imPOrTaNT SaFeTY iNSTrUcTiONS

imPOrTaNT SaFeTY iNSTrUcTiONS
360º ceramic
SURROUND HEATER
Model HZ-420 Series
Model HZ-430 Series
Model HZ-440 Series
IMPORTANT SAFETY
INSTRUCTIONS
WARNING – READ AND SAVE THESE
OPERATING AND SAFETY INSTRUCTIONS
BEFORE USING THIS HEATER. IF YOU DO
NOT UNDERSTAND THESE INSTRUCTIONS
OR PRODUCT LABELS PLEASE CALL OUR
CUSTOMER REPRESENTATIVES AT
(800) 477-0457 FOR ASSISTANCE
BEFORE USING THIS PRODUCT.
Warning – Failure to follow any of these
safety instructions could result in fire, injury
or death.
YOUR RESPONSIBILITIES
Electrical appliances may expose people to
hazards that can cause severe injury as well
as death. The use of electrical products may
create hazards that include, but are not limited
to, injury, fire, electrical shock and electrical
system damage. These instructions are
intended to provide you with the information
you need to use the product and to avoid such
hazards.
When using electrical appliances, basic
precautions should always be followed
to reduce risk of fire, electric shock, and
injury to persons including the following:
1. Warning – Read all instructions before
using this heater.
2. Warning – This heater is hot when in
use. To avoid burns, do not let bare skin
touch hot surfaces. If, provided, use
handles when moving this heater. Keep
combustible materials, such as furniture,
pillows, bedding, papers, clothes, and
curtains at least 3 feet (0.9 m) from the
front of the heater and keep them away
from the sides and rear.
3. Warning – Extreme caution is necessary
when any heater is used by or near
children or invalids, and whenever the
heater is left operating and unattended.
4. Warning – Always unplug heater when
not in use.
5. Warning – Do not operate any heater
with a damaged cord or plug or after the
heater malfunctions, has been dropped or
damaged in any manner. Discard heater or
return heater to authorized service facility
for examination and/or repair.
6. Warning – For residential use only.
7. Warning – Do not use outdoors.
8. Warning – This heater is not intended
for use in bathrooms, laundry areas and
similar indoor locations. Never locate
heater where it may fall into a bathtub or
other water container.
9. Warning – Do not run cord under
carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not
route cord under furniture or appliances.
Arrange cord away from traffic area and
where it will not be tripped over.
The Honeywell trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product
1
10.CAUTION – THIS APPLIANCE HAS A
POLARIZED PLUG (ONE BLADE IS WIDER
THAN THE OTHER). TO REDUCE THE RISK
OF SHOCK, THIS PLUG IS INTENDED TO
FIT ONLY ONE WAY IN A POLARIZED
OUTLET. IF THE PLUG DOES NOT FIT
SECURELY IN THE OUTLET, REVERSE
THE PLUG. IF IT STILL DOES NOT FIT,
CONTACT A QUALIFIED ELECTRICIAN. DO
NOT ATTEMPT TO DEFEAT THIS SAFETY
FEATURE.
11.Warning – This heater draws 12.5 amps
during operation. To prevent overloading
a circuit, do not plug the heater into a
circuit that already has other appliances
working.
12.Warning – It is normal for the plug to
feel warm to the touch; however, a loose
fit between the AC outlet (receptacle)
and plug may cause overheating and
distortion of the plug. contact a qualified
electrician to replace loose or worn outlet.
13.Warning – To disconnect the heater,
first turn off the product, then grip the
plug body and pull it from the wall outlet.
Never pull by the cord.
14.Warning – Do not insert or allow foreign
objects to enter any ventilation or exhaust
opening as this may cause an electric
shock or fire, or damage the heater.
15.Warning – To prevent a possible fire, do
not block air intakes or exhaust in any
manner. Do not use on soft surfaces, like
a bed, or where openings may become
blocked.
16.Warning – A heater has hot and arcing
or sparking parts inside. Do not use it in
areas where gasoline, paint or flammable
liquids are used or stored.
17.Warning – Use this heater only as
described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.
2
18.Warning – Always plug heater directly
into a wall outlet/receptacle. Never use
with an extension cord or relocatable
power tap (outlet/power strip).
19.Warning – Never tamper with this
product or attempt to fix it. Any tampering
with, or modification of this product can
result in serious injury, death, or fire. Risk
of electric shock. Do not open. No user
serviceable parts inside.
20.Warning – Do not remove product
labels that contain warnings or safety
instruction.
21.Caution – The output of this heater may
vary and its temperature may become
intense enough to burn exposed skin. Use
of this heater is not recommended for
persons with reduced sensitivity to heat
or an inability to react to avoid burns.
22.Caution – Before cleaning, or storage,
or when not in use, turn the product’s
controls to the OFF position and unplug
the heater from the electrical outlet and
allow to cool.
23.Caution – Place the heater on a firm,
level, open surface free from obstructions
and at least 3 feet (0.9 m) away from any
combustible materials. DO NOT use on
an unstable surface such as bedding or
deep carpeting. Be sure the heater is not
in a position where it may be tripped over
by small children or pets. The heater’s
rubber feet will hold it firmly in position.
24.Caution – If your home has aluminum
wiring have a licensed electrician check
your receptacle’s connections. When
using a 1500 watt heater, aluminum wire
connections can cause a safety issue.
SAVE THESE
INSTRUCTIONS
25.
ABOUT CERAMIC TECHNOLOGY
Ceramic heaters generate heat by passing electricity through heating wires embedded in ceramic plates.
This type of heating technology provides consistent, even heating.
The 360º Ceramic Surround Heater has an organic industrial design that maximizes heat output. It is
designed with fan power to improve convection in order to provide both all around or directional heating
comfort to you and your room.
For best result, place heater on the floor to create warming room convection and allow heater to run for
5-10 minutes to reach maximum heat output.
SET-UP
Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9 m) away from
any wall or combustible material.
DO NOT use on an unstable surface such as bedding or deep carpeting.
BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE TRIPPED OVER BY CHILDREN OR PETS.
MOVING THE HEATER
Turn off the heater.
Allow it to cool for ten minutes.
Unplug heater and move. This heater is equipped with a Cool Touch Handle for your convenience.
OPERATION
NOTE: The 360º Ceramic Surround Heater requires no assembly.
Fig. 1
NOTE: NEVER LEAVE AN OPERATING UNIT UNATTENDED
With the Power Knob or Power Button ( ) in the OFF (
position, plug the heater into a polarized 120V outlet.
DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET;
it will only fit one way.
)
The 360º Ceramic Surround Heater is versatile and designed for all
around heat output in 360° ( ) mode or directional heating when in
the 180° (
) mode.
To set 360° surround heating – on back of the heater, push the
directional lever in the UP position (Fig. 1)
Fig. 2
To set 180° directional heating – on back of the heater, push the
directional lever in the DOWN position (Fig. 2)
3
OPERATION (CONTINUED)
Model HZ-420 Series - 360º Ceramic Surround Heater Operation
The Power Knob is equipped with two (2) settings:
1)
Low (
) – this setting uses 900 watts of power
2)
High (
) – this setting uses 1500 watts of power
NOTE: Because the Low ( ) setting does not require as
much electricity to operate, it is more energy efficient and
may be a better option if you are concerned about saving
energy.
Turn heater on by turning the Power Knob to either Low
( ) or High ( ), the amber indicator light will come on.
To set the Thermostat, turn the Thermostat Control fully
clockwise to the highest ( ) setting.
Thermostat
Control
Power
Knob
When the room reaches a comfortable temperature, slowly
Power Light
turn the Thermostat Control counter-clockwise until both the
heating element and fan go off (the amber Power Light will
remain on). This is the point at which the Thermostat setting
equals the room temperature. At this setting, the Thermostat will automatically turn the heater back on and
then off as needed to maintain the selected temperature.
Turn the Power Knob to OFF (
) and unplug the heater when you are finished using it.
Model HZ-430 Series - EnergySmart™ 360º Ceramic Surround Heater Operation
Turn heater on by pressing Power Button ( ).
The heater will default to the Constant HI mode
and the Current Temp Indicator will display the
current room temperature.
The Energy Usage Indicator will display the power
consumption used by the heater.
• If HIGH, the heater is drawing 1500 watts to
quickly warm the room
• If LOW, the heater is drawing 900 watts
to slowly warm the room or maintain the
temperature
• If STAND BY, the heater is drawing no
power as the room has reached the Desired
Temperature
Model HZ-430
Energy Usage
Indicator
Current Temp
Indicator
Continuous
Heat Mode
EnergySmart™
Thermostat
Mode
Timer
Power Button
Power Light
4
OPERATION (CONTINUED)
To set the heater, the digital control is equipped with two (2) modes:
Constant Heat - there are two (2) heat settings
1.For Constant Low, press (
2.For Constant High, press (
); this setting uses 900 watts of power
); this setting uses 1500 watts of power
NOTE: Because the Low (
) setting does not require as much electricity to operate, it is more energy
efficient and may be a better option if you are concerned about saving energy.
EnergySmart™ Mode -
A smart thermostat that helps you save energy. Press SET to choose four (4) comfort settings of 65° (18°),
70° (21°), 75° (24°), 80° (27°). This is your desired room temperature. The EnergySmart™ thermostat
will automatically select the appropriate power level to best accommodate your Desired Temperature.
As the air temperature (Current Temp) in the room approaches the Desired Temperature, the heater will
automatically lower the power consumption to provide consistent warmth without wasting energy.
The Current Temp Indicator will display the current room temperature.
NOTE: In the EnergySmart™ mode, the Energy Usage Indicator will display what power consumption the
heater has automatically selected to efficiently meet your Desired Temperature.
• To override the EnergySmart™ function, turn the heater OFF ( ) or press SET to choose a
Constant Heat mode. The Energy Usage guide will indicate STAND BY when the heater has reached
the Desired Room Temperature. At this point, the heater is most efficient and is drawing only a few
watts of energy while in STAND BY mode.
• To set the Timer, press the (
) button to select 1, 2, 4, or 8 hour setting. The heater will run for
that chosen period in the selected mode, counting down the remaining time in the display bar and
automatically shut off after the desired time has passed.
Model HZ-440 Series - Digital 360º Surround Heater with Remote Operation
Turn heater on by pressing Power Button on ( )
and the heater will start at the HI Heat Level
Setting ( ). The Desired Temperature will flash
three times at a default of 75°F and the Current
Temperature in the room will then display in steady
red. Note: if the Current Temperature is higher
than 75°, the heater will remain off until the room
temperature falls below this setting or until the
Desired Temperature is changed.
• To set the Heat Level, press (
Model HZ-440
Current Temperature/
Desired Temperature
Display
Temperature
Set Button
):
1. For Low, (
); this setting uses
900 watts of power
2. For High, (
); this setting uses
1500 watts of power
Note: Because the Low (
) setting does
not require as much electricity to operate,
it is more energy efficient and may be a
better option if you are concerned about
saving energy.
Timer
Heat Level
Setting
Power Button
Power Light
5
OPERATION (CONTINUED)
• To set the thermostat, press the Temp Set button until Desired Temperature is reached. Note: the Desired
Temperature will flash three times and then Current Temperature in the room will display as a steady red.
• To constantly run the heater without a thermostat setting, press the Temp Set button until HI is
displayed in Temperature Display. In this mode, make sure to manually shut the heater OFF when
done using this appliance.
• To set the Timer, press the (
) button to select 1, 2, 4, or 8 hour setting. The heater will run for
that chosen period in the selected mode, counting down the remaining time in the display bar and
automatically shut off after the desired time has passed.
Remote Control
The Digital 360° Surround Heater can be completely controlled with the remote. Two AAA 1.5V batteries are
required (included). To install batteries:
• Remove the cover located on the back of the remote control.
• Insert two AAA 1.5V batteries, positioning them correctly (see instructions in the batteries compartment).
• Replace the cover.
Model HZ-440 Remote
Remote Control Operation
• Locate remote control packed in the top insert.
• Press (
) to turn heater on or off.
• Press (
) to choose LO (900W) or HI (1500W) Heat Level Setting.
• Press (
) to choose 1, 2, 4 or 8 hour setting.
• Press SET to choose a thermostat setting. Desired Temperature
will flash three times and then Current Temperature in the room
will display as a steady red.
Heat
Level
Setting
Power
Button
Temperature
Set Button
Timer
• Replace remote control in the holder on the side of the heater
when not in use.
SAFETY FEATURES
The 360º Ceramic Surround Heater is equipped with several devices and features for added protection:
• 360° SafetyTIP™ is an all-around tip-over switch that disables the heater if it is accidentally tipped
in any direction.
• A high temperature safety control prevents overheating.
• This heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater
should it operate at a higher than normal temperature.
• This heater was created using a high quality safety plastic.
CLEANING AND STORAGE
We recommend that the 360º Ceramic Surround Heater be cleaned at least once a month and before
off-season storage.
• Turn the heater OFF (
) or (
) and unplug it. Allow it to cool.
• Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES,
POLISHES OR ANY CHEMICAL SOLUTION.
• Before storing, clean the 360º Ceramic Surround Heater using the above-mentioned steps. Wrap the
cord around the unit. Place in its original box and store it in a cool, dry place.
6 • This heater does not disassemble.
TROUBLESHOOTING
If your 360º Ceramic Surround Heater shuts off unexpectedly or fails to operate, one of your heater safety
features may have been activated to prevent overheating.
• Be sure it is plugged in and that the electrical outlet is working.
• Check for any obstructions. If you find an obstruction, turn the heater OFF (
) or (
) and unplug it.
• Allow the heater to cool completely, then remove the obstruction. Wait at least 10 minutes, then re-plug
the heater in and follow the OPERATION instructions
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult an experienced radio/TV technician for help
Modifications not approved by the party responsible for compliance could void user’s authority to operate the
equipment pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interfere
HZ-420 Series, HZ-430 Series, HZ-440 Series
Unit dims
HZ-420 Series, HZ-440 Series 8.75” x 8.75” x 17.25” (22.2cm x 22.2cm x 43.8cm)
HZ-430 Series 8.75” x 8.75” x 18.5” (22.2cm x 22.2cm x 47cm)
Amps
12.5
Unit Voltage
120V, 60Hz
Max Watts
1500
Max BTUs
5118
Operation Cost*
To estimate the cost to operate this heater, multiple the watts used times .001 to convert into a kilowatts
measure and multiple by your local kilowatt electric rate for however long you run the heater. For
example, if your electric rate is $.1196** per kilowatt hour and you ran this heater in constant high mode
(1500 watts) for 4 hours, it would cost you $.71 cents to run the heater (1500 watts x 4 hours x.001) x
.1196kwp = .71 cents)
NOTE: Because the Low (
) or EnergySmart™ (HZ-430 Series) Settings do not require as much
electricity to operate, they are more energy efficient and may be better options if you are concerned about
the amperage draw on a circuit when the heater is on the High (
) setting.
*Calculation (Total Wattage x .001) x Cost per Kilowatt Hour = Cost to operate
**Average Retail Price of Electricity to Ultimate Customer by End-Use, US Energy Information Administration,
August 11, 2010
7
CONSUMER RELATIONS
Mail questions or comments to:
Kaz USA, Inc.
Consumer Relations Dept.
250 Turnpike Road
Southborough, MA 01772
Call us toll-free at: 1-800-477-0457
E-mail: consumerrelations@kaz.com
Or visit our website at: www.kaz.com
Please be sure to specify a model number.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE
YOUR WARRANTY. DO NOT RETURN THE HEATER TO THE ORIGINAL PLACE OF PURCHASE. DO NOT
ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND
CAUSE DAMAGE TO THE PRODUCT OR PERSONAL INJURY.
3 YEAR LIMITED WARRANTY
You should first read all instructions before
attempting to use this product.
A. This 3 year limited warranty applies to repair or
replacement of product found to be defective
in material or workmanship. This warranty
does not apply to damage resulting from
commercial, abusive, unreasonable use or
supplemental damage. Defects that are the
result of normal wear and tear will not be
considered manufacturing defects under this
warranty. KAZ USA, INC. IS NOT LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE. ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF
THIS WARRANTY. Some jurisdictions do not
allow the exclusion or limitation of incidental or
consequential damages or limitations on how
long an implied warranty lasts, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights,
and you also may have other rights which vary
from jurisdiction to jurisdiction. This warranty
applies only to the original purchaser of this
product from the original date of purchase.
B. At its option, Kaz USA, Inc. will repair or replace
this product if it is found to be defective in
material or workmanship.
8
C. This warranty does not cover damage resulting
from any unauthorized attempts to repair
or from any use not in accordance with the
instruction manual.
D. Return defective product to Kaz USA, Inc. with
a brief description of the problem. Include proof
of purchase and a $10 US/$15.50 CAN check
or money order for handling, return packing
and shipping charges. Please include your
name, address and a daytime phone number.
You must prepay shipping charges.
We suggest having tracking or delivery
confirmation. Send to:
In U.S.:
Kaz USA, Inc.
Attn: Returns Department
4755 Southpoint Drive
Memphis, TN 38118
USA
In Canada:
Kaz Canada, Inc.
Attn: Returns Department
510 Bronte Street South
Milton, ON L9T 2X6
Canada
Please go to www.kaz.com and register your
product under the Customer Care Center and
receive product information updates and new
promotional offers.
9
10
AVERTISSEMENT
CONSIGNES
DE SÉCURITÉ
IMPORTANTES
VOS RESPONSABILITÉS
11
12
GARDEZ CES
INSTRUCTIONS
25.
Fig. 1
Fig. 2
13
Bas (
2)
Haut (
Bouton
d’alimentation
14
):
15
Touche
d’alimentation
Minuteur
16
) ou (
17
SPÉCIFICATIONS DES PRODUITS
Modèle(s)
Dimensions
Tension
120 volts, 60 Hz
Puissance max. 1500 watts
BTU max.
5118
REMARQUE : EN CAS DE PROBLÈME, COMMUNIQUER AVEC LE SERVICE À LA CLIENTÈLE OU CONSULTER
LA GARANTIE. NE PAS RETOURNER L’APPAREIL AU LIEU D’ACHAT. NE PAS TENTER D’OUVRIR LE BOÎTIER
DU MOTEUR SOUS PEINE D’ANNULATION DE LA GARANTIE, D’ENDOMMAGEMENT DE L’APPAREIL OU DE
BLESSURES CORPORELLES.
18
19
20
IMPORTANTES
INSTRUCCIONES
DE SEGURIDAD
SUS RESPONSABILIDADES:
21
GUARDE ESTAS
INSTRUCCIONES
25.
Fig. 1
Fig. 2
23
2)
Alto (
) – este ajuste utiliza 1500 W de potencia
Control del
Termostato
24
Modelo HZ-440
Pantalla
Temperatura Actual/
Temperatura Deseada
25
Temporizador
)o(
PRODUCT SPECIFICATIONS
Modelo(s)
Series HZ-420, HZ-430
Series HZ-420 - 22.2 cm L x 22.2 cm A x 43.8 cm H (ensamblado)
Series HZ-430 - 22.2cm L x 22.2 cm A x 47 cm H (ensamblado)
Amperes
12.5
120V~, 60Hz
Watts Máximo
1500
BTUs Máximo
5118
SERVICIO AL CLIENTE
Envíe sus preguntas o comentarios a:
Kaz USA, Inc.
Consumer Relations Dept.
250 Turnpike Road
Southborough, MA 01772
NOTA: EN CASO DE PROBLEMA, CONTACTO SERVICO A LA CLIENTELA PRIMERO O CONSULTE LA GARANTÍA.
NO DEVUELVA EL RADIADOR AL COMERCIO DONDE LO COMPRÓ. NO INTENTE ABRIR LA CARCASA DEL MOTOR
USTED MISMO. SI LO HACE PUEDE ANULAR LA GARANTÍA Y PUEDE DA—AR EL APARATO O PROVOCAR
LESIONES PERSONALES.
28
©2011 Kaz USA, Inc.
All Rights Reserved.
Tous droits réservés.
Reservados todos los derechos.
P/N: 31IMZ440190
29
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising

Languages

Only pages of the document in English were displayed