- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- Hayward
- SharkVac XL
- Owner's manual
advertisement
▼
Scroll to page 2
of 65
™ ™ SharkVAC XL / e.VAC PRO by Owner’s Manual ™ ™ SharkVAC XL / e.VAC PRO par ™ SharkVAC XL / e.VAC PRO de Manual del propietario ISRC9740XLN Rev C ™ ™ SharkVAC XL / e.VAC PRO by Owner’s Manual Contents Warnings ........................... 3 Information ........................ 5 Operating Instructions ........... 7 Maintenance ....................... 11 Troubleshooting ................... 17 Warranty Registration .............. 22 IMPORTANT SAFETY INSTRUCTIONS Basic safety precautions should always be followed, including the following: Failure to follow instructions can cause severe injury and/or death. This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for one of the following signal words and be alert to the potential for personal injury. WARNING warns about hazards that could cause serious personal injury, death or major property damage and if ignored presents a potential hazard. CAUTION warns about hazards that will or can cause minor or moderate personal injury and/or property damage and if ignored presents a potential hazard. It can also make consumers aware of actions that are unpredictable and unsafe. The NOTICE label indicates special instructions that areProducts important but not related to hazards. Hayward Pool 620 Division Street, Elizabeth, NJ 07207 Phone: (908) 351.5400 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 2 WARNING – Read and follow all instructions in this owner’s manual and on the equipment. Failure to follow instructions can cause severe injury and/or death. WARNING – Suction in suction outlets and/or suction outlet covers which are, damaged, broken, cracked, missing, or unsecured can cause severe injury and/or death due to the following entrapment hazards: Hair Entrapment- Hair can become entangled in suction outlet cover. Limb Entrapment- A limb inserted into an opening of a suction outlet sump or suction outlet cover that is damaged, broken, cracked, missing, or not securely attached can result in a mechanical bind or swelling of the limb. Body Suction Entrapment- A negative pressure applied to a large portion of the body or limbs can result in an entrapment. Evisceration/ Disembowelment - A negative pressure applied directly to the intestines through an unprotected suction outlet sump or suction outlet cover which is, damaged, broken, cracked, missing, or unsecured can result in evisceration/ disembowelment. Mechanical Entrapment- There is potential for jewelry, swimsuit, hair decorations, finger, toe or knuckle to be caught in an opening of a suction outlet cover resulting in mechanical entrapment. WARNING o o o o o o o o – To Reduce the risk of Entrapment Hazards: When outlets are small enough to be blocked by a person, a minimum of two functioning suction outlets per pump must be installed. Suction outlets in the same plane (i.e. floor or wall), must be installed a minimum of three feet (3’) [1 meter] apart, as measured from near point to near point. Dual suction fittings shall be placed in such locations and distances to avoid “dual blockage” by a user. Dual suction fittings shall not be located on seating areas or on the backrest for such seating areas. The maximum system flow rate shall not exceed the flow rating of as listed on Table 1. Never use Pool or Spa if any suction outlet component is damaged, broken, cracked, missing, or not securely attached. Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately. In addition two or more suction outlets per pump installed in accordance with latest ASME, APSP Standards and CPSC guidelines, follow all National, State, and Local codes applicable. Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended. WARNING – Failure to remove pressure test plugs and/or plugs used in winterization of the pool/spa from the suction outlets can result in an increase potential for suction entrapment as described above. WARNING – Failure to keep suction outlet components clear of debris, such as leaves, dirt, hair, paper and other material can result in an increase potential for suction entrapment as described above. WARNING – Suction outlet components have a finite life, the cover/grate should be inspected frequently and replaced at least every ten years or if found to be damaged, broken, cracked, missing, or not securely attached. CAUTION – Components such as the filtration system, pumps and heater must be positioned so as to prevent their being used as means of access to the pool by young children. WARNING – Never operate or test the circulation system at more than 50 PSI. WARNING – Never change the filter control valve position while the pump is running. WARNING – To reduce risk of injury, do not permit children to use or climb on this product. Closely supervise children at all times. Components such as the filtration system, pumps, and heaters must be positioned to prevent children from using them as a means of access to the pool. WARNING – Hazardous Pressure. Pool and spa water circulation systems operate under hazardous pressure during start up, normal operation, and after pump shut off. Stand clear of circulation system equipment during pump start up. Failure to follow safety and operation instructions could result in violent separation of the pump housing and cover, and/or filter housing and clamp due to pressure in the system, which could cause property damage, severe personal injury, or death. Before servicing pool and spa water circulation system, all system and pump controls must be in off position and filter manual air relief valve must be in open position. Before starting system pump, all system valves must be set in a position to allow system water to return back to the pool. Do not change filter control valve position while system pump is running. Before starting system pump, fully open filter manual air relief valve. Do not close filter manual air relief valve until a steady stream of water (not air or air and water) is discharged. WARNING – Separation Hazard. Failure to follow safety and operation instructions could result in violent separation of pump and/or filter components. Strainer cover must be properly secured to pump housing with strainer cover lock ring. Before servicing pool and spa circulation system, filters manual air relief valve must be in open position. Do not operate pool and spa circulation system if a system component is not assembled properly, damaged, or missing. Do not operate pool and spa circulation system unless filter manual air relief valve body is in locked position in filter upper body. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 3 WARNING – Risk of Electric Shock. All electrical wiring MUST be in conformance with applicable local codes, regulations, and the National Electric Code (NEC). Hazardous voltage can shock, burn, and cause death or serious property damage. To reduce the risk of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide a properly located electrical receptacle. Before working on any electrical equipment, turn off power supply to the equipment. WARNING – To reduce the risk of electric shock replace damaged wiring immediately. Locate conduit to prevent abuse from lawn mowers, hedge trimmers and other equipment. WARNING – Electrical ground all electrical equipment before connecting to electrical power supply. Failure to ground all electrical equipment can cause serious or fatal electrical shock hazard. WARNING – Do NOT ground to a gas supply line. WARNING – To avoid dangerous or fatal electrical shock, turn OFF power to all electrical equipment before working on electrical connections. WARNING – Failure to bond all electrical equipment to pool structure will increase risk for electrocution and could result in injury or death. To reduce the risk of electric shock, see installation instructions and consult a professional electrician on how to bond all electrical equipment. Also, contact a licensed electrician for information on local electrical codes for bonding requirements. Notes to electrician: Use a solid copper conductor, size 8 or larger. Run a continuous wire from external bonding lug to reinforcing rod or mesh. Connect a No. 8 AWG (8.4 mm2) [No. 6 AWG (13.3 mm2) for Canada] solid copper bonding wire to the pressure wire connector provided on the electrical equipment and to all metal parts of swimming pool, spa, or hot tub, and metal piping (except gas piping), and conduit within 5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub. IMPORTANT - Reference NEC codes for all wiring standards including, but not limited to, grounding, bonding and other general wiring procedures. WARNING – Risk of Electric Shock. Connect only to a branch circuit protected by a ground-fault circuit-interrupter (GFCI). Contact a qualified electrician if you cannot verify that the circuit is protected by a GFCI. WARNING – Risk of Electric Shock. The electrical equipment must be connected only to a supply circuit that is protected by a ground-fault circuit-interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the electrical equipment without the test button being pushed, a ground current is flowing, indicating the possibility of an electrical shock. Do not use this electrical equipment. Disconnect the electrical equipment and have the problem corrected by a qualified service representative before using. CAUTION – This pump is intended for use with permanently-installed pools and may be used with hot tubs and spas if so marked. Do not use with storable pools. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. SAVE THESE INSTRUCTIONS Hayward® Pool Products Limited Warranty To original purchasers of this equipment, Hayward Pool Products, Inc. warrants its cleaners to be free from defects in materials and workmanship for a period of TWO (2) years from the date of purchase, when used in single family residential applications. The limited warranty excludes damage from freezing, negligence, improper installation, improper use or care or any Acts of God. Parts that fail or become defective during the warranty period shall be repaired or replaced, at our option, within 90 days of the receipt of defective product, barring unforeseen delays, without charge. Proof of purchase is required for warranty service. In the event proof of purchase is not available, the manufacturing date of the product will be the sole determination of the purchase date. To obtain warranty service, please contact the place of purchase or the nearest Hayward Authorized Service Center. For assistance on your nearest Hayward Authorized Service Center please visit us at www.hayward.com. Hayward shall not be responsible for cartage, removal, repair or installation labor or any other such costs incurred in obtaining warranty replacements or repair. The Hayward Pool products warranty does not apply to components manufactured by others. For such products, the warranty established by the respective manufacturer will apply. The express limited warranty above constitutes the entire warranty of Hayward Pool Products with respect to its’ pool products and is in lieu of all other warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose. In no event shall Hayward Pool products be responsible for any consequential, special or incidental damages of any nature. Some states do not allow a limitation on how long an implied warranty lasts, or the exclusion of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. *Supersedes all previous publications. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Hayward Pool Products 620 Division Street Elizabeth, NJ 07207 4 CONSUMER INFORMATION AND SAFETY DANGER Risk of electrical shock or electrocution The electrical supply to this product must be installed in accordance with all applicable local codes and ordinances. Improper installation will create an electrical hazard which could result in death or serious injury to pool users or others due to electrical shock, and may also cause damage to property. WARNING Do not play with cleaner or cable or apply to body. Can trap or tear hair or body parts. Cable can trip or entangle swimmers, which could result in drowning. CAUTION Before installing the cleaner, understand cleaner coverage. The cleaner was not designed to automatically clean steps or to work under a solar cover. It was also not designed to do initial cleanup for a new pool installation. OPERATING THE CLEANER WARNING A Ground Fault Current Interrupter (GFCI –USA) must be installed to protect your electrical outlet and to prevent any possible electric shock. Failure to do so could create an electrical hazard which could result in death or serious injury to pool users or others due to electrical shock and may also cause damage to property. CAUTION DO NOT switch the pool cleaner to “ON” if it is not immersed in the water. Operating the cleaner out of the water may cause severe damage and will result in loss of warranty. Always remember to turn off the power supply “OFF” and unplug it from the power outlet before removing the cleaner from the pool. WARNING It is mandatory to allow a safety distance between the power supply and the pool as required by the current installation standard (11.5 feet minimum or 3.5 meters). USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 5 WARNING - READ THESE IMPORTANT OPERATING TIPS BEFORE USING YOUR UNIT! Dear Hayward Robotic Cleaner Owner: Thank you for choosing Hayward. In order to achieve optimal performance, please read and follow these steps: 1. Cleaner filter cartridges should be thoroughly cleaned after each use or as often as needed to ensure cleaner's optimal performance. (see the Maintenance section for filter cleaning instructions) 2. Before using your cleaner and especially when opening the pool for the first time remove larger items such as toys, large leaves, or other debris from the pool that may diminish the cleaner's performance. Clean filter frequently when pool is excessively dirty. 3. For the first use, run cleaner for the full cycle (3 hours) to ensure a clean pool and give you a full understanding of the cleaner's capabilities. 4. Cleaner may periodically go to the wall but not necessarily climb to the vertical position. This is a normal part of the programmed cycle. 5. Cleaner may stop in the middle of the pool and reverse during cleaning cycle. This is a normal part of the programmed cycle. 6. DO NOT start cleaner out of the water. Power button should only be switched to "ON" position when unit is fully submerged. The unit will automatically shut off, but it is best to put power switch in "OFF" position when unit completes cleaning. 7. Only plug into a GFCI (Ground Fault Circuit Interrupter) protected 110-120 volt AC outlet. 8. Place the cleaner power supply so that it is at a minimum distance of 11.5 feet (3.5 meters) from the pool edge. The length of the standard cleaner cable is 60 feet (18.29 meters). 9. Depending on the size and shape of your pool the entire length of the floating cable may not be necessary. The floating cable should reach from the cleaner power supply to the furthest point in the pool, plus the depth at the deep end of the pool. To reduce cable tangling any excess cable should be coiled and placed next to the power supply. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 6 GENERAL OPERATING INSTRUCTIONS Take a moment to get familiar with the cleaner using the figure 3. Throughout this manual reference to this figure is made when referring to different components of the cleaner. Remove the cleaner by placing the carton down and removing it from the box as shown. On models which include a caddy cart the cleaner and the Power Supply are pre-mounted to the cart. See the figure 4 for Caddy Cart. 1. Select the nearest GFCI (Ground Fault Circuit Interrupter) protected 110-120 volt AC outlet. 2. Place the cleaner power supply so that it is at a minimum distance of 11.5 feet (3.5 meters) from the pool edge. The length of the standard cleaner cable is 60 feet (18.29 meters). 3. Stretch out the floating cable along the pool deck to remove any twisting the cord has from storage and measure out the approximate amount of cleaner cord needed for pool coverage. 4. Connect the floating cable to the power supply. Use only the original Power Supply manufactured by Hayward. 4. Place the cleaner in the pool. It will slowly sink to the bottom of the pool as the air inside is released. 5. Connect the power supply to the protected outlet and switch it on. The cleaner will perform a selfdiagnostics routine before starting the cleaning cycle for several minutes. Notice: To reduce risk of injury and prevent damage to the cleaner the start up sequence the cleaner has been equipped with an out of water sensor. Should the cleaner sense that it is not in the water it will power itself down. To reset the cycle switch off the power supply for 10 seconds and restart. 6. The cleaner will automatically shut off after 3 hours for a full cleaning cycle. If your pool is cleaned in less time than 3 hours, you may shut the cleaner off manually by switching the power supply to the off position. Should a second cleaning cycle be required, switch OFF the power supply for 10 seconds and restart. 7. After the pool has been cleaned, switch OFF the power supply before removing the cleaner from the pool. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 7 8. Remove the cleaner from the water at the shallow end of the pool by gently pulling the cable until the cleaner reaches the surface. Then lift it out of the water using the handle, NOT the cable. 9. If the supply cord is damaged it must be replaced by the manufacturer, service agent, or similarly qualified persons in order to avoid a hazard. 10. All electrical connections must be done by a qualified electrician according to local electrical standard (see p16). Operating the cleaner using an aftermarket timer If you are using an aftermarket timer to turn your cleaner on please follow these instructions: 1. Plug the aftermarket timer into the nearest GFCI (Ground Fault Circuit Interrupter) protected 110120 volt AC outlet and then plug the power supply into the timer. 2. The cleaner operates on a 3 hour cycle so set the timer duration for 3 hours or more. If you set the timer duration for less than 3 hours the cleaner will only operate for the period of time you set. If you set the timer duration for longer than 3 hours the cleaner will stop automatically at the end of its 3 hour cycle. Should a second cleaning cycle be required, switch OFF the power supply for 10 seconds and restart. CAUTION: When removing cleaner from the pool do NOT reel it around your arm. The cleaner is heavy and may cause someone to lose their balance and fall into the pool. To avoid falling into the pool, gently reel the cable in hand-over-hand from the shallow end of the pool. DO NOT ENTER THE SWIMMING POOL WHEN THE CLEANER IS OPERATING. Optimum operating water temperature range for the cleaner is 50ºF - 100ºF (10ºC - 35ºC). Remove the cleaner from the pool, empty the filter bucket and clean filters after each use. Keeping the cleaner permanently in the pool may result in additional service requirements. (see maintenance section for cleaning instructions) Store the cleaner in a shaded area. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 8 1. Power Supply 8. Dome Assembly 2. On/Off Switch 9. Side Panel 3. Floating Cable 10. Wheel 4. Handle 11. Float Assembly 5. Filter Cartridge 12. Sealed Motor Unit 6. Filter Bucket 13. Wheel Brush and Tube 7. Filter Door 14. Drive Track USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 9 CADDY CART INSTRUCTIONS - SEE DIAGRAM Caddy Cart will come partially assembled in the carton less the handle & tube. (1 & 3) Insert the tube into base (5) & insert the screw (4) securing it with the nut (2) Insert the handle into the top of the tube & insert the screw (4) securing it with the nut (2) USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 10 MAINTENANCE Clean the filter cartridge after each use: 1. Open the cleaner by pressing the lid button and lifting up the dome cover. 2. Remove the easy access filter bucket assembly by lifting it up out of the cleaner with both hands from each side. 3. Flip the bucket assembly over to remove the debris and then rinse with a garden hose to remove small particles. 4. Filter cartridges do not need to be removed to clean. Fig. 6 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 11 5. Remove the filter cartridges: a. Unsnap and lift up both filter door latches. b. Pull out the filter cartridges. Using a garden hose with a spray nozzle, wash the filter elements to remove debris. Hold the filter elements as shown to allow the debris to fall out. Filter cleaning solution can be used to remove excessive dirt and/or sand. The cleaner your filter is the more effective the cleaning will be. Fig. 7 c. Wash the entire filter bucket assembly. (Previously shown). d. Place the filter cartridges back into the filter bucket assembly with the center frame reinforcements facing inward. Fig. 8 e. Snap the filter door latches into place. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 12 6. Return the filter bucket assembly into the cleaner using the diagram shown to determine the front and back. 7. Close the dome and press the lid button to snap dome into place. Periodic Cleaning of Moving Parts WARNING: Disconnect the power supply from electrical outlet before cleaning moving parts. Inspect the venturi to ensure that no debris or hair has clogged the impeller. The impeller can be cleaned by spraying it with a garden hose. Spray water using a garden hose around the float box assembly to remove any sand or debris to ensure free movement when changing float position. Remove any debris that has accumulated between the tracks and wheels. Storage When unit is out of the water, store the cleaner in a dry, shady location at temperatures between 40F - 115F (4°C-46°C). Cable Care With continued use, the cable may become coiled (like a telephone cord). To correct this, stretching the cord out in the sun should remove any cord twists. IMPORTANT: The cable should be checked periodically for any external damage. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 13 Back side wall climbing Float Position WALL CLIMBING FEATURE SharkVac-XL is equipped with patent pending “movable flotation technology”. Each float position (I, II, and III) will provide different wall climbing action. Float position “I” is the default position locating the float in the middle of the cleaner and will provide the best cleaning behavior for most swimming pools. Float position “II” will provide an additional angle in the movement where the cleaner will travel along the water line or pool wall faster and benefit cleaning coverage. Float position “III” will provides a reduced angle in the movement where the cleaner will spend more time scrubbing the pool wall along the water line. This float position will aid the wall climbing feature in pools with slick surfaces such as tile and fiberglass. Method of selection: Position may be set while the cover is closed using the slide handle, or while the cover is opened by moving the float box to the preferred location. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 14 OUT OF WATER SENSOR To better protect the cleaner from damage, it will sense when being asked to turn on when not safely in water, or leaves the water during operation. Out of water at start up Out of water at start up means that the cleaner has been powered on, either by the user connecting the power supply to the protected outlet and switching it on or by being connected to a timer that switches on the power supply, before the cleaner has been placed in the water. If the cleaner senses that it is not in the water the unit will power itself down. To reset the cycle, switch off the power supply for 10 seconds and restart. Out of water during operation Out of water during operation refers to the cleaner leaving or being removed from the water while in normal operation cycle. If the cleaner senses that it is no longer in the water, the unit will attempt to re-enter the water by reversing its current direction. If the cleaner is not submerged within ninety (90) seconds of leaving the water the unit will power itself down. To reset the cycle, switch off the power supply for 10 seconds and restart. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 15 IMPORTANT TIPS Do not drop or throw the cleaner into pool. Place cleaner away from the pool wall but do not throw the cleaner in the pool. Cleaning the filter cartridges after every use maximizes the unit's performance. Replace worn brushes and foam rollers. To avoid clogging the cleaner's filter elements, be sure all chemical powders are fully dissolved before operating the cleaner. In a pool with high calcium content, more frequent cleaning of the filter cartridges is recommended. Save the original carton for extended storage or shipping requirements should your cleaner require dealer service. The sealed Motor Unit and the Power Supply contain no user-serviceable parts. Opening them will automatically VOID your warranty. Remove items such as thermometer, toys and the like from the pool before operating the unit. Such items can jam the cleaner and cause damage to the unit and/or your pool. The filter bucket is designed to be cleaned with the filters installed for normal clean up. For deep cleaning, the user can remove each filter cartridge and clean separately. During the normal operating cycle of the cleaner, the handle side of the unit will rise from the pool bottom to allow the unit to clear obstacles, such as elevated main drains and stair steps. For cleaners used in areas that have a lot of sand the cleaner may need to be rinsed with water at all flapper (filter bucket's flapper is at intake port) areas, and may need rinsing at the dome push button to allow free operation. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 16 TROUBLESHOOTING If the cleaner fails to pick up fine or heavy debris: It may be clogged. Clean the filter. A filter cleaning solution can be used to remove excessive dirt and/or sand. If the cleaner starts working momentarily but then stops working: Impeller may be clogged or jammed with debris, check and clean if necessary following the instructions in the maintenance section. Brush roller or drive tracks may be stuck, check for debris and clean if necessary. Cleaner performs by both timing and a pool wall detection sensor, whichever comes first. There are 3 intake ports located at bottom of filter bucket and near the brush roller, check for debris and clean if necessary. Cleaner may get stuck if a high main drain is installed in the pool. Cleaner may remain lodged on the drain for a short period of time, but will eventually free it's self by virtue of the cleaner's embedded program. Cleaner performance: Confusion may exist over the perception of how the cleaner operates at different times during each cycle. It is important to judge the performance of the cleaner by observing improved pool cleanliness after the cleaner has run a complete cleaning cycle. If a cleaner has poor coverage of the pool in one cycle or only covers a small area, check the filter and clean if necessary and make sure the unit is not getting caught on drains, in-floor cleaning heads or toys. The user may try starting the cleaner in different locations to find the optimum cleaning location. If debris falls from cleaner while removing from pool, it may be caused by filter overload, increase frequency of filter cleaning. Assure that there is no large debris blocking any of the three intakes. Large debris must be removed from the pool before using machine. If drain flaps are out of place or stuck by sand or leaves in the open position, the flaps can be snapped back into place, after cleaning the area. If the flotation cord gets twisted which can be caused by the cleaner getting stuck on large objects such as rocks, toys or main drains, it can be straightened by laying the flotation cord at full length (if possible) in the sun; heat from the sun will help reduce the twisting. If a high level of debris is visible through the dome windows, remove cleaner quickly from the water to reduce the chance of the debris escaping the filter bucket and reentering the pool. If you observe the cleaner spending more than the preferred amount of time on the walls/tile line, return the float position to position I (center/default position). USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 17 Weight (w/o cable) Cable Length, Type Materials 23 lb (10.45 Kg) 60 ft (18.29 m) High Impact ABS - Metal Parts of Non-Ferrous Stainless Steel Motor Unit Speed (rpm) Voltage Current (amp) Pump 2700 24 VDC 2.62 A Waterproof Sealing Motor Housing Overload Protection Triple Redundant Radial Shaft Seals & O-ring Sealed, Watertight, High Impact Polypropylene Electronic Overload Monitoring with auto-shutoff Filter Type Media Removable, Re-Usable, Pleated Element Cartridge Pleated Cellulose/Polyester Blend Cleaning Routine Control Type Cleaning Cycle Drive 55 22 VDC 0.63 A PCB 5 VDC - Adaptive Seek Control Logic (ASCL®) Microprocessor Full Cycle 3 hours Drive System Direct Drive w/Polyurethane Drive Track & Acetal/Stainless Steel Bearing System Power Supply Input Primary Voltage Output Secondary Voltage Rated Output Current Weight Shipping Carton Dimensions (mm) Shipping Weight with Caddy without Caddy 110-120 VAC 24 VDC 4A 8.3 lbs (3.8 Kg) Length 24 in (620 mm) 49 lb (22.3 Kg) 43 lb (19.5 Kg) Width 17 in (440 mm) USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Height 30 in (752 mm) 18 IMPORTANT SAFETY INSTRUCTIONS This robotic swimming pool cleaner has been manufactured with the highest degree of care and concern for safety. We suggest the following safety precautions become part of your pool safety regulations: SAVE THESE INSTRUCTIONS 1. ALWAYS PUT THE MACHINE INTO THE WATER BEFORE connecting it to the GFCI protected electrical outlet. 2. IT IS IMPORTANT FOR SWIMMERS’ SAFETY TO REMOVE THE UNIT IMMEDIATELY FOLLOWING USE. THIS CAN ALSO IMPROVE THE OPERATING LIFE OF YOUR CLEANER. 3. BE CERTAIN THE machine IS ONLY PLUGGED into a grounded electrical outlet equipped with an approved and properly operating ground fault circuit interrupter (GFCI). 4. DO NOT HANDLE MACHINE WHILE IT IS PLUGGED INTO THE ELECTRICAL OUTLET. 5. DO NOT USE AN EXTENSION CORD. THIS COULD CREATE A SAFETY HAZARD AND/OR DAMAGE YOUR CLEANER. 6. ALWAYS STAY OUT OF THE POOL WHILE CLEANER IS IN OPERATION. 7. NEVER ALLOW PLUG TO ENTER THE POOL. 8. DO NOT OPERATE THE MACHINE OUT OF WATER. THIS WILL DAMAGE THE MOTOR SEAL AND VOID THE WARRANTY. 9. DO NOT DRAG THE MACHINE OUT OF THE POOL AGAINST THE SIDE WALL. THIS COULD DAMAGE UNIT AND/OR YOUR POOL WALL. 10. DO NOT BURY CORD. DO NOT OPERATE CLEANER WITH DAMAGED CORD. REPLACE DAMAGED CORDS IMMEDIATELY. WARNING - TO REDUCE THE RISK OF INJURY; DO NOT PERMIT CHILDREN TO USE THIS PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES. 11. If the supply cord is damaged it must be replaced by the manufacturer, service agent, or similarly qualified persons in order to avoid a hazard. While the cleaner has been made to operate as safely as possible, we suggest you exercise reasonable care in the handling of the vacuum and inspect the electrical cord frequently for damage or wear, as with any other electrical appliance. After use, remove the unit and rinse with fresh water and remove any twists that may be present in the cord. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 19 HAYWARD® LIMITED WARRANTY All HAYWARD products are covered for manufacturing defects or material defects for a warranty period of 2 years as of date of purchases. Any warranty claim should be accompanied by evidence of purchase, indicating date of purchase. We would therefore advise you to keep your invoice. The HAYWARD warranty is limited to repair or replacement, as chosen by HAYWARD, of the faulty products, provided that they have been subjected to normal use, in compliance with the guidelines given in their user guides, provided that the products have not been altered in any way, and provided that they have been used exclusively with HAYWARD parts and components. The warranty does not cover damage due to frost and to chemicals. Any other costs (transport, labor, etc.) are excluded from the warranty. HAYWARD may not be held liable for any direct or indirect damage resulting from incorrect installation, incorrect connection, or incorrect operation of a product. In order to claim on a warranty and in order to request repair or replacement of an article, please ask your dealer. No equipment returned to our factory will be accepted without our prior written approval. Wearing parts are not covered by the warranty. EXCEPTIONS AND EXCLUSIONS FROM WARRANTY The cleaner must be used with electrical requirements as indicated on the Power Supply. Otherwise damage, defects, malfunctions or other failures of the cleaner arising from use on electrical supply not as indicated are excepted and excluded from this warranty. Defects, malfunctions, failure or damage of the cleaner caused by improper, unreasonable, or negligent use or abuse by the consumer, are excluded from this warranty. If any repair is made on your cleaner by anyone other than authorized personnel (designated to perform such work) without first having obtained factory instructions, HAYWARD, at its sole option, may determine that this warranty will not apply and that reimbursement for such repair will not be made because of failure to comply with such factory specified instructions. Filter cartridges are not covered by this warranty and will be replaced only with your prior approval of the charges. ELECTRIC STANDARD/COUNTRY F NF EN C 15-100 GB BS7671:1992 D DIN VDE 0100-702 EW EVHS-HD 384-7-702 A ÖVE 8001-4-702 H MSZ 2364-702:1994 / MSZ 10-533 1/1990 E UNE 20460-7-702 1993, REBT ITC-BT-31 2002 M MSA HD 384-7-702.S2 Wiring Rules + IS HD 384-7-702 PL PN-IEC 60364-7-702:1999 CEI 64-8/7 CZ CSN 33 2000 7-702 LUX 384-7.702 S2 SK STN 33 2000-7-702 NL NEN 1010-7-702 SLO SIST HD 384-7-702.S2 P RSIUEE TR TS IEC 60364-7-702 IRL I USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 20 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 21 PRODUCT REGISTRATION (Retain For Your Records) DATE OF INSTALLATION ____________________ ▲Retain this Warranty Certificate (upper portion) in a safe and convenient location for your records. DETACH HERE: Fill out bottom portion completely and mail within 10 days of purchase/installation or register online. ------------------------------------------------------------------------------------------------------------------------ AUTOMATIC SURFACE SKIMMER Warranty Card Registration Register online at www.hayward.com Please Print Clearly: Years Pool has been in service First Name____________________ Last Name____________________ < 1 year 1-3 4-5 6-10 11-15 >15 Street Address______________________________________________ Purchased from_____________________________ City_____________________________ State___________ Zip_______ Builder Retailer Pool Service Internet/Catalog Phone Number_____________________ Purchase Date_____________ Company Name________________________________ E-Mail Address______________________________________________ Address______________________________________ Serial Number City____________________ State_____ Zip________ Phone________________________________________ _ Model Number____________________________________________________ Type of Pool: Pool Capacity_______________(U.S. Gallons) Please include me on all e-mail communications regarding Hayward Equipment or promotions. Mail to: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Attn: Warranty Dept Or REGISTER YOUR WARRANTY ON-LINE AT WWW.HAYWARD.COM Concrete/Gunite Vinyl Fiberglass Other_____________________________ New Installation Replacement Installation for: In Ground Above Ground Spa Hayward is a registered trademark of Hayward Industries, Inc. © 2011 Hayward Industries, Inc. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 22 ISRC9740XLN Rev -3 SharkVAC XL™ / e.VAC PRO™ par Hayward Pool Products 620 Division Street, Elizabeth, NJ 07207 Téléphone: (908) 351-5400 www.hayward.com UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 23 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 24 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 25 Hayward Pool Products 620 Division Street Elizabeth, NJ 07207 DANGER AVERTISSEMENT ATTENTION UTILISATION DU NETTOYEUR AUTOMATIQUE AVERTISSEMENT ATTENTION AVERTISSEMENT UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 26 AVERTISSEMENT – LISEZ CES CONSEILS D’UTILISATION IMPORTANTS AVANT D’UTILISER VOTRE APPAREIL! UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 27 11,5 pi (3,5 m) UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 28 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 29 1. Bloc d’alimentation 2. Interrupteur Marche/Arrêt 3. Câble flottant 5. Cartouche de filtre 6. Panier de filtre 14. Entraînement 15. UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 30 INSTRUCTIONS POUR LE CHARIOT – VOIR SCHÉMA UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 31 Fig. 6 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 32 Fig. 7 Fig. 8 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 33 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 34 LIGNE D’EAU Escalade des parois FONCTION D’ESCALADE DES PAROIS 35 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 36 CONSEILS IMPORTANTS UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 37 DÉPANNAGE UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 38 Pompe 2700 24 V c.c. 2,62 A Filtre Type Substrat Entraînement 55 22 V c.c. 0,63 A PCB 5 V c.c. - Longueur 620 mm (24 po) 22,3 kg (49 lb) 19,5 kg (43 lb) UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 39 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 40 NORME ÉLECTRIQUE/PAYS F NF EN C 15-100 GB BS7671:1992 D DIN VDE 0100-702 EW EVHS-HD 384-7-702 A ÖVE 8001-4-702 H MSZ 2364-702:1994 / MSZ 10-533 1/1990 E UNE 20460-7-702 1993, REBT ITC-BT-31 2002 M MSA HD 384-7-702.S2 PL PN-IEC 60364-7-702:1999 CEI 64-8/7 CZ CSN 33 2000 7-702 LUX 384-7.702 S2 SK STN 33 2000-7-702 NL NEN 1010-7-702 SLO SIST HD 384-7-702.S2 P RSIUEE TR TS IEC 60364-7-702 IRL I UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 41 1 RCX97471SB RCX97471CY 10 11 RCX97415 RCX97445 20 21 RCX59004 RCX12302 30 31 RCX97435 RCX97439 40 41 RCX 97441 RCX97410BK 2 RCX97472 12 RCX97407 22 RCX97462 32 RCX97437 42 RCX26008 3 RCX97431 13 RCX97455 23 RCX12301 33 RCX97430 43 RCX97461 4 RCX97433 14 RCX12010 24 RCX59002 34 RCX23002G 5 RCX97423 15 RCX11000 25 RCX97429 35 RCX97440 6 RCX97477 16 RCX97490XLN 26 RCX97459 36 RCX97403 45 RCX97427 7 RCX70101 17 RCX40117 27 RCX97401GR 37 RCX97449 46 RCX97453 8 RCX97417 18 RCX50064 28 RCX26000 38 RCX12011 9 RCX97405 19 RCX59006 29 RCX97443 39 RCX97520BK 44 UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD RCX97480SB RCX97480CY 42 ENREGISTREMENT DU PRODUIT (À conserver dans vos dossiers) ------------------------------------------------------------------------------------------------------------------------------ ÉCUMOIRE AUTOMATIQUE DE SURFACE Enregistrement de la carte de garantie Adresse______________________________________ Type de piscine: Postez à: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Attn: Warranty Dept ou ENREGISTREZ VOTRE GARANTIE EN LIGNE À WWW.HAYWARD.COM Hors terre Spa UTILISEZ UNIQUEMENT DES PIÈCES ORIGINALES DE RECHANGE HAYWARD 43 ISRC9740XLN Rev -2 ™ SharkVAC XL / e.VAC PRO ™ de ADVERTENCIA – Para reducir los peligros de atrapamiento: o o o o o o o o USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 45 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 46 Hayward Pool Products 620 Division Street Elizabeth, NJ 07207 PELIGRO ADVERTENCIA PRECAUCIÓN OPERACIÓN DEL LIMPIADOR ADVERTENCIA PRECAUCIÓN ADVERTENCIA USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 47 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 48 11.5 pies (3,5 m) 49 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 50 1. Suministro eléctrico 8. Conjunto de domo 9. Panel lateral 10. Rueda 4. Mango 7. Puerta del filtro 14. Pista USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 51 INSTRUCCIONES SOBRE EL CARRITO – VEA EL DIAGRAMA USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 52 Fig. 6 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 53 Fig. 7 Fig. 8 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 54 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 55 LÍNEA DE AGUA II. Limpieza activa del piso FUNCIÓN DE ASCENSO POR LA PARED USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 56 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 57 CONSEJOS IMPORTANTES USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 58 SOLUCIÓN DE PROBLEMAS USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 59 Bomba 2700 24 VCC 2.62 A PCB 5 VCC - 110 a 120 VCA 24 VCC 4A 8.3 lb (3.8 kg) Largo Ancho Altura 17 pulg. (440 mm) 30 pulg. (752 mm) USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 60 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 61 NORMA ELÉCTRICA/PAÍS F D A E IRL I LUX NL P GB EW H M BS7671:1992 EVHS-HD 384-7-702 MSZ 2364-702:1994 / MSZ 10-533 1/1990 MSA HD 384-7-702.S2 PL CZ SK SLO TR PN-IEC 60364-7-702:1999 CSN 33 2000 7-702 STN 33 2000-7-702 SIST HD 384-7-702.S2 TS IEC 60364-7-702 USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 62 1 RCX97471SB RCX97471CY 10 11 RCX97415 RCX97445 20 21 RCX59004 RCX12302 30 31 RCX97435 RCX97439 40 41 RCX 97441 RCX97410BK 2 RCX97472 12 RCX97407 22 RCX97462 32 RCX97437 42 RCX26008 3 RCX97431 13 RCX97455 23 RCX12301 33 RCX97430 43 RCX97461 4 5 RCX97433 RCX97423 14 15 RCX12010 RCX11000 24 25 RCX59002 RCX97429 34 35 RCX23002G RCX97440 44 RCX97480SB RCX97480CY 6 RCX97477 16 RCX97490XLN 26 RCX97459 36 RCX97403 45 RCX97427 7 RCX70101 17 RCX40117 27 RCX97401GR 37 RCX97449 46 RCX97453 8 RCX97417 18 RCX50064 28 RCX26000 38 RCX12011 9 RCX97405 19 RCX59006 29 RCX97443 39 RCX97520BK USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 63 REGISTRO DEL PRODUCTO (Consérvelo para sus archivos) ------------------------------------------------------------------------------------------------------------------------ DESNATADOR AUTOMÁTICO DE SUPERFICIE Registro tarjeta garantía Internet/catálogo Escriba a: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Attn: Warranty Dept O REGISTRE SU GARANTÍA EN LÍNEA EN WWW.HAYWARD.COM Teléfono_________________________________________ Tipo de piscina: Reemplazo USE SOLAMENTE REPUESTOS GENUINOS DE HAYWARD 64 ISRC9740XLN Rev -2 65
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement