Mini-Rooter Operating Instructions

Mini-Rooter™
Operating Instructions
For 1-1/4” through 4” lines
(30mm—100mm)
Your Mini-Rooter is designed to give
you years of trouble-free, profitable service. However, no machine is better than
its operator.
Read, understand and follow all safety
warnings and instructions provided with
the product. Failure to follow the warnings
and instructions may result in electric
shock and/or serious injury. Save all warnings and instructions for future reference.
SAVE THESE INSTRUCTIONS!
Pour français voir la page 11
Para ver el español vea la paginá 21
Mini-Rooter™
Electric shock resulting in
death can occur if you plug
this machine into an improperly wired outlet. If the ground
wire is electrified, you can be
electrocuted by just touching
the machine, even when the
power switch is off. A ground
fault circuit interrupter will not protect you in this situation. Use a
UL approved tester to determine
if the outlet is safe.
WARNING! Read and understand all
instructions. Failure to follow all instructions
listed below may result in electric shock, fire
and/or serious personal injury. Replacement
manuals are available upon request at no
charge, or may be downloaded from our website, www.drainbrain.com. Instructional videos
are available for download on our website, and
may be ordered. If you have any questions or
problems, please call General’s customer
service department at 412-771-6300.
Do not operate power tools in
explosive atmospheres, such
as in the presence of flammable liquids, gases, or dust.
Power tools create sparks which
may ignite dust or fumes.
SAVE THESE INSTRUCTIONS!
These instructions are intended to
familiarize all personnel with the safe
operation and maintenance
procedures for the Mini-Rooter.
Only wear leather gloves.
Never use any other type of
glove, such as cloth, rubber, or
coated gloves. Never grasp a
rotating cable with a rag.
These items could become
wrapped around the cable and
cause serious injury.
SAFETY SYMBOLS
This is the safety alert symbol. It is
used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
Always wear safety glasses
and rubber soled, non-slip
shoes. Use of this safety equipment may prevent serious injury.
DANGER indicates a hazard with a high level of risk
which, if not avoided, will result in death or serious injury.
Never operate machine with
belt guard removed. Fingers
can get caught between belt and
pulley.
WARNING indicates a hazard with a medium level of risk
which, if not avoided, could result in death or serious injury.
Do not overstress cables.
Overstressing cables may cause
twisting, kinking, or breaking of
the cable and may result in serious injury.
CAUTION indicates a hazard with a low level of risk which,
if not avoided, will result in minor or moderate injury.
2
Mini-Rooter™
Personal Safety
GENERAL SAFETY RULES
1. Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
WARNING
Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or
serious injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts.
SAVE THESE INSTRUCTIONS!
Work Area
1. Keep work area clean and well lit. Cluttered benches and dark
areas invite accidents.
3. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in
tools that have the switch on invites accidents.
2. Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust or fumes.
4. Remove adjusting keys or switches before turning the tool
on. A wrench or key that is left attached to a rotating part of the
tool may result in personal injury.
3. Keep bystanders, children, and visitors away while operating
a power tool. Distractions can cause you to lose control.
5. Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enables better control of the
tool in unexpected situations.
Electrical Safety
1. Grounded tools must be plugged into an outlet, properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the
plug in any way. Do not use any adapter plugs. Check with a
qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tool should electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user.
6. Use safety equipment. Always wear eye protection. Dust
mask, non-skid safety shoes, hard hat, or hearing protection must
be used for appropriate conditions.
Tool Use and Care
1. Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or
against your body is unstable and may lead to loss of control.
2. Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is grounded.
2. Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate for
which it is designed.
3. Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
3. Do not use tool if switch does not turn it on or off. Any tool
that cannot be controlled with the switch is dangerous and must
be repaired.
4. Do not abuse the cord. Never use the cord to carry the tools
or pull the plug from an outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
4. Disconnect the plug from the power source before making
any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the
tool accidentally.
5. When operating a power tool outside use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.
5. Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.
6. Test the Ground Fault Circuit Interrupter (GFCI) provided with
the power cord to insure it is operating correctly before operating machine. Machine must have a properly functioning ground
fault circuit interrupter on the power cord. GFCI reduces the risk of
electric shock.
6. Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools, with sharp cutting edges are less likely
to bind and are easier to control.
7. Check for misalignment or binding of moving parts, breakage
of parts, and any other condition that may affect the tool‟s
operation. If damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained tools.
7. Extension cords are not recommended unless they are
plugged into a Ground Fault Circuit Interrupter (GFCI) found
in circuit boxes or outlet receptacles. The GFCI on the machine
power cord will not prevent electric shock from the extension
cords.
8. Only use accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one
tool may become hazardous when used on another tool.
8. Only use proper three-wire extension cords in good condition
which have three-prong grounding plugs and three-pole receptacles which accept the tool‟s plug. Use of damaged, inferior, or other extension cords will not ground the tool. Increases
the risk of electric shock and bodily injury or death.
Service
1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified repair
personnel could result in risk of injury.
9. Keep all electric connections dry and off the ground. Reduces
the risk of electric shock.
2. When servicing a tool, use only identical replacement parts.
Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance
Instructions may create a risk of electric shock or injury.
10. DO NOT touch plugs or tools with wet hands. Reduces the risk
of electric shock.
3
Mini-Rooter™
SPECIFIC SAFETY RULES
Ground Fault Circuit Interrupter (GFCI)
Your machine is equipped with a ground fault circuit interrupter, which
protects you against shock if a short circuit should occur. Check that
receptacle is properly grounded. Test the GFCI before each use.
1. Plug into 120-volt receptacle.
2. Push test button. Indicator light will go out and power to machine
should cut off.
3. If light does not go out when test button is pushed, DO NOT USE
THE MACHINE until proper repairs can be made.
4. To restore power after test, push reset button. With the reset button depressed, if the machine doesn't start, stops while running, or
if the operator experiences a mild shock, DO NOT USE THE MACHINE! Tag the machine out of service and take it to a motor
repair center or return it to the factory for repairs.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
Electric shock resulting in death can occur if you
plug this machine into an improperly wired outlet. If
the ground wire is electrified, you can be electrocuted
by just touching the machine, even when the power
switch is off. A ground fault circuit interrupter will not
protect you in this situation. Use a UL approved tester to
determine if the outlet is safe.
Do not overstress cables. Overstressing cables may
cause twisting, kinking, or breaking of the cable and may
result in serious injury.
THE SECTION OF CORD BETWEEN THE WALL PLUG
AND THE GFCI IS NOT IN THE PROTECTED CIRCUIT.
1. Only wear leather gloves. Never use any other type of glove,
such as cloth, rubber, or coated gloves. Never grasp a rotating
cable with a rag. These items could become wrapped around the
cable and cause serious injury.
FEATURES
2. Never operate machine with belt guard removed. Fingers can
get caught between belt and pulley.
Motor Switch
Mini-Rooter Closed Drum
3. Do not overstress cables. Keep leather-gloved hand on the cable for control when machine is running. Overstressing cables
because of an obstruction may cause twisting, kinking, or breaking
of the cable and may result in serious injury.
Belt Guard
V-Belt
4. Place the machine at a distance not greater than two feet from
the opening. Greater distances can result in cable twisting or
kinking.
Carrying Handle
Female
Connector
Cutter
Drum
5. Machine is designed for ONE-PERSON operation. Operator
must control foot switch and cable.
Cable
6. Do not operate machine in reverse (REV). Operating machine
in reverse can result in cable damage and is used only to back
cutting tool out of an obstruction.
Foot Pedal
NOTE: Do not operate machine if warning labels on the switch box
and power cord are missing or illegible.
7. Keep hands away from rotating drum. Do not reach into drum
unless machine is unplugged. Hand may be caught in the moving
parts resulting in serious injury.
8. Be careful when cleaning drains where cleaning chemicals
have been used. Avoid direct contact with skin and eyes. Drain
cleaning chemicals can cause serious burns as well as damage
the cable.
Mini-Rooter Open Drum
Motor Switch
9. Do not operate machine if operator or machine is standing in
water. Will increase risk of electrical shock.
Belt Guard
10. Wear safety glasses and rubber soled, non-slip shoes. Use of
this safety equipment may prevent serious injury.
V-Belt
11. Before starting each job, check that the cable in the drum is
not broken or kinked, by pulling the cable out and checking
for wear or breakage. Always replace worn out (kinked or broken) cables with genuine GENERAL replacement cables.
Carrying Handle
Female
Connector
Cutter
Cage
12. Only use this tool in the application for which it was designed. Follow the instructions on the proper use of the machine. Other uses or modifying the drain cleaner for other applications may increase risk of injury.
Cable
Foot Pedal
NOTE: Do not operate machine if warning labels on the switch box
and power cord are missing or illegible.
4
Mini-Rooter™
Cable Application Chart (Table 1)
Operation
Cable
Size
1/2"
Pipe
Typical
Max.
Applications
Size
Capacity
3" to 4" Roof Stacks and Small Floor Drains
75 ft.
(No roots)
3/8"
2" to 3" Roof Stacks, Laundry Lines & Small
75 ft.
Drains
*5/16" 1-1/2" Sinks, Basins & Small Drains
50 ft.
to 2"
1-1/4" Small Lines, Tubs & Shower Drains
*1/4"
50 ft.
to 2"
*The 1/4‖ and 5/16‖ diameter cables are for use with the J-Drum and
Dual Drum.
1. Begin by pulling the cable from the drum/cage and sliding it into
the drain as far as it will go.
2. Move the motor switch to the forward position.
3. With both hands (wearing leather gloves) on the cable, depress
the air foot pedal to start machine.
4. Feed the cable into the line and against the obstruction with a firm,
even pressure. Adjust the feeding rate to the resistance met. Do
not force the cable – let the cutter do the work. The job won’t get
done any faster and you could damage the cable.
DO NOT USE TOO MUCH FORCE –
LET THE CUTTER DO THE WORK.
5. Don't leave too much slack in the cable since this will cause whipping. If the cable starts to bend or build up too much twist, release
pressure on the foot pedal and rotate the drum in the opposite
direction to relieve the twist on the cable. Push any excess cable
back into the drum and then continue.
Cutter Application Chart (Table 2)
Cutter
Cat. #
Typical Applications
Cutters for 3/8” and 1/2”Cables
Arrow
Head
Boring
Gimlet
1-1/2‖
U-Cutter
2‖ Side Cutter
Blade
AH
Starting tool, ideal for cutting
and scraping.
BG
Starting tool, to remove loose
objects.
DO NOT ALLOW TOO MUCH SLACK IN THE CABLE
BETWEEN MACHINE AND DRAIN OPENING SINCE
THIS CAN CAUSE CABLE WHIPPING.
6. If you're having trouble getting around tight bends, try putting the
machine in reverse while applying steady pressure. (If using
Power Cable Feed, putting motor in reverse will cause the feed
control lever to operate opposite of normal.) Note: If your machine
is equipped with a momentary contact reverse switch, you must
hold the switch in position when operating the machine in reverse.
1-1/2UC Finishing tool, works well in
grease stoppages.
2SCB
Finishing tool, for scraping
inside edges of pipe.
Note: There are no fixed rules for what cutter to use. If one tool does
not take care of a stoppage, simply try another.
OPERATING INSTRUCTIONS
Set-Up
MAKE SURE THE MOTOR SWITCH IS IN
THE „OFF‟ POSITION!
1. Place machine within approximately
two feet (.6m) of drain opening. If you
can’t place the machine this close to
the drain opening, run the cable
through a metal guide tube to prevent
cable whipping.
Don't run motor in reverse for more than a few seconds at a
time as this could cause tangling in the drum or kinking.
7. If you still can't get around the bend, you're probably using too
large a cable. Switch to a 3/8" diameter cable, or even a smaller
one if necessary. (See Cable Application Chart—Table 1)
2. Position the foot pedal for easy accessibility. The machine is designed for
one-person operation. Be sure you
can quickly remove your foot from the
pedal in an emergency.
8. When the cable reaches the stoppage, allow the cable to progress
forward slowly, chewing into the stoppage as it goes. This slow
forward movement will reduce stress on the cable while doing a
more thorough cleaning job. A back and forth action often works
best.
3. Be sure the motor switch is in the off position.
4. Select the proper cutting tool (See Cutter Application Chart—Table
2). A good tool to start with is the Arrow Head or Boring Gimlet.
After the line is opened, follow with larger blades, which scrape
the inside edges of the pipe, assuring a real cleaning job.
Hint: It's often helpful to have a small stream of water running in the
line to wash the cuttings away while the machine is in operation and
after.
5. Insert the cutter into the female connector at the end of the 3/8" or
1/2" cable and tighten the connecting screw and lock washer firmly
in place.
5
Mini-Rooter™
9. Be careful not to let the cutter get caught in the stoppage as you
work through it. This can cause kinking and breaking of the cable.
When you feel the cable starting to twist in your hands, stop the
machine and pull back on the cable. This will free the cutter from
the obstruction. Then allow the cable to move forward slowly into
the stoppage. Remember, no cutting takes place when the blades
stop turning.
5. Tighten the knob at the top of the Power Cable Feed so that the
feed roller presses against the cable. Be sure not to over tighten
since this could cause excess cable wear. Note: The Power Cable
Feed is designed for use with 3/8‖ and 1/2‖ cables only.
10. After the line has been opened, retract the cable. Make sure the
motor switch is in the forward position. This is important to prevent the cable from tangling in the drum or in the line.
6. The feed lever controls the feeding rate and direction of the cable.
Move the lever down to feed the cable out of the drum. The further
the lever is moved downward, the faster the cable will feed out.
Move the lever up to retract the cable into the drum. When the
lever is in the middle (neutral) position, the cable will spin in place.
7. Move the motor switch to the forward position. Then, with a
gloved hand on the guide tube, depress the air foot pedal to start
machine.
8. Feed the cable into the line and against the obstruction with a firm,
even pressure. Adjust the feeding rate to the resistance met. Do
not force the cable – let the cutter do the work. The job won’t get
done any faster and you could damage the cable.
Note: In operation, use the least pressure possible to get the job
done in order to minimize wear on the feed and cable.
DO NOT USE REVERSE TO PULL THE CABLE OUT
OF THE DRAIN. RUNNING MACHINE IN REVERSE
CAN CAUSE THE CABLE TO TANGLE IN THE DRUM.
11. When the cutter is near the drain opening, take your foot off the
pedal to stop drum rotation. Never retract the cutter from drain
while cable is rotating. The cable could whip and cause serious
injury.
DO NOT USE TOO MUCH FORCE –
LET THE CUTTER DO THE WORK.
POWER CABLE FEED
(Optional. Cat. # PO-MR)
The variable speed Power Cable Feed is designed for use with 3/8‖
and 1/2‖ cables. If the feed was purchased separately, see ―How to
Install Power Cable Feed.‖
9. Don't leave too much slack in the cable since this will cause whipping. If the cable starts to bend or build up too much twist, release
pressure on the foot pedal and rotate the drum in the opposite
direction to relieve the twist on the cable. Push any excess cable
back into the drum and then continue.
1. Be sure you have read and understand the instructions for
manual feed before using the
Power Cable Feed. Misuse of the
feed can result in severe damage
to the cable.
2. Put the feed control handle in the
neutral position. Then, loosen the
feed pressure knob and pull three
feet of cable from the drum/cage.
3. Slide the guide tube (Cat. # MRGT) over the cable and snap the tube into place on the feed spout.
(Be sure to remove the cutter and connecting screw from the female connector first. Reattach desired cutter to cable after guide
tube is attached to feed.)
4. Place machine within approximately two feet of drain opening. Be
sure the Mini-Rooter Guide Tube (MR-GT) is in place. If you can’t
place the machine this close to the drain opening, run the cable
through the optional Guide Tube Extension (GTE) or a metal guide
tube to prevent cable whipping.
Feed Pressure Knob
DO NOT ALLOW TOO MUCH SLACK IN THE CABLE
BETWEEN MACHINE AND DRAIN OPENING SINCE
THIS CAN CAUSE CABLE WHIPPING.
10. When the cable reaches stoppage, put the feed in neutral. Then
allow the cable to progress forward slowly, chewing into stoppage
as it goes. This slow movement will reduce stress on cable while
doing a more thorough cleaning job. A back and forth motion often
works best.
11. Move the feed lever to the reverse position (upward) to retract the
cable. If more pulling power is required, the motor may be put in
reverse and the feed lever moved downward to forward position.
12. After the line has been opened, retract the cable by moving the
feed lever up. Make sure the motor switch is in the forward position. This is important to prevent the cable from tangling in the
drum or in the line.
Feed Control Lever
DO NOT RUN MOTOR IN REVERSE FOR MORE THAN A
FEW SECONDS AT A TIME SINCE THIS COULD CAUSE
THE CABLE TO KINK OR TANGLE IN THE DRUM.
Reverse
13. When the cutter is near the drain opening, take your foot off the
pedal to stop drum rotation. Never retract the cutter from drain
while cable is rotating. The cable could whip and cause serious
injury.
Neutral
Forward
6
Mini-Rooter™
SPECIAL OPERATIONS
HOW TO INSTALL 3/8" AND 1/2" CABLES IN DRUM
IF CABLE GETS CAUGHT IN LINE
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING CABLES OR DRUMS!
The motor can be reversed to free cable if it gets caught in the line.
Use the following procedure:
1. Move toggle switch on motor to reverse position.
2. Wearing leather gloves, pull on cable while the drum is turning in
reverse.
1. There is a socket inside the drum for the back end of the cable.
Rotate the drum so that the socket is at the bottom.
2. Position the distributor tube so that it is pointing downward.
3. Push the cable into the drum until there is
a full loop in the drum.
4. Reach into the drum, grasp the cable,
and bend it into the socket.
5. Remove V-Belt and rotate the drum to
the right, or clockwise, with one hand
while pushing cable into the drum with
the other hand.
DO NOT RUN MOTOR IN REVERSE FOR MORE THAN A
FEW SECONDS AT A TIME SINCE THIS COULD CAUSE
THE CABLE TO KINK OR TANGLE IN THE DRUM.
3. When the cable is freed, slide excess cable back into drum.
4. Move the toggle switch to the forward position again, and continue
at Step 3 of the Operating Instructions.
Note: The cable should lay in the drum in
a clockwise direction.
IF CABLE TANGLES IN DRUM
This is almost always caused by using too much pressure when feeding the cable, or by feeding the cable while running the machine in
reverse. To untangle, rotate drum in opposite direction. This will usually get the cable to lie in the drum properly
If cable has become badly tangled, which shouldn’t happen when
machine is used properly, it can be straightened out by removing the
distributor tube from the drum. To do this:
HOW TO USE J-DRUM
(Optional. Cat. No. MR-250)
The J-Drum holds 50 feet of 1/4‖ or 5/16‖
cable to be used when you need to clear
smaller 1-1/4‖ to 2‖ lines. These cables have a
basin plug head that can be spun through
most strainers. (See Cable Application
Chart—Table 1)
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING CABLES OR DRUMS!
1. Loosen the four bolts that hold the distributor tube cone on the
front of the drum.
2. Pull the cone and distributor tube forward, then pull the tangled
portion of the cable out of the drum.
3. After the cable has been straightened out, slide the distributor tube
and cone back along the cable until it can be repositioned and
bolted to the front of the drum.
4. Then, push the excess cable back into the drum.
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING CABLES OR DRUMS!
1. To install cable, open chuck jaws fully so that cable will pass
through easily.
2. Slide the back end of the cable (opposite to the end with basin
head) through spout and into the drum. The cable will be easier to
install if you bend the last inch of cable at a 45 degree angle.
3. When working through difficult stoppages or tight bends, tighten
the chuck to provide more torque and to prevent the cable from
tangling in the drum.
4. Clean and lubricate chuck regularly to prevent corrosion.
HOW TO REMOVE DRUM FROM MACHINE
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING CABLES OR DRUMS!
HOW TO USE DUAL-DRUM
1. Push down on the spring-loaded motor
and slide the V-Belt off the back of the
drum.
(Optional—Cat #MR-280)
The Dual-Drum holds two different diameter
cables at the same time. Inner and outer
drum compartments protect the cable from
tangling. You can easily switch from 1/4‖ to
5/16‖ or 3/8‖ cables without removing either
one from the drum.
2. Reach behind the drum and locate the
drum-retaining latch. Pull the latch to
release the drum shaft, then pull the
drum forward off of the machine.
3. To install the drum, simply slide drum
onto machine. The latch will lock automatically.
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING CABLES OR DRUMS!
4. Remove the belt guard by loosening retaining knob on top. Position the V-Belt around the drum, then press down on the motor
and slip V-belt onto the pulley. Be sure to reattach the belt guard.
1. Install 1/4‖ cable into the Dual-Drum by sliding the back end of the
cable (opposite to end with basin head) through spout and into the
inner drum. The cable will be easier to install if you bend the last
inch of cable at a 45-degree angle.
7
Mini-Rooter™
3. Fully loosen upper clamp knob on the feed support bracket and
snap the clamp over the Mini-Rooter’s upper frame. Center the
feed over the drum spout and slide the cable through the feed
rollers. Then moderately tighten the knob.
4. Loosen the two lower clamp cap screws to allow the clamps to fit
over the lower frame. Note that the ―short‖ clamp half should be
closest to the floor.
5. It may be necessary to loosen and re-adjust the upper tube length
to get the correct fit. Loosen the two set screws in the upper tube
and slide the assembly to get the best fit.
6. When alignment is correct, tighten the lower clamp set screws.
Screws should not be fully tightened. Make snug only so that the
bracket is able to pivot.
7. Fully tighten the upper tube set screws.
8. Test the bracket by loosening the knob and swinging the feed
assembly outward. It should disengage and swing smoothly.
9. Swing the feed assembly back and the clamp should snap into the
locked position. Tighten the knob to secure the feed for operation.
Do not attempt to use or transport the unit unless the upper clamp
knob is tightened.
2. Install the 5/16‖ or 3/8‖ cable into the outer drum by sliding the
back end of the cable (opposite to the end with the Female connector) through the spout. Reach one hand into the drum through
one of the two ports in the face of the drum and pull the cable end
to the left side of the outer drum. Then push another two feet of
cable into the drum while pulling the cable downward to form a
loop. The cable should lay in the drum in a clockwise direction.
3. Select the appropriate cable for the line you are working on. (See
Cable Application Chart—Table 1) If a 1/4‖ cable is required,
reach into the Dual-Drum and pull the cable out of the inner drum
and through the spout. If a larger cable is required, slide the 1/4‖
cable back though the spout, then reach into the drum and pull the
5/16‖ or 3/8‖ cable from the outer drum through the spout.
4. Each of the cables can be ―chucked‖ in place to provide more
torque by pressing the knurled knob against the spring and tightening it against the cable
Note: Use HE cables only in Dual-Drum—not EM cables.
HOW TO INSTALL DOLLY
(Optional. Cat. No. MR-W)
The dolly makes it easy to transport the Mini-Rooter to and from the
job. Designed especially for the Mini-Rooter, it snaps on and off in
seconds and holds the machine securely.
To install:
MAINTENANCE
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE PERFORMING MAINTENANCE!
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING DOLLY!
To keep your machine operating smoothly, it is essential that all bearings and distributor tube bushings be lubricated. Oiling moving parts is
particularly important where machine comes in contact with sand, grit
and other abrasive material.
1. Hold the dolly horizontally above the MiniRooter with the wheels toward the back of
the machine.
2. Tilt the top of the dolly down so the hooks
on the mid-point of the dolly slip under the
top crossbar of the machine. Then, lower
the wheels to the ground.
3. Step behind the machine. With one foot
on the axle, tilt the machine back.
4. Swing the locking brackets over the rear
gussets and tighten the knobs on either
side to hold the dolly securely in place.
CABLE MAINTENENCE
To get maximum service from your cables,
be sure that they are clean and well oiled.
This not only provides running lubrication
but greatly extends the life of the cables as
well. Some users periodically pour oil directly into the drum. Then, as the drum
turns, the cables get complete lubrication.
Our SNAKE OIL is ideally suited for this
purpose, since it not only lubricates the
cables, it deodorizes them as well.
HOW TO INSTALL POWER CABLE FEED
POWER FEED MAINTENANCE
(Optional. Cat. No. PO-MR)
Keep feed free of excessive soil and grit. It is recommended that the
feed be flushed with fresh water followed by a light oiling of the moving parts. No disassembly is normally required. Failure to feed can
usually be traced to the following possibilities:
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING POWER CABLE FEED!
1. Put the feed control lever in
the neutral (middle) position, then loosen the feed
tension adjustment knob
until the top feed roller lifts
out of the way.
2. Pull three feet of cable from
drum/cage. Remove cutter
and connecting screw from
cable.
DIRT ACCUMULATION
Over time, dirt can harden enough to stop roller rotation. Flushing with
water followed by liberal oiling can usually restore function. If disassembly is required, proceed as follows:
1. Remove the feed pressure knob, springs and spring plunger. Note
the positioning of these parts to ease re-assembly. The top roller
can now be removed.
2. Remove the snap rings and thrust washers from the bottom housing cylinders. The bottom rollers can now be removed.
3. Re-assembly is done in reverse order.
8
Mini-Rooter™
DAMAGED ROLLER
6.
Securely tighten the Axle to the Carrier with a 3/16‖ allen wrench.
Excessive use may wear a roller to the point of failure. It is recommended that all three rollers be replaced at the same time (Cat # POMR-703). The replacement roller is an assembly consisting of one
Feed Roller, two Feed Roller Bearings, and two Bearing Spacers.
Note: The Bearing Spacers must be installed between the Carrier
and each Feed Roller Bearing (as illustrated below) in order to
ensure proper operation and to obtain maximum Feed Roller life.
To Replace the Feed Roller Assembly:
1. Remove the Feed Roller Assembly by unscrewing and removing
the Feed Roller Axle.
2. For convenience, the components are assembled and wired together at the factory. Before attempting to install the assembly,
hold the assembly together and remove the wire.
3. While still holding the Feed Roller Assembly together, insert it into
the slot opening of the Carrier.
4. In order to help align the Spacers and Bearings, insert a pencil
point or similar object through the un-threaded end of the Axle
hole in the Carrier. After removing the pencil point, continue to
maintain the alignment of the components.
5. The Feed Roller Axle should then be inserted through the same un
-threaded Axle hole and should continue to be guided through the
Spacers and Bearings to the threaded Axle hole on the other side
of the Carrier.
TANGLED CABLE
If a cable loops over itself in the drum/cage, it will not feed properly.
Remove and reload the cable to restore function. If the cable kinks, it
is evidence of abuse and results from the use of too much pressure or
use of the wrong size cable for the line. Do not force the cable — let
the cutter do the work.
TROUBLE SHOOTING GUIDE (Table 3)
Problem
Probable Cause
Solution
Cable kinks or breaks.
Operator forcing the cable.
Do not force the cable. Let the cutter do the work.
Too much slack between machine
and drain.
Allow no more than two feet between machine and drain.
Cable used in wrong size drain line.
A cable that is too large or too small in diameter for a line is more likely
to kink. (Consult Table 1—Cable Applications.)
Cable exposed to acid.
Clean and oil cables regularly.
Operator forcing the cable.
Do not force the cable. Let the cutter do the work.
Machine running in reverse.
Do not run the machine in reverse to retract the cable from the drain.
Distributor tube frozen.
Lubricate distributor tube bushings.
Drum/cage stops while foot
pedal depressed.
Hole in pedal or hose.
Hole in diaphragm switch.
If no hole found in pedal or hose, replace diaphragm switch.
Drum/cage turns in one direction but not other.
Reverse switch or momentary contact switch failure.
Replace switch. Note: Momentary contact switch must be held in
place when using reverse.
Ground fault circuit interrupter
trips and will not reset.
Damaged power cord or extension
cord.
Replace cords.
Short circuit in motor.
Take motor to authorized repair center.
Faulty ground fault circuit interrupter.
Replace ground fault circuit interrupter.
Motor turns but drum/cage
does not.
Safety Slip Clutch (optional)
engaged.
Do not force cable.
Failure to feed.
Cable tangled in drum.
Do not run machine in reverse. Use proper cable size. (Consult Cable
Application Chart—Table 1).
Feed misadjusted.
If feed pressure knob is too loose the cable will slip. If it is too tight the
feed rollers will wear prematurely.
Feed roller frozen.
Clean and lubricate feed rollers regularly. Replace worn rollers.
Worn cable.
When cable coils wear flat, cable should be replaced.
Cable tangles in drum/cage.
9
Mini-Rooter™
See pages 31 and 32 for Parts List and Schematic Diagram.
10
Mini-Rooter™
CONSERVEZ CES INSTRUCTIONS !
12
Mini-Rooter™
CONSIGNES DE SÉCURITÉ GÉNÉRALES
CONSERVEZ CES INSTRUCTIONS !
SÉCURITÉ DU SITE
SÉCURITÉ PERSONNELLE
ÉLECTRICITÉ ET SÉCURITÉ
UTILISATION ET SOIN DE L'APPAREIL
ENTRETIEN ET RÉPARATIONS
LA PORTION DE CORDON COMPRISE ENTRE LA PRISE DE
COURANT ET LE DISJONCTEUR NE FAIT PAS PARTIE DU
CIRCUIT PROTÉGÉ.
14
Mini-Rooter™
CARACTÉRISTIQUES
Couteau
Courroie
en V
AH
BG
Couteau
Dévidoir
L’INTERRUPTEUR DE L'APPAREIL DOIT ÊTRE EN
POSITION ARRÊT (OFF) !
Couteau
Dévidoir
1-1/4 à 2 po
50 pi
50 pi
ALIMENTEUR DE CÂBLE AUTOMATIQUE
NE LAISSEZ PAS TROP DE CÂBLE ENTRE L'APPAREIL ET L'OUVERTURE DU DRAIN CAR LE CÂBLE RISQUERAIT DE FOUETTER.
Neutre
Marche avant
16
NE LAISSEZ PAS TROP DE CÂBLE ENTRE L'APPAREIL ET L'OUVERTURE DU DRAIN CAR LE CÂBLE
RISQUERAIT DE FOUETTER.
17
Mini-Rooter™
COMMENT UTILISER LE DÉVIDOIR DUAL-DRUM
COMMENT INSTALLER UN CÂBLE 1/2 OU 3/8 PO
DANS LE DÉVIDOIR
Mini-Rooter™
ENTRETIEN DU CÂBLE
Mini-Rooter™
L’ENSEMBLE ROULEAU D’ALIMENTATION
Ne forcez pas le câble.
Mini-Rooter™
Mini-Rooter™
REGLAS GENERALES DE SEGURIDAD
LA SECCIÓN DEL CORDÓN ENTRE EL ENCHUFE DE LA
PARED Y EL GFCI NO ESTÁ EN EL CIRCUITO PROTEGIDO.
24
Mini-Rooter™
CARACTERÍSTICAS
Cortador
Conector hembra
Cortador
Pedal
BG
ASEGÚRESE DE QUE EL INTERRUPTOR DEL MOTOR
ESTÉ EN LA POSICIÓN APAGADO (“OFF”).
Conector hembra
Cortador
Pedal
*5/16
pulg
*1/4
pulg
3/8
pulg
INSTRUCCIONES DE OPERACIÓN
Mini-Rooter con Tambor Abierto
Interruptor del
motor
AH
Tambor
Cable
OPERACIÓN
50 pies
25
NO PERMITA DEMASIADO HOLGURA EN EL CABLE
ENTRE LA MÁQUINA Y EL ORIFICIO DEL DESAGÜE YA
QUE ESTO PUEDE CAUSAR AZOTES DEL CABLE.
ALIMENTADOR AUTOMÁTICO DE CABLE
(Opcional. Núm. de pieza PO-MR)
Neutral
26
OPERACIONES ESPECIALES
NO USE DEMASIADA FUERZA:
DEJE QUE EL CORTADOR HAGA EL TRABAJO.
NO OPERE EL MOTOR EN REVERSA PARA MAS
DE UNOS SEGUNDOS A LA VEZ, YA QUE PUEDE
SER QUE SE PRODUZCAN ENREDOS O
TORCEDURAS EN EL TAMBOR.
27
CÓMO INSTALAR CABLES DE 1/2 Y 3/8 DE PULGADA
EN EL TAMBOR
¡DESCONECTE LA MÁQUINA DE LA FUENTE DE ALIMENTACIÓN ANTES DE INSTALAR UN CABLE O TAMBOR!
¡DESCONECTE LA MÁQUINA DE LA FUENTE DE ALIMENTACIÓN ANTES DE INSTALAR UN CABLE O TAMBOR!
CÓMO INSTALAR LA CARRETILLA
(Opcional. Núm. de pieza MR-W)
¡DESCONECTE LA MÁQUINA DE LA FUENTE DE ALIMENTACIÓN ANTES DE INSTALAR UN CABLE O TAMBOR!
28
Mini-Rooter™
MANTENIMIENTO DE LOS CABLES
CÓMO INSTALAR EL ALIMENTADOR AUTOMÁTICO
DE CABLE
(Opcional. Núm. de pieza PO-MR)
MANTENIMIENTO DEL ALIMENTADOR
¡DESCONECTE LA MÁQUINA DE LA FUENTE DE ALIMENTACIÓN ANTES E INSTALAR EL ALIMENTADOR
AUTOMÁTICO DE CABLE!
ACUMULACIÓN DE SUCIEDAD
RODILLO DAÑADO
Mini-Rooter™
MINI-ROOTER PARTS LIST
CAT. NO.
DESCRIPTION
MR-100-1
Complete Frame Assembly
MR-101
Frame Only
MR-102
Rubber Leg Tip (2)
MR-104
Shaft Retaining Pin
MR-104-A
Retaining Pin Spring
MR-104-B
Retaining Pin Collar
MR-105
Shaft Spacer
MR-200
Complete Drum Assembly (Enclosed)
MR-200-O
Complete Drum Assembly (Open)
MR-200-1
Drum w/Modified Distributor Tube
MR-200-2
Drum w/Inner Drum Cage
MR-201-2°
Drum Shell
MR-201-A-2° Rear Hub Assembly w/Bushing
MR-201-A-3 Rear Hub Assembly for Inner Drum
MR-201-C
Screws, Nuts & Lockwashers (5)
MR-201-D
Rear Hub Busing
MR-201-E
Retaining Screw
MR-201-O
Open Drum Cage
MR-201/202-2°
Complete Shaft & Hub Assembly
MR-202
Shaft
MR-202-A
Retaining Ring (2)
MR-202-B
Steel Washer
MR-202-C
Felt Washer
MR-202-D
Edging (2)
MR-204
Distributor Tube
MR-204-A
Distributor Tube Rear Collar w/Set Screw
MR-204-B
Distributor Tube Front Collar w/Set Screw
MR-204-2
Distributor Tube Spring & Inner Drum
MR-204-3
Inner Drum Cage (New Style)
MR-204-4
Flexitube Distributor Tube Assembly
MR-205
Fiber Washer (2)
MR-206
Front Hub
MR-206-A
Front Hub Bushing
MR-207
Round Head Cap Screw & Lockwashers (4)
MR-210
Drum Connecting Cable
MR-210-A
Connecting Cable Bolt, Nut, & Washer
MR-215
Distributor Tube Modification Kit
MR-216
Drum Retaining Bolt
MR-217
Drum Retaining Washer
MR-218
Felt Washer
MR-220
Inner Drum Cage
MR-250
"J" Drum (for 1/4" & 5/16" Cables)
MR-251-1°
Rear Shell
MR-252
Round Head Machine Screw & Nut (2)
MR-255-1♦
Front Drum Assembly for Collet Chuck
♦
MR-255-A-1 Spout Assembly for Collet Chuck
MR-255-B
Bushing
MR-257
Shaft for "J" Drum
MR-260-1♦
Collet Chuck Assembly
MR-280
Dual Drum Assy. (for 1/4", 5/16", & 3/8" Cables)
MR-281
Container Front
° Denotes part for Serial #21566 & Up
♦ Denotes part for Serial #23647 & Up
CAT. NO.
31
DESCRIPTION
MR-281-A Screws & Nuts (4)
MR-282
Container Back
MR-283
Chucking Assembly
MR-283-A Chuck Body
MR-283-B Knurled Knob
MR-283-C Spring
MR-283-D Screw
MR-284
Hub w/Bushing (MR-201-A-2)
MR-284-A Nuts & Bolts (5)
MR-285
Washer
MR-286
Shaft w/Snap Rings & Washers
MR-286-A Snap Rings (2)
MR-286-B Steel Washer
MR-286-C Felt Washer
MR-287
Collar w/Set Screw
MR-291
Internal Container Front
MR-292
Internal Container Back
MR-292-A Nuts, Lockwashers & Thumb Nuts (4)
MR-293
Beveled Collar
MR-300
Motor 1/3 hp w/GFCI, Foot Switch & Rev. Switch
A-MR-300
Motor w/Slip Clutch, GFCI, Foot Switch &
Reverse Switch
MR-301-A
10' Cord w/GFCI
MR-301-B
Knob for Mounting Stud
MR-301-D
Stud Replacement
MR-303
V-Belt Pulley
MR-303-1
Safety Clutch
MR-304-1*
Motor Support w/Bolts, Nuts, & Washers
MR-304-A
Guide Screws (2)
MR-305
Motor Support Spring
MR-306
V-Belt (45")
MR-307-2
Belt Guard w/Slot for Mounting Stud
MR-308
Foot Switch & Reverse Switch Assembly
MR-308-A
Box Only w/Cover & Screws
MR-308-B
Foot Pedal & Hose
MR-308-C
Hose Clamp (2)
MR-308-D
Foot Pedal Only
MR-308-E
Power Switch Diaphragm
MR-308-F
Air Hose
MR-308-G
Reverse Switch (3-Way)
MR-308-G-1
Momentary Contact Reverse Switch
MR-308-H
Rubber Boot (Open Cage Units Only)
MR-308-J
Barbed Adapter
MR-308-K
Switch Guard
MR-308-N
Strain Relief Nut
GFI-MR
Ground Fault Circuit Interrupter
MR-DECAL
Set of Safety Decals
MR-VIDEO
Instructional Video
PO-MR
Mini-Rooter Power Cable Feed
MR-GT
Guide Tube
EM3R8
Adapter
* Denotes part for Serial #08627 & Up

Denotes part for Serial #14933 & Up
Mini-Rooter™
General Wire Spring Co,
1101 Thompson Avenue
McKees Rocks, PA 15136
412-771-6300
www.drainbrain.com
© General Wire Spring Co. 2010