INSTRUCTION MANUAL MANUEL D`INSTRUCTION

GB
FAT BEAM LASER SHOW SYSTEM
SYSTEME LASER « LASTUBE »
SISTEM LASER « LASTUBE »
LASERY TUBOWE
LASTUBE80G/LASTUBE200R/LASTUBE300B
INSTRUCTION MANUAL
MANUEL D’INSTRUCTION
MANUAL DE UTILIZARE
INSTRUKCJA OBSŁUGI
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
Thanks for your purchasing, please read this manual carefully before
operating the system. It gives you general information for your safe and
better operation.
Safety Recommendations
 Before any installation and repair, please do cut off the power supply.
 For safety reasons, install the unit firmly to avoid injury and damage.
 Do not cover the unit.
 The product should be installed by professional technician.
 Do not touch the unit with wet hands or pull the power wire forcefully.
 The system should be kept dry .Please don’t use the system in the
condition of rain, wet or dust. For indoor use only.
 Do not turn on or off the system frequently, and avoid keeping it
working for a long time.
 Fixed Installation prevents the system from strong shaking or striking.
 Prevent objects to get into the system, or there will be malfunction.
 Leave at least 1m distance between the unit and other objects.
 Please don’t connect the power supply or turn on the system before
installation.
 Before switching on power, please make sure the power wire is in good
condition.
 Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily operable.
 When transport the system again, please use the original package to
avoid shaking.
Statement
The user should comply with the instructions and warnings above. Any
damage, which is caused by incorrect operation or not following the
manual, is not covered by the warranty.
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 1
Installation guide
 Be sure that there are no inflammable or explosive objects within 1.5m
distance.
 Before installation, please make sure the power voltage matches the
system rated voltage.

Be sure that the fan and exhaust is not blocked.
INSPECTION
Check for the contents in the package refer to the following list:
1. Laser lighting: 1
2. Power cable: 1
3. User’s manual: 1
Function Setting
0=OFF 1=ON
DIPSWITCH CHART
#1 #2 #3 #4 #5 #6 #7 #8 #9
0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 1
0 0 0 0 0 0 0 0 0
FUNCTION
#10
1
SOUND ACTIVE
1
AUTO MODE
0
DMX (slave mode)
Master-Slave Operation
This mode will allow you to link the units together without controller.
1. Install the units in a suitable position (laying or appending).
2. Choose a unit to function as Master mode, set dipswitch to select Sound
Active or AUTO mode. The others must be set to Slave mode, set dipswitch
to select Slave mode.
3. Use standard XLR microphone cable chain your units together via the
XLR connector on the rear of the units. For longer cable runs we suggest a
terminator at the last fixture.
4. Turn on all units' power, the units begins reset, and then the unit begins
working. The slave units will react like the master unit.
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
There are five modes in the slave units:
#
1
0
1
0
1
1
#
2
0
0
1
1
1
#
3
0
0
0
0
1
#
4
0
0
0
0
0
#
5
0
0
0
0
0
#
6
0
0
0
0
0
#
7
0
0
0
0
0
#
8
0
0
0
0
0
#
9
0
0
0
0
0
#10
Slave effect
0
0
0
0
0
Flow master
Same as master
Y-axis contrary
X-axis contrary
Both X-axis and
Y-axis contrary
Installation
1、Firstly, be sure that the using voltage is match with the voltage marked
on the base of the laser lighting;
2、Installation should be made by professional technician. Fix the laser
lighting and adjust the angle of the laser lighting to you need;
3、Please check whether the fan and the exhaust are blocked;
4、There is a hole for connection. When hang the laser lighting, be sure
the cable can undertake 10 times of the lighting weight;
5、The laser lighting should be fixed;
6、It is essential to be earthed well for the sake of safety.
DMX512
This laser light is controlled by the standard DMX. Please connect
controlling panel with the lighting as following
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 2
DMX Control Parameter Chart
Channel No
Channel 1
DMX512 fig.
Control mode
Content
0--49
Laser off
50--99
100--149
150--199
200--255
Sound active
Manual mode 1
Channel 2
X axis
0~255
Manual move
Channel 3
Y axis
0-255
Manual move
0
No strobe
1-255
strobe
Channel 4
No special
Channel 5
strobe
Manual Mode 2
Channel 2
Pattern selection
0~255
Channel 3
Motor speed
0-255
Channel 4
Patterns moving
0-255
Patterns different
From fast to slow
☆ Please clean the lighting surface and engine outlet regularly.
☆ Be sure that there is no flammable or explosive subject nearby. The
least distance is 0.5 meters. at the same time, keep more than 15cm
between the wall and laser lighting;
Warning
 Power off before installation or maintenance;
 The danger class of this laser lighting is CLASS Ⅲ B. It’s dangerous for
observing laser.
 Keep at least 0.5 meters distance between the lighting and
flammable material;
Technical parameters
Effect: ................................... fat beam laser net with 18mm pointer
Motor: .............................................. N1.8 high precision step motor
Control mode： .......................................... sound control/auto/dmx
Dimensions： ........................................... 215mm x 70mm x 147mm
Power supply： .............................................. AC100-240V, 50/60Hz
Net weight： ........................................................................... 1.5KG
Gross weight： ......................................................................... 2.0KG
Laser diode: .......................................................................... DPSS
LASTUBE80G ................................................................. Green 532nm
LASTUBE200R....................................................................Red 650nm
LASTUBE300B................................................................... Blue 450nm
Laser power：
LASTUBE80G ............................................................................ 80mW
LASTUBE200R: ....................................................................... 200mW
LATUBE300B: ......................................................................... 300mW
☆ Please clean the lens regularly. Do not do it using the wet cloth or
other chemical. the clean times is depend on the using frequency and
surrounding condition; it is recommended that should be cleaned every
20 days;
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 3
DANGER
LASER RADIATION
AVOIR EYE EXPOSURE TO BEAM
LASER PRODUCT CLASS 3B





Electric products must not be put into household waste. Please bring them to a
recycling centre. Ask your local authorities or your dealer about the way to
proceed.




This LASER effect is built for professional use. It must
be installed by a professional in a sufficient height
above the floor so that it can never hit the eye of the audience.
Never create a fixed point.



©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B


Page 4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
AUTOMATIQUE
DMX (Mode esclave)
#2
#3
#4
#5
#6
#7
#8
#9
#10
0
1
0
1
1
0
0
1
1
1
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
DMX512
fig.
N° du canal
Mode de
contrôle
0--49
50--99
mode Manuel 1
100--149
mode Manuel 2
150--199
Mode Auto
200--255
Activation audio
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 5
Canal 2
Axe-X
0~255
Canal 3
Y axis
0-255
0
Pas d’effet strobo
1-255
Stroboscope
Canal 5
Mode Manuel 2
Canal 2
0~255
Canal 3
0-255
Canal 4
0-255
Rapide vers lent
LASTUBE80G / LASTUBE200R / LASTUBE300B
DANGER
RADIATION LASER
NE PAS EXPOSER VOS YEUX AU RAYON
PRODUIT LASER DE CLASSE 3B
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 6
1
LASTUBE80G / LASTUBE200R / LASTUBE300B
#
#
#
#
#
#
#
#
#
2 3 4 5 6 7 8 9 10
0 0 0 0 0 0 0 0 0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 7
Eixo Y
Canal 4
No special
Canal 5
strobe
0~255
Movimento manual
0-255
Movimento manual
0
1-255
Sem strobe
strobe
0-255 De rápido para lento
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 8
#2
#3
#4
#5
#6
#7
#8
#9
#10
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
1. Laser: 1
2. Cablu de alimentare: 1
3. Ghid de utilizare: 1
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
#
1
#
2
#
3
#
4
#
5
#
6
#
7
#
8
#
9
#10
0
0
0
0
0
0
0
0
0
0
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 9
1
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
DMX512 fig.
Axa-Y inversa
1
1
0
0
0
0
0
0
0
0
Axa-X inversa
1
1
1
0
0
0
0
0
0
0
Atat axa- X cat si
axa Ysunt
inverse
Mod
Canal 1
DMX512
0--49
Laser oprit
50--99
Mod Manual 1
100--149
Mod Manual 2
150--199
Mod Auto
200--255
Mod Manual 1
Canal 2
Axa X
0~255
Mutare manuala
Canal 3
Axa Y
0-255
Mutare manuala
Canal 4
Fara efecte speciale
0
Fara stroboscop
1-255
Stroboscop
Canal 5
Stroboscop
Mod Manual 2
©Copyright Lotronic
Descriere
LASTUBE80G / LASTUBE200R / LASTUBE300B
Canal 2
Selectare model
0~255
Canal 3
Viteza motor
0-255
Canal 4
Deplasare modele
0-255
Modele diferite
De la viteza mare la viteza
mica
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 10
LASTUBE200R:........................................................................ 200mW
LATUBE300B: .......................................................................... 300mW
LASTUBE80G / LASTUBE200R / LASTUBE300B
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 11
#
2
0
0
1
1
1
#
3
0
0
0
0
1
#
4
0
0
0
0
0
#
5
0
0
0
0
0
#
6
0
0
0
0
0
#
7
0
0
0
0
0
#
8
0
0
0
0
0
#
9
0
0
0
0
0
#10
0
0
0
0
0
FUNKCJA
TRYB MUZYCZNY
TRYB AUTO
DMX (slave)
LASTUBE80G / LASTUBE200R / LASTUBE300B
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 12
Tryb manualny 1
Kanał 2
Oś X
0~255
Ruch manualny
Kanał 3
Oś Y
0-255
Ruch manualny
0
Brak stroboskopu
1-255
Stroboskop
Nd.
Tryb manualny 2
Kanał 2
0~255
Kanał 3
0-255
Kanał 4
0-255
Kanał 1
Wartośd dla
DMX512
0--49
50--99
Tryb manualny 1
100--149
Tryb manualny 2
150--199
Tryb Auto
200--255
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 13
©Copyright Lotronic
LASTUBE80G / LASTUBE200R / LASTUBE300B
LASTUBE80G / LASTUBE200R / LASTUBE300B
Page 14