JT COVERT ASSAULT Owner's manual

FIGURE A
POWER ASSEMBLY
Tubo de energía
Tube de puissance
PULL PIN
Perno
Goupille
*
OWNER’S MANUAL
US PATENTS PENDING
Contains:
• Safety Information
• Warranty Information
• Operating Instructions
MISUSE MAY CAUSE SERIOUS
INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST
BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. RECOMMEND
AT LEAST 18 YEARS OLD TO PURCHASE, 14 YEARS OLD TO USE WITH ADULT
SUPERVISION, OR 10 YEARS OLD TO USE ON PAINTBALL FIELDS MEETING
ASTM-STANDARD F1777-02. READ OPERATION MANUAL BEFORE USING.
WARNING:
NEVER SHOOT AT ANYONE WITHOUT PROPER
PROTECTIVE EQUIPMENT FOR EYES, EARS, THROAT AND HEAD, WHICH
MUST BE WORN AT ALL TIMES. EYE PROTECTION MUST BE DESIGNED
SPECIFICALLY FOR PAINTBALL. FAILURE TO FOLLOW THESE SAFETY
PRECAUTIONS MAY RESULT IN BODILY INJURY INCLUDING BLINDNESS
AND DEAFNESS.
Welcome to the JT SPORTS® team and thank you for purchasing this
high quality JT® paintball marker.
We at JT® stand committed to providing you with the best product and
service available. Your new marker is designed and manufactured to provide
ease of maintenance with trouble free performance. We ask that you read
this manual to obtain the maximum enjoyment and safety of your purchase.
JT Sports LLC.
1201 S.E. 30th St., Bentonville, AR 72712, U.S.A.
Fax (479) 464-8701
www.jtsports.com
RULES OF SAFE
PAINTBALL MARKER HANDLING
1. Always wear proper eye, face and ear protection designed
specifically for paintballs.
2. Never shoot a person who is not wearing proper protection.
3. Treat every paintball marker as if it were loaded.
4. Never look down the barrel of the marker.
5. Never point the paintball marker at anything you don’t wish to shoot.
6. Keep the paintball marker on safe until ready to shoot.
7. Keep the barrel plug in the paintball marker’s muzzle when not shooting.
8. Always remove gas source before disassembly.
9. Store the paintball marker unloaded and degassed in a locked place.
10.Follow warnings listed on gas source for handling and storage.
11.Never use anything other than .68 caliber paintballs.
12.Do not shoot fragile objects such as windows.
13.Paintballs may cause staining of some porous surfaces such as brick,
stucco and wood.
14.Always measure velocity (speed of the paintball before it exits the
barrel) before playing paintball.
15. Never shoot at velocities in excess of 300 feet per second.
16. Never engage in vandalism.
17. Do not use marker for drive-by shootings.
18. Do not modify your marker’s pressurized air system or cylinder in any way.
P/N 143140 - 000 12/09
BARREL
O-RING
DETENT BALL
DETENT SPRING
FILED STRIP PIN
FEEDNECK
O-RING
FIELD STRIP PIN
RECEIVER- LH
HANDLE
SCREW
BOLT
VALVE SLEEVE
LINKAGE ARM
VALVE PLUG
0-RING
Item
VALVE STEM WITH MOLDED CUP SEAL
23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61. 62. 63. VALVE STEM
VALVE SPRING
VALVE BODY
O-RING
STRIKER
REFILLABLE CYLINDER (not included)
Cilindro Rellenable (no incluida)
Cylindre Réutilisable (non fournie)
STEP 4. Adjust the 1/8TH hex velocity screw clockwise/inward until the
screw clears the body of the marker.
STEP 5. Remove the single front grip frame pull pin and top rear grip
frame pull pin. Drop the front of the grip frame down.
STEP 6. Grab the rear cocking house and pull out internals. Do not force
items to come out. Use caution when removing items.
Follow the steps above in reverse order. Lubricate all wear points and
o-rings with minerial oil only.
CONNECTING ROD
RECOCKING HOUSING
DO NOT RETURN THIS MARKER TO YOUR RETAILER.
FOR ASSISTANCE CALL 1-800-755-5061.
WARRANTY INFORMATION
WARRANTY: LIMITED 90 DAY WARRANTY
(ORIGINAL PURCHASE RECEIPT REQUIRED)
For 90 days from date of purchase, JT SPORTS® will repair or replace this
marker free of charge if defective in material or workmanship. This warranty
gives you specific legal rights. You may also have other rights which may
vary from state to state. Service is available from authorized JT SPORTS
Service Centers. A list of these is available at JT SPORTS website at www.
jtsports.com or by calling JT SPORTS® at 1-800-755-5061. These Service
Centers generally offer the quickest service.
If you would rather return your marker to JTSports®
please call customer service at 1-800-755-5061 for return
authorization number and shipping address. (Authorization
number must be visible on outside of shipping package to be
accepted.)
Do not return any products via non-trackable services such as regular
mail or parcel post. Such products may become lost and JT SPORTS® Inc.
will not be responsible for replacement.
PAINTBALL MARKERS OUT-OF-WARRANTY
Call 800.755.5061 or visit our web site at
www.jtsports.com if you should need an Illustrated Parts
List.
Item
1.
2. 3.
4. 5. 6. 7.
8. 9.
10.
11.
12.
13.
14. 15.
16. 17. 18.
19. 20. 21. 22.
FIELD STRIP REASSEMBLY
This safety alert symbol indicates important safety messages in this
manual. When you see this symbol, be alert to the possibility of personal
injury and carefully read the message that follows.
WARNING: THIS IS NOT A TOY.
Use a barrel squeegee to clean broken paintballs from your
marker’s barrel. We recommend the Viewloader® Proflex
Squeegee #5012.
POINTS
LUBRICATION
PUNTOS DE LUBRICACIÓN
TRIGGER
Gatillo para do Dedos
Détente à deux doigts
• Annotated Diagram
• Trouble Shooting Guide
WARNING: DO NOT LOOK DOWN THE BREACH OR BARREL OF
THE MARKER WHILE GAS SOURCE IS ATTACHED. WHEN PROPERLY INSTALLED
THE BARREL PLUG PROTECTS YOU AND EVERYONE WITHIN RANGE. USE
THE BARREL PLUG WHENEVER YOU ARE NOT ACTIVELY ENGAGED IN A
PAINTBALL GAME.
SAFETY
Seguro
Sécurité
COVERT
ASSAULT
.68 CALIBER PAINTBALL MARKER
*
Authorized Service Centers will gladly repair any markers out of warranty
for a nominal charge to cover parts and labor. Repairs made by Service
Centers will usually be faster and less expensive than those sent back to
the factory. Go to www.jtsports.com/service for service center locations
near you. Prior to shipping out of warranty markers, you
must first call customer service at 1-800-755-5061 for return
authorization number and shipping address. (Authorization
number must be visible on outside of shipping package to be
accepted.) Any out of warranty Marker returned to JT SPORTS® must be
shipped prepaid and include the repair fee. Please call the Customer Service
number for current repair fees. JT Sports® will repair or replace the marker
with a reconditioned unit of the same model. If payment is not included,
you will be billed for the repair fee plus a $4.00 invoicing fee. Upon receipt
of payment, the marker or its replacement will be shipped to you. In the
event that the marker includes no means of contacting the sender or no
payment for repairs is received within 60 days of billing, the ownership of
the marker will be forfeited and it will be disposed of at the discretion of JT
SPORTS® LLC.
SPECIAL INSTRUCTIONS
Maintenance/Operation
Follow all procedures listed in this manual. In addition, periodically check
the steel braided hose assembly for leaks or fraying.
Safety
Do not allow the steel braided hose to be pinched in any way. The hose
is durable but is not intended to act as a trigger guard.
NOTE: Follow the “Unloading your Marker” instructions in this owner’s
manual.
FIELD STRIP GUIDE
Bolt and Striker Removal
STEP 1. EYE PROTECTION:
Make sure everyone within range (200 yards) is properly protected from
paintball impacts.
STEP 2. Remove gas supply from marker.
STEP 3. Make sure cocking bolt is in the forward position. Pull trigger to
release if necessary.
FIGURE B
STEP 2. Reassemble the Powertube Assembly, connecting rod and Bolt per
the exploded diagram (Figure B) Note: Inspect and lubricate o-rings and bolt
with approved lubricant before reassembly. Should the striker o-ring show
wear or damage replace (use JT Repair kit 0852-00)
DO’S AND DON’TS
OF CARE AND MAINTENANCE
Note: Any cosmetic or mechanical changes to product will void warranty. Follow
these easy points to keep your marker in top shape for years to come.
DO’S
• DO read owners manual thoroughly before using marker and for
complete disassembly and cleaning instructions.
• DO lubricate o-rings using 3 drops of mineral oil in the ASA adapter with each change of gas source (tank), or marker will dry out and
cause it to not recock after the first shot or after rapid firing.
• DO familiarize yourself with the parts drawing prior to any disassembly.
• DO put marker parts on cloth to avoid losing parts or parts falling
down onto dirt or sand when disassembling,
• DO lubricate o-rings with mineral oil immediately after cleaning. See
(Fig. F) for lubrication points.
DON’TS
• DON’T return this marker to retailer. Call 1-800-755-5061.
• DON’T DISASSEMBLE marker if you are unfamiliar with marker main tainence. (Call customer service at 1-800-755-5061 or visit our website
at www.jtsports.com for assistance).
• DON’T use lubricants other than mineral oil. (For questions about
proper lubricants consult the web page or customer service at
1-800-755-5061)
• DON’T immerse marker in water. (Marker parts may be cleaned by
wiping with a soft cloth or paper towel).
OPERATING INSTRUCTIONS
WARNING: Be sure the paintball marker is always pointed in a safe
direction. Read the following operating instructions and WITHOUT
LOADING ANY PAINTBALLS proceed several times through the operating
steps with your paintball marker (dry fire the paintball marker at a safe
target) so that you will be able to operate the marker properly and safely.
STEP 1. EYE PROTECTION: Make sure everyone within range (200
yards) is properly protected from paintball impacts.
STEP 2. PUT ON “SAFE”. Push safety from left to right; no red band
showing. Make sure barrel plug is placed securely in muzzle of marker.
STEP 3. COCK: Cock marker by pulling cocking handle fully back until
locked in rear position. This marker is a semi-automatic marker, which will
re-cock itself after firing when working properly.
STEP 4. ATTACH GAS SOURCE: Marker can be used with refillable
compressed air/N2 cylinder from JT or WGP . This cylinder is not included
with marker.
NOTE: Add 3 drops of mineral oil to the ASA adapter prior to
attaching the refillable cylinder. Check the website at:
www.jtsports.com/service for approved lubricants.
STEP 5. LOAD PAINTBALLS:
A)Insert loader (not included with all packaging) into ball feed port (Fig C)
on the marker. To remove twist and pull upward quickly.
NOTE: The loader to ball feed port fit is purposely tight. (RECOMMEND
Viewloader® QuantumTM, eVLution IITM or RevolutionTM electronic loader)
Fixed Stock
B)Pour paintballs into loader. NOTE: Paintballs FIGURE C (a)
are gravity fed from loader to the marker each
time the trigger is pulled. Too rapid a rate of
fire, broken balls or too many balls in loader
may cause subsequent balls to break and will
adversely affect the paintball marker’s accuracy.
Use a squeegee to clean inside the paintball
marker’s barrel. (RECOMMEND Brass Eagle®,
Viewloader®,JT®, or WGP® brand .68 caliber
paintballs.) Paintballs should be stored in a
cool, dry place in sealed plastic bags.Do
not subject to freezing, excessive heat,
FIGURE C (b)
humidity or store in direct sunlight. These
conditions may cause ball breakage and/
or poor feeding.
STEP 6. Remove barrel plug and take off safe
by pressing safety from right side of paintball
marker until red band is showing.
STEP 7. VERIFY VELOCITY: Verify that the
paintball velocity is below 300 feet per second or
less if required by playing field. Velocity may be
adjusted by turning the velocity adjustment screw
(See Fig B) Using a 1/8TH allen key (included)
turn screw clockwise to decrease velocity and
counterclockwise to increase velocity.
STEP 8. FIRE: Paintball marker is now ready to fire. Push safety left till red
band is showing, the paintball marker is now ready to fire.
WARNING: Never shoot at anyone without proper protective
equipment for eyes, which must be worn at all times. Eye protection must
be designed specifically for paintball use. Failure to follow these safety
precautions may result in bodily injury including blindness and deafness.
ADJUSTABLE FOREGRIP- The grip is repositionable for length (Fig D) and is
designed to improve your grip on the marker during moving and shooting.
Figure D
DUAL RAIL SYSTEM- The rail system is for use with 3/8th dove tail and
7/8th (Picanny style) rail accessories. The 3/8 th system is commonly used for
.22 and airgun type accessories. The 7/8th Picanny style is use with military
and large caliber firearms type accessories. Note: Check all local, state and
federal laws, as well as with field owners to make sure your marker accessories are suitable for paintball play. These accessories may include
tactical flashlights, sighting systems, bipod, foregrip and carry handle.
(Not included in all models)
INSTALLATION:
STEP 1.
STEP 2.
STEP 3.
handle.
STEP 4.
Remove carry handle set screw with included 1/8th hex key
Remove both rear grip frame pull pins.
Attach fixed stock. Note: stock lock tab will insert under carry
Reinstall pull pins and carry handle set screw.
WARNING: All paintball markers are considered to be loaded until
demonstrated to be unloaded by following the steps for unloading your marker.
UNLOADING YOUR MARKER
Do not store or transport your marker with gas source/tank attached. Do
not store or transport your marker in the cocked position
Description
PIN
SHAFT - RECOCKING
BUMPER
RECOCKING HOUSING
SPRING RECOCK
WASER RECOCK
C - RING - SHAFT
BUMPER
HAMMER SPRING
SCREW
RECEIVER - RH
SET SCREW
BALL STOP
SCREW
SQUARE NUT
FOREGRIP
SCREW
PIN
O-RING
CONNECTOR HORIZONTAL
SCREW WASHER
SCREW
O-RING
SAFETY
TRIGGER RAIL- LH
SPRING
TRIGGER
PIN
INTERRUPTOR
SEAR
TRIGGER RAIL- LH
PIN
GRIP FRAME
BOTTOMLINE ADAPTER
SCREEN FILTER
O-RING
PRESSURE HOSE
GRIP PANEL
STOCK HANDLE
PLATE - BUTT STOCK
Symptom
Cause
Solution
Loader Is Not Functioning
\Or Is Losing Maximum
Performance
Depleted Or
Low Batteries
Replace Batteries
Loader Is Not Operating
Broke Paint In
Properly
The Loader
Clean The Loader
I Have Replaced Batteries
Damaged Electronics And Cleaned My Loader
And It Still Will Not Operate
Visit A Local Service
Center Or Contact
JT For Assistance At
800-755-5061
The Loader jams
Leave Some Room For Ball Movement When
Firing The Loader
Too Many Paintballs In
The Loaderor low
quality out of round paintballs
WARNING: Always wear proper eye, face and ear protection
designed especially to stop paintballs while unloading your paintball marker.
STEP 1. Make sure barrel plug is securely in barrel.
STEP 2. Put Marker on safe. (Push left to right)
STEP 3. Remove loader.
STEP 4. Turn marker upside down to remove paintballs from feed port.
STEP 5. Remove barrel.
STEP 6. Point marker toward ground in a safe direction and fire several
times to insure it is completely unloaded. Put marker back on safe.
STEP 7. Remove gas source.
STEP 8. Use squeegee to dislodge any paintballs from barrel and replace
barrel plug.
STEP 9. Replace barrel. Do not unload your marker indoors.
WARNING: Do not look down the breach or barrel of the marker
while gas source is attached. When properly installed the barrel plug
protects you and everyone with in range. Use the barrel plug whenever
you are not actively engaged in a paintball game.
International Service Center List
South Africa:
Paintball City South Africa
P O Box 3090
Symridge 1420
27.11.828.7583
FAX: 27.11.828.7516
[email protected]
www.paintballcity.co.za
New Zealand:
Kilwell Sports
490 Te Ngae Road Rotorua
64.7.345.9094
FAX:64.7.345.5149
[email protected]
www.kilwell.co.nz
Canada:
PBL Action Sports
7155 Rte Transcanadienne
St-Laurent, Quebec Canada,
H4T 1A2
Tel#-1-888-595-5993
Fax#-514-595-5571
www.buypbl.com
[email protected]
Europe:
JT Europe GmbH
Am Strassbach 1
61169 Friedberg/Hessen
Germany
Phone: +49-(0)60317375-0
www.jt-europe.com
Brazil
Mercenarios
Rua Roma, 620
C.J. 124A
Sao Paulo SP 05050-090
55.11.3871.1468
mercenarios@mercenarios.
com.br
www.mercenarios.com.br
Japan
K2 Japan Corporation
A Nishi-Sando Yamaki Bldg
3 28 6 Yoyogi Shibuya-ku
Tokyo 151-0053
81.3.3320.7822
FAX: 81.3.3320.8771
Contiene:
RÈGLES DE SÉCURITÉ POUR LE MANIEMENT
D’UN MARQUEUR DE PAINTBALL
MANUEL DU PROPRIÉTAIRE
CONTENU:
NO LO DEVUELVA AL VENDEDOR MINORISTA.
LLAME AL, 1-800-755-5061 INFORMACIÓN DE GARANTÍA
GARANTÍA: GARANTÍA LIMITADA DE 90 DÍAS (SE REQUIERE
PRESENTACIÓN DE RECIBO DE COMPRA ORIGINAL)
PISTOLAS DE PAINTBALL FUERA DE GARANTÍA
NE PAS RAMENER CE MARQUEUR À VOTRE REVENDEUR.
COMPOSER LE
1-800-755-5061 INFORMATIONS SUR LA GARANTIE
GARANTIE LIMITÉE DE 90 JOURS (NÉCESSITE LE REÇU
D’ACHAT D’ORIGINE)
GUÍA PARA EL DESARME EN EL CAMPO
REARMADO EN EL CAMPO
REEMPLAZO DEL TUBO DE ENERGÍA
DESARMADO / LIMPIEZA DEL RETÉN DE BOLAS
LANCEURS DE PAINTBALL AVEC GARANTIE EXPIRÉE
GUIDE DE DÉMONTAGE DE CAMPAGNE
REMONTAGE DE CAMPAGNE
QUÉ HACER Y QUÉ NO HACER
DURANTE EL CUIDADO Y EL MANTENIMIENTO
CHOSES À FAIRE ET À NE PAS FAIRE
POUR L’ENTRETIEN ET LES RÉPARATIONS
Symptôme Cause
Solution
Crosse fixe
DÉCHARGER VOTRE MARQUEUR
Síntoma
Causa