ELICA ELI136SS User manual

ELICA ELI136SS User manual
Use, Care, and Installation Guide
Guide d’utilisation, d’entretien et d’installation
Guía de instalación, uso y mantenimiento
READ AND SAVE THESE INSTRUCTIONS
LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES
LEA Y GUARDE ESTAS INSTRUCCIONES
LIB0099060A
11/14
EN
FR
ES
Contents
Sommaire
Contenido
page
page
página
2
13
24
Contents
APPROVED FOR RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
Important safety Notice................................................................................. 3
Electrical & Installation requirements ........................................................... 4
Before installing the hood ............................................................................. 4
List of Materials............................................................................................. 5
Parts supplied .............................................................................................. 5
Parts not supplied ........................................................................................ 5
Product Dimensions...................................................................................... 5
Location Requirements................................................................................. 6
Venting Requirements................................................................................... 6
Venting methods........................................................................................... 6
Installation .................................................................................................... 7
Mounting the range hood blower................................................................... 9
Make electrical connection........................................................................... 9
Complete Installation .................................................................................... 10
Check operation............................................................................................ 10
Range hood use............................................................................................ 10
Range hood care........................................................................................... 11
Warranty ....................................................................................................... 12
PLEASE READ ENTIRE INSTRUCTIONS BEFORE
PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local
Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit
for the owner.
OWNER: Please retain these instructions for future
reference.
Safety Warning: Turn off power circuit at service panel and
lock out panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit
2
READ AND SAVE THESE INSTRUCTIONS
Important Safety Notice
CAUTION
WARNING
FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO
EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR
VAPOURS.
TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT
OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:a
a) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or other
metal tray, then turn off the gas burner or the electric element. BE
CAREFUL TO PREVENT BURNS. If the flames do not go ou
immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - you may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a
violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a class ABC extinguisher, and you already
know how to operate it.
2) The fire is small and contained in the area where it started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer.
B. Before servicing or cleaning the unit, switch power off at service
panel and lock service panel disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
C. Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes & standards,
including fire-rated construction.
D. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (Chimney) of fuel burning equipment to
prevent back- drafting. Follow the heating equipment
manufacturers guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), the
American Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
E. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
F. Ducted systems must always be vented to the outdoors.
a
Based on “Kitchen Fire Safety Tips” published by NFPA.
OPERATION
a. Always leave safety grills and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose
clothing.
The manufacturer declines all responsibility in the event of failure to
observe the instructions given here for installation, maintenance and
suitable use of the product. The manufacturer further declines all
responsibility for injury due to negligence and the warranty of the unit
automatically expires due to improper maintenance.
CAUTION
To reduce risk of fire and to properly exhaust air, be sure to duct
air outside - do not vent exhaust air into spaces within walls,
ceilings, attics, crawl spaces, or garages.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.
Install this hood in accordance with all requirements specified.
WARNING
To reduce the risk of fire or electric shock, do not use this hood
with any external solid state speed control device.
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.
a) Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
flambeing food (i.E. Crepes suzette, cherries jubilee, peppercorn
beef flambe’).
c) Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
d) Use proper pan size. Always use cookware appropriate for the
size of the surface element.
3
Before installing the hood
Observe all governing codes and ordinances.
1. For the most efficient air flow exhaust, use a straight run or as few
elbows as possible.
CAUTION: Vent unit to outside of building, only.
2. At least two people are necessary for installation.
3. Fittings material is provided to secure the hood to most types of
walls/ceilings, consult a Qualified Installer, check if they perfectly
fit with your cabinet/wall.
4. Do not use flex ducting.
5. COLD WEATHER installations should have an additional back
draft damper installed to minimize backward cold air flow and a
nonmetallic thermal break to minimize conduction of outside
temperatures as part of the ductwork. The damper should be
on the cold air side of the thermal break. The break should be as
close as possible to where the ducting enters the heated portion of
the house.
6. Make-Up air: Local building codes may require the use of
make-up air systems when using ducted ventilation systems
greater than specified CFM of air movement. The specified CFM
varies from locale to locale. Consult your HVAC professional for
specific requirements in your area.
NOTE:
Use the Range Hoods models ELI136SS and ELI142SS (Dual Blower
Motor = 1200CFM) above cooktops rated higher than 65,000 Btus.
IMPORTANT
It is the customer’s responsibility:
• To contact a qualified electrical installer.
• To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70 —
latest edition*, or CSA Standards C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local
codes and ordinances.
• If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
• Do not ground to a gas pipe.
• Check with a qualified electrician if you are not sure range hood is
properly grounded.
• Do not have a fuse in the neutral or ground circuit.
IMPORTANT
Save Installation Instructions for electrical inspector’s use.
• The range hood must be connected with copper wire only.
• The range hood should be connected directly to the fused
disconnect (Or circuit breaker) box through metal electrical
conduit.
• Wire sizes must conform to the requirements of the National
Electrical Code ANSI/NFPA 70 — latest edition*, or CSA
Standards C22.1-94, Canadian Electrical Code Part 1 and C22.2
No. 0-M91 - latest edition** and all local codes and ordinances.
• A U.L.- or C.S.A.-listed conduit connector must be provided at
each end of the power supply conduit (at the range hood and at
the junction box).
Copies of the standards listed may be obtained from:
* National Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 441315575
4
List of Materials
Parts not supplied
Removing the packaging
CAUTION!
Optional Accessories
Remove carton carefully, wear gloves to protect against sharp edges.
WARNING!
Remove the protective film covering the product before putting into
operation.
Tools/Materials required
•
•
Parts supplied
•
•
•
•
•
•
•
•
•
•
•
•
•
Hood assembly with blower and light bulbs
Metal grease filters
Duct covers
Hardware bag with:
• Use, care and installation guide
• Installation template
• 4 - Duct cover plastic clips
• 4 - 6 x 16 mm blower mounting screws
• 4 - 5 x 45 mm mounting screws
• 6 - 3.5 x 6.5 mm mounting screws
• 2 - 3.5 x 9.5 mm mounting screws
• 60 - 4.2 x 8 mm mounting screws
• T10 TORX®† adapter
• T20 TORX®† adapter
Level
Drill with 1¼” (3.2 cm),⅛” (3.2 mm), and 5⁄16” (7.9 mm)
drill bits
Pencil
Wire stripper or utility knife
Tape measure or ruler
Pliers
Caulking gun and weatherproof caulking compound
Vent clamps
Jigsaw or keyhole saw
Flat-blade screwdriver
Metal snips
Parts needed
•
•
•
•
•
Home power supply cable
½” (12.7 mm) UL listed or CSA approved strain relief
3 UL listed wire connectors
1 wall or roof cap
8” round metal vent system
Product Dimensions
121⁄8”
(30.8 cm)
8”
(20.32 cm)
133⁄16”
(33.5 cm)
Max 463⁄16” (117.4 cm)
Min 332⁄8” (84.4 cm)
126⁄8”
(32.3 cm)
36”(91 cm)
42”(106.2 cm)
27”
(68.6 cm)
5
IMPORTANT: Observe all governing codes and ordinances. Have a
qualified technician install the range hood. It is the installer’s responsibility to comply with installation clearances specified on the model/
serial rating plate. The model/serial rating plate is located behind the
left filter on the rear wall of the vent hood.
Canopy hood location should be away from strong draft areas, such
as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
Grounded electrical outlet is required. See “Electrical Requirements”
section.
The canopy hood is factory set for venting through the roof or
wall. This range hood is not available for a Non-Vented (recirculating)
Installation. All openings in ceiling and wall where canopy hood will be
installed must be sealed.
(Ducted models only)
• Vent system must terminate to the outdoors, except for nonvented
(recirculating) installations.
• Do not terminate the vent system in an attic or other enclosed
area.
• Use metal vent only. Rigid metal vent is recommended.
Plastic or metal foil vent is not recommended.
• The length of vent system and number of elbows should be kept
to a minimum to provide efficient performance.
For the most efficient and quiet operation:
•
•
•
•
•
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard
is not applicable, the standard for Manufactured Home Installation
1982 (Manufactured Home Sites, Communities and Setups) ANSI
A225.1/NFPA 501A, or latest edition, or with local codes.
•
•
Use no more than three 90° elbows.
Make sure there is a minimum of 24” (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
Do not install 2 elbows together.
Use clamps to seal all joints in the vent system.
The vent system must have a damper. If the roof or wall cap has a
damper, do not use the damper supplied with the range hood.
Use caulking to seal exterior wall or roof opening around the cap.
The size of the vent should be uniform.
Venting Methods
This canopy hood is factory set for venting through the roof or wall. A
8” (20.32 cm) round vent system is needed for installation (not included).
NOTE: Flexible vent is not recommended. Flexible vent creates back
pressure and air turbulence that greatly reduce performance. Vent
system can terminate either through the roof or wall.
Cabinet Dimensions
Roof Venting
A
Wall Venting
C
A
See NOTE
B
B
A
36” (91.4 cm)
Countertop
height
A. Roof cap
B. 8” (20.3 cm) round vent
IMPORTANT:
Minimum distance “A”: 30” (76.2 cm) from cooking surface.
Suggested maximum distance “A”: 36” (91.4 cm) from cooking surface.
NOTE: The hood chimneys are adjustable and designed to meet
varying ceiling or soffit heights depending on the distance “A”
between the bottom of the hood and the cooking surface.
6
A. Wall cap
B. 8” (20.3 cm) round vent
C. 90° elbow
Installation
Install Range Hood
•
Place the template in the ceiling considering the instructions for
ceiling support structures.
Always consider the front of hood legend when playing the
template on the ceiling. It will define the control’s location.
•
Mark with a pencil the hole locations for screws and duct in the
ceiling.
•
Fix the upper horizontal support with 4 wood screws.
•
Attach the 4 lower vertical supports to the hood with
8 - 4.2 x 8mm screws.
Ceiling Support Structures
• This vent hood is heavy.
Adequate structure and support must be provided in all types of
installations.
• At the hood location, install 2”x 4” cross framing between ceiling
joists as shown. (2”x 4” are required to support the weight of the
hood.)
• Arrange cross framing in the ceiling to suit the existing structure.
• Your ceiling joists will be like one of the following examples.
IMPORTANT
Framing must be capable of supporting 150lbs.
EXAMPLE A
NOTE: Top view ceiling joists parallel to front of hood
101⁄16” (25.5 cm)
install cross-framing
symmetrically over
duct/cooktop
Centerline
71⁄16”
(17.9 cm)
Align duct to
center of cooktop
hood front
Cooktop
outline
EXAMPLE B
NOTE: Top view ceiling joists parallel to front of hood
101⁄16” (25.5 cm)
install cross-framing
symmetrically over
16” (40.6
duct/cooktop
cm) joist
spacing
Centerline
71⁄16”
(17.9 cm)
2” x 4” cross
framing
hood front
Align duct to
center of cooktop
Cooktop
outline
EXAMPLE C
NOTE: Top view ceiling joists parallel to front of hood
2” x 4” cross
framing
101⁄16” (25.5 cm)
install cross-framing
symmetrically over
duct/cooktop
71⁄16”
(17.9 cm)
hood front
Align duct to
center of cooktop
Cooktop
outline
7
•
Attach the lower horizontal support to the hood with 8 - 4.2 x 8mm screws.
•
Attach the middle horizontal support to the hood with
8 - 4.2 x 8mm screws.
Mounting the
range hood blower
1. Slide the rear mounting plate flange under the bracket.
B
•
Attach the 4 upper vertical supports to the hood with
16 - 4.2 x 8mm screws.
A
A. Bracket
B. Blower mounting plate
2. Push the front end of the mounting plate up and snap into spring
tab.
NOTE: The spring tab should be outside of the slot in the mounting
plate.
B
•
Attach the assembly to the support fixed on the ceiling.
Assure it with 16 - 4.2 x 8mm screws.
A. Blower mounting plate
B. Spring tab
8
A
6. Tighten the strain relief screws.
3. Align mounting holes and install 4 - 6 x 16 mm screws.
A
E
F
C
B
D
B
A
A. Screw with lock washer
B. Mounting hole
A.White wires
B. Black wires
C. UL listed wire connectors
4. Attach power cord connector to connector on wire box on blower
motor mounting plate.
D. Green, Bare or Yellow/Green wires
E. Home power supply
F. UL listed or CSA approved ½” strain
relief
7. Use UL listed wire connectors and connect black wires (B)
together.
8. Use UL listed wire connectors and connect white wires (A)
together.
9. Connect green (or bare) ground wire from home power supply
to the green/yellow ground wire (D) in terminal box using UL
listed wire connectors.
10. Install terminal box cover.
11. Check that all light bulbs are secure in their sockets.
12. Reconnect power.
Complete Installation
Make Electrical Connection
•
Secure the 8” (20.3 cm) round vent transition with damper to top
of the range hood using 2 - 3.5 x 9.5 mm screws.
•
Attach the upper duct covers using 6 - 3.5x6.5 mm screws.
WARNING: Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Locate junction box of the range hood.
3. Remove terminal box cover and set aside.
A. Knockout in canopy back into terminal box
4. Remove knockout from terminal box and install a UL
listed or CSA approved ½” strain relief.
5. Place the range hood near its mounting position and run the
power supply cable through the strain relief into terminal box
(enough to make connection).
9
•
Place lower duct covers using one plastic bracket at each side
(4 needed).
Check Operation
1. Install grease filters. See the “Range Hood Care” section.
2. Install heat lamps into heat lamp sockets.
3. Check operation of the range hood blower and lights. See the
“Range Hood Use” section.
A
B
C
E
•
The lower duct cover shall be secured to rangehood by 4 screws.
D
A
A. Halogen lamps
B. Lamps knob
C. Blower knob
D. Filter handles
E. Grease filter
4. If range hood does not operate, check to see whether a circuit
breaker has tripped or a household fuse has blown.
Disconnect power supply and check that the wiring is correct.
NOTE: To get the most efficient use from your new range hood, read
the “Range Hood Use” section.
Range hood use
•
•
Install the grease filter and turn power on at service panel.
Check operation of the hood.
The range hood is designed to remove smoke, cooking vapors and
odors from the cooktop area. For best results, start the hood before
cooking and allow it to operate several minutes after the cooking is
complete to clear all smoke and odors from the kitchen.
The hood controls are located on the center side of the range hood.
A
B
A. Lamps knob
B. Blower knob
Operating the lamps
1. Turn the light switch to the “LOW” position to turn the range hood
lights On.
2. Turn the light switch to the “HI” position to turn the range hood
lights at its higher intensity.
3. Turn the light switch to the “OFF” position to turn the range hood
lights Off.
Operating the blower
1. Turn the blower switch at “1” to turn the range hood on.
2. Turn the blower switch to the desired speed position.
3. Turn the blower switch to the “HI” position to turn the range hood
on High.
4. Turn the blower switch to the “OFF” position to turn the range
hood blower Off.
10
Range hood care
Replacing an Halogen Lamp
Turn off the range hood and allow the halogen lamp to cool. To avoid
damage or decreasing the life of the new lamp, do not touch lamp
with bare fingers. Replace lamp, using tissue or wearing cotton gloves
to handle lamp. If new lights do not operate, make sure the lamps are
inserted correctly before calling service.
1. Disconnect power.
2. Use a flat-blade screwdriver and gently pry the light cover loose.
Metal Filters and Drip Trays:
1. Use 2 hands to remove filters.
2. Grasp filter handles, pull toward the front of range hood and pull
down on the rear handle to remove. Repeat for each filter.
A
A. Grease filter
3. Remove grease drip tray.
3. Remove the lamp and replace with a 120-volt, 40-watt
maximum, halogen lamp made for a G-9 base.
4. Replace the light cover.
5. Reconnect power.
6. Turn the light switch to the “OFF” position to turn the range hood
lights Off.
Cleaning
Exterior surfaces:
To avoid damage to the exterior surface, do not use steel wool or
soap-filled scouring pads. Rub in direction of the grain line to avoid
scratching the surface.
Always wipe dry to avoid water marks.
■■ Stainless Steel Cleaner and Polish.
■■ Mild liquid detergent and water.
■■ Wipe with damp soft cloth or non abrasive sponge, then rinse
with clean water and wipe dry.
A
A. Drip tray
4. Wash metal filters and grease trays as needed in dishwasher or
hot detergent solution to clean.
5. Replace grease drip tray.
6. Reinstall filters, grasp filter handles and place front edge of filter
into the hood.
7. Push up on the back handle and set rear of filter into the drip tray
to secure. Repeat for each filter.
A
A. Grease filter
11
WARRANTY
ELICA North America
TWO-YEARS LIMITED WARRANTY
TO OBTAIN SERVICE UNDER WARRANTY
Owner must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in order to obtain service
under warranty.
PARTS AND SERVICE WARRANTY
For the period of two (2) years from the date of the original purchase, Elica will provide free of charge, non consumable parts or components
that failed due to manufacturing defects. During these two (2) years limited warranty, Elica will also provide free of charge, all labor and in-home
service to replace any defective parts.
WHAT IS NOT COVERED
•
•
•
•
•
•
•
•
•
•
Damage or failure to the product caused by accident or act of God, such as, flood, fire or earthquake.
Damage or failure caused by modification of the product or use of non-genuine parts.
Damage or failure to the product caused during delivery, handling or installation.
Damage or failure to the product caused by operator abuse.
Damage or failure to the product caused by dwelling fuse replacement or resetting of circuit breakers.
Damage or failure caused by use of product in a commercial application.
Service trips to dwelling to provide use or installation guidance.
Light bulbs, metal or carbon filters and any other consumable part.
Normal wear of finish.
Wear to finish due to operator abuse, improper maintenance, use of corrosive or abrasive cleaning products/pads and oven cleaner products.
WHO IS COVERED
This warranty is extended to the original purchaser for products purchased for ordinary residential use in North America (Including the United
States, Guam, Puerto Rico, US Virgin Islands & Canada).
This warranty is non-transferable and applies only to the original purchaser and does not extend to subsequent owners of the product. This warranty is made expressly in lieu of all other warranties, expressed or implied, including, but not limited to any implied warranty of merchantability
or fitness for a particular purpose and all other obligations on the part of Elica North America, provided, however, that if the disclaimer of implied
warranties is ineffective under applicable law, the duration of any implied
warranty arising by operation of law shall be limited to two (2) years from the date of original purchase at retail or such longer period as may be
required by applicable law.
This warranty does not cover any special, incidental and/or consequential damages, nor loss of profits, suffered by the original purchaser, its customers and/or the users of the Products.
WHO TO CONTACT
To obtain Service under Warranty or for any Service Related Question
Please Call:
• Elica North America Authorized Service at (888) 732-8018
Or by Writing To:
• Elica North America, Attention Customer Service
6658 156th Avenue SE,
Bellevue, WA 98006 USA
[email protected]
12
APPROUVÉ POUR LES APPAREILS RÉSIDENTIELS
POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.
LIRE ET CONSERVER CES INSTRUCTIONS.
VEUILLEZ S.V.P. LIRE AVANT DE COMMENCER.
INSTALLATION DOIT ÊTRE CONFORME AUX CODES LOCAUX.
13
a
14
Avant d’installer la hotte
IMPORTANT
IMPORTANT
ATTENTION
AVERTISSEMENT
15
Enlever l’emballage
ATTENTION
•
•
•
•
•
AVERTISSEMENT
•
•
•
•
•
•
•
•
•
•
•
•
8”
(20.32 cm)
133⁄16”
(33.5 cm)
Max 463⁄16” (117.4 cm)
Min 332⁄8” (84.4 cm)
126⁄8”
(32.3 cm)
36”(91 cm)
42”(106.2 cm)
27”
(68.6 cm)
16
•
•
Dimensions
•
•
•
A
A
B
B
17
Installation
Installez la hotte de la cuisinière
•
•
•
•
71⁄16”
(17.9 cm)
71⁄16”
(17.9 cm)
18
•
•
B
•
A
•
19
A
A
F
C
B
D
Achever l’installation
•
•
1.
2.
3.
4.
A
C
B
20
•
A
B
C
E
•
D
A
A
B
21
Nettoyage
A
A
A
22
GARANTIE
ELICA North America
GARANTIE DE DEUX ANS
POUR OBTENIR UN DEPANNAGE SOUS GARANTIE
GARANTIE PIECES DE RECHANGE ET MAIN D’OEUVRE
CE QUE LA GARANTIE NE COUVRE PAS
•
•
•
•
•
•
•
•
•
•
QUI EST COUVERT
QUI CONTACTER
23
APROBADO PARA APARATOS DE USO
DOMÉSTICO
SÓLO PARA USO DOMÉSTICO
LEA Y GUARDE ESTAS INSTRUCCIONES
24
LEA Y GUARDE ESTAS INSTRUCCIONES
Aviso de seguridad importante
PRECAUCIÓN
SÓLO PARA USO DE VENTILACIÓN GENERAL. NO UTILIZAR
PARA EXPULSAR VAPORES O MATERIALES PELIGROSOS O
EXPLOSIVOS.
ADVERTENCIA
PRECAUCIÓN
ADVERTENCIA
a
ADVERTENCIA
25
IMPORTANTE
26
ADVERTENCIA
Partes suministradas
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
8”
(20.32 cm)
133⁄16”
(33.5 cm)
Max 463⁄16” (117.4 cm)
Min 332⁄8” (84.4 cm)
126⁄8”
(32.3 cm)
36”(91 cm)
42”(106.2 cm)
27”
(68.6 cm)
27
•
•
•
•
A
C
A
ver NOTA
B
B
A
28
•
•
•
71⁄16”
(17.9 cm)
2” x 4”
cruzados
madera.
71⁄16”
(17.9 cm)
2” x 4”
cruzados
29
•
B
A
•
•
30
A
A
E
F
C
B
D
B
A
A. Tornillo con rondana
B. Orificio de montaje
•
31
•
A
B
C
E
•
D
A
A. Lámparas halógenas
B. Control de lámparas
C. Control de velocidades
A
B
32
A
Limpieza
A. Filtro de grasa
A
A. Grasera
A
A. Filtro de grasa
33
GARANTÍA
ELICA Norte América
GARANTIA LIMITADA A DOS AÑOS
PARA OBTENER SERVICIO DENTRO DE GARANTIA.
PARTES Y GARANTIA DE SERVICIO.
QUE NO ESTA CUBIERTO
•
•
•
•
•
•
•
•
•
•
QUIEN ESTA CUBIERTO
A QUIEN CONTACTAR
34
LIB0099060A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed