Ninja BL494 User manual

®
ninjakitchen.com
1 877 646-5288
BL494
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL APPLIANCES,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR NINJA® KITCHEN SYSTEM
WITH AUTO-iQ Boost™.
POLARIZED PLUG
WARNING: To reduce the risk
of electric shock, this appliance has a
polarized plug (one blade is wider than
the other). This plug will fit into a
polarized outlet only one way. If the
plug does not fit fully into the outlet,
reverse the plug. If it still does not fit,
contact a qualified electrician to install
the proper outlet. DO NOT modify the
plug in any way.
WARNING:
3
4
5
6
7
Extension cords are not
recommended for use with this product.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1 WARNING: Remove utensils prior to
processing. Failure to remove may
cause the jar to be damaged or to
shatter which may cause personal
injury.
2
WARNING: The blade assemblies are
sharp, not locked in place and
removable, handle with care. When
handling the blade assemblies, always
hold by the shaft. Failure to do so will
result in a risk of laceration.
1
1-877-646-5288
8
9
WARNING: Stacked Blade Assembly
is sharp and not locked in place. If
using the pour spout, ensure the lid is
fully locked onto the pitcher. If pouring
with the lid removed, carefully remove
the Stacked Blade Assembly first,
holding it by the shaft. Failure to do so
will result in a risk of laceration.
WARNING: Chopping Blade Assembly
is sharp and not locked in place. Before
emptying contents carefully remove lid
and Chopping Blade Assembly, holding
it by the shaft. Failure to do so will
result in a risk of laceration.
CAUTION: Do not blend hot liquids,
doing so may cause excessive pressure
build-up, resulting in risk of the user
being burned.
CAUTION: We do not recommend
grinding in any of our Nutri Ninja® Cups.
CAUTION: Remove the Pro Extractor
Blades® Assembly from the Nutri Ninja
cup upon completion of blending. Do
not store ingredients before or after
blending them in the cup with the blade
assembly attached. Some foods may
contain active ingredients or release
gases which will expand if left in a
sealed container, resulting in excessive
pressure buildup that can pose a risk of
injury. For ingredient storage in the
cup, use only Sip & Seal® Lid to cover.
CAUTION: DO NOT process dry
ingredients without adding liquid to the
cup. This product is not intended for
dry blending.
To protect against electrical shock, do not
submerge the appliance or allow the power
cord to come into contact with water or any
other liquid.
23 DO NOT operate this appliance on or near
any hot surfaces (such as gas or electric
burner or in a heated oven).
24 The use of attachments or accessories
including canning jars, not recommended by
the manufacturer may result in fire, electric
shock or personal injury.
25 DO NOT remove the container from the
motor base while the appliance is in
operation.
26 To reduce the risk of injury, NEVER operate
the appliance without the lid in place; DO
NOT try to defeat the interlock mechanism;
make sure that the attachment is properly
installed before operating the appliance.
27 DO NOT expose containers to extreme
temperature changes.
28 DO NOT overfill.
29 DO NOT operate the appliance empty.
30 To reduce the risk of burns, always allow the
appliance to cool before taking off parts and
before cleaning.
31 In the event that the unit overloads, the
control panel lights will flash and the unit
will shut down. Unplug the appliance and let
it cool down for approximately 15 minutes
before using again.
32 THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use
this appliance for anything other than its
intended use. Do not use outdoors.
33 The maximum rating is based on the
Stacked Blade Assembly (pitcher) that drives
the greatest power and other recommended
attachments may draw significantly less
power or current.
SAVE THESE
INSTRUCTIONS
www.ninjakitchen.com
2
English
10 DO NOT allow the appliance to be used by
children. Close supervision is necessary
when used near children. This is not a toy.
11 Never leave an appliance unattended when
in use.
12 Appliance accessories are not intended to
be used in the microwave as it may result in
damage to the accessories.
13 Turn the appliance Off and remove the
power cord from the electrical outlet
when not in use, before assembling or
disassembling parts and before cleaning.
To unplug, grasp the plug and pull from the
electrical outlet. Never pull from the power
cord.
14 DO NOT abuse the power cord. Never carry
the appliance by the power cord or yank it
to disconnect from electrical outlet; instead
grasp the plug and pull to disconnect.
15 DO NOT operate any appliance with a
damaged cord or plug, or after the appliance
malfunctions, has been dropped or damaged
in any manner. This appliance has no
serviceable parts. Return the appliance to
SharkNinja Operating LLC for examination,
repair or adjustment.
16 DO NOT let the power cord hang over
the edge of table or counter or touch hot
surfaces such as the stove.
17 Always use appliance on a dry, level surface.
18 Keep hands, hair, clothing, as well as
utensils out of container while processing to
reduce the risk of severe injury to persons
or damage to the appliance. A scraper may
be used but only when the appliance is not
running.
19 Avoid contact with moving parts.
20 DO NOT attempt to sharpen blades.
21 DO NOT use the appliance if blade
assemblies are bent or damaged.
22 To reduce risk of injury, never place the
blade assemblies on the base without the
pitcher or Nutri Ninja cup properly attached.
FICHE POLARISÉE
AVERTISSEMENT :
4
5
6
AVERTISSEMENT :
7
AVERTISSEMENT :
1-877-646-5288
8
VEUILLEZ
CONSERVER CES
DIRECTIVES
www.ninjakitchen.com
4
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Para uso doméstico solamente
4
5
6
7
ADVERTENCIA:
ADVERTENCIA:
5
1-877-646-5288
8
CONSERVE ESTAS
INSTRUCCIONES
www.ninjakitchen.com
6
THIS BOOK COVERS MODEL NUMBER:
BL494
TECHNICAL SPECIFICATIONS
Voltage:
120V~, 60Hz.
Power:
1200 Watts
Pitcher Capacity:
72 oz. (9 cups, 2.1 L)
Max Liquid Capacity:
64 oz. (8 cups, 1.9 L)
Bowl Capacity:
40 oz. (5 cups, 1.18 L)
Nutri Ninja® Cup Capacity: 24 oz. (3 cups, 710 mL)
7
1-877-646-5288
Thank you for
purchasing the
Ninja® Kitchen
System with
Auto-iQ Boost™.
English
Contents
Getting to Know Your Ninja® Kitchen System with Auto-iQ Boost™�����������������������������������9
Before First Use ��������������������������������������������������������������������������������������������������������11
Assembly and Use of the Pitcher���������������������������������������������������������������������������������12
Assembly and Use of the Blend & Prep Bowl����������������������������������������������������������������14
Assembly and Use of the Nutri Ninja® Cups�����������������������������������������������������������������16
Care & Maintenance��������������������������������������������������������������������������������������������������17
Troubleshooting Guide������������������������������������������������������������������������������������������������18
Replacement Parts�����������������������������������������������������������������������������������������������������18
Warranty & Registration����������������������������������������������������������������������������������������������40
Table des matières
Comprendre votre système mélangeur NinjaMD avec l’Auto-iQ BoostMC ������������������������������19
Avant la première utilisation ..������������������������������������������������������������������������������������������������21
Assemblage et utilisation du pichet����������������������������������������������������������������������������������������22
Assemblage et utilisation du bol du robot culinaire�����������������������������������������������������������������24
Assemblage et utilisation du gobelet Nutri NinjaMD������������������������������������������������������������������26
Soins et entretien������������������������������������������������������������������������������������������������������������������27
Guide de dépannage�������������������������������������������������������������������������������������������������������������28
Pièces de remplacement�������������������������������������������������������������������������������������������������������28
Garantie et enregistrement����������������������������������������������������������������������������������������������������41
Gracias por haber
comprado sistema
de Cocina Ninja®
con Auto-iQ
BoostMR.
Índice
Partes de su Sistema de Cocina Ninja® con Auto-iQ BoostMR ���������������������������������������29
Antes de su Primera Utilización.���������������������������������������������������������������������������������31
Armado y uso de la licuadora �������������������������������������������������������������������������������������32
Armado y uso del tazón para procesar alimentos���������������������������������������������������������34
Armado y uso de las tazas Nutri Ninja®�����������������������������������������������������������������������36
Cuidado y mantenimiento�������������������������������������������������������������������������������������������37
Guía de diagnóstico de problemas������������������������������������������������������������������������������38
Partes de repuesto�����������������������������������������������������������������������������������������������������38
Garantía y registro������������������������������������������������������������������������������������������������������42
www.ninjakitchen.com
8
Getting To Know Your Ninja® Kitchen System with Auto-iQ Boost™
a
b
c
24 oz.
d
f
g
e
40 oz.
h
j
i
72 oz.
k
aRegular 24 oz. Nutri Ninja Cup (x2)
b Pro Extractor Blades® Assembly
c Sip & Seal® Lids (x2)
9
1-877-646-5288
d Blend & Prep Bowl
e Blend & Prep Bowl Lid
fChopping Blade Assembly
gDough Blade Assembly
h Pitcher
iPitcher Lid with Locking Handle
j Stacked Blade Assembly
k Motor Base
l Power Cord (not shown)
Ninja® Kitchen System with Auto-iQ Boost™ Features:
•
Ninja Blade Technology
•
BPA Free Pitcher, Nutri Ninja Cups, Blend & Prep Bowl and Lids
•
Drip-Free Pour Spout
•
Total Crushing® Technology
•
LED Control Panel with Timer
•
Sturdy, Non-Slip Base
•
Smart Lid technology for easy release
•
2 Manual Settings: Start/Stop, Pulse
•
5 Auto-iQ Settings: Puree, Mix/Dough, Extract, Smoothie, and Frozen Drink
•
Nutri Ninja Nutrient & Vitamin Extraction*
* Extract a Drink Containing Vitamins & Nutrients From Fruits & Veggies
www.ninjakitchen.com
10
English
The Ninja® Kitchen System with Auto-iQ Boost™ is a professional, high powered innovative tool with a sleek design and
outstanding performance, a true asset to any kitchen. The Ninja Kitchen System with Auto-iQ Boost features intelligent
programs that combine unique pulsing, blending and pausing patterns that do the work for you! Get great results every
time with no guesswork required! For best results, be sure to carefully read all the instructions contained in the manual
before using this appliance.
Before First Use
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
IMPORTANT: Make sure that the motor base
is plugged in for use.
IMPORTANT: Never add ingredients into the
container before placing the Blade Assembly
in first.
IMPORTANT: Blade Assemblies are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it
may result in damage to the accessories.
WARNING: Stacked
Blade Assembly is sharp
and not locked in place.
If using the pour spout,
ensure the lid is fully
locked onto the pitcher.
Failure to do so will result
in a risk of laceration.
WARNING:
Stacked Blade
Assembly is sharp
and not locked in
place. If pouring
with the lid removed,
carefully remove
the Stacked Blade
Assembly first, holding it by the shaft. Failure to
do so will result in a risk of laceration.
WARNING: Chopping
Blade Assembly is sharp
and not locked in place.
Before emptying contents
carefully remove lid and
Chopping Blade Assembly,
holding it by the shaft.
Failure to do so will result in a risk of laceration.
CAUTION: Do not immerse the motor base into
water or any other liquid.
1
Remove all packaging material and labels from the
appliance. Separate/remove all parts from each other.
2
Wash the lids, pitcher, bowl, Nutri Ninja® cups and
Blade Assemblies in warm, soapy water. When washing
the blade assemblies, use a dish-washing utensil with a
handle to avoid direct hand contact with blades.
CAUTION: Handle the Blade Assemblies with care
when washing, as the blades are very sharp.
11
1-877-646-5288
3
Handle blade assemblies with care to avoid contact
with sharp edges. Rinse and air dry thoroughly.
4
The pitcher, bowl, Nutri Ninja® cups, lids, and Blade
Assemblies, are all dishwasher safe. It is recommended
that the lids and blade assemblies be placed on the top
rack. Ensure that the blade assemblies are removed
from the containers before placing in the dishwasher.
5
Wipe the motor base clean with a damp cloth.
WARNING: Handle the Stacked Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or
to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
IMPORTANT: Make sure that the motor base is plugged in for use.
ASSEMBLY
Fig. 3a
OR
Fig. 5b
Fig. 1
Fig. 2
Fig. 3b
Fig. 4
Fig. 5a
It’s best to add the liquid ingredients first and then the dry ingredients.
1
2
3
4
5
6
Review warning and caution statements above before
proceeding to number 2.
Place the motor base on a clean, dry, level surface such
as a counter or table top. Press down on the motor
base to make sure that the Suction Cups adhere to the
counter or table top.
Align and lower the Pitcher onto the motor base.
(Fig. 1) Handle should be aligned slightly to the right of
the “LOCK” symbol on the motor base.
Rotate the pitcher clockwise until it clicks in place. As
the pitcher rotates, it will lower and the safety tabs on
the bottom of the pitcher will slide under the safety tabs
on the top of the motor base. (Fig. 2)
The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the drive gear inside the pitcher.
Ensure that the Stacked Blade Assembly is seated
properly and is standing upright. (Fig. 4)
NOTE: The Stacked Blade Assembly will fit loosely on
the drive gear.
7
8
9
Add the ingredients to the pitcher, making sure that
they do not exceed the highest measured marking line
on the side of the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is processing, open the pour spout cap
and pour the ingredients in through the opening.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed the
“MAX” liquid mark (64 oz.) on the Pitcher.
Holding the lid by the handle in the upright position,
place it on top of the Pitcher aligning the triangle
( ) located on the lid with the triangle ( ) located on
the Pitcher’s handle. (Fig. 5a) Press the handle down
until you hear a click. The triangles on the lid and
the blender handle MUST be aligned in order for the
blender to turn on. (Fig. 5b)
Plug the power cord into the electrical outlet. The
function lights will illuminate.
www.ninjakitchen.com
12
English
Assembly and Use of the Pitcher
Assembly and Use of the Pitcher - cont.
USE
REMOVAL
Fig. 6
Fig. 7
Fig. 8
Fig. 9
10 Review warning and caution statements on page 12
before proceeding.
15 Open the pour spout cap and use the spout to empty
liquid contents.
11 Select the speed or Auto-iQ program that best
suits your needs. The Auto-iQ program will stop the
appliance automatically at the end of the program.
(Fig. 6)
16 For thicker consistencies, first remove the lid by
pressing the release button and pulling the lid handle
up to a 90 degree angle to lift lid off the pitcher. Then,
carefully remove the Stacked Blade Assembly by the
top of the shaft. Place Stacked Blade Assembly away
from the work area to avoid accidental contact. Finally,
empty contents from the pitcher. (Fig. 8)
NOTE: Pulse ingredients for even chopping by holding
the Pulse button until your desired consistency is
reached.
12 To pause the appliance, press the selected speed or
Auto-iQ program a second time. When the program is
paused, the light on the program button will flash until
you press it again to resume the rest of the program.
13 When you have reached your desired consistency, stop
the appliance by pressing the START/STOP and wait
for the blade to stop turning.
14 Turn the pitcher counter clockwise to remove and then
lift off the base. (Fig. 7)
WARNING: Never insert your hands in the pitcher
as the Stacked Blade Assembly is sharp. Always
use a spatula to dislodge food that has stuck to
the sides of the pitcher.
13
1-877-646-5288
17 Make sure that the unit is unplugged when not in use.
18 To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you.
(Fig. 9)
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before emptying contents carefully
remove lid and Chopping Blade Assembly, holding it by the shaft. Failure to do will result in risk of
laceration.
WARNING: Remove utensils prior to processing. Failure to remove may cause the bowl to be damaged or to
shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
IMPORTANT: Make sure that the motor base is plugged in for use.
ASSEMBLY
Fig. 3a
Fig. 5b
OR
Fig. 1
Fig. 2
Fig. 3b
NOTE: Ninja® Kitchen System with Auto-iQ Boost™
can sense which jar is on the motor base. The function
lights will illuminate depending on which jar is placed
on the motor base.
1
2
Fig. 4
Align and lower the Blend & Prep Bowl onto the motor
base. (Fig. 1) Handle should be aligned slightly to the
right of the “LOCK” symbol on the motor base.
4
Rotate the bowl clockwise until it locks in place, you will
hear a click when the lock is engaged. (Fig. 2)
5
The bowl can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
6
Holding the desired blade assembly by the top of the
shaft, place it onto the drive gear inside the bowl.
Ensure that the blade assembly is seated properly and
is standing upright. (Fig. 4)
PULSE
BLEND
7
Add the ingredients to the bowl, making sure that they
do not exceed the highest measured marking line on
the side of the bowl.
8
Holding the lid by the handle in the upright position,
place it on top of the Blend & Prep Bowl aligning the
triangle ( ) located on the lid with the triangle
( ) located on the Blend & Prep Bowl handle. (Fig. 5a)
Press the handle down until you hear a click. The
triangles on the lid and the Blend & Prep Bowl handle
MUST be aligned in order for the blender to turn on.
(Fig. 5b)
Review warning and caution statements above before
proceeding to number 2.
Place the motor base on a clean, dry, level surface such
as a counter or table top. Press down on the motor
base to make sure that the suction cups adhere to the
counter or table top.
3
Fig. 5a
NOTE: The 64 oz. bowl is not intended for blending
drinks. Do not overfill.
9
Plug the power cord into the electrical outlet. The
function lights will illuminate.
NOTE: The blade will fit loosely on the drive gear.
www.ninjakitchen.com
14
English
Assembly and Use of the Blend & Prep Bowl
Assembly and Use of the Blend & Prep Bowl - cont.
USE
CHOPPING BLADE
ASSEMBLY
Fig. 1
Fig. 2
REMOVAL
Fig. 4
Fig. 3
USING THE CHOPPING BLADE ASSEMBLY
1
Review warning and caution statements on page 14 before
proceeding to number 2.
2 Place the motor base on a clean, dry, level surface such as a
counter or table top. Press down on the motor base to make
sure that the suction cups adhere to the counter or table top.
3 Secure the bowl onto the motor base.
4 Holding the Chopping Blade Assembly by the shaft, place it
onto the gear shaft inside the bowl. Ensure that the Chopping
Blade Assembly fits around the gear shaft and that it is
standing straight. (Fig. 1)
5 Add the ingredients and secure the bowl lid onto the bowl.
6 Plug the power cord into the electrical outlet. Once the bowl
is engaged, the programs available for that attachment
will illuminate. Select the speed or Auto-iQ™ program that
best suits your needs. Pulse ingredients for even chopping
by holding the Pulse button until your desired consistency is
reached.
NOTE: Please refer to “Speed Settings & Uses” chart for
suggested uses and speeds.
7 When you have reached your desired consistency, stop the
appliance by pressing the STOP/START button. Wait for
the Chopping Blade Assembly to stop turning. (Fig. 2)
8 To remove the lid, press the release button on the lid and pull
the lid handle up to a 90° angle. (Fig. 2)
9 Turn the bowl counter-clockwise and lift it to remove it from
the motor base. (Fig. 3)
10 To release the motor base from the counter or table top, place
your hands underneath both sides of the motor base and
gently pull the unit up and towards you. (Fig. 4)
15
1-877-646-5288
USE
DOUGH BLADE
ASSEMBLY
Fig. 5
USING THE DOUGH BLADE ASSEMBLY
1
Review warning and caution statements on page 14 before
proceeding to number 2.
2 Place the motor base on a clean, dry, level surface such as a
counter or table top. Press down on the motor base to make
sure that the suction cups adhere to the counter or table top.
3 Secure the bowl onto the motor base.
4 Holding the Dough Blade Assembly by the shaft, place it onto
the gear shaft inside the bowl. Ensure that the Dough Blade
Assembly fits around the gear shaft and that it is standing
straight. (Fig. 5)
5 Add the ingredients and secure the bowl lid onto the bowl.
6 Plug the power cord into the electrical outlet. Once the Bowl
is engaged, the programs available for that attachment will
illuminate. Select the MIX/DOUGH button and process until
ingredients come together to form a mass.
NOTE: Please refer to “Speed Settings & Uses” chart for
suggested uses and speeds.
7 Once finished making the dough, stop the appliance by
pressing the STOP/START button. Wait for the Dough
Blade Assembly to stop turning. (Fig. 2)
8 To remove the lid, press the release button on the lid and pull
the lid handle up to a 90° angle. (Fig. 2)
9 Turn the bowl counter-clockwise and lift it to remove it from
the motor base. (Fig. 3)
10 To release the motor base from the counter or table top, place
your hands underneath both sides of the motor base and
gently pull the unit up and towards you. (Fig. 4)
WARNING: Handle the Pro Extractor Blades Assembly with care, as the blades are sharp.
WARNING: Never leave the appliance unattended while in use.
WARNING: Remove utensils prior to processing. Failure to remove may cause the bowl to be damaged or to
shatter, which may cause personal injury.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
CAUTION: Remove the Pro Extractor Blades Assembly from the cup upon completion of blending. Do not
store ingredients before or after blending in the Nutri Ninja cup with the blade assembly attached. Some
foods may contain active ingredients or release gases which will expand if left in a sealed container,
resulting in excessive pressure buildup that can pose a risk of injury. For storage, only use Sip & Seal Lid
to cover.
IMPORTANT: Make sure that the motor base is plugged in for use.
ASSEMBLY
Fig. 1
1
2
3
4
5
6
7
Fig. 2
USE
REMOVAL
Fig. 3
Review warning and caution statements above before
proceeding to number 2.
Place the motor base on a clean, dry, level surface such as a
counter or table top. Press down on the motor base to make
sure that the suction cups adhere to the counter or table top.
Add ingredients to the Nutri Ninja cup.
Place the Pro Extractor Blades® onto the cup and tightly
screw it on clockwise until you have a good seal. (Fig. 1)
Turn the Nutri Ninja cup upside down and place it onto the
motor base, aligning the tabs on the cup with the motor base.
Rotate the Nutri Ninja cup clockwise until it locks in place, you
will hear a click when the lock is engaged. (Fig. 2)
Select the speed or Auto-iQ program that suits your needs.
(Fig. 3) The Auto-iQ program will stop the appliance
automatically at the end of the program.
To pause the appliance, press the selected speed or Auto-iQ
program a second time. When the program is paused, the
light on the program button will flash until you press it again
to resume the rest of the program.
Fig. 4
8
9
10
11
12
13
14
15
Fig. 5
Fig. 6
Turn the Nutri Ninja cup counter-clockwise and pull straight
up to remove. (Fig. 4, Fig. 5)
NOTE: Do not overfill! To avoid spilling, do not add ingredients
past the “Max Liquid” line.
Turn the cup upright and remove the Pro Extractor Blades by
twisting the Pro Extractor Blades counter clockwise. (Fig. 6)
Do not store blended contents with the Pro Extractor Blade
Assembly attached.
Place the Sip & Seal® lid onto the Nutri Ninja cup, twist to seal
and enjoy!
For storage, only use Sip & Seal lid to cover.
Be sure to store the Pro Extractor Blades Assembly attached
to an empty cup when not in use.
Make sure that the motor base is unplugged when not in use.
To release the motor base from the
counter or table top, place your hands
underneath both sides of the motor base
and gently pull the unit up and towards
you.
www.ninjakitchen.com
16
English
Assembly and Use of the Nutri Ninja® Cups
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before
inserting or removing any blade assembly and
before cleaning.
HOW TO STORE
1
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
1
Separate/remove all parts from each other.
2
Hand Washing: Wash the lids, pitcher, bowl, Nutri
Ninja cup, and blade assemblies in warm, soapy
water. When washing the blade assemblies, use a
dish-washing utensil with a handle to avoid direct hand
contact with blades. Handle blade assemblies with care
to avoid contact with sharp edges. Rinse and air dry
thoroughly.
Dishwasher: The containers, lids, blade assemblies
and attachments are all dishwasher safe. The lids
and blade assemblies are top rack dishwasher safe.
Ensure that the blade assemblies are removed from the
containers before placing in the dishwasher.
WARNING: Handle the Blade Assemblies with
care when washing, as the blades are sharp.
Contact with the blades’ edges can result in
laceration.
3
Wipe the motor base clean with a damp cloth.
Please call customer service if any servicing needs to
be performed on the appliance at 1-877-646-5288.
17
1-877-646-5288
Store the Ninja® Kitchen System with Auto-iQ
Boost™ upright with the blade assembly inside the
corresponding container with the lid secured on top.
Do not place anything on top. Store the rest of the
attachments in a safe place where they will not be
damaged and won’t cause harm. Wrap the power cord
around the cord wrap on the back of the motor base.
NOTE: Do not store blended or unblended
ingredients in the Nutri Ninja Cup with the blade
assembly attached.
RESETTING THE MOTOR THERMOSTAT
The Ninja Kitchen System with Auto-iQ Boost features
a unique safety system which prevents damage to the
unit’s motor and drive system should you inadvertently
overload your appliance. If the appliance is being
overloaded, the motor will stop. Allow the
appliance to cool for approximately 15 minutes.
To reset the appliance, follow the resetting procedure
below:
1
Unplug the appliance from the electrical outlet.
2
Remove and empty the container and ensure that no
food is jamming the Blade Assembly or attachments.
3
Allow the appliance to cool for approximately 15
minutes.
4
Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5
Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.
English
Troubleshooting Guide
Unit doesn’t turn on:
•
Make sure the unit is plugged in.
•Insert and rotate cup clockwise in the base until it clicks into place. Display should turn on.
Unit doesn’t turn off:
•
Remove cup from base by rotating cup counter-clockwise and lifting out. Display should turn off. Unplug the power cord
from the outlet.
Lid/blade assembly hard to assemble:
•
Set the cup on a level surface. Place the lid or blade assembly on the top of the cup and align the threads so that the
lid/blades sit flat on the cup. Twist clockwise so that the lid/blades evenly align to the cup until you have a tight seal.
Food is not evenly chopped:
•
For best results when chopping, make sure all ingredients are as dry as possible. Cut pieces down to even sizes, and
reduce the amount of food in the cup. Use the Auto-iQ™ CHOP button for best results.
Doesn’t mix well, food gets stuck:
•
Using the Auto-iQ programs is the easiest way to achieve great results. The pulses and pauses allow the food to settle
toward the blade. If food is routinely getting stuck, adding some liquid will usually help.
•When packing the cups, start with fresh items, then add liquids, powders/dry ingredients, and finally frozen items or
ice.
Unit moves on the counter while blending:
•Make sure the surface as well as the feet of the unit are clean and dry.
Unit is difficult to remove from the counter for storage:
•To release the motor base from the counter or tabletop, place your hands underneath both sides of the motor base and
gently pull the unit up and toward you.
Display shows “--”:
•Unplug unit and wait 30 minutes before running any program.
Replacement Parts
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, please visit our website: www.ninjakitchen.com
or feel free to contact customer service: 1-877-646-5288.
www.ninjakitchen.com
18
a
b
c
24 oz.
d
f
g
e
40 oz.
h
j
i
72 oz.
k
19
1-877-646-5288
Technologie Ninja
•
•
•
Technologie Total CrushingMD
•
•
•
•
•
5 réglages Auto-iQ : Puree, Mix/Dough, Extract, Smoothie, et Frozen Drink
•
www.ninjakitchen.com
20
1
2
3
4
5
21
1-877-646-5288
MONTAGE
Fig. 3a
OU
Fig. 5b
Fig. 1
1
2
3
4
5
6
Fig. 2
Fig. 3b
Fig. 4
7
8
9
Fig. 5a
www.ninjakitchen.com
22
Fig. 6
DÉMONTAGE
Fig. 7
23
1-877-646-5288
Fig. 8
Fig. 9
ASSEMBLAGE
Fig. 3a
Fig. 5b
OU
Fig. 1
Fig. 2
Fig. 3b
Fig. 4
7
8
9
Fig. 5a
PULSE
BLEND
www.ninjakitchen.com
24
DÉMONTAGE
JEU DE LAMES
À HACHER
Fig. 1
Fig. 2
Fig. 4
Fig. 3
UTILISATION DU JEU DE LAMES DE HACHAGE
1
1-877-646-5288
UTILISATION
JEU DE LAMES
À PÉTRIR
Fig. 5
UTILISATION DU JEU DE LAMES À PÉTRIR
1
ASSEMBLAGE
Fig. 1
1
2
3
4
5
6
7
Fig. 2
UTILISATION
DÉMONTAGE
Fig. 3
Fig. 4
8
9
10
11
12
13
14
15
Fig. 5
Fig. 6
26
COMMENT RANGER
1
2
3
27
1-877-646-5288
2
3
4
5
www.ninjakitchen.com
28
Sistema de Cocina Ninja® con Auto-iQ BoostMR
a
b
c
24 oz.
d
f
g
e
40 oz.
h
j
i
72 oz.
k
29
1-877-646-5288
•
•
•
Tecnología Total CrushingMR
•
•
•
•
2 velocidades: Start/Stop, Pulse
•
5 ajustes con Auto-iQ: Puree, Mix/Dough, Extract, Smoothie, y Frozen Drink
•
www.ninjakitchen.com
30
2
31
1-877-646-5288
3
4
5
Fig. 3a
O
Fig. 5b
Fig. 1
Fig. 2
Fig. 3b
Fig. 4
Fig. 5a
3
4
5
6
7
8
9
www.ninjakitchen.com
32
USO
Fig. 6
Fig. 7
33
1-877-646-5288
Fig. 8
Fig. 9
ARMADO
Fig. 3a
Fig. 5b
O
Fig. 1
Fig. 2
Fig. 3b
3
Fig. 4
5
6
PULSE
BLEND
8
4
Fig. 5a
www.ninjakitchen.com
34
LA CUCHILLA
PARA PICAR
Fig. 1
Fig. 2
Fig. 4
Fig. 3
USO DE LA CUCHILLA PARA PICAR
1
35
1-877-646-5288
USO
ACCESORIO PARA
AMASAR
Fig. 5
USO DEL ACCESORIO PARA AMASAR
1
ARMADO
USO
8
9
10
11
12
13
14
15
www.ninjakitchen.com
36
ALMACENAMIENTO
1
2
3
37
1-877-646-5288
2
3
4
5
www.ninjakitchen.com
38
Notes / Remarques / Notas
39
1-877-646-5288
English
ONE (1) YEAR LIMITED WARRANTY
SharkNinja Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1)
year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and
exceptions.
The liability of SharkNinja Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.
This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or
used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or
damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused by
or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been
performed by a repair person not authorized by SharkNinja Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the Limited Warranty period,
you may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For Customer Service
support, call 1-877-646-5288 or visit our website www.ninjakitchen.com.
If the appliance is found by SharkNinja Operating LLC to be defective, in SharkNinja Operating LLC’s sole discretion, we
will repair or replace it free of charge. Proof of purchase date and a check made payable to SharkNinja Operating LLC in the
amount of $19.95 to cover the cost of return shipping and handling must be included.*
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional
warranties. The responsibility of SharkNinja Operating LLC if any, is limited to the specific obligations expressly assumed
by it under the terms of this Limited Warranty. In no event is SharkNinja Operating LLC liable for incidental or consequential
damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or from
province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and
to attach tag to item before packing with your name, complete address and phone number with a note giving
purchase information, model number and what you believe is the problem with the item. We recommend you insure
the package (as damage in shipping is not covered by your Limited Warranty). Mark the outside of your package
“ATTENTION CUSTOMER SERVICE”.
PRODUCT REGISTRATION
Please visit www.registeryourninja.com or call 1-877-646-5288 to register your new Ninja® product within ten (10) days
of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and
address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you
acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
www.ninjakitchen.com
40
1-877-646-5288
42
SharkNinja Operating LLC
US:
Newton, MA 02459
CAN:
Ville St-Laurent, QC H4S 1A7
1-877-646-5288
www.ninjakitchen.com
Copyright / Droit d’auteur / Derechos reservados © SharkNinja Operating LLC 2016
Ninja, Nutri Ninja, Pro Extractor Blades, Sip & Seal and Total Crushing are registered trademarks of SharkNinja Operating LLC.
Auto-iQ Boost is a trademarks of SharkNinja Operating LLC.
Ninja, Nutri Ninja, Pro Extractor Blades, Sip & Seal et Total Crushing sont des marques déposées de SharkNinja Operating LLC.
Auto-iQ Boost est un marque commerciale de SharkNinja Operating LLC.
Ninja, Nutri Ninja, Pro Extractor Blades, Sip & Seal y Total Crushing son marcas registradas de SharkNinja Operating LLC.
Auto-iQ Boost es un marcas comerciales de SharkNinja Operating LLC.
For SharkNinja U.S. Patent information visit sharkninja.com/USPatents.
Pour des renseignements sur les brevets de SharkNinja aux É.-U., veuillez visiter sharkninja.com/USPatents.
Para obtener información acerca de las patentes en EE.UU. de SharkNinja, visite http://www.sharkninja.com/USPatents.
Illustrations may differ from actual product. We are constantly striving to improve our products, therefore the specifications contained herein
are subject to change without notice.
Les illustrations peuvent être différentes des produits réels. Nous nous efforçons sans cesse d’améliorer nos produits et, de ce fait, les
spécifications décrites dans ce guide sont sujettes à des changements sans préavis.
El dibujo puede no ser igual al producto real. Nosotros nos esforzamos constantemente en mejorar nuestros productos, por lo tanto las
especificaciones aquí indicadas pueden cambiar sin previo aviso.
Printed in China / Imprimé en Chine / Impreso en China
BL494_30_160823.4