ED655 Airless Pump

ED655 Airless Pump
ED655
Airless Pump
SPRAY
PRIME
PRIME
Owner’s Manual • Notice d’utilisation • Manual del Propietario
Model Number 0508028
SprayTECH
1770 Fernbrook Lane
Minneapolis, MN 55447
Printed in the U. S. A.
0999 © 1999 SprayTECH Corporation. All rights reserved. Form No. 0279573B
Español Français English
Table of Contents
General Description
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Attaching the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Attaching the Paint Hose . . . . . . . . . . . . . . . . . . . . . . . . 5
Attaching the Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . . . . . . 6
Priming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Preparing to Prime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting the Paint Hopper. . . . . . . . . . . . . . . . . . . . . . . 7
Attaching the Return Tube . . . . . . . . . . . . . . . . . . . . . . . 7
Priming the Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Spraying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Spraying Technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Practice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Overnight Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
Removing and Cleaning theInlet Valves . . . . . . . . . . . . 11
Removing and Cleaning the Outlet Valve . . . . . . . . . . . 11
Cleaning the Spray Tip . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning the Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Replacing the Valve Spring Unit . . . . . . . . . . . . . . . . . . 12
Choosing the Correct Spray Gun Filter . . . . . . . . . . . . . 12
Cleaning the Hopper Screen . . . . . . . . . . . . . . . . . . . . 12
Tightening the PRIME/SPRAY knob . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Parts Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-41
Final Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Hopper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Paint Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 40
G-10 Spray Gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Français. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
This high performance airless sprayer is a precision power tool
used for spraying many types of materials. Read and follow
this instruction manual carefully for proper operating
instructions, maintenance and safety information.
Specifications
Weight ..............................27 lbs.
Capacity ...........................Up to .35 gallon (1.25 liters) per
minute.
Power source ...................Electric motor, totally enclosed, fan
cooled.
Power requirement ...........15 amp minimum circuit on 115
VAC, 60 Hz current.
Generator .........................15 amp A/C.
Spraying pressure ............Up to 2600 psi.
Safety features .................Spray gun trigger lock and pressure
diffuser; built-in tip safety guard;
priming knob for safe pressure
release.
Portability..........................Compact design, light weight for
easy movement.
Capability..........................Sprays a variety of paints, oil base
latex, primers, stains, preservatives
and other nonabrasive materials,
including pesticides and liquid
fertilizers.
Components
PRIME
2
SPRAY
English
PRIME
The shipping carton for your painting system contains the
following:
• Stand, motor, and pump attached
• Handle and two handle pins
• Paint hopper and return tube
• Spray gun and filter
• Spray tip and gasket
• Pressure hose
The following are located in the literature set with this owner’s
manual:
• Registration card
© SprayTECH Corporation. All rights reserved.
• ALWAYS lock the gun trigger, shut the fluid pump off and
release all pressure before servicing, cleaning the tip
guard, changing tips, or leaving unattended. Pressure will
not be released by turning off the engine. The
PRIME/SPRAY knob must be turned to PRIME to relieve
the pressure. Refer to the PRESSURE RELIEF
PROCEDURE described in this manual.
• ALWAYS have the tip guard in place while spraying. The
tip guard provides some protection against injection
injuries but is mainly a warning device.
• ALWAYS remove the spray tip before flushing or cleaning
the system.
• Inspect the paint hose before each use. The paint hose
can develop leaks from wear, kinking and abuse. A leak is
capable of injecting material into the skin.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• All accessories must be rated at or above 2800 PSI. This
includes spray tips, guns, extensions, and hose.
Safety Precautions
This manual contains information which must be read and
understood before using the equipment. When you come to an
area which has one of the following symbols, pay particular
attention and make certain to heed the safeguard.
WARNING
This symbol indicates a potential hazard which may cause
serious injury or loss of life. Important safety information will
follow.
CAUTION
This symbol indicates a potential hazard to you or to the
equipment. Important information that tells how to prevent
damage to the equipment or how to avoid causes of minor
injuries will follow.
NOTE TO PHYSICIAN:
Injection into the skin is a traumatic injury. It is important
to treat the injury surgically as soon as possible. DO NOT
delay treatment to research toxicity. Toxicity is a concern
with some coatings injected directly into the blood
stream. Consultation with a plastic surgeon or
reconstructive hand surgeon may be advisable.
NOTE: Notes give important information which
should be given special attention.
CAUTION
This unit is provided witha a thermally protected
automatic reset. If an overload occurs the thermally
protected automatic reset disconnects the motor from the
power supply.
• The motor will restart without warning when the protector
automatically resets.
• Always disconnect the motor from the power supply
before working on the equipment.
• When the thermally protected automatic reset disconnects
the motor from the power supply, relieve pressure by
turning the priming valve to PRIME.
• Turn the ON/OFF switch to OFF.
HAZARD: EXPLOSION OR FIRE - Solvent and paint fumes
can explode or ignite, causing property damage
and/or severe injury.
PREVENTION:
• Exhaust and fresh air introduction must be provided to keep
the air within the spray area free from accumulation of
flammable vapors.
• Avoid all ignition sources such as static electricity sparks,
open flames, pilot lights, hot objects, cigarettes, and sparks
from connecting and disconnecting power cords or working
light switches.
• Fire extinguishing equipment must be present and in good
working order.
• Keep the pump away from the spray area to avoid solvent
and paint fumes.
• High velocity flow of material through equipment may
develop static electricity. The equipment being used, as well
as objects in and around the spray area must be properly
grounded to prevent static discharge and sparks.
• Use only conductive or grounded high pressure fluid hoses
for airless applications. Be sure that the gun is grounded
properly through hose connections.
• Follow the material and solvent manufacturer's safety
precautions and warnings.
• When flushing equipment use the lowest possible pressure.
NOTE: The cause of the overload should be corrected
before restarting. See TROUBLESHOOTING.
WARNING
HAZARD: Injection injury - A high pressure stream of
paint produced by this equipment can pierce
the skin and underlying tissues, leading to
serious injury and possible amputation.
DO NOT TREAT AN INJECTION INJURY AS A SIMPLE CUT!
Injection can lead to amputation. See a physician
immediately.
The maximum operating range of the gun is 2800 PSI fluid
pressure.
HAZARD: EXPLOSION HAZARD DUE TO INCOMPATIBLE
MATERIALS - May cause property damage or
severe injury.
PREVENTION:
• NEVER aim the gun at any part of the body.
• NEVER allow any part of the body to come in contact
with the fluid stream. DO NOT come in contact with a fluid
stream created by a leak in the fluid hose.
• NEVER put your hand in front of the gun. Gloves will not
provide protection against an injection injury.
© SprayTECH Corporation. All rights reserved..
PREVENTION:
• Do not use bleach.
• Do not use Halogenated hydrocarbon solvents such as
methylene chloride and 1,1,1 - trichloroethane. They are
not compatible with aluminum and may cause an
explosion. If you are unsure of a material’s compatibility
with aluminum, contact your coating's supplier.
3
English
Grounding Instructions
WARNING
This product must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product
is equipped with a cord having a grounding wire with an
appropriate grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
HAZARD: HAZARDOUS VAPORS - Paints, solvents,
insecticides, and other materials may be
harmful if inhaled, causing severe nausea,
fainting, or poisoning.
PREVENTION:
• Use a respirator or mask whenever there is a chance that
vapors may be inhaled. Read all instructions with the
mask to ensure that it will provide the necessary
protection against the inhalation of harmful vapors.
WARNING
Improper installation of the grounding plug can result in a
risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not
connect the green grounding wire to either flat blade terminal.
The wire with insulation having a green outer surface with or
without yellow stripes is the grounding wire and must be
connected to the grounding pin.
Check with a qualified electrician or serviceman if the
grounding instructions are not completely understood, or if you
are in doubt as to whether the product is properly grounded.
Do not modify the plug provided. If the plug will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
This product is for use on a nominal 120 volt circuit and has a
grounding plug that looks like the plug illustrated below. A
temporary adapter which looks like the adapter illustrated in
the figure below may be used to connect this plug to a 2 pole
receptacle as shown if a properly grounded outlet is not
available.
The temporary adapter should be used only until a properly
grounded outlet as shown below can be installed by a qualified
electrician. The green colored rigid ear lug or the grounding
wire extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place
by a metal screw.
HAZARD: GENERAL - May cause property damage or
severe injury.
PREVENTION:
• Read all instructions and safety precautions before
operating any equipment.
• Comply with all appropriate local, state, and national
codes governing ventilation, fire prevention, and
operation.
• The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.
• This high pressure airless pump is designed to be used
with manufacturer authorized parts only. When using this
pump with parts that do not comply with the minimum
specifications and safety devices of the pump
manufacturer, the user assumes all risks and liabilities.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover, as well as damage or movement of
couplings. If any of these conditions exist, replace the
hose immediately. Never repair a paint hose. Replace it
with another grounded hose.
• All hoses, swivels, guns, and accessories used with this
unit must be pressure rated at or above 2800 PSI.
• Do not spray on windy days.
Grounded Outlet
CAUTION
Grounding Pin
Use only a 3-wire extension cord that has a 3-blade grounding
plug and a 3-slot receptacle that will accept the plug on the
product. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting in loss
of power and overheating. A 14 or 12 gauge cord is
recommended.
Cover for grounded outlet box
Metal Screw
Adapter
Tab for
Grounding Screw
NOTE: Do not use more than 100 feet of extension
cord. If you need to paint further than 100
feet from your power source, use more paint
hose, not more extension cord. Shorter
extension cords will ensure maximum
electrical power for proper operation.
English
4
© SprayTECH Corporation. All rights reserved.
Attaching the Tip
Setup
Assembling the Tip
Attaching the Handle
If the spray tip is disassembled:
1. Insert the tip into the spray guard and turn the tip to the
spray position so that the arrow is facing toward the front
of the spray gun.
NOTE: The sprayer should remain unplugged during
assembly.
1. Slide the handle into the stand until the holes on the
handle line up with the holes in the stand.
2. Slide the handle pins through the holes in the stand and
the handle to secure the handle in position.
Spray Guard
SPRAY
Tip
Attaching the Tip to the Gun
1. Lock the gun by turning the gun trigger lock so that it is
parallel to the gun body.
Attaching the Paint Hose
1. Attach the high pressure hose to the paint hose port. Use
a wrench to tighten the paint hose securely.
Gun locked OFF
(gun will not spray)
POSSIBLE INJECTION HAZARD. Do not spray without the
tip guard in place. Never trigger the gun unless the tip is in
either the spray or the unclog position. Always engage the
gun trigger lock before removing, replacing, or cleaning tip.
2. Thread the spray tip onto the gun. Tighten the nut by
hand first, then tighten more firmly with a wrench.
SPRAY
PRIME
WARNING
NOTE: When attaching the tip to the gun, align the
tip guard as shown in the figure below, then
tighten with a wrench.
High Pressure Hose
2. Attach the gun to the other end of the high pressure hose.
Tighten securely with two wrenches.
Begin
tightening
the tip at
this angle
to achieve
the desired
spray angle
when tight.
3. Plug the sprayer into a properly grounded outlet or heavy
duty grounded extension cord. Do not use more than 100
feet of cord. If you must spray a long distance from a
power source, use more paint hose, not more extension
cords. Use a minimum size of 16 gauge for power
extension cords up to 50 feet in length, or 12 to 14 gauge
for power extension cords between 50 and 100 feet in
length.
© SprayTECH Corporation. All rights reserved.
5
English
Pressure Relief Procedure
Priming
Follow this procedure after the unit is assembled and before
any operation which involves the spray gun such as cleaning
and maintenance or changing tips or accessories.
1. Turn the pressure control knob counterclockwise to its
lowest setting.
Preparing to Prime
1. Fill the inlet valve with water or with a light household oil.
PRIME
PRIME
SPRAY
R
A
Y
PRIME
SP
IM
PR
SPRAY
2. Make certain that the PRIME/SPRAY knob is set to
PRIME and that the pressure control knob is turned
counterclockwise to the lowest pressure setting.
3. Turn the motor switch to ON.
4. Increase the pressure by turning the pressure control
knob clockwise 1/2 turn.
5. Force the inlet valve to open and close by pushing on it
with a screwdriver or the eraser end of a pencil. It should
move up and down about 1/16 of an inch. Continue until
water or oil is sucked into the sprayer. This will wet the
moving parts and break loose any old paint residue.
PRIME/SPRAY Knob
2. Turn the PRIME/SPRAY knob to PRIME.
3. Trigger the gun to remove any pressure which may still be
in the hose.
4. Lock the gun by turning the gun trigger lock so that it is
parallel to the gun body.
Gun locked OFF
(gun will not spray)
IM
WARNING
R
A
Y
PR
SP
E
6. Put the palm of your hand over the inlet. Turn the
pressure control knob clockwise to its maximum setting.
You should feel suction coming from the inlet valve. If you
do not, see the section on cleaning and servicing the outlet
valve.
SP
R
A
Y
PR
Injection hazard. Do not spray without the tip guard in place.
NEVER trigger the gun unless the tip is completely turned to
either the spray or the unclog position. ALWAYS engage the gun
trigger lock before removing, replacing or cleaning tip.
IM
E
7. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
8. Turn the motor switch to OFF.
English
6
© SprayTECH Corporation. All rights reserved.
Mounting the Paint Hopper
Priming the Pump
1. Align the bottom of the paint hopper with the threaded
inlet valve on the paint pump block.
2. Turn the paint hopper clockwise to thread it onto the inlet
valve. Continue to turn the paint hopper until it is secure
on the inlet valve.
1. Turn the pressure control knob counterclockwise to its
lowest pressure setting.
PRIME
PRIME
NOTE: Make sure the threads are straight and the
hopper turns freely on the inlet valve. Do not
cross-thread.
SPRAY
3. Place the filter screen into the bottom of the paint hopper
and snap it in position.
1. Make sure that the motor switch is turned to OFF.
2. Screw the return tube fitting found in the literature set into the
return tube port on the side of the pump and tighten firmly by
hand.
SPRAY
PRIME
PRIME
Attaching the Return Tube
PRIME/SPRAY Knob
NOTE: Do not over-tighten. Hand-tighten only. Some
threads will be visible even when fully
tightened.
2. Turn the PRIME/SPRAY knob to PRIME.
3. Turn the motor switch to ON.
4. Turn the pressure control knob clockwise to between half
and full pressure. You should see the paint move through
the suction tube to the pump. Let the unit prime 1 to 2
minutes after paint begins to flow through the return tube.
3. Place the straight end of the return tube into the return
tube fitting.
Return Tube Fitting
CAUTION
SPRAY
PRIME
Always reduce the pressure to zero before changing the
position of the priming knob. Failure to do so may cause
damage to the paint pump diaphragm.
CAUTION
If the pressure control knob is reduced to zero and the
PRIME/SPRAY knob is still on SPRAY while the sprayer is
operating, there will be high pressure in the hose and
spray gun until the priming knob is turned to PRIME or
until the spray gun is triggered to relieve the pressure.
Return Tube
4. Thread the nut on the return tube onto the return tube
fitting and tighten until the return tube is secure.
5. Place the hook end of the return tube into the hole in the
paint hopper cover.
Return Tube
SPRAY
PRIME
PRIME
Paint Hopper Cover
© SprayTECH Corporation. All rights reserved.
7
English
Spraying
Proper way to trigger the spray gun
Spraying Technique
Keep stroke
even
The key to a good paint job is an even coating over the entire
surface. This is done by using even strokes. Keep your arm
moving at a constant speed and keep the spray gun at a
constant distance from the surface. The best spraying
distance is 10 to 12 inches between the spray tip and the
surface.
Light Coat
Heavy Coat
Light Coat
Start stroke
Pull trigger
Aproximately
10 to 12 inches
Keep steady
Release trigger
End stroke
Overlap each stroke by about 30%. This will ensure an even coating.
When you stop painting, lock the gun trigger lock, turn the
pressure control knob counterclockwise to its lowest setting
and set the priming knob to PRIME. Turn the motor switch to
OFF and unplug the sprayer.
If you expect to be gone more than 1 hour, follow the short
term clean up procedure described in the CLEANUP section of
this manual.
Practice
Do not flex wrist while spraying.
1. Be sure that the paint hose is free of kinks and clear of
objects with sharp cutting edges.
2. Turn the pressure control knob counterclockwise to its to
its lowest setting.
Keep the spray gun at right angles to the surface. This means
moving your entire arm back and forth rather than just flexing
your wrist.
Even coat throughout
PRIME
Approximately
10 to 12 inches
SPRAY
PRIME
PRIME
SPRAY
Keep stroke smooth and at an even speed.
Keep the spray gun perpendicular to the surface, otherwise
one end of the pattern will be thicker than the other.
PRIME/SPRAY Knob
3. Turn the PRIME/SPRAY knob to SPRAY.
4. Turn the pressure control knob clockwise to its highest
setting. The paint hose should stiffen as paint begins to
flow through it.
5. Unlock the gun trigger lock by turning the switch so that it
is parallel to the handle.
6. Trigger the spray gun to bleed air out of the hose.
7. When paint reaches the spray tip, spray a test area to
check the spray pattern.
8. Use the lowest pressure setting necessary to get a good
spray pattern. If the pressure is set too high, the spray
pattern will be too light. If the pressure is set too low,
tailing will appear or the paint will spatter out in gobs
rather than in a fine spray.
Approximately
10 to 12 inches
Right way
Wrong way
The spray gun should be triggered by turning it on and off with
each stroke. This will save paint and avoid paint buildup at the
end of the stroke. Do not trigger the gun during the middle of a
stroke. This will result in an uneven spray and splotchy
coverage.
Good spray pattern
Paint tailing pattern
English
8
© SprayTECH Corporation. All rights reserved.
Long-Term Storage
Cleanup
Overnight Storage
WARNING
Shutdown
Do not allow paint to build up on the motor or the motor
will overheat. Do not allow flammable solvents to come in
contact with the motor or they could ignite.
1. Lock the gun by turning the gun trigger lock parallel with
the gun body.
2. Turn the pressure control knob counterclockwise to the
minimum setting.
3. Turn the PRIME/SPRAY knob to PRIME.
4. Turn the motor switch to OFF and unplug the sprayer.
5. For latex materials only, pour 1/2 cup water slowly on the
top of the paint to prevent the paint from drying. For other
materials, seal the paint hopper with the hopper cover
keeping the return tube in the paint.
NOTE: You will need a bucket, cleaning solution, a
toothbrush, a wrench and cleaning rags.
NOTE: If spraying with latex paint, use warm soapy
water for cleaning. If using oil or alkyd-based
paints, use mineral spirits or paint thinner.
CAUTION
Do not use mineral spirits or paint thinner on latex paint,
or the mixture will turn into a jelly-like substance which is
difficult to remove.
Clearing the Paint Hopper
1. Lock the gun by turning the gun trigger lock parallel with
the gun body.
2. Turn the pressure control knob counterclockwise to the
minimum setting.
3. Turn the PRIME/SPRAY knob to PRIME.
4. Turn the motor switch to OFF and unplug the sprayer.
5. Direct the return tube into the original paint bucket.
6. Plug the sprayer in and turn the motor switch to ON.
7. Turn the pressure control knob to 1/2 maximum pressure.
This will draw the remaining paint in the paint hopper through
the pump, up the return tube, and into the paint bucket.
8. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
9. Trigger the gun to relieve pressure and lock the gun.
10. Remove the spray tip and guard and place them into a
container of water or appropriate solvent for the type of
material with which you are painting.
11. Fill the paint hopper with water or an appropriate solvent
for the type of material with which you are painting.
12. Increase the pressure to 1/2 the maximum pressure. Let
the water or solvent circulate for 2-3 minutes to flush paint
out of the pump, the paint hopper, and the return tube.
6. Wrap the spray gun assembly in a damp cloth and place it
in a plastic bag. Seal the bag shut.
7. Place the sprayer in a safe place out of the sun for shortterm storage.
Startup
1. Remove the gun from the plastic bag.
2. Stir the water into the paint for latex materials. Remove
the hopper cover from the paint hopper and stir the paint
for all other materials.
Clearing the Paint Hose
1. To save paint left in the hose, release the gun trigger lock
and carefully trigger the gun with the spray tip removed
against the inside of the paint container.
3. Check to be sure that the PRIME/SPRAY knob is set to
PRIME and that the pressure is completely reduced.
4. Plug sprayer in and turn the motor switch to ON.
5. Turn the PRIME/SPRAY knob to SPRAY and gradually
turn the pressure control knob clockwise to increase the
pressure.
6. Test the sprayer on a practice piece and begin spraying.
© SprayTECH Corporation. All rights reserved.
2. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
3. Turn the PRIME/SPRAY knob to SPRAY.
4. Turn the pressure control knob slowly until paint starts to
flow into the bucket. As soon as the water or solvent
starts to come into the bucket, release the trigger.
5. Change to clean water or solvent and continue circulating
for another 5 minutes to thoroughly clean the hose, pump
and spray gun.
9
English
6. Turn the pressure control knob counterclockwise to its
lowest setting.
7. Turn the PRIME/SPRAY knob to PRIME.
8. Trigger the gun to remove any pressure which may still be
in the hose.
9. Lock the gun by turning the gun trigger lock so that it is
parallel to the gun body.
10. Turn the motor switch to OFF.
Final Cleanup
6.
Clearing the Gun
1. Remove the spray gun from the paint hose using two
adjustable wrenches.
2. Remove the filter housing from the gun. Place the gun
and the filter assembly into a container of water or solvent
to soak.
3. Cover the paint container and set it aside.
4. Clean the spray tip and gun filter with a soft brush.
Assemble the spray tip in the cleaning position with the
arrow pointing to the back of the gun.
7.
8.
9.
10.
11.
5. Attach the paint hose to the gun and tighten using two
wrenches.
Remove the tip assembly.
Turn the motor to ON.
Turn the PRIME/SPRAY knob to SPRAY.
Turn the pressure control knob clockwise to 1/2 power.
Trigger the gun into the cleaning bucket until the hopper is
empty.
Refill the hopper and continue flushing the system until
the solution coming out of the gun appears clean.
Lock the gun and turn the pressure control knob
counterclockwise to its lowest setting.
Turn the PRIME/SPRAY knob to PRIME.
Remove the hopper from the inlet valve.
Clean the threads of the inlet valve with a damp cloth.
Fill the inlet valve with a light household oil. Slowly
increase the pressure to distribute the oil through the pump.
SP
R
A
Y
PR
1.
2.
3.
4.
5.
IM
E
12. Turn the PRIME/SPRAY knob to SPRAY to distribute the
oil.
NOTE: Proper cleaning and oiling of the pump after
use are the most important steps you can take
to insure proper operation after storage.
13. Turn the pressure control knob counterclockwise to its
lowest setting.
14. Turn the PRIME/SPRAY knob to PRIME.
15. Trigger the gun to remove any pressure which may still be
in the hose.
16. Lock the gun by turning the gun trigger lock so that it is
parallel to the gun body.
17. Turn the motor switch to OFF.
18. Remove and clean the hopper filter in clean water or the
appropriate solvent. Use a soft brush.
19. Return the hopper filter to its postion in the hopper and
replace the hopper on the inlet valve.
20. Wipe the entire unit, hose and gun with a damp cloth to
remove accumulated paint.
6. Turn the motor switch to ON.
7. Unlock gun trigger by turning the gun trigger lock so that it
is parallel to the gun handle.
8. Turn the PRIME/SPRAY knob to SPRAY and point the gun
to the side of the cleaning bucket.
9. Trigger the gun and gradually turn the pressure control
knob clockwise to 1/2 pressure. Continue to trigger the
gun for approximately 30 seconds.
10. Turn the pressure control knob counterclockwise to its
lowest setting.
11. Turn the PRIME/SPRAY knob to PRIME.
12. Trigger the gun to remove any pressure which may still be
in the hose.
13. Lock the gun by turning the gun trigger lock so that it is
parallel to the gun body.
14. Turn the motor switch to OFF.
English
10
© SprayTECH Corporation. All rights reserved.
2. Leave the copper washer under the cap in place.
NOTE: If the copper washer falls out, be sure to
replace it with the same side up. The top will
show the imprint of the end cap, while the
bottom should be perfectly flat to match the
seat in the pump casting.
Follow these procedures when encountering problems
indicated in the troubleshooting section.
Removing and Cleaning the Inlet Valves
1. Be certain that the sprayer is off.
2. Remove the inlet valve assembly using a 27 millimeter
socket or box end wrench.
3. Remove and clean the small spring inside the valve using
a wire hook or tweezers. Replace the spring if it is broken
or worn.
4. Remove the seat and ball assembly using a 3/8 inch allen
wrench.
5. Clean all parts thoroughly. If the ball or seat show any
sign of wear or damage, replace them with new parts.
This carbide ball must seal tightly against its seat for the
valve to function properly.
6. Cover all parts with a thin coat of light oil before
reassembling.
7. Tighten the valve seat securely with the 3/8 inch allen
wrench.
8. Drop in the valve ball.
9. Insert the protector and spring and replace the cap. Be
sure that the copper washer is positioned properly and
that the tongue on the cap fits inside the spring.
10. Tighten the cap securely with an adjustable wrench. Do
not overtighten.
SPRAY
PRIME
NOTE: This spring is manufactured to a very specific
tension. Do not put in an unauthorized
substitute. See the paint pump assembly parts
diagram for the proper replacement part number.
3. Test movement of the valve by pushing on it from the
open end of the valve housing with a screwdriver or the
eraser end of a pencil. It should move about 1/16 of an
inch. If it does not move, it should be cleaned or
replaced.
Cap
Copper Washer
Spring
Ball
NOTE: The inlet valve must be oiled after every job.
This will reduce or eliminate priming problems
the next time the sprayer is used.
Seat
Seal
PRIME
Removing and Cleaning the Outlet Valve
SPRAY
4. Thoroughly clean the valve assembly with water or the
appropriate solvent. Use a small brush.
5. If you have properly cleaned the valve and water drips out
of the bottom, the valve is worn and needs to be replaced.
A properly seated valve filled with water and held vertically
will not drip.
6. Install a new or cleaned valve in the pump block and then
fill the valve with light oil or solvent.
NOTE: Wear on the ball is almost impossible to
detect visually. To test for a worn outlet valve
assembly, turn the pressure control knob
clockwise to its highest setting and run water
only through the sprayer for 10 to 15 minutes
without triggering the gun.
If the valve is defective, the end cap will get
very hot to the touch. If it is functioning
properly, it will stay approximately the same
temperature as the water running through it.
It may be necessary to remove and clean the outlet valve or to
replace parts inside the valve worn out through normal use.
1. Remove the outlet cap with a wrench.
SPRAY
PRIME
Protector
© SprayTECH Corporation. All rights reserved.
11
English
Choosing the Correct Spray Gun Filter
Cleaning the Spray Tip
Use the proper gun filter based on the type of material being
applied as shown below.
1. Flush the gun with solvent immediately after the work is
completed.
2. Oil the sliding pins to prevent them from seizing up.
Should the spray tip become clogged,
reverse the spray tip with the lever and
pull the trigger. Once the obstruction
comes out of the spray tip, release the
trigger, reverse the spray tip back to the
spray pattern setting, and resume
spraying.
Application
Filter
type
0089960
Synthetic resin,
enamels, clean
varnishes, stains
azures
Extrafine 0.084 mm red
0089959
Base coat enamels,
primer enamels,
fillers, marking paints,
textured enamels
Fine
0.140 mm yellow
0089958
Medium
0.315 mm white
0089957
Filler paints,
large area surfaces
Coarse
0.560 mm green
WARNING
Do not attempt to clean the tip with your finger.
Do not use a needle or other sharp pointed instrument to
clean the tip. The hard tungsten carbide is brittle and can
be chipped.
Cleaning the Filter
Mesh
number
Color of
Filter
body
Clean the filter with a brush dipped in solvent. Never poke the
filter with a sharp instrument.
Changing the Filter
Cleaning the Hopper Screen
1. Pull the trigger guard forward
so that it comes loose from
the handle.
Gun Housing
2. Unscrew the handle from the
Filter
housing and remove the old
filter.
Handle
3. Slide the new filter, taper end
first, into the gun housing.
4. Replace the handle, washer
and spring. Screw the handle
into the housing until hand-tight. Replace the trigger
guard.
The screen at the bottom of the paint hopper may need
cleaning periodically. Check it every time you add paint.
Remove the screen by pulling it out of the hopper with a pliers.
Clean the screen with water or solvent and a soft-bristle brush,
if necessary.
Replacing the Valve Spring Unit
NOTE: Replace the packing if the spray gun is
disassembled. Replace the sliding pins if they
are worn.
Tightening the PRIME/SPRAY Knob
1. Unscrew the spray tip.
2. Lock the gun in the ON position and remove the diffuser
with a wrench
Sometimes the two allen screws holding the PRIME/SPRAY
knob outer cover will vibrate loose. This allows the cover to
turn without changing the valve setting. If this happens,
loosen the screw with a 1/16 allen wrench, turn the knob to
SPRAY and tighten the screw.
Sliding Pin
3. Unlock the gun.
Retainer Block
4. Unscrew the nut
with a wrench
Gun Housing
Nut
and remove the Valve Spring
retainer block.
Unit
5. Remove the
Diffuser
sliding pins with
care and store
them in a safe
place so they will
not be lost.
6. Drive the valve
spring unit forward from the back of the retainer block.
Use the handle of a wooden hammer or similar soft tool to
avoid damaging the valve spring unit.
English
12
© SprayTECH Corporation. All rights reserved.
Troubleshooting
Problem
The sprayer does not start up.
The sprayer starts up but does not
draw in paint when the
PRIME/SPRAY knob is set to
PRIME.
Cause
Solution
1. The sprayer is not plugged in.
2. The ON/OFF switch is set to OFF.
3. Low or no voltage is coming from the
wall plug.
4. The sprayer was turned off while still under
pressure.
5. The extension cord is damaged or has too
low a capacity.
6. The thermal overload on the sprayer is
tripped.
7. There is a problem with the motor.
1. Plug the sprayer in.
2. Turn the ON/OFF switch to ON.
3. Properly test the power supply voltage.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
The unit will not prime properly or has lost prime.
The paint hopper is empty
The hopper filter is clogged.
The inlet valve is stuck.
The outlet valve is stuck.
4. Turn the PRIME/SPRAY knob to PRIME.
5. Replace the extension cord.
6. Allow the motor to cool and move the sprayer to a
cooler spot.
7. Take the sprayer to a SprayTECH Authorized Service
Center.
Try to prime the unit again.
Fill the paint hopper with paint.
Clean the hopper filter.
Clean the inlet valve.
Clean the outlet valve and replace any
worn parts.
Take the sprayer to a SprayTECH Authorized Service
Center.
Replace the inlet valve.
Take the sprayer to a SprayTECH Authorized Service
Center.
Take the sprayer to a SprayTECH Authorized Service
Center.
6. The PRIME/SPRAY valve is plugged.
6.
7. The inlet valve is worn or damage.
8. There is a problem with the diaphragm.
7.
8.
9. The hydraulic oil level is low or empty.
9.
1. The spray tip is worn.
2. The hopper filter is clogged.
3. The gun or spray tip filter is plugged.
4. The paint is too heavy or coarse.
5. The outlet valve assembly is dirty or worn.
6. The inlet valve assembly is damaged or worn.
1. Replace the spray tip with a new tip.
2. Clean the hopper filter.
3. Clean or replace the proper filter. Always keep
extra filters on hand.
4. Thin or strain the paint.
5. Clean or replace the outlet valve assembly.
6. Replace the inlet valve.
The sprayer will not shut off.
1. The inlet or outlet valve ball or ball seat is
worn.
2. Foreign matter or paint has built up between
the ball and the seat.
1. Take the sprayer to a SprayTECH Authorized
Service Center.
2. Take the sprayer to a SprayTECH Authorized
Service Center.
The spray gun leaks.
1. Internal parts of the gun are worn
or dirty.
1. Take the sprayer to a SprayTECH Authorized
Service Center.
The tip assembly leaks.
1. The tip was assembled incorrectly.
2. A seal is worn.
1. Check the tip assembly and assemble properly.
2. Replace the seal.
The spray gun will not spray.
1. The spray tip, the gun filter or the tip filter is
plugged.
2. The spray tip is in the CLEAN position.
1. Clean the spray tip, gun filter or tip filter.
1. The pressure is set too low.
2. The gun, the tip, or the hopper filter
is plugged.
3. The tip is worn.
4. The paint is too thick.
1. Increase the pressure.
2. Clean the filters.
1. The motor overheated.
2. The extension cord is too long or is too
small a gauge.
1. Allow to cool for 30 minutes.
2. Allow to cool for 30 minutes and replace the
extension cord with a shorter extension or a thicker
gauge cord.
3. Clean the paint from the motor.
4. Restart the sprayer in the PRIME mode.
The sprayer draws up paint but
the pressure drops when the gun
is triggered.
The paint pattern is tailing.
The thermal overload tripped and
shut off the sprayer.
3. Paint has built up on the motor.
4. The motor was started while the sprayer
was under pressure.
5. The sprayer was sitting in the hot sun.
2. Put the tip in the SPRAY position.
3. Replace the spray tip.
4. Thin the paint.
5. Move the sprayer out of the sun.
NOTE: When the PRIME/SPRAY valve is on SPRAY and there is flow through the return tube, remove the
PRIME/SPRAY valve and clean or replace it.
NOTE: The electric motor should always be kept clean and dry. Paint acts as an insulator. Too much paint on the
motor will cause the motor to overheat.
© SprayTECH Corporation. All rights reserved.
13
English
Composants
14
SPRAY
PRIME
PRIME
15
ATTENTION
16
SPRAY
Embout
SPRAY
PRIME
AVERTISSEMENT
17
SP
IM
SPRAY
A
Y
SPRAY
PRIME
R
PR
PRIME
PRIME
IM
E
AVERTISSEMENT
R
A
Y
PR
SP
SP
R
A
Y
PR
IM
E
18
Amorçage de la pompe
PRIME
PRIME
SPRAY
SPRAY
PRIME
PRIME
SPRAY
PRIME
ATTENTION
SPRAY
PRIME
PRIME
19
Relâchez
la gâchette
PRIME
PRIME
SPRAY
PRIME
PRIME
SPRAY
20
Rangement à Long Terme
AVERTISSEMENT
SP
R
IM
A
Y
PR
E
22
SPRAY
PRIME
Ressort
PRIME
SPRAY
SPRAY
PRIME
23
Utilisation
Type de
filtre
0089960
Extra-fin
0,084 mm
rouge
0089959
Fin
0,140 mm
jaune
0089958
Moyen
0,315 mm
blanc
0089957
Grossier
0,560 mm
vert
24
Cause
2.
3.
4.
5.
6.
25
Índice
Componentes
26
SPRAY
PRIME
PRIME
PRECAUCION
27
PRECAUCION
Adaptador
28
SPRAY
Pistola cerrada
(pistola no pintará)
SPRAY
PRIME
ADVERTENCIA
29
Cebadura
Para Preparar para Cebar
PRIME
PRIME
IM
SPRAY
A
Y
E
Pistola cerrada
(pistola no pintará)
SP
IM
E
ADVERTENCIA
R
A
Y
PR
PRIME
SPRAY
SP
R
A
Y
PR
IM
PRIME
R
PR
SP
E
30
Montando la Tolva de Pintura
Para Cebar la Bomba
PRIME
PRIME
SPRAY
PRIME
SPRAY
Perilla PRIME/SPRAY
SPRAY
PRIME
PRECAUCION
SPRAY
PRIME
PRIME
31
Para atomizar
Capa ligera
Jale
el gatillo
Manténgala firme
Suelte
el gatillo
Práctica
PRIME
PRIME
Aproximadamente de
10 a 12 pulgadas
PRIME
SPRAY
PRIME
SPRAY
Aproximadamente de
10 a 12
pulgadas
Forma
correcta
Forma
incorrecta
32
Limpieza
AlmacenamIiento Durante la Noche
ADVERTENCIA
33
Limpieza Final
5.
6.
7.
8.
9.
10.
11.
SP
R
A
Y
PR
1.
2.
3.
4.
IM
E
34
SPRAY
PRIME
Tapa
Resorte
PRIME
Sello
SPRAY
SPRAY
PRIME
Bola
35
Tipo de
filtro
0089960
Extrafino
0.084 mm
rojo
0089959
Fino
0.140 mm
amarillo
0089958
Emulsiones, pinturas
de látex, pinturas
acrílicas
Mediano
0.315 mm
0089957
Pinturas de fondo,
superficies de área
extensa
0.560 mm
verde
Para limpiar el filtro
36
37
Parts Listing • Schémas des pièces • Diagramas de las piezas
Final Assembly • Montage final • Ensamble fina
1
24
2
3
25
26
SPRAY
PRIME
4
27
5
28
29
6
7
8
7
9
10
11
12
13
14
15
16
17
30
18
19
20
21
22
23
English
Item
1
2
3
4
Part #
0270311
0288795
0279581
------------
5
6
7
0288796
0288775
0090031
8
9
10
11
12
13
14
0089829
0047393
0288774
0270527
9802279
0089930
0089929
Description
Quantity
Handle ..................................................1
Pin, handle............................................2
Stand ....................................................1
Paint pump assembly
(see separate listing) ............................1
Shroud ..................................................1
Knob, pressure control .........................1
Eccentric sleeve and
bearing assembly..................................1
Key........................................................1
Ring, retaining.......................................1
Gasket ..................................................1
Cover ....................................................1
Screw, cover .......................................12
Seal.......................................................1
Bearing .................................................1
English Français Español
Item
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
38
Part #
9885529
0270231
0089261
0093861
0093709
0270547
0005311
0270548
0089456
0270587
0090628
9921501
9800310
0270314
9802285
0288790
Description
Quantity
Screw, hex, 1/4”....................................1
Housing, hydraulic ................................1
Connector .............................................1
Tube, oil return......................................1
Oil suction tube assembly.....................1
Piston....................................................1
Spring ...................................................1
Washer, piston ......................................1
Ring, retaining.......................................1
Motor.....................................................1
Bumper .................................................1
Lock washer..........................................3
Bolt........................................................1
Crutch tip ..............................................1
Bolt, leg.................................................2
Foot, rubber ..........................................2
© SprayTECH Corporation. All rights reserved.
0288796
0288775
0090031
8
9
10
11
12
13
14
0089829
0047393
0288774
0270527
9802279
0089930
0089929
Pieza #
0270311
0288795
0279581
------------
5
6
7
0288796
0288775
0090031
8
9
10
11
12
13
14
0089829
0047393
0288774
0270527
9802279
0089930
0089929
Pieza #
9885529
0270231
0089261
0093861
0093709
0270547
0005311
0270548
0089456
0270587
0090628
9921501
9800310
0270314
9802285
0288790
English
Item
1
2
1
2
3
3
4
5
6
Part #
0279591
0089917
0088871
0090283
0093865
0090617
0090560
7
0279971
Description
Quantity
Cover, hopper .......................................1
Filter screen, fine (shown) ....................1
Filter screen, coarse
Hopper ..................................................1
Return tube ...........................................1
Fitting ....................................................1
Return tube assembly...........................1
(includes items 4 and 5)
Hopper complete .................................1
(includes items 1 – 6)
4
6
7
0279971
5
7
© SprayTECH Corporation. All rights reserved.
39
0279971
Español Français English
1
2
8
9
10
3
11
12
13
4
14
9
SPRAY
PRIME
15
5
6
16
7
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
English
Item
1
Part #
0270526
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0089482
0281338
0088328
0270951
0270494
0288771A
0089564
9970103
0047485
0093635
0270291
0089494
0270460
0288379
0090617
Description
Quantity
Valve, Inlet Assembly............................1
(includes item 2)
Washer, Sealing, Nylon ........................1
Screw, socket head ..............................4
Lock washer..........................................4
PRIME/SPRAY valve kit .......................1
Ring, diaphragm ...................................1
Diaphragm assembly ............................1
Cap, Outlet Assembly ...........................1
Washer, Sealing, Copper......................2
Spring, Outlet........................................1
Ball, 6mm, Carbide ...............................1
Seat, Ball, Outlet Assembly ..................1
Seal, Outlet ...........................................1
Paint Pump with Valve..........................1
Fitting, Outlet ........................................1
Fitting, Return Tube ..............................1
English Français Español
40
0089482
0281338
0088328
0270951
0270494
0288771A
0089564
9970103
0047485
0093635
0270291
0089494
0270460
0288379
0090617
© SprayTECH Corporation. All rights reserved.
10
9
11
12
8
7
6
5
13
4
3
14
15
2
21
1
16
17
18
19
20
English
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Part #
0297146
0297039
0149342
0149366
0149212
0043211
9922703
0149377
9910403
9930818
9910201
0149368
0149361
0043303
0149370
0034377
0043590
9970123
0347706
0279185
0149211
Description
Quantity
RC tip assembly, 413............................1
Tip guard assembly ..............................1
Diffuser 7/8" ..........................................1
Trigger guard ........................................1
Valve union assembly ...........................1
Packing .................................................1
Snap ring ..............................................1
Pin M-4 .................................................1
Nut, cap M-4 .........................................2
Sliding pin .............................................2
Hex nut .................................................1
Retainer block.......................................1
Gun housing .........................................1
Washer..................................................1
Handle ..................................................1
Filter......................................................1
Spring ...................................................1
Sealing ring...........................................1
Swivel ...................................................1
Collar assembly ....................................1
Trigger assembly ..................................1
© SprayTECH Corporation. All rights reserved.
41
Pieza #
0297146
0297039
0149342
0149366
0149212
0043211
9922703
0149377
9910403
9930818
9910201
0149368
0149361
0043303
0149370
0034377
0043590
9970123
0347706
0279185
0149211
Limited Warranty
Commercial Airless Spray Equipment
Two Year Warranty
Spray Tech, a division of Wagner Spray Tech Corporation ("Spray Tech"), warrants this product against defects in material and
workmanship for a period of two years following the date of purchase by the original purchaser. During that period, Spray Tech
will repair or replace any defective or worn-out component or, at Spray Tech’s option, refund to the original purchaser the full
purchase price for the product in exchange for the return of that product. However, Spray Tech will not replace or repair any fluid
pump component on account of wear more than twice during the two year warranty period. This warranty does not cover
consumable products such as filters and tips.
Lifetime Warranty on Gear Trains, Electric Motors, and Gas Engines
Spray Tech warrants any gear train, electric motor (excluding brushes) and gas engine (excluding the clutch) in this product
against defects in material and workmanship for the lifetime of the original purchaser. If Spray Tech determines that the
foregoing warranty has been breached, Spray Tech will repair or replace the defective components without charge or, at Spray
Tech’s option, refund to the original purchaser the full purchase price for the product in exchange for the return of that product.
Warranty Claims
Any request for repair or replacement pursuant to the warranties above must be accompanied by the return of the applicable
parts, with transportation charges prepaid, to a service center authorized by Spray Tech or to Wagner Spray Tech Corporation,
1770 Fernbrook Lane, Minneapolis, MN 55447.
Limitation of Remedies
THE REMEDIES SET FORTH ABOVE ARE THE EXCLUSIVE REMEDIES AVAILABLE FOR BREACH OF EXPRESS AND
IMPLIED WARRANTIES. These remedies shall not be deemed to have failed of their essential purpose so long as Spray Tech is
willing to repair or replace parts, or to refund the purchase price, as set forth above.
What Is Not Covered By This Warranty
This warranty does not cover defects or damages caused by:
• the use or installation of repair or replacement parts or accessories not manufactured by Spray Tech;
• repair performed by anyone other than a Spray Tech Authorized Service Center; or
• abuse, misuse, negligence, accident, faulty installation or tampering in a manner which impairs normal operation.
This warranty also does not cover equipment and accessories supplied to Spray Tech from an original equipment manufacturer,
including but not limited to hoses, tips, and accessories. Spray Tech will provide the purchaser with copies of the original
equipment manufacturer’s express warranties provided to Spray Tech along with the name and address of the appropriate
manufacturer.
Limitation of Remedies
IN NO CASE SHALL SPRAY TECH BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR
LOSS, INCLUDING TRANSPORTATION COSTS, WHETHER SUCH DAMAGES ARE BASED UPON A BREACH OF EXPRESS
OR IMPLIED WARRANTIES, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL THEORY.
Disclaimer of Implied Warranties
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
No Ability To Transfer
This warranty is extended to the original purchaser only and is not transferable.
SprayTECH 30-Day Satisfaction Guarantee
If, within a 30-day period from the date of purchase, you are not totally satisfied with a SprayTECH/CAPSpray unit, you
may return it for full credit toward another SprayTECH or CAPSpray product of equal or greater value.
Patents
These products are covered by one or more of the following U.S. patents:
5,286,045
D349,711
5,263,789
5,252,210
5,217,238
4,720,801
4,785,719
4,828,464
4,928,722
4,416,588
4,003,504
RE29,055
D376,637
D387,414
D382,938
3,963,180
5,505,381
5,765,753
5,887,793
5,893,522
English
42
D345,841
5,145,331
4,624,602
4,025,045
5,059,099
4,390,324
4,834,287
D405,159
5,084,964
4,403,924
5,073,092
D412,965
© SprayTECH Corporation. All rights reserved.
© SprayTECH Corporation. All rights reserved.
43
D345,841
5,145,331
4,624,602
4,025,045
5,059,099
4,390,324
4,834,287
D405,159
5,084,964
4,403,924
5,073,092
D412,965
44
D345,841
5,145,331
4,624,602
4,025,045
5,059,099
4,390,324
4,834,287
D405,159
5,084,964
4,403,924
5,073,092
D412,965
© SprayTECH Corporation. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed