING DIRECTLY OR INDIRECTLY FROM ANY
CONTRACTUAL BREACH, FUNDAMENTAL BREACH, TORT OR OTHERWISE, OR FROM ANY ACTS OR OMISSIONS.
LGECI’S TOTAL LIABILITY, IF ANY, SHALL NOT EXCEED THE PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.
This Limited Warranty gives you specific legal rights. You may also have other rights that vary from province to province
depending on applicable provincial laws. Any term of this Limited Warranty that negates or varies any implied condition or
warranty under provincial law is severable where ot conflicts with such provincial law without affecting the remainder of this
warranty’s terms.
THIS LIMITED WARRANTY DOES NOT COVER:
ţ4FSWJDF trips to i) deliver, pick up, or install or; educate on how to operate the Product; ii) correct wiring or plumbing; or iii)
correct unauthorized repairs or installations of the Product;
ţ%BNBHFPSGBJMVSFPGUIF1SPEVDUUPQFSGPSNEVSJOHQPXFSGBJMVres and interrupted or inadequate electrical service;
ţ%BNBHFPSGBJMVSFDBVTFECZMFBLZPSCSPLFOXBUFSQJQFTGSP[Fn water pipes, restricted drain lines, inadequate or interrupted
water supply or inadequate supply of air;
ţ%BNBHF or failure resulting from operating the Product in a corrosive atmosphere or contrary to the instructions outlined in
the Product’s owner’s manual;
ţ%BNBHF or failure to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts of God, or any other
causes beyond the control of LGECI or the manufacturer;
ţ%BNBHF or failure resulting from misuse, abuse, improper installation, repair, or maintenance of the Product. Improper repair
includes use of parts not authorized or specified by LGECI. Improper installation or maintenance includes installation or
maintenance contrary to the Product’s owner’s manual;.
ţ%BNBHF or failure cused by unauthorized modification or alteration of the Product, or if used for other than the intended
household purpose/use of the Product, or damage or failure resulting from any water leakage due to improper installation of
the Product;
ţ%BNBHFPSGBJMVSFDBVTFECZJODPSSFDUFMFDUSJDBMDVSSFOUWPMtage or plumbing codes;
ţ%BNBHF or failure caused by use that is other than normal household use, including, without limitation, commercial or industrial use, including use in commercial offices or recreational facilities, or as otherwise outlined in thev Product’s owner’s manual;
ţ%BNBHF or failure caused by the use of any accessories, components or cleaning products, including, without limitation, water
filters, that are not approved/authorized by LGECI;
ţ3FQMBDFNFOU of the water filter cartridge due to water pressure that is outside the specified operating range or due to excessive sediment in the water supply;
ţ%BNBHF or failure caused by transportation and handling, including scratches, dents, chips and/or other damage to the finish
of the Product, unless such damage results from defects in materials or workmanship and is reported to LGECI within one (1)
week of delivery of the Products;
ţ%BNBHFPSNJTTJOHJUFNTUPBOZEJTQMBZPQFOCPYSFGVSCJTIFEor discounted Product;
ţ3FGVSCJTIFE1SPEVDUPSBOZ1SPEVDUTPMEŞ"T*TşŞ8IFSF*Tş“With all Faults”, or any similar disclaimer;
ţ1SPEVDUT with original serial numbers that have been removed, altered or cannot be readily determined at the discretion of
LGECI;
ţ*ODSFBTFTJOVUJMJUZDPTUTBOEBEEJUJPOBMVUJMJUZFYQFOTFTJO any way associated with the Product;
LIMITED WARRANTY
ţ"OZOPJTFTBTTPDJBUFEXJUIOPSNBMPQFSBUJPOPGUIF1SPEVDU
ţ3FQMBDFNFOUPGMJHIUCVMCTżMUFSTGVTFTPSBOZPUIFSDPOTVNable parts;
ţ3FQMBDFNFOUPGBOZQBSUUIBUXBTOPUPSJHJOBMMZJODMVEFEXJUIthe Product;
ţ$PTUTBTTPDJBUFEXJUISFNPWBMBOEPSSFJOTUBMMBUJPOPGUIF1SPduct for repairs; and
ţ4IFMWFT door bins, drawers, handle and accessories to the Product, except for internal/functional parts covered under this
Limited Warranty.
ţ$PWFSBHF for "in Home" repairs, for products in-warranty, will be provided if the Product is within a 150 km radius from the
nearest authorized service center (ASC), as determined by LG Canada. If your Product is located outside a 150 km radius from
a ASC, as determined by LG Canada, it will be your responsibility to bring the Product, at your sole expense, to the ASC for
in-warranty repair.
All costs and expenses associated with the above excluded circumstances, listed under the heading, This Limited Warranty
Does Not Cover, shall be borne by the consumer.TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION,
PLEASE CALL OR VISIT OUR WEBSITE:Call 1-888-542-2623 (7 A.M. to 12 A.M., 365 days a year) and select the appropriate option from the menu, or. Visit our website at http://www.lg.com
PROCEDURE FOR RESOLVING DISPUTES:
EXCEPT WHERE PROHIBITED AT LAW, ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY
WAY TO THIS LIMITED WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING
ARBITRATION, AND NOT IN A COURT OF GENERAL JURISDICTION. EXCEPT WHERE PROHIBITED AT LAW, YOU AND
LG BOTH IRREVOCABLY AGREE TO WAIVE THE RIGHT TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS
ACTION.
Definitions. For the purposes of this section, references to “LG” mean LG Electronics Canada, Inc., its parents, subsidiaries and
affiliates, and each of their officers, directors, employees, agents, beneficiaries, predecessors in interest, successors, assigns
and suppliers; references to “dispute” or “claim” shall include any dispute, claim or controversy of any kind whatsoever (whether
based in contract, tort, statute, regulation, ordinance, fraud, misrepresentation or any other legal or equitable theory) arising out
of or relating in any way to the sale, condition or performance of the product or this Limited Warranty.
Notice of Dispute. In the event you intend to commence an arbitration proceeding, you must fist notify LG in writing at least
30 days in advance of initiating the arbitration by sending a letter to LG Electronics, Canada, Inc., Attn: Legal DepartmentArbitration, 20 Norelco Drive, North York, Ontario M9L 2X6. You and LG agree to engage in good faith discussions in an
attempt to amicably resolve your claim. The notice must provide your name, address, and telephone number; identify the
product that is the subject of the claim; and describe the nature of the claim and the relief being sought. If you and LG are
unable to resolve the dispute within 30 days, either day party may proceed to file a claim for arbitration.
Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during the 30 day period after
sending written notice to LG, you and LG agree to resolve any claims between you and LG only by binding arbitration on an
individual basis, unless you opt out as provided below, or you reside in a jurisdiction that prevents full application of this clause
in the circumstances of the claims at issue (in which case if you are a consumer, this clause will only apply if you expressly agree
to the arbitration). To the extent permitted by applicable law, any dispute between you and LG shall not be combined or
consolidated with a dispute involving any other person’s or entity’s product or claim. More specifically, without limitation of the
foregoing, except to the extent such a prohibition is not permitted at law, any dispute between you and LG shall not under any
circumstances proceed as part of a class or representative action. Instead of arbitration, either party may bring an individual
action in small claims court, but that small claims court action may not be brought on a class or representative basis except to
the extent this prohibition is not permitted at law in your province or territory of jurisdiction as it relates to the claims at issue
between you and LG.
Arbitration Rules and Procedures. To begin arbitration of a claim, either you or LG must make a written demand for arbitration.
The arbitration will be private and confidential, and conducted on a simplified and expedited basis before a single arbitrator
chosen by the parties under the provincial or territorial commercial arbitration law and rules of the province or territory of your
residence. You must also send a copy of your written demand to LG at LG Electronics, Canada, Inc., Attn: Legal DepartmentArbitration, 20 Norelco Drive, North York, Ontario M9L 2X6. This arbitration provision is governed by your applicable provincial
or territorial commercial arbitration legislation. Judgment may be entered on the arbitrator’s award in any court of competent
jurisdiction. All issues are for the arbitrator to decide, except that, issues relating to the scope and enforceability of the arbitration provision and to the arbitrability of the dispute are for the court to decide. The arbitrator is bound by the terms of this
provision.
Governing Law. The law of the province or territory of your residence shall govern this Limited Warranty and any disputes
between you and LG except to the extent that such law is preempted by or inconsistent with applicable federal or
provincial/territorial law. Should arbitration not be permitted for any claim, action, dispute or controversy between you and LG,
you and LG attorn to the exclusive jurisdiction of the courts of the province or territory of your residence for the resolution of
the claim, action, dispute or controversy between you and LG.
Fees/Costs. You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand for arbitration, LG will
promptly pay all arbitration filing fees unless you seek more than $25,000 in damages, in which case the payment of these
fees will be governed by the applicable arbitration rules. Except as otherwise provided for herein, LG will pay all filing, administration and arbitrator fees for any arbitration initiated in accordance with the applicable arbitration rules and this arbitration
provision. If you prevail in the arbitration, LG will pay your attorneys’ fees and expenses as long as they are reasonable, by
considering factors including, but not limited to, the purchase amount and claim amount. Notwithstanding the foregoing, if
applicable law allows for an award of reasonable attorneys’ fees and expenses, an arbitrator can award them to the same extent
that a court would. If the arbitrator finds either the substance of your claim or the relief sought in the demand is frivolous or
brought for an improper purpose (as measured by the applicable laws), then the payment of all arbitration fees will be governed
by the applicable arbitration rules. In such a situation, you agree to reimburse LG for all monies previously disbursed by it that
are otherwise your obligation to pay under the applicable arbitration rules. Except as otherwise provided for, LG waives any
rights it may have to seek attorneys’ fees and expenses from you if LG prevails in the arbitration.
Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration conducted solely (1) on the
basis of documents submitted to the arbitrator, (2) through a telephonic hearing, or (3) by an in-person hearing as established
6
LIMITED WARRANTY
by the applicable arbitration rules. If your claim exceeds $25,000, the right to a hearing will be determined by the applicable
arbitration rules. Any in-person arbitration hearings will be held at the nearest, most mutually-convenient arbitration location
available within the province or territory in which you reside unless you and LG both agree to another location or agree to a
telephonic arbitration.
Severability and Waiver. If any portion of this Limited Warranty (including these arbitration procedures) is unenforceable, the
remaining provisions will continue in full force and effect to the maximum extent permitted by applicable law. Should LG fail
to enforce strict performance of any provision of this Limited Warranty (including these arbitration procedures), it does not
mean that LG intends to waive or has waived any provision or part of this Limited Warranty.
Opt Out. You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can require the other to
participate in an arbitration proceeding. To opt out, you must send notice to LG no later than 30 calendar days from the date
of the first consumer purchaser’s purchase of the product by either (i) sending an e-mail to [email protected], with the subject
line: “Arbitration Opt Out;” or (ii) calling 1-800-980-2973. You must include in the opt out e-mail or provide by telephone: (a)
your name and address; (b) the date on which the product was purchased; (c) the product model name or model number; and
(d) the serial number (the serial number can be found (i) on the product; or (ii) online by accessing
https://www.lg.com/ca_en/support/repair-service/schedule-repair and clicking on “Find My Model & Serial Number”).
In the event that you “Opt Out”, the law of the province or territory of your residence shall govern this Limited Warranty and
any disputes between you and LG except to the extent that such law is preempted by or inconsistent with applicable federal
or provincial/territorial law. Should arbitration not be permitted for any claim, action, dispute or controversy between you and
LG, you and LG agree to attorn to the exclusive jurisdiction of the courts of the province or territory of your residence for the
resolution of the claim, action, dispute or controversy between you and LG.You may only opt out of the dispute resolution
procedure in the manner described above (that is, by e-mail or telephone); no other form of notice will be effective to opt out
of this dispute resolution procedure. Opting out of this dispute resolution procedure will not affect the coverage of the Limited
Warranty in any way, and you will continue to enjoy the full benefits of the Limited Warranty. If you keep this product and do
not opt out, then you accept all terms and conditions of the arbitration provision described above.
Conflict of Terms. In the event of a conflict or inconsistency between the terms of this Limited Warranty and the End User
License Agreement (“EULA”) in regards to dispute resolution, the terms of this Limited Warranty shall control and govern the
rights and obligations of the parties and shall take precedence over the EULA.
7
LIMITÉE GARANTIE
LG ELECTRONICS CANADA, INC.
GARANTIE LIMITÉE DES RÉFRIGÉRATEURS LG - Canada
8
9
10
TABLE OF CONTENTS
United States Warranty
English Version
Spanish Version
Canada Warranty
English Version
French Version
Important Safety Instructions
Requirements for Ground Connection
Parts and Features
Refrigerator Installation
Unpacking
Installation
How to remove and install Handle
How to remove and Install the
Refrigerator Doors
How to remove and Install Pull-Out Drawer
Closing and Aligning the doors
Using your Refrigerator
Ensuring Proper Air Circulation
Multi Flow
Ice Plus
Door Alarm
Adjusting the Controls
Food Storage Guide
Storing Frozen Food
Refrigerator Section
Refrigerator Shelves
Pantry
Crisper Humidity Control
Crisper cover with interior lattice
Door Racks
Dairy Compartment
Egg Compartment
Freezer Section
Ice Bin
DuraBase
Durabase Divider
Glide Out Drawer
Tilting Door
Door in Door
Door in Door Compartment
Door in Door Case
Door in Door Bins
Refrigerator Care and Cleaning
Refrigerator Cleaning
Outside
Inside Walls
Door Lining & Gaskets
Plastic Parts (Covers and Panel)
Back Cover
Replacing Refrigerator Lights
1-2
3-4
5-7
8-10
12-13
13
14
15-21
15
15
16
17-18
19-20
21
22-28
22
22
22
22
23
23
23-24
24-27
24-25
25
25
25
26
26
26
26
26
27
27
27
27
28
28
28
28
11
29-30
29
29
29
29
29
29
29
Replacing The Fresh Air Filter
Power Interruptions
When Going on Vacation
When Moving
29
29
29
29
About the Automatic Ice Maker
Connecting the Water Line
Troubleshooting Guide
Smart DiagnosisTM
31
32-34
35-37
38
IMPORTANT SAFETY INSTRUCTIONS
SAFETY MESSAGES
This manual contains several important safety notices. Always read and obey all of the following safety messages.
This is the safety alert symbol. This symbol is a warning to potential dangers that could cause death, injury
or damage to you, others or the product. All safety messages will follow after this warning symbol and the
word “DANGER”, “CAUTION” or “WARNING”. These words mean:
DANGER
You may be killed or suffer fatal damage if you do not follow instructions.
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury
or damage to the product.
All safety messages inform you of potential danger, advise you on how to reduce the risk of injury and tell you what
can occur if the instructions are not followed.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm.
WARNING
To reduce the risk of fire, electrical shock or personal injury, the following precaution measures should be
followed:
ţ If the use of this unit is no longer needed, please
ţ Immediately repair or replace all faulty or damaged
contact local authorities to dispose of this product in a
service cables. Do not use cords that have cracks or
safe way due contains Pentane-cycle or pentane like gas
abrasion damage on the length of the cord or on the
for insulation. Insulation gases require a special eliminaplug.
tion process. This product contains flammable insulaţ8IFONoving your refrigerator, take care not to roll
tion.
over the electrical cord.
ţ For your safety, this product should be properly
grounded. Have a qualified professional check the
ţ DO NOT store or use gasoline or other combustible
electrical circuit and outlet to ensure a proper ground
liquids or vapors in proximity with this or any other
connection.
electrical appliance.
ţ Read all instructions before utilizing the product. Utilize
ţ DO NOT permit children to climb, stand or swing from
this product only as explicitly expressed in this guide.
the doors or shelves of the refrigerator. This can cause
serious injury to them and damage to the product.
ţ Once the refrigerator is operating, avoid touching cold
surfaces of the freezer with damp or wet hands; the skin
ţ Keep your fingers away from areas in which they can
could become adhered to these surfaces.
become caught, such as the doors, hinges and cabinets.
Be careful closing the doors when children are near.
ţ In refrigerators with an automatic ice dispenser, avoid
contact with moving parts of the ejector mechanism or
ţ Unplug the refrigerator before cleaning or repairing.
with the heating mechanism that discharges the cubes.
NOTE: We strongly recommend that any repair services
DO NOT place your fingers or hands in the ice dispenser
be performed by a qualified professional.
mechanism while the refrigerator is connected.
ţ DO NOT store explosive substances such as aerosol
ţ DO NOT refreeze foods which have already thawed. The
cans with a flammable propellant in this appliance.
Department of Agriculture of the United States, in your
Bulletin of Home and Gardens No. 69 establishes that:
ţ If the use of this unit is no longer needed, please “...You can refreeze food that has thawed if they contain
contact local authorities to dispose of this product in a ice crystals or are cold and below 40 °F (4 °C)”.
safe way due contains
“...Ground beef, perishable food or seafood that is discol
Pentane-cycle or pentane like gas for insulation. Insula- ored or has an unpleasant odor should not be frozen or
tion gases require a special elimination process. This consumed. Consumption of melted ice cream should
also be avoided. If the odor or color of food is question
product contains flammable insulation.
able, discard it. The food may be dangerous to
consume”.
ţ Do not keep bottles in the freezer compartment, they
could explode after freezing and cause damage.
“Partial thawing or refreezing reduces the quality of the
food, especially fruit, vegetables and prepared meals.
The quality of red meat is less affected than other foods.
Use refrozen products as soon as possible in order to
maintain their quality”.
KEEP THESE INSTRUCTIONS
CAUTION
This appliance is not intended for use by children, persons with physical or mental disabilities, persons with reduced
sensory or mental capacity, or persons with lack of experience or know-how, unless they have supervision or instruction
in relation to the use of the appliance by the person responsible for their safety. Children should be supervised to
assure that they do not play with the appliance.
DANGER: CHILDREN MAY BECOME TRAPPED
BEFORE DISPOSING YOUR REFRIGERATOR
OR FREEZER WHEN NO LONGER IN USE:
ţ Remove the doors.
ţ Leave the shelves in place so that children
cannot easily become stuck in them.
Children becoming trapped or suffocated is not
a problem of the past. Discarded and abandoned
refrigerators are a hazard, even if they remain there
“for just a few days”. If you would like to dispose of
your old refrigerator, please follow the instructions
below to prevent any accidents.
CFC DISPOSAL
Your old refrigerator may have a cooling system that
uses CFC’s (chlorofluorocarbons). CFC affects the
stratospheric layer of the ozone.
If you decide to throw out your old refrigerator, ensure
that CFC contaminants are properly disposed of by a
qualified professional. If you intentionally remove the
CFC refrigerant, you could be subject to fines or prison
in accordance with environmental legislation in effect.
REQUIREMENTS FOR GROUND CONNECTION
IMPORTANT: Attentively read the following.
TO CONNECT ELECTRICITY
WARNING
ELECTRICAL SHOCK HAZARD
FOR YOUR PERSONAL SAFETY, this appliance must
be properly grounded. Have a qualified electrician
check your wall outlet to ensure that the plug is
grounded properly.
3 prong
grounding type
wall receptacle
3 prong
grounding
plug
Do not use an extension cable. It is your responsibility
and obligation to replace two-prong outlets with that of
an adequately grounded three-prong outlet.
Do not, under any circumstance, cut or extract the third
prong from the plug.
NOTE: Before installation, cleaning or replacing light
bulbs, you must disconnect the appliance from the
power source. When finished, plug the appliance back in
and adjust the thermostat to the desired position.
USE OF EXTENSION CABLES
We do not recommend the use of extension cables.
However, if you still choose to utilize an extension cable,
it is absolutely necessary that it is listed in the UL (in
the United States) or CSA (in Canada), that it supports
three-pronged plugs and that the electrical current
support a minimum of 15 A and 120 V.
The use of an extension cable will increase the amount
of space needed behind the refrigerator.
Ensure proper
ground exists
before use
WARNING
REPLACING ELECTRICAL CABLE
RECOMMENDED GROUNDING METHOD
If the power cord is damaged, it must be replaced by
our service center or qualified LG technician to avoid
any risk.
Your refrigerator must always be plugged to its own
outlet which is adequately grounded. The energy current
should only be 115 V, 60 Hz, A.C. and fused at 15 or 20
A. This provides the best performance and prevents an
overload which could cause a fire from the overheating
of the cables.
It is recommended that a separate circuit be used for
this appliance, as well as a receptacle that cannot be
disconnected with a switch.
WARNING: Do not use extension cords or adapters
ungrounded. Do not extend or modify the power power.
WARNING: NEVER disconnect the refrigerator by
pulling the power cord, always grip the plug firmly and
disconnect it directly from the outlet.
PARTS AND FEATURES
A
L
N
B
M
C
D
E
O
F
K
G
J
H
I
Read this section to familiarize yourself with the parts and features of your new refrigerator.
NOTE: This guide covers different models. Your refrigerator could have some or all of the features and parts listed
below. The location of some of the parts may not correspond to that of your model.
A Refrigerator Temperature Control
I
B Refrigerator Light
J Pull Out Drawer
C Shelves
K Freezer Light
D Optibin Crisper
L Air Filter
Keeps fruits and vegetable fresh and crisp
E
Pantry *
The Air Filter helps remove odors from
the refrigerator.
M Cheese & Butter Bin
It makes spreading butter and slicing cheese easier.
F Ice Maker *
G Ice Bin*
H Durabase
Durabase divider
N Door-In-Door Case
O Condiment Bin
* On some models
REFRIGERATOR INSTALLATION
WARNING
EXCESSIVE WEIGHT HAZARD
Use the assistance of two or more persons to move or
install the refrigerator. Not following these instructions
may cause injury to the back and other parts of the
body.
3. Install the refrigerator in an area between 55 °F
(13 °C) and 110 °F (43 °C). If the surrounding temperature
is lower or higher than previously mentioned, it can
adversely affect the unit.
CAUTION: Avoid placing the unit near heat
sources, direct sunlight or humidity.
UNPACKING
Before installing your refrigerator, remove any tape or
temporary stickers. Please remove vinyl from doors
before connecting unit to the electrical supply (on some
models). Do not remove any stickers that feature
warnings, the model serial number or the technical label
of the product located on the back of the refrigerator.
To remove adhesive tape residue, rub it well with your
fingers and a little liquid detergent. Clean with warm
water and let dry.
Do not use sharp instruments, rubbing alcohol, flammable
liquids or abrasive cleaning products to remove the
adhesive tape or glue. These products can damage the
surface of your refrigerator. For more information, see
the section on “Important Safety Instructions”.
The shelves come already installed in their factory
position. Remove the shelves and replace them
according to your spacing needs.
Moving Your Refrigerator:
Your refrigerator is extremely heavy. Make sure you
protect the floor when moving your refrigerator for
cleaning or servicing. Always pull your refrigerator
straight out when moving it. Do not shift from side
to side or “walk” the refrigerator when attempting to
move it as this can cause damage to the floor.
WARNING
EXPLOSION HAZARD
Keep all flammable materials and vapors (such as
gasoline) away from the refrigerator. Not following
these instructions may cause death, explosion or fire
INSTALLATION
1. Avoid placing the unit near heat sources, direct
sunlight, or humidity.
2. To avoid vibration, the unit should be leveled. If needed,
adjust the leveling screws to compensate for an
unleveled floor. The front should be slightly taller than
the rear to ensure that the doors close properly. The
leveling screws can easily be turned by slightly tilting
the front of the refrigerator, turning the leveling screws
clockwise (
) to raise it and counter-clockwise
(
) to lower it.
ONCE INSTALLED
1. Carefully clean your refrigerator and remove and dust
accumulated during shipping.
2. Install accessories such as the ice bin, door racks,
shelves, etc., in their proper places. These are already
packed to prevent any possible damage during
shipping.
3. Leave your refrigerator on for 2 to 3 hours before
storing food inside. Verify that there is a flow of cold air
in the freezer compartment to ensure proper cooling.
Your refrigerator is now ready for use.
WARNING:
ţTake care when working with the hinges, base cover
and stops, etc. You may injure yourself.
ţDO not place your hands or any tools in the air vents,
the base cover or in the bottom of the refrigerator. This
may cause injury or electrical shock.
ONCE INSTALLED
Carefully clean your refrigerator and remove and dust
NOTE
This appliance is intended to be used in household and
similar applications such as:
ţStaff kitchen areas in shops, offices and other working
environments;
ţFarm houses and by clients in hotels, motels and other
residential type environments;
ţBed and breakfast type environments;
ţCatering and similar non-retail applications.
ţThe refrigerator should be level and on a firm ground.
Keep a Proper Distance from Adjacent
Objects
Please keep the refrigerator at an
adequate distance from other objects.
Insufficient spacing can reduce the
refrigerator’s freezing efficiency and
increase electricity consumption.
(5.08 cm) 2”
REFRIGERATOR INSTALLATION
TOOLS YOU MAY NEED
10 mm
1/4 in
3/8 in
Hex Socket Wrench Phillips Screwdriver
Flat Head Screwdriver
1/4 in
3/32 in
Allen Wrench
NOTE: It is always recommended that the doors be removed when it is necessary to move the refrigerator through a
narrow opening. If it is necessary to remove the handles follow the directions below.
NOTE: Handle appearance may vary from illustrations on this page.
DOOR HANDLE INSTALLATION
1. Reinstalling Refrigerator Handle
Place the handle on the door by aligning handle
footprints to fit mounting fasteners and tighten
the set screws with a 3/32“ Allen wrench.
NOTE: If the handle mounting fasteners need to
be tightened or removed, use a 1/4 ” Allen wrench.
DOOR HANDLE REMOVING
1. Removing Refrigerator Handle
Loosen the set screws with the 3/32 ” Allen wrench
and remove the handle.
NOTE: If the handle mounting fasteners need to be
tightened or removed, use a 1/4 ” Allen wrench.
Mounting
Fasteners
Set Screw
Mounting
Fasteners
Allen Wrench
2. Reinstalling Freezer Drawer Handle
Place the handle on the door by aligning handle
footprints to fit mounting fasteners and tighten
the set screws on the bottom of the handle with
a 3/32” Allen wrench.
2. Removing Freezer Drawer Handle
Loosen the set screws located on the lower side of
the handle with the 3/32” Allen wrench and remove
the handle.
NOTE: If the handle mounting fasteners need to
be tightened or removed, use a 1/4 ” Allen wrench.
NOTE: If the handle mounting fasteners need to be
tightened or removed, use a 1/4 ” Allen wrench.
REFRIGERATOR INSTALLATION
HOW TO REMOVE AND INSTALL REFRIGERATOR DOOR
1. Removing Refrigerator Doors
NOTE: Handle, top hinge and hinge cover appearance may vary from illustrations on this page.
WARNING
ţ Disconnect electrical supply to the refrigerator before installing. Failure to do so could result in death or serious
injury.
ţ Do not put hands or feet or metal sticks into the air vents, base grille, or bottom of the refrigerator. You may be
injured or receive an electrical shock.
ţ Be careful when you work with the hinge, base grille, and stopper. You may be injured.
; Left Door
ţ Open the door. Remove the top hinge cover screw (1 ).
ţ Use a flat blade screwdriver to lift the tabs on the front underside of the cover(2). Lift up the cover.
ţ Disconnect all wire harness (3).
ţ Remove the grounding screw(4).
ţ Rotate hinge lever (5) counterclockwise. Lift the top hinge (6) free of the hinge lever latch (7).
ţ Place the door on a non-scratching surface with the inside up.
; Right Door
ţ Open the door. Remove the top hinge cover screw (8).
ţ Use a flat blade screwdriver to lift the tabs on the front underside of the cover (9). Lift up the cover.
ţ Rotate hinge lever (10) clockwise. Lift the top hinge (11) free of the hinge lever latch (12).
ţ Place the door on a non-scratching surface with the inside up.
CAUTION: When lifting the hinge free of the latch, be careful that the door does not fall forward.
ţ Lift the door from the middle hinge pin and remove the door.
ţ Place the door, inside facing up, on a nonscratching surface.
(2)
(1)
(9)
(8)
(10)
(3)
(5)
(11)
(12)
(4)
(6)
(7)
REFRIGERATOR INSTALLATION
; Left Door
ţ Lower the door onto the middle hinge pin (7).
ţ Make sure the door is aligned with the cabinet.
ţ Fit the top hinge (8) over the hinge lever latch (9)
and into place. Rotate the lever (10) clockwise to
secure the hinge.
ţ Install the grounding screw (11) and connect all the
wire harnesses (12).
ţ Hook the tab on the door-switch side of the cover
(13) under the edge of the wire opening in the cabinet top.
ţ Position the cover into place.
ţ Insert and tighten the cover screw (14).
HOW TO REMOVE AND INSTALL
REFRIGERATOR DOOR (CONT.)
2. Refrigerator Door Reinstallation
Install the right-side door first.
; Right Door
ţ Lower the door onto the middle hinge pin (1).
ţ Make sure the door is aligned with the cabinet.
ţ Fit the top hinge (2) over the hinge lever latch (3)
and into place. Rotate the lever (4) counterclockwise
to secure the hinge.
ţ Hook the tab on the door-switch side of the cover
(5) under the edge of the wire opening in the cabinet
top.
ţ Position the cover into place.
ţ Insert and tighten the cover screw (6).
1
7
(14)
(13)
(5)
(6)
(4)
(3)
(9)
(11)
(2)
(12)
(8)
(10)
REFRIGERATOR INSTALLATION
HOW TO REMOVE AND INSTALL THE PULL
OUT DRAWER
Fig. 4
Door
supports
Rail tabes
1. Removing Pull out Drawer
IMPORTANT: To avoid possible injury, product or
property damage, you will need two persons to
perform the following instructions.
ţ Pull the drawer open to full lower extension.
Remove the durabase by lifting it from rail system.
(Fig. 1)
ţ Push the rails back into drawer cavity. With both
hands, hold the center of the bar and push it in
so that both rails go back simultaneously. (Fig.5)
(Fig. 6)
Fig. 1
Durabase
Fig. 5
ţ Remove the screws of the rail on both sides.
(Fig. 2)
Fig. 2
Fig. 6
screw
CAUTION: When removing drawer door, do not
hold it by the handle. The door could fall down
and you may be injured. Grasp the door with both
hands as pictured below when removing.
CAUTION: When laying down the drawer, be
careful not to damage the floor or hurt your feet
with the sharp edges on hinge side.
ţ With both hands, hold both sides of the door
(Fig. 3) and pull it up to separate it from the rails.
(Fig. 4)
Fig. 3
1
REFRIGERATOR INSTALLATION
HOW TO REMOVE AND INSTALL THE PULL OUT
DRAWER (CONT.)
2. Installing Pull out Drawer
ţ Lower door into final position and tighten the
screws. (Fig. 9)
Fig. 9
Screws
IMPORTANT: To avoid possible injury, product or
property damage, you will need two people to perform the following instructions.
ţ With both hands, hold the center of the bar and
pull it out to let both rails out to full extension
simultaneously. (Fig. 7)
Fig. 7
ţ With the rails pulled out to full extension, insert
the durabase in the rail assembly. (Fig. 10)
Fig. 10
Durabase
ţ Hook door supports into rail tabs. (Fig. 8)
Fig. 8
Door Supports
WARNING: To prevent accidental child and pet
entrapment or suffocation risk, DO NOT allow them
to play inside of drawer.
Rail tabes
WARNING: DO NOT step or sit down on Freezer
Drawer.
REFRIGERATOR INSTALLATION
CLOSING AND ALIGNING THE DOORS
Closing the Doors
Your refrigerator has two front leveling screws, one on
the right and one on the left. If your refrigerator seems
unstable or if you would like the doors to close more
easily, simply adjust the inclination of the refrigerator by
following the instructions below:
Door Alignment
The left refrigerator door has an adjustable nut, located
on the bottom hinge, to raise and lower, the door for
proper alignment.
If the space between your doors is uneven, follow the
instructions below to align the doors evenly:
Use the wrench (included with the Use & Care Guide) to
turn the nutin the door hinge to adjust the height. To the
right to raise or to the left to lower the heignt.
1. Plug the refrigerator into a 3 prong grounded outlet.
Move the refrigerator into its final position.
2. Use a flat head screwdriver to adjust the leveling screws,
turning clockwise to raise the side of the refrigerator
and counter-clockwise to lower it. It may take several
turns to adjust it to the inclination you would like.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws.
This will make it easier to adjust the screws.
The right refrigerator door does not have an adjustable
nut.
If the space between your doors is uneven, follow the
instructions below to align the right door:
1. With one hand, lift up both the inner and outer door
sections of the right door to raise them at the
middle hinge. (Opening the door may make lifting
easier).
2. With the other hand, use pliers to insert the snap
ring on the middle hinge of tjhe inner door section
as shown. Do not insert the ring on the hinge of the
outer door section.
3. Insert additional snap rings until the rignt door is
aligned. (Two snap rings are provided with the unit).
When moving your refrigerator
Note: Your refrigerator is extremely
heavy. When moving the refrigerator
for installing, cleaning or service be
sure to follow the next instructions.
1. Adjust leveling legs up.
2. Cover the floor with cardboard or hardboard to
avoid floor damage.
3. Always pull or push the refrigerator straight out
when moving it. Do not wiggle or “walk” the
refrigerator when trying to move it, as floor damage
could occur.
3. Open both doors again and check to make sure that
they close easily. If not, slightly tilt the refrigerator
further back by turning both leveling screws clockwise.
It may take several more turns. Make sure that you turn
both leveling screws the same amount.
4. Ensure that the refrigerator is even by using a level.
5. Replace the base grille.
NOTE: Your new refrigerator is uniquely designed with
two fresh food doors. Either door can be opened or
closed independently of one another. You may have
to exert slight pressure on doors to get them to close
completely.
1
USING YOUR REFRIGERATOR
ENSURING PROPER AIR CIRCULATION
CAUTION WHEN CLOSING THE DOOR
In order to obtain stable temperature, the air must flow
between the freezer and refrigerator sections. As shown
in the illustration below, the cold air enters through
the bottom part and circulates upward. This air returns
below the freezer floor and the rest of the air enters the
refrigerator section through the top vent.
MULTI FLOW
ţ The cooling fan operates more powerful and effective
than when in normal operation. This is especially
noticeable when new food is placed in the refrigerator
compartment.
ţ If the lining is damaged, water or other substances
could enter through the cool air vent causing
decreased efficiency.
CAUTION
To reduce the risk of door scratches, please make
sure that the refrigerator door mullion is always folded
ADJUSTING THE CONTROLS
Your refrigerator has two controls that allow you to
regulate the temperature the freezer and refrigerator
compartments.
Initially set the REFRIGERATOR CONTROL at 37°
degrees F and the FREEZER CONTROL at 0° degrees
F. Leave them at these setting for 24 hours (one day) to
stabilize. Then adjust the compartment temperature as
illustrated above.
B
J
Do not block any of these vents with packages of food.
This can interrupt the flow of air and cause temperature
and moisture problems.
IMPORTANT: Because air circulates between both
sections, any odors formed in one section will transfer
to the other. You must thoroughly clean both sections to
eliminate odors. To prevent odor transfer and drying out
of food, make sure you wrap or cover foods tightly (See
the “Food Storage Guide” section for details).
ICE PLUS
Press the button ICE PLUS. The LED light will turn on.
This function will remain activated for 24 hours and
intensify the cooling speed of the freezer and increase
ice production.
ţRefrigerator Control: 32 °F to 47 °F (0 °C to 8 °C)
To adjust the temperature in the refrigerator compartment
open both doors, then press the REFRIGERATOR button
to cycle through the range of available settings.
ţFreezer Control: -6°F to 9 ° F ( - 21°C to -13°C)
To adjust the temperature in the freezer compartment
open both doors, then press the FREEZER button to
cycle through the range of available settings.
ţ Temperature Display
To change the temperature display from Fahrenheit to
Celsius:
1. Simultaneously press and hold the FREEZER and
REFRIGERATOR buttons for more than 5 seconds.
2. Do the same to convert back to Fahrenheit.
DOOR ALARM
With this feature you will hear an alarm when the freezer
or refrigerator door is open for more than 1 minute.
These tones will repeat every 30 seconds. The alarm is
cancelled when the door is properly shut. To activate or
deactivate Door Alarm, press the button ALARM.
USING YOUR REFRIGERATOR
ADJUSTING CONTROL SETTINGS
FOOD STORAGE GUIDE
Give the refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before adding
food to the refrigerator. The mid-settings indicated in the
previous section should be correct for normal household
refrigerator usage. The controls are set correctly when
milk or juice is cold to your liking and ice cream is firm.
ITEMS
Storing Fresh Food Wrap or store food in the
refrigerator in airtight and
moisture-proof material unless
otherwise noted. This prevents
food odor and taste transfer
throughout the refrigerator. For
dated products, check date code
to ensure freshness.
The refrigerator control functions as the thermostat for
the entire appliance. The higher the number setting, the
longer the compressor will run to keep the temperature
colder. The freezer control adjusts the cold air flow from
the freezer to the refrigerator. Setting the freezer control
to a lower temperature keeps more cold air in the freezer
compartment to make it colder.
If you need to adjust the temperature in the refrigerator
or freezer, begin by adjusting the refrigerator first. Wait
24 hours after the refrigerator adjustment to check the
freezer temperature. If it is too warm or too cold, then
adjust the freezer control as well.
Use the settings listed in the table below as a guide.
CONDITION/REASON:
RECOMMENDED
ADJUSTMENT:
REFRIGERATOR section
is too warm
ţOpening the door often
ţAdding a large amount
of food
ţRoom temperature is
very warm
Adjust the
REFRIGERATOR setting
to the next highest
number and wait 24
hours, then check.
FREEZER section is too
warm/ ice is made too
slowly
ţOpening the door often
ţAdding a large amount
of food
ţRoom temperature is
very low (not cycling
often enough)
ţUsing ice frequently
ţAir vents blocked by
objects
Adjust the FREEZER
setting to the next
highest number and wait
24 hours, then check.
REFRIGERATOR section
is too cold
ţControls not set
correctly for your
conditions
Adjust the
REFRIGERATOR setting
to the next lowest
number and wait 24
hours, then check.
FREEZER section is too
cold
ţControls not set
correctly for your
conditions
Adjust the FREEZER
setting to the next lowest
number and wait 24
hours, then check.
HOW TO STORE
Remove any objects
blocking air flow.
Butter or
margarine
Store opened butter in a covered
dish or in a closed compartment.
When storing a larger quantity,
wrap in freezer packing and
freeze.
Cheese
Store in original packaging until
you are ready to use it. Once
opened, tightly rewrap with
plastic wrap or aluminum foil.
Vegetables with
skins (carrots,
peppers)
Place in bags or plastic containers
inside the crisper.
Fruit
Wash and let dry; store in plastic
bags in the refrigerator. Do not
wash or pit berries until you
are ready to eat them. Berries
should be selected and kept in
their original packaging (if there
is any) or in a paper bag closed
halfway and set on a shelf.
Leafy Vegetables
Remove original packaging and
trim any dirty or discolored parts.
Wash in cold water and drain.
Place in a plastic bag or plastic
container and store in the crisper.
Fish
Consume fish or seafood the
same day purchased.
Chef Fresh
Store any meat in original airtight,
moisture-proof
packaging
Rewrap if necessary.
Leftovers
Cover leftovers with plastic
wrap or aluminum foil. Plastic
containers with airtight lids can
also be used.
STORING FROZEN FOOD
NOTE: For more information on how to prepare food to
be frozen such in a way to see the period they can be
stored consult a frozen food guide or cook book.
Packaging
A great freezing depends on how great you package the
food. When you seal the package make sure you remove
all excess air and do not allow humidity. A package that
is incorrectly sealed will result in the transmission of bad
odors, contaminants inside your refrigerator and will
cause your foods to dry.
USING YOUR REFRIGERATOR
Packaging Recommendations:
ţ UsFseBMFEQMBsUJDcontainers.
ţ UsFQMBsUJDcontainersXJUIBTNPoUIsurface.
ţ PackageXJUIBMVNJOVNfPJMoGIJHIresistance.
ţ WrBQXJUIQBQFSMByeredXJUIQMBstic.
ţ UsewatFSQrooGQMBstic.
ţ UsFrecPNNFOEFEQMBsUJDCBHTtPstorefrozenfoods.
REFRIGERATOR SECTION
REFRIGERATOR SHELVES
FollowtheseQBDLBHJOHorcontainerinstructionsinorder
tPreBDIUIFCestfreezing
The shelving of your refrigerator can CF adjusted tP
cPNQMZ with your storage necessities; %FQFOEJOH PO
the NPEFM you have in can include glass shelving PS
wired shelving.The storing of your foods together BOE
adjusting the shelving to different heights will ease tP
IFMQ you locate what you need. This also IFMQT yPVS
refrigeratortostayshutlongerwhichwillsaveyouenergy.
Do not use:
ţ Bread8rBQQJOH
ţ PlasUJDcPOUBJOFSOoUsafefPSstoring.
ţ ContainersXJUIPVUMJETPSseals.
ţ WaxFEQBQFSPSwaxFEQMBstic.
ţ ThinwrBQQJOHQBQFSPSOotwatFSQroof.
IMPORTANT:Whileyour refrigerator glass shelving arF
cold do not clean with hot or wBSN water. The glasT
shelving NBZ Creak if FYQosed to rBQJE tFNQFraturF
changes or hard JNQBDts. For your safety the glasT
shelving are NBEF out of tFNQFred glass so when aU
CreBLJOHUIFZwillfracturFJOtPUJOZfrBHNFOts.
Freezing
NOTE:BecarefulwhileNovingorrelocatingtheshelveT
theyareheavy.IfNovingtheshelvesisrequiredkFFQJO
NJOE to locate UIFN in a safe envirPONFOU to QrevFOU
UIFNfrPNCreaking.
IMPORTANT:%POoUkFFQCottleTJOUIFfreezFS
cPNQBrUNFOtUIFZNBZFYQMPEFBGterfree[JOHBOE
causFEBNBHF
FortheNaYJNVNuseofyourfreezerdonotstoreexcesT
food.%PnotintroducealargeBNPVOUofunfrozenfPPET
that cannot CF frozen within 24 hours (no NPre UIBO
2 – 3 QPVOET or ,91 kg - 1,36 kg of food QFS squarF
inchofTQBceinthefreezer).SufficientTQBceNVstCF
leftinorderfortheairtocirculateQrPQFSMZaroundUIF
QBDLBHes. Leave enough TQBce in order to close yPVS
refrigeratorXJUIPVUEJGżDVMty.
Adjusting Shelves
RFNovetheshelvesandadjustUIFNtoyourconvenience.
ţRemoving Shelves
InclinethefrontoftheshelfinthedirectionindicatedCZ
figure1andliftinthedirectionindicatedCyfigure2.PVMM
UIFTIFMGtowardsZPV
1
Storage UJNes can vary EFQFOEJOH on the tZQF BOE
quality of the food, the way its QBDLBHF or QBDLBHJOH
containerused,(inDPNQBSJsontoairandIVNJEJty),BOE
the tFNQFrature it CFJOH stored in. Ice crystalsfPSNFE
insideyourQBDLBHFareOPSNBMitindicatestheairBOE
IVNJEJtZJOTJEFZPVSQBDLBHFIavFcondensed.
2
NOTE: Let wBSN foods cool off at rPPN tFNQFraturF
for BQQroYJNately 30 NJO then wrBQ accordingly XJUI
theNethodsNFOUJPOBCoveandfreeze.BylettingyPVS
wBSNfoodscooloffCFforeyouintroduceUIFNtoyPVS
freezFSJUXJMMsaveZPVFOFrgy.
WARNING
ţ Replacing Shelves
Incline the frontal QBrt of the shelf (1) and guide UIF
shelfhookstowardsthePQFOJOHTattheheightdesirFE
Thenlowerthefrontoftheshelf(2)sothehookscanCF
insertFE(
JOUIFTIFMGsVQQPrtT
1
SUFFOCATING DANGER
Adequate ventilation is required when using dry icF
%ryiceis$BSCPO%Joxide(CO2).WheniteWBQPratesJU
Qroducesoxygen,causingdizziness,slightheadacheT
unconsciousnessordeath.%PnotinhaletheseWBQPrT
BOEQrPQFSMZventilatFUIFrPPNwhileZPVVsFErZJcF
3
2
NOTE: Make sure that the shelf is installed in UIF
horizontalNBOOFr.Otherwise,itcancausetheshelveTUP
fall,whichXJMMcauseyPVSstoredfPPEtPTQJMM
USING YOUR REFRIGERATOR
Sliding Shelves (in some models)
You can slide some of the shelves in your refrigerator
towards inside or outside like explained below.
ţTo slide the shelf towards the outside: Pull towards you,
figure A.
ţTo slide the shelf towards the inside: Push until it stops,
figure B.
CRISPER HUMIDITY CONTROL (in some models)
You can control the amount of humidity in the moisturesealed crispers. Adjust the control to any setting between
HIGH and LOW.
ţ“High”: keeps moist air in the crisper for best storage
of vegetables.
ţ“Low”: lets moist air out of the crisper for best storage
of fruits.
I I
I I
Figure A
I
Figure B
In order to remove a shelf from a metal frame
ţPull the shelf until it stops.
ţIncline the front of the shelf towards the top and pull
forward.
ţLift the shelf in the manner it moves across the
support openings.
To put back into place just reverse these steps.
I
I
To remove the crisper:
ţSlide crisper straight out to the stop.
ţLift the front of the crisper, then pull it out to remove
ţReplace the crisper by sliding it back in fully past the
drawer stop.
Functional Shelves (Folding Shelves, in some models)
You can store tall articles like gallons or bottles just by
simply folding the shelf in half.
CAUTION: Be careful when you handle the glass
cover because it could loose.
To remove the glass:
ţLift up the glass after inserting a screwdriver under the
crisper cover.
ţPull glass cover up and out.
PANTRY (in some models)
For storage of meat or fresh food. Adjust the control to
desired temperature by moving from COLD to COLDER.
Pull forward to open. Lift slightly and pull it out to remove.
To remove the crisper cover support:
NOTE: Remove glass before removing the crisper cover
support.
ţWhile holding the crisper cover support with both
hands (as shown in the image below). Pull forward and
slightly lift the front part.
USING YOUR REFRIGERATOR
DOOR RACKS
FREEZER SECTION
The door racks are removable for easy cleaning and
adjusting.
ţ To remove the rack, simply lift the rack up and pull
straight out (1).
ţ To replace the rack, slide it in above the desired
support button and push down until it stops (2).
1
ICE BIN (In some models)
ţPull the drawer as much as possible (1).
ţRaise the ice box and take it out carefully (2).
ţTake the drawer off as much as possible and put the
ice bin in the right position (3).
2
Drawer
2
1
Ice Bin
WARNING: Somebody can be hurt if door racks
are not firmly assembled.
CAUTION: DO NOT allow children to play with
baskets. Sharp corners on baskets could cause
injury.
3
NOTE: DO NOT adjust a rack that is loaded with food.
DAIRY COMPARTMENT(in some models)
ţ To remove the dairy compartment, simply lift it and
pull straight out (1).
ţ To replace the dairy compartment, slide it in above the
desired location and push down until it stops (2).
1
2
EGG COMPARTMENT (in some models)
Keep the eggs compartment in an interior shelf, not in
a door rack.
CAUTION: Do not use the
eggs compartment as a
container for keeping ice in
the freezer compartment. If it
freezes, it could break easily.
2
USING YOUR REFRIGERATOR
GLIDE-OUT DRAWER BASKET (in some models)
DURABASE (in some models)
ţTorFNovFUIFDurBCBTFQVTI
JU CBDL rBJTF UIF frPOU QBrU
BOEQVMMJUVQ(1).
ţTo QVU JU CBDL JOTFrU UIF
DurBCBTFJOUIFrBJMBTTFNCMZ
(2).
ţ PVMMUIFCoYBTNVDIBT
QoTTJCMFQJDLVQUIFCBTLFU
BCJU(
BOEQVMMJUPVU(
1
1
2
ţ ToJOTUBMMQVMMUIFDorETUP
UIFJS fullFTU (1). LPDL UIF
TVQQPrUT of UIF CBTLFU
JOUoUIFTMJEFTofUIFDorET
(2)BOEQVTIJUBMMUIFwBZ
UIrPVHI(
DURABASE DIVIDER (in some models)
AlloXT orHBOJ[JOH UIF DurBCBTF
BrFBJOTFDUJPOT
ForNoWJOHUIFEJWJEFrjuTUNovF
JUJOUIFEJrFDUJPOUIBUZouwBOU.
WARNING:5IFrFJTFOPVHI
TQBDFforUIFDIJMErFOUoQMBZ.
1
2
3
WARNING: *O orEFS UP
QrFvFOUBDDJEFOUTTVDIBTTuffoDBUJPODONOTlFU
DIJMErFOBOEQFUTQMBZJOTJEFUIFEVrBCBTF
TILTING DOOR (in some models)
5IF UJMUJOH EPPS QroWJEFT BO
FBTZBDDFTTUoUIFfrozFOfPPE
How to use:
*ODMJOF UIF EPPS EoXOwBrET
BOEQVMMJUPVU.
WARNING:#FDBrFfulXIFOPQFOJOHUIFEPPrEP
OoU QMBDF Zour fFFU VOEFS UIF EPPS or Zour IBOET
JOTJEFUIFfrFFzFr;ZPVNBZIVrUUIFNJOEPJOHTo
2
2
USING YOUR REFRIGERATOR
DOOR-IN-DOOR
1. To remove the Door-In-Door Case, lift up and
pull out.
The Door-In-Door compartment allows for easy
access of commonly used food items.
The outer Door-In-Door door includes two door
bins, the Cheese & Butter and Condiment bins,
that are specially designed for food this makes
spreading butter and slicing cheese easier.
The Cheese & Butter and Condiment
bins are not recommended for storing
items that spoil easily such as milk and
mayonnaise.
2. To replace the Door-In-Door case, line the tabs
on the Door-In-Door Case with the slots on the
door and push down until it snaps into place.
DOOR-IN-DOOR COMPARTMENT
To access the Door-In-Door compartment,
lightly press the button on the right refrigerator
door handle to open the door.
DOOR-IN-DOOR BINS
The Door-In-Door inner and outer door bins are
removable for easy cleaning.
There is no need to grip the
handle when opening the
Door-In-Door door.
If the handle is gripped
when the button is pressed
you may hear a clicking
noise. This is normal.
1. To remove the door bins, lift up and pull out.
2. To replace the door bins, slide the door bin in
above the desired support and push down until
it snaps into place.
DOOR-IN-DOOR CASE
To open the Door-In-Door Case, slightly push
the marked area to pop it open. The Door-InDoor Case is removable for easy cleaning and
adjusment.
DOOR-IN-DOOR LOWER BINS
The Door-In-Door lower shelf is removable for
easy cleaning.
1. After removing Door-in-Door Case.
2. To remove the Lower Bin, lift up and pull out.
2
REFRIGERATOR CARE AND CLEANING
BACK COVER
WARNING
WARNING
EXPLOSION HAZARD
ELECTRICAL SHOCK HAZARD
Before you begin, either unplug the refrigerator or turn
off power at the circuit breaker or fuse box.
Do not use flammable cleaners. Not following these
instructions can cause death, explosion or fire.
NOTE: Back Cover should only
be removed by a qualified
technician.
The refrigerator, as well as the freezer, do their own
de-freezing. This process does not prevent the build
up of contaminants, therefore it is suggested that you
clean both parts once a month; clean spilled liquids
immediately.
In order to get an efficient
performance of your refrigerator,
clean the back cover of it at least
twice a year.
BACK
COVER
REPLACING REFRIGERATOR LIGHTS
REFRIGERATOR CLEANING
ţUnplug your refrigerator.
ţPull out all of the removable parts (such as the
vegetable and dairy doors).
ţUse a clean sponge (or a soft rag) and use it with
lukewarm water mixed with detergent. Do not use
abrasive or concentrated cleaners.
ţHand wash it, and dry it thoroughly.
ţPlug the refrigerator back in.
NOTE: The interior lighting for refrigerator uses LED
lighting.
DO NOT try to change any LED module. LED lighting
should only be replaced by a qualified service technician.
REPLACING THE FRESH AIR FILTER
It recommended that you replace the air filter:
Aproximately every six months.
When the CHANGE FILTER lights turns on.
OUTSIDE
Wax the outside in order to create better protection. Make
sure you use a product specifically design to be used
for electro-domestic products (car wax is acceptable).
Use a clean, soft rag, and perform this task twice a year.
For metal-made refrigerators, do not wax, simply clean
it with water and detergent. Do not use concentrated or
abrasive products.
1. Remove the Old Filter
Turn the filter cover to the left to detach from the
refrigerator wall. The filter is located on the inside of the
filter cover. Remove the filter from the cover and
replace it with a new filter.
NOTE: Avoid the usage of chemical products that
contain phosphates or bleach.
INSIDE (Allow freezer to slightly warm up a small
degree to prevent cloth from sticking)
In order to eliminate bad odors, clean the inside of
the refrigerator with a mixture of baking powder and
lukewarm water (one teaspoon of baking powder per cup
of water). Ensure that the powder dissolves thoroughly, in
order to prevent any sort of damage.
2.Install a New Air Filter.
Place the new filter inside of the cover with the side that
says “Front” facing outward. Turn the filter cover to the
right to attach to the refrigerator wall.
DOOR LINING AND GASKETS
Use only a mild detergent (such as dish soap).
PLASTIC PARTS (Covers and Panels)
Do not use abrasive, paper or rough products. These
could damage the product.
2
After changing the filter, push and hold the Air Filter
button for three seconds to reset the filter sensor.
REFRIGERATOR CARE AND CLEANING
POWER INTERRUPTIONS
WHEN MOVING
1.
If you decide to take your refrigerator with you when
moving, consider the following:
2.
3.
ţ
ţ
ţ
In case of a black out, call your electric company
and ask how long it will last.
In case of a 24 hour or less black out, do not open
the refrigerator; this will keep the food fresh.
In case of a longer black out, do one of the following
options:
Pull out all of the frozen food and keep them in an
ice chest.
Put 2 lbs (907 g) of frozen ice (make sure you use
gloves) for each square foot (28 L) inside the freezer.
This task will preserve the food for 2 to 4 days.
In case you do not possess neither ice chest or dry
ice, consume your food as soon as possible.
REMEMBER: In a power failure, a full freezer stays cold
longer than a partially filled one. A freezer full of meat
stays cold longer than a freezer full of baked goods. If
you see that food contains ice crystals, it may be safely
refrozen, although the quality and flavor may be affected.
If the condition of the food is poor or if you feel it unsafe,
dispose of it.
1. Remove all of the food from it, and place the frozen
food in an ice chest with dry ice.
2. Unplug your refrigerator.
3. Empty the water from its tray.
4. Clean and dry it with a rag.
5. Pull out all of the removable parts, and wrap them with
adhesive tape.
6. Depending on the model of the refrigerator, lift the top
part of the refrigerator so it can roll with ease, or screw
the levelers so it won´t scratch the floor. Consult to the
section “Closing and Aligning Doors”.
7. Keep the doors closed with the cable glued to the
refrigerator cabinet with an adhesive tape.
When your refrigerator arrives to your home, put
everything back into place and read the section
“Refrigerator Installation” in order to obtain installation
preparation. In case your refrigerator has a factory ice
maker, remember you have to reconnect the water
supply.
WHEN GOING ON VACATION
If you decide to leave your refrigerator on when going
away, consider these steps:
1. Consume all of the perishable items and freeze the
rest.
2. Empty the ice bin.
If you decide to leave your refrigerator off:
1. Remove all of the food.
2. Unplug your refrigerator.
3. Clean and dry it well.
4. Make sure the doors stay open (use blocks or tape) in
order to prevent bad odors and fungi from happening.
ABOUT THE AUTOMATIC ICE MAKER
NOTE: The automatic Ice maker is only included in some
models. Check your specifications of your refrigerator.
YOU MUST TURN THE SWITCH TO O (OFF)
ţ When the water supply is interrupted for many hours.
ţ When the ice container is left out of its place for more
than one or two minutes.
ţ When the refrigerator will not be in use for various
days.
WARNING
PERSONAL INJURY HAZARD
Avoid contact with any moving parts of the ejector
mechanism or with the heater that releases the ice
cubes. DO NOT place your fingers in the automatic ice
maker when the refrigerator is plugged in.
NORMAL SOUNDS
ţ The valve will emit a buzzing sound when the ice maker
is full of water. If the switch is placed in the off position
the buzz will still be heard even when the water pipe
has not been connected. To avoid this sound, move
switch to O (off) position.
OPERATING INSTRUCTIONS
After turning on your refrigerator, the ice will start to be
made between 12 and 24 hours.
NOTE: The ice maker can get damaged if the switch is
kept in the ON position before the water pipe has been
connected.
ţ While the ice maker is filling up with water and
producing ice, you will hear the sound of the ice falling
and water flowing through the pipes.
PREPARING FOR VACATIONS
Ice maker
Move the ice maker switch to the O (off) position and cut
the flow of water going into the refrigerator.
Switch
Sensor
If room temperature is at freezing point, have a
specialized technician drain the flow of water from the
inner pipes (certain models) to avoid broken pipe related
damage.
The ice maker produces 12 cubes per cycle (in between
80 and 100 cubes in a 24 hour period), depending on
the temperature of the freezer, the times in which the
door opens, and other using conditions (amount of food
in the freezer, etc).
NOTE: It is necessary to have a water source when both
water and/or Ice dispensers are available in your product.
If the refrigerator is used before the connection of water
to the ice maker was performed, you must turn its dial
to O (off).
When the water connections are performed, turn its dial
to I (on).
The ice maker will fill up (and start making ice) between
12 and 24 hours after the refrigerator is turned on.
Throw away the first batch of ice. Make sure that nothing
interferes with the sensor.
When the ice reaches the sensor, the ice maker will stop
to make ice immediately.
It’s normal that some ice gets stuck. If the ice is not used
frequently, the older cubes of ice will be opaque in color,
smaller, and with a strange flavor.
CONNECTING THE WATER LINE
To determine how much pipe material is needed,
measures the distances between the valves located
behind the refrigerator and the source of water and add
to that 8 feet (2,4 m). Make sure there is sufficient pipe
material to allow the free movement of the refrigerator
from the wall
BEFORE START
The water source is not guaranteed by the refrigerator
manufacturer. Follow instructions carefully in order to
reduce damage.
Air located inside the water pipes can cause hammering
or tapping causing damage to the inner pipes or water
spillage in the inside of the refrigerator. Call a qualified
plumber to fix such hammering on the connections
before installing the water pipe.
ţ A cold water source. Water pressure should be between
0,138 and 0,82 MPa or 20 and 120 PSI for models not
containing water filter and between 0,276 and 0,82
MPa or 40 and 120 PSI for models containing water
filter.
To avoid burn damage or such, never connect refrigerator
to hot water pipes.
ţ A drill.
If you are to use the refrigerator before connecting it
to the water source, make sure the ice maker is the off
position.
ţ Adjustable 1/2” (12,7 mm) key.
Never attempt to install the ice maker pipes in areas
where room temperature is below freezing point.
ţ Two 1/4” (6,35 mm) diameter
compression nuts with two
sides to connect the copper
pipe to the refrigerator valve.
ţ Flat and Phillips style (star) screwdriver.
When using any electrical device (like a drill) during
the installation, make sure device is doubly isolated or
making ground to prevent risk of electrical surge or
discharge.
If your current copper pipe has some reduction on the
ends, it will be necessary to get and
adaptor (found in hardware stores)
to connect the water line to the
refrigerator. It is also possible to cut
such reductions with a pipe cutter
and use the compression connections mentioned above.
All installations should be done considering local water
and drainage requirements.
ţ If an inverted osmosis water filtration system is
connected to the cold water source, the water hose
installation is not assured or guaranteed by the
refrigerator or automated ice maker manufacturer.
Follow the next instructions carefully to minimize costly
water related damages.
ţ When having an inverted osmosis water filtration
system connected to the cold-water flow, the water
pressure for such system must be at least between
40-60 PSI or 0,27 MPa (2,8 kg · f / cm ² ~ 4,2 kg · f
/ cm ², (2,8 kg · f / cm ² ~ 4,2 kg · f / cm ², less than
2 ~ 3 seconds to fill a 7 oz of capacity cup [0,2 liters]).
ţ If the inverted osmosis water filtration system pressure
is less than 21 PSI or 0,14 MPa (1,5 kg · f / cm ², more
than four (4) seconds to fill a 7 oz of capacity cup [0,2
liters]):
a) Identify if the sediments filter in the inverted osmosis
system is being blocked. Replace filter if necessary.
b) Allow inverted osmosis system storage tank to refill
after extensive usage.
c) Call a qualified plumber if the inverted osmosis water
pressure problem continues.
ţ Bypass valve to connect to
the cold water line. The valve
must have a water opening
with an interior 5/32” (3,46
mm) diameter in the coldwater connection point. These
valves can be located in any cold-water connection
package. Before buying make sure such valve meets
local standards and requirements.
INSTALLATION INSTRUCTIONS
Install the valve to the pipe that you use to drink water.
(Connect only to a potable water source).
CAUTION: Connect to potable water supply only.
1. CLOSE THE MAIN WATER SOURCE
Open the nearest water faucet to let water flow and
empty pipes.
2. SELECT THE LOCATION OF THE VALVE
Select the location of the valve that will
provide a better access. It is best to
connect to a vertical pipeline. When
connecting to a horizontal pipeline is
necessary, make the connection in the
lateral or upper area instead of the
lower area to prevent accumulation of
sediment.
REQUIREMENTS
ţ 1/4” (6,35 mm) in diameter copper pipe to
connect refrigerator to the water pipe. Make
sure both terminals are cut in
squared manner.
2
CONNECTING THE WATER LINE
the pipe is completely inserted into the valve. Tighten
nut carefully.
3. DRILL A HOLE FOR THE VALVE
Drill a 1/4” (6,35 mm) diameter
hole in the water pipeline.
Remove jagged edges produces
after perforation. Make sure
water does not reach the drill.
Not performing the 1/4” (6,35
mm) perforation can lead to a
low or smaller ice production.
Saddle Type
Shutoff Valve
Packing Nut
4. TIGHTEN THE VALVE
Outlet Valve
Ferule (sleeve)
Tight the valve into the cold water pipeline with a tube
trap.
NOTE: Codes for 248 CMR pipelines of the state of
Massachusetts must be attached to the connection.
Valves of this type are banned in Massachusetts. Call an
authorized plumber.
Pipe Clamp
8. DRAIN THE PIPE
Saddle Type
Shutoff Valve
Open the main water source (1) and drain the pipe until
water comes out clear.
Vertical Cold
Water Pipe
NOTE: Codes for 248 CMR pipelines of the state of
Massachusetts must be attached to the connection.
Valves of this type are banned in Massachusetts. Call an
authorized plumber.
1
5. TIGHTEN THE TRAP
Allow water flow from the bypass valve (2) and close after
draining 1/4 of a gallon (1L) of water.
Tighten the trap until the sealing ring begins to grow.
NOTE: Make sure it is not too tight, this can break the
pipe.
Washer
Pipe Clamp
Inlet End
2
Clamp Screw
9. CONNECT PIPE TO REFRIGERATOR
NOTES:
ţ Before making connection to refrigerator, make sure
it is not connected to any energy source. If your
refrigerator does not have a water filter, it is advised
to install one.
ţ If your water source contains sand or related particles
that can travel to the valve, install a water filter near the
refrigerator.
6. PLACE THE PIPELINE
Place the pipeline between the cold water pipe and the
refrigerator. Place it through a hole in the wall or floor
(behind the refrigerator or next to the cabinet) as close
to the wall as possible.
NOTE: Make sure there is a sufficient amount of extra
pipeline (8 feet [244 mm] coiled up three times with a
10” [25 cm] in diameter) to allow free movement of the
refrigerator from the wall after installation was made.
IMPORTANT: Never use old or used hoses. Always use
new ones to have a better use and experience. Connect
always to a potable water source to avoid security and
health issues.
7. CONNECT PIPELINE TO VALVE
Place the compression nut and the copper pipe ferule at
the end of the pipe and connect to the valve. Make sure
CONNECTING THE WATER LINE
ţ Remove the ring plug (1) from the valve located at the
top of such device.
1
12. TURN ICE MAKER ON
Turn ice maker switch into the ON position. Ice maker
will start only after reaching its operating temperature
of 15 °F (-9 °C) or less. It will automatically begin the ice
production if switch is located in the ON position.
ţ Place compression nut and the ferule at the end of the
pipeline. Insert pipeline into the connection valve as far
as possible. Hold tightly while holding pipeline.
Compression
Nut 1/4”
Ferule
Hold on to the pipe from the handles or grabbers located
behind the refrigerator, loosing first the bolt holding the
handle. Afterwards, insert pipe into the hole and tighten
bolt to finalize.
10. OPEN THE BYPASS VALVE
Tighten
all
connections
containing leaks. Place access
cover back on compressor.
11. CONNECT TO REFRIGERATOR
Fix pipeline in a way that it does
not vibrate on the refrigerator or
wall. Push refrigerator against
wall.
TROUBLESHOOTING GUIDE
UNDERSTANDING SOUNDS YOU MAY HEAR
ţYou will hear a bell sound caused by the flow of the
refrigerant, water pipe or objects located on the superior
Your new refrigerator might produce certain noises that
part of the refrigerator.
your previous refrigerator did not. It is normal if you worry.
Most of the new sounds you will be hearing are actually
normal and expected. Hard surfaces like walls or floor ţYour refrigerator is designed to work efficiently to
can increase sounds and make them sound louder than
preserve your food at the desired temperature using
they really are. The following list has a description of such
the least of energy. You will be able to hear a pulsing
sounds along with their causes.
sound coming from the ventilators and the evaporator.
The speed of the ventilator can speed up when you
open the refrigerator door.
ţAfter each cycle you will hear a dripping sound due to
the refrigerant liquid in your refrigerator.
ţContraction and expansion of the inner walls can cause
a slight popping sound.
ţYou will hear a dripping sound caused during the
thawing cycle.
ţDuring the defrosting cycle the water might cause a
dripping sound.
ţYou can hear some tight air sound over the capacitor
caused by the fan.
ţRunning water can be heard during the defrosting
cycle.
ţThe thawing timer will make a “click” sound when such
timer will start and finish. Temperature controlling ţDue to its low energy consumption design of the
device will also make a “click” sound at the beginning
refrigerator; the fans will remain of, while the on-off
and ending of the refrigerator cycle.
switch activated the internal light of bin.
Problem
THE REFRIGERATOR
WON´T TURN ON
ţThe plug is correctly positioned.
ţFirmly plug the cord into a live outlet with proper
ţA fuse has gone bad or the circuit
voltage.
presents failures.
ţReplace the fuse or reset the circuit breaker.
ţThe refrigerator is in the defrosting ţWait about 30 minutes for defrost cycle to end.
cycle.
THE DISPLAY
SHOWS THE
WORD “OFF”
ţRefrigerator is in Demo Mode. ţThe Demonstration Mode disables the cooling
(Demonstration Mode)
system; only the lamps and display work
normally.
ţTo disable open refrigerator doors and then
press ICE PLUS
and REFRIGERATOR
buttons at the same time for 5 seconds.
THE LIGHT WON’T ţInterior lights have malfunctioned.
TURN ON
ţInterior lights are LED lightning, and repair
service must be performed by a qualified
technician.
STRANGE SOUNDS
OR SNOOZING/
VIBRATIONS
ţThe refrigerator is not correctly ţYou need to adjust the leveling screws due the
positioned.
floor is unleveled or weak. Read the Installation
section.
IT LOOKS LIKE
THE COMPRESSOR
MOTOR STAYS ON
TOO LONG
ţThe replaced refrigerator was an ţModern refrigerators with a bigger storage
capacity require longer periods of operation.
older model.
ţThe room temperature is hotter ţThe motor will continue working when the room
temperature is high. The motor might be on
than usual.
between 40% or 80% of the time. In high
temperature conditions, the capacitor might run
on periods of time.
ţThe door is being opened very often ţWhen adding or opening the door of the
refrigerator, it warms it up. It’s normal that the
or there has been a big amount of
refrigerator to run more that usual in order to cool
food in storage.
the bins. (Read the section Food Storage Guide).
To save energy, take what you need at once, order
your food in order so it can be easily found and
close the door immediately soon after you took
out the food.
ţThe refrigerator is plugged and the ţThe refrigerator will take 24 hours to cool down
completely.
control has been adjusted correctly.
ţPush firmly the Doors. If they don’t close. Read
ţDoors won’t close correctly.
Doors will not close completely below.
ţThis will stop the air transfer and marked the
ţThe condenser pipes are dirty.
motor to work longer and harder. Clean the pipes
of the condenser.
ţThe refrigerator is not leveled.
DOORS WILL
NOT CLOSE
COMPLETELY
ţThe food packages are blocking the
doors.
ţThe ice bin, the vegetable bin, the
panels and the shelves from the
door are out of place or position.
ţThe gaskets are sticking.
ţThe refrigerator wobbles or looks
instable.
ţThe doors were removed during
the installation and they weren’t
properly setup.
ţRead Refrigerator Installation section to level
refrigerator.
ţAdjust the food bins in order to free space
between the doors and the shelves.
ţPush the containers and place the vegetable cover
lid, the panels, shelves and any other container or
bin in their right positions. Read the section Using
your Refrigerator.
ţClean the seal rings and the surface they might be
in contact with. Use a piece of cloth with a small
amount of paraffin and apply it over the seal rings.
ţLevel the refrigerator. Read the section Closing
and Aligning the Doors.
ţRemove and place again the door according to
the section Refrigerator Doors: How to remove
and reverse.
THERE´S ICE ON
THE FOOD
ţThe door hasn’t been closed ţRead Doors Will not Close Completely already
completely.
mentioned.
ţThe door is frequently opened.
ţWhen the door is opened, warm, humid air is
allowed in the freezer resulting in frost.
THERE IS A WEIRD
TASTE AND SMELL
IN THE ICE
ţThe ice maker has been installed
correctly.
ţThe ice has been on storage too
long.
ţThe food hasn’t been packed in the
correct way.
ţThe water supply contains mineral
and sulfur.
ţThe inside of the refrigerator need
cleaning.
ţThe ice bin needs cleaning.
ţDon’t use the first ices made.
ţDispose of that old ice and make new.
ţPack again the food because it can transfer odors
and tastes to the ice.
ţYou might need to install a filter in order to
eliminate the odors and taste problems.
ţRead the section Refrigerator Care and Cleaning.
ţEmpty the bin and discard the old ice cubes.
TROUBLESHOOTING GUIDE
Problem
THERE´S WATER IN
THE DRAINING BIN
ţThe refrigerator is in defrosting ţThe water will evaporate. It is normal that some
cycle.
water falls on the bin.
ţIt’s more humid than usual.
ţIt might take a while for the water to evaporate.
This is normal when the weather is hot and humid.
THE
REFRIGERATOR
SEEMS TO MAKE
TOO MUCH NOISE
ţThe sounds may be normal for your ţRefer to the Understanding Sounds You May Hear
refrigerator.
section.
THE ICE MAKER IS
NOT PRODUCING
ICE OR ICE CUBES
ARE FREEZING
TOO SLOWLY
ţThe smallest size of ice cubes is ţWait 24 hours after hook-up for ice production.
selected.
See the Adjusting the Controls section.
ţDoor left open.
ţCheck to see if something is holding the door
open.
THE ICE CUBES
ARE TOO SMALL
ţSmaller cube size level is selected.
ţThe water supply valve is blocked.
ţSelect a bigger size for the ice cubes.
ţCall a plumber to clean the valve.
ţThe gaskets are dirty or sticky.
THE DOORS ARE
HARD TO OPEN
ţClean the gaskets and surface that they are in
contact with. Use a damp cloth with paraffin also
apply over the seal rings.
ţThe door opens itself as soon as ţWhen you open the door, the warm air enters
you close it.
in the refrigerator. When this air is cooled down
it occupies less volume and creates a vacuum
effect. If it is difficult to open wait 5 minutes then
check.
THE ICE MAKER
DOES NOT WORK
ţTurn the ice maker to the position on (I).
ţThe ice maker is off.
ţThe water supply is down or not ţRead the section Connecting the Water Line.
plugged.
ţWait 24 hrs for the freezer to reach its ideal
ţThe freezer temperature is warm.
temperature.
ţThe ice cubes turn off the ice maker. ţHand level the ice cubes.
ţThe air vents are blocked. The ţWith your hand find the vents and move and
package that might be blocking the air flow. See
cool air flows from freezer to the
the Multi Flow Section.
refrigerator and returns thru the
vents that dive this section.
ţWhen the doors are opened the warm and humid
ţThe doors open very easily.
air enters. To keep your refrigerator cool, take what
you need once and you’re your food organized to
make it easy to find. Close the door a soon as
you can.
ţThe refrigerator control has not been ţWait 24 hours to stabilize the temperature. If the
THE TEMPERATURE
adjusted for the room conditions.
temperature is cold or hot, move the control until
IS TOO HOT
the desire temperature is reached.
OR THERE´S
ţA large amount of food is just been ţAfter adding food to the refrigerator this will warm
HUMIDITY FORMED
placed inside the refrigerator.
up. It might take some hours for the refrigerator to
INSIDE THE
reach its temperature.
REFRIGERATOR
ţThe food has not been well packed ţWrap the food evenly and before packing anything
dry all the bins to avoid humidity. If it is necessary,
in each bin.
pack the food according to the section Food
Storage Guide.
ţThe doors haven’t been closed ţRead Doors will not Close Correctly section.
correctly.
ţIn humid weathers, the air contains humidity,
ţThe weather is humid.
which introduces it self if the doors are opened.
ţIt’s normal that some water props get formed
ţThe auto-defrosting cycle is over.
after the defrosting cycle is completed.
3
SMART DIAGNOSIS
TM
SMART DIAGNOSIS
(In some models).
Should you experience any problems with your
refrigerator, it has the capability of transmitting
data via your telephone to the LG service center.
This gives you the capability of speaking directly
to our trained specialists. The specialist records
the data transmitted from your machine and
uses it to analyze the issue, providing a fast and
effective diagnosis.
3. Press and hold the Freezer Temperature button for
three seconds while continuing to hold your phone to
the speaker.
If you experience problems with your refrigerator, call to the LG service center. Only use the
Smart Diagnosis TM feature when instructed to
do so by the LG call center agent. The transmission sounds that you will hear are normal
and sound similar to a fax machine.
Smart Diagnosis TM cannot be activated unless
your refrigerator is connected to power. If your
refrigerator is unable to turn on, then troubleshooting must be done without using Smart
Diagnosis.TM
Using Smart DiagnosisTM
First, call to the LG service center. Only use the
Smart Diagnosis TM feature when instructed to
do so by the LG call center agent.
1. Open the right refrigerator door.
2. Hold the mouthpiece of your phone in front
of the speaker that is located on the right hinge
of the refrigerator door, when instructed to do
so by the call center.
4. After you hear three beeps, release the Freezer
Temperature button.
5. Keep the phone in place until the tone transmission
has finished. This takes about 15 seconds, and the
display will count down the
time. Once the countdown is over and the tones have
stopped, resume your conversation with the specialist,
who will then be able to assist you in using the
information transmitted for analysis.
NOTE
For best results, do not move the phone while the
tones are being transmitted.
If the call center agent is not able to get an
accurate recording of the data, you may be asked
to try again.
NOTE
For other countries look for the phone service
technician attached warranty sheet.
3
Door in Door
Compartimento Door in Door
Montaje de caja Door in Door
Cajones de puerta Door in Door
Cajones inferiores Door in Door
1-2
3-4
5-7
8-10
40-41
41
42
43-49
43
43
44
45
47
49
50-56
50
50
52
52-55
52-53
53
53
53
54
54
54
54
54
55
55
55
55
3
57-58
57
57
57
57
57
57
57
57
58
58
58
59
60-62
63-66
Smart Diagnosis TM
50
50
50
51
51
56
56
5
6
56
56
67
1&-*(RO
ADVER5&/$*"
PRECA6$*’/
GU"3%&ESTA4*/STRUC$*0/E4
4
CONEXIÓN
ADVERTENCIA
Clavija de
3 terminales
ADVERTENCIA
PARTES Y CARACTERÍSTICAS
A
L
N
B
M
C
D
E
O
F
K
G
J
H
I
A Control Digital del Sensor
H Durabase
I Separador Durabase
N Montaje de Caja “Door-In-Door”
O Compartimento para Condimentos
* En algunos modelos
DESEMPAQUE
UNA VEZ INSTALADO
NOTA:
ADVERTENCIA
PELIGRO DE EXPLOSIÓN
INSTALACIÓN DEL REFRIGERADOR
HERRAMIENTAS QUE USTED PUEDE NECESITAR
10 mm
1/4 pulg
3/ pulg
8
1/4 pulg
3/
32 pulg
(2)
(1)
(9)
(8)
(10)
(3)
(5)
(11)
(12)
(4)
(6)
(7)
INSTALACIÓN DEL REFRIGERADOR
CÓMO QUITAR Y CAMBIAR LAS PUERTAS
DEL REFRIGERADOR (CONT.)
1
7
(14)
(13)
(5)
(6)
(4)
(3)
(9)
(2)
(11)
(8)
(10)
46
(12)
Fig. 4
Fig. 1
Canasta Inferior
Fig. 5
Fig. 2
Fig. 6
Tornillos
Fig. 3
CÓMO RETIRAR E INSTALAR EL CAJÓN
DESLIZABLE (CONT.)
Fig. 9
Tornillos
Fig. 7
Fig. 10
Canasta Inferior
Fig. 8
4
4
USO DEL REFRIGERADOR
TENGA CUIDADO AL CERRAR LA PUERTA
B
J
USO DEL REFRIGERADOR
GUÍA PARA ALMACENAR ALIMENTOS
ARTÍCULOS
CÓMO ALMACENARLOS
Queso
Leche
Fruta
Vegetales con
Hojas
Pescado
Carne
Sobras de
Alimentos
AJUSTE
RECOMENDADO:
Congelamiento
2
1
3
2
II
II
I
I
Figura A
Figura B
I
USO DEL REFRIGERADOR
ANAQUELES DE LAS PUERTAS
2
SECCIÓN DEL CONGELADOR
Cajón
1
2
1
2
3
4
1
2
1
1
2
3
3
2
2
5
CUIDADO DE SU REFRIGERADOR
CUBIERTA TRASERA
ADVERTENCIA
ADVERTENCIA
PELIGRO DE EXPLOSIÓN
CUBIERTA
TRASERA
5
CUIDADO DE SU REFRIGERADOR
INTERRUPCIONES DE ENERGÍA
CUIDADOS CUANDO USTED S& MUDA
PREPARÁNDOSE PARA LAS VACACIONES
Interruptor
Brazo Sensor
5
CÓMO CONECTAR LA TUBERÍA DE AGUA
ANTES DE COMENZAR
REQUERIMIENTOS
CÓMO CONECTAR LA TUBERÍA DE AGUA
6. ACOMODE LA TUBERÍA
2. SELECCIONE LA LOCALIZACIÓN DE LA
VÁLVULA
Tuerca de
Empaque
Trampa
Válvula Tipo
Llave
Férula (Manga)
1
Rondana
Trampa
Toma de Agua
Tornillo
2
CÓMO CONECTAR LA TUBERÍA DE AGUA
9. CONECTE LA TUBERÍA AL REFRIGERADOR
10. ABRA LA VÁLVULA DE PASO
Férula (Manga)
EL REFRIGERADOR
NO ENCIENDE
EL PANEL DE
CONTROL
MUESTRA LA
PALABRA “OFF”
SONIDOS
EXTRAÑOS O
VIBRACIÓN
GUÍA DE SOLUCIÓN DE PROBLEMAS
Problema
ţ-BTMVDFTJOUFSJPSFTOPGVODJPOBO
DPSSFDUBNFOUF
ţ-BTMVDFTJOUFSJPSFTTPOJMVNJOBDJ²O-&%ZTV
SFQBSBDJ²OEFCFTFSFGFDUVBEBQPSVOU¨DOJDP
DBMJżDBEP
LAS LUCES NO
ENCIENDEN
EL COMPRESOR
PARECE ESTAR
ENCENDIDO POR
MUCHO TIEMPO
ţ&MSFGSJHFSBEPSRVFGVFSFFNQMazBEP ţLPs SFGSJHFSBEPSFs NPEFSOPs DPO NBZPS
DBQBDJEBEEFBMNBDFOBKFSFRVJFSFONBZPSUJFNQP
FSBVONPEFMPBOUJHVP
EFPQFSBDJ²O
ţLaUFNQFSaUVSaBNCJFOUFFsU N T ţ&M NPUPS sFHVJS FO PQFSBDJ²O DVBOEP MB
UFNQFSaUVSa BNCJFOUF sFa BMUB &M NPUPS QVFEF
DBMJFOUFEFMPOPSNBM
FsUBSFODFOEJEPFOUSFVO40%Z80%EFMUJFNQP
&ODPOEJDJPOFsEFUFNQFSaUVSaBMUBFMDPNQSFsPS
QVFEFGVODJPOBSEVSBOUFMBSHPUJFNQP
ţLaQVFSUBsFBCSFNVZsFHVJEPPsF ţ"MBHSFHBSDPNJEBPBCSJSMBQVFSUBFMSFGSJHFSBEPS
ha BMNBDFOBEP VOB HSBO DBOUJEBE sF DBMJFOUB &s OPSNBM RVF FM SFGSJHFSBEPS PQFSF
QPSN TUJFNQPQBSaFOGSJBSMPsDPNQBSUJNFOUPT
EFBMJNFOUPT
(VFa MB Guía para Almacenar Alimentos
PaSB
BIPSSBS FOFSH¬B UPNF MP RVF OFDFTJUF FO VOB
sPMB PDBTJ²O NBOUFOHB MB DPNJEB PSEFOBEB
QBSaFODPOUSBSMBG DJMNFOUFZDJFSSFMBQVFSUBEFM
SFGSJHFSBEPSUBOQSPOUPDPNPsBRVFMBDPNJEB
ţ&M SFGSJHFSBEPS FsU FODIVGBEP ţ&M SFGSJHFSBEPS UBSEBS 24 IPSas QBSa FOGSJBSsF
Z FM DPOUSPM ha TJEP BKVsUBEP DPNQMFUBNFOUF
DPSSFDUBNFOUF
ţLas
QVFSUBT
OP
DJFSSBO ţ&NQVKFMBTQVFSUBTżSNFNFOUF4JOPsFDJFSSBO
DPNQMFUBNFOUF vFa a DPOUJOVBDJ²O Las puertas
DPSSFDUBNFOUF
no cierran completamente.
ţLa UVCFS¬B EFM DPOEFOsBEPS FsU ţ&sUP FWJUB MB USBOTGFSFODJB EF BJSF Z haDF RVF FM
NPUPSUSBCBKFQPSN TUJFNQP-JNQJFMBUVCFS¬B
sVDJB
EFMDPOEFOsBEPS
ţ&MSFGSJHFSBEPSOPFsU OJvFMBEP
LAS PUERTAS
NO CIERRAN
COMPLETAMENTE
ţLPs QBRVFUFs EF DPNJEB FsU O
PCsUSVZFOEPMBTQVFSUBT
ţ&M SFDJQJFOUF EF IJFMPT MB DVCJFSUB
EFvFHFUBMFTMPsQBOFMFTFsUBOUFT
DPOUFOFEPSFs EF QVFSUBT P
SFDJQJFOUFTFsU OGVFSBEFQPTJDJ²O
ţLPTFNQBRVFTsFMMPT
sFQFHBO
ţ&MSFGSJHFSBEPSsFUBNCBMFaPQBSFDF
JOFsUBCMF
ţ4F RVJUBSPO MBT QVFSUBT EVSBOUF
MB JOsUBMBDJ²O Z OP sF JOsUBMBSPO
BQSPQJBEBNFOUF
HAY CRISTALES
DE HIELO EN LA
COMIDA
ţVFa MB sFDDJ²O EF Instalación QBSa OJvFMBS FM
SFGSJHFSBEPS
ţ"SSFHMFMPsDPOUFOFEPSFsEFDPNJEBQBSaMJCFSBS
FTQBDJPFOUSFMBTQVFSUBTZMPTFsUBOUFT
ţ&NQVKF MPs DPOUFOFEPSFs Z QPOHB MB DVCJFSUB
EFMDBK²OEFvFHFUBMFTQBOFMFTFsUBOUFsZPUSPT
DPOUFOFEPSFsFOsVTQPTJDJPOFsDPSSFDUBTVFaMB
sFDDJ²OUso del Refrigerador.
ţ-JNQJFMPsFNQBRVFsZMBTsVQFSżDJFsRVFUPDBO
UsFVOUSBQPDPOVOQPDPEFQBSBżOBZBQM¬RVFMP
sPCSFMPTFNQBRVFT
ţ/JvFMF FM SFGSJHFSBEPSVFa MB sFDDJ²O EFCierre y
Alineación de Puertas.
ţQVJUFZWVFMWBaDPMPDBSMBTQVFSUBTEFBDVFSEPB
MBsFDDJ²OEF*OsUBMBDJ²OEFMRFGSJHFSBEPS
ţ/PsFhaDFSSBEPDPSSFDUBNFOUFMB ţVFBLas puertas no cierran completamenteBSSJCB
QVFSUB
NFODJPOBEB
ţLBQVFSUBsFBCSFGSFDVFOUFNFOUF ţCVBOEPMBQVFSUBsFBCSFFMBJSFUJCJPZI¹NFEP
FOUSaFOFMDPOHFMBEPSQSPvPDBOEPMBIVNFEBEZ
DSJsUBMFTEFIJFMP
GUÍA DE SOLUCIÓN DE PROBLEMAS
Problema
EL HIELO TIENE
SABOR Y OLOR
EXTRAÑOS
HAY AGUA EN EL
RECIPIENTE DE
DRENAJE
EL REFRIGERADOR
HACE RUIDO
LA FÁBRICA
DE HIELO NO
PRODUCE HIELO
O LO FABRICA
LENTAMENTE
LOS CUBOS
FABRICADOS SON
MUY PEQUEÑOS
LAS PUERTAS
SON DIFÍCILES DE
ABRIR
LA FÁBRICA
DE HIELO NO
FUNCIONA
5
GUÍA DE SOLUCIÓN DE PROBLEMAS
Problema
LA TEMPERATURA
ESTÁ MUY
CALIENTE O SE
HA FORMADO
HUMEDAD EN EL
INTERIOR
SMART DIAGNOSIS
TM
6
1-2
3-4
5-7
8-10
69-70
70
71
72-78
72
72
73
74-75
76-77
78
79-85
79
79
79
79
79
80
80
80-81
81-84
82
82
83
83
83
83
83
83
83
84
84
84
84
6
Door in Door
Compartiment Door in Door
Assemblage de la boîte Door in Door
Compartiment de porte Door in Door
Paniers inférieure Door in Door
85
85
85
85
85
88
89-91
92-95
96
DANGER
AVERTISSEMENT
ATTENTION
GARDEZ CES INSTRUCTIONS
6
BRANCHER A UNE SOURCE D’ELECTRICITE
AVERTISSEMENT
AVERTISSEMENT
PIÈCES ET CARACTÉRISTIQUES
A
L
N
B
M
C
D
E
O
F
K
G
J
H
I
A
I
B
J
C
Clayettes
K
D
L
M
E
Pantry*
N
Compartiment Door in Door
F
O
AVERTISSEMENT:
AVERTISSEMENT
RISQUE D´EXPLOSION
(5.08 cm) 2”
INSTALLATION DU RÉFRIGÉRATEUR
OUTILS NECESSAIRES
10 mm
1/4”
3/8”
1/4”
3/32”
Tournevis Phillips
Tournevis Plat
(2)
(1)
(9)
(8)
(10)
(3)
(5)
(11)
(12)
(4)
(6)
(7)
1
7
(14)
(13)
(5)
(6)
(4)
(9)
(3)
(11)
(12)
(2)
(8)
(10)
INSTALLATION DU RÉFRIGÉRATEUR
DÉPOSE ET REINSTALLATION DU TIROIR DU
CONGÉLATEUR
Fig. 4
Fig. 1
Durabase
ţ
Fig. 5
Fig. 6
Fig. 2
Fig. 3
Fig. 9
vis
Fig. 7
Fig. 10
Fig. 8
Durabase
bras du rail
7
ATTENTION LORS DE LA FERMETURE DE LA
PORTE
B
J
7
CONSERVATION DES ALIMENTS DANS LE
RÉFRIGÉRATEUR
ARTICLE
COMMENT CONSERVER
Lait
Oeufs
Fruit
Poisson
Viande
RÉGLAGE
RECOMMANDÉ:
2
1
AVERTISSEMENT
3
Figure A
Figure B
I I
I I
I
I
I
UTILISATION DU RÉFRIGÉRATEUR
SECTION DU CONGÉLATEUR
2
1
1
2
1
2
1
2
3
2
ENTRETIEN ET NETTOYAGE
AVERTISSEMENT
AVERTISSEMENT
RISQUE D´EXPLOSION
NETTOYAGE DE L’EXTÉRIEUR
REMPLACEMENT DU FILTRE À AIR FRAIS
8
ENTRETIEN ET NETTOYAGE
PANNE DE COURANT
CONSEILS DE DÉMÉNAGEMENT
8
8
CONDITIONS DE CANALISATION D´EAU
6. ACHEMINER LE TUYAU
Bague
(manchon)
1
Vis de pince
2
Bague
1
LE
RÉFRIGÉRATEUR
NE FONCTIONNE
PAS
RÉFRIGÉRATEUR
AFFICHE LE MOT
“OFF”
GUIDE DE DÉPANNAGE
Problème
VIBRATION ET
CLIQUETIS
L’ÉCLAIRAGE NE
FONCTIONNE PAS
ţ-FTMVNJ§SFTJOU¨SJFVSFTTPOUM¨DMBJSBHF-&%FU
S¨QBSBUJPOTEFEF©USFFGGFDUV¨TQBSVOUFDIOJDJFO
RVBMJż¨
MOTEUR DU
COMPRESSEUR
SEMBLE TROP
FONCTIONNER
PORTES NE
FERMANT PAS
ADÉQUATEMENT
GIVRE OU
CRISTAUX DE
GLACE SUR
LES ALIMENTS
CONGELÉS
GUIDE DE DÉPANNAGE
Problème
LE
RÉFRIGÉRATEUR
SEMBLE FAIRE
PLUS DE BRUIT
LA MACHINE À
GLAÇONS NE
PRODUIT PAS DE
GLAÇONS OU LES
GLAÇONS GÈLENT
TROP LENTEMENT
LES GLAÇONS
PRODUITS EST
TROP PETITS
LA MACHINE
À GLAÇONS
AUTOMATIQUE NE
FONCTIONNE PAS
TEMPÉRATURE
TROP CHAUDE OU
ACCUMULATION
D’HUMIDITÉ À
L’INTÉRIEUR
GUIDE DE DÉPANNAGE
Problème
LES PORTES SONT
DIFFICILES À
OUVRIR
SMART DIAGNOSIS
TM
SMART DIAGNOSIS
Utiliser Smart DiagnosisTM
9
LG Customer Information Center
1-800-243-0000
1-888-865-3026
1-888-542-2623
USA, Consumer User
USA, Commercial User
CANADA
Register your Product Online!
ww w.lg.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed