Ultra Reef UKS-160, UKS-200, UKS-180 Instruction manual
PDF
Download
Document
Advertisement
Advertisement
ULTRA REEF www.ultrareef.it MANUALE ISTRUZIONI INSTRUCTION MANUAL MANUEL D ‘INSTRUCTIONS BEDIENUNGSANLEITUNG MANUAL DE INSTRUCCIONES UKS-160/180/200 IT · EN · FR · DE · ES V.2015.09 1 ULTRA REEF www.ultrareef.it 2 ULTRA REEF www.ultrareef.it MANUALE ISTRUZIONI 1. INTRODUZIONE 2. AVVIO 3 ULTRA REEF www.ultrareef.it 4 ULTRA REEF www.ultrareef.it Fully open the flow valve rotating the regulation screw and remove the collection cup. INSTRUCTION MANUAL Warning: For more information and details on this product, refer to manuals available on the site www.ultrareef.it before start up product. Warning: In case of flow valve jam, remove discharge screw support and identify the source of the problem. After system installation, it has becomes full responsibility of the user to evaluate the tightness, the effectiveness and suitability of product. Any loss of water and consequent damage remains responsibility of the user. Warning: Prior to start, open the air screw until the screw protrudes 25 mm. In this position, the air is completely open. A wrong adjustment could seriously damage the pump. Warning: The use of the product implies acceptance of all conditions contained in the manual "Safety and Warranty" and it implies previous reading and total understanding. Turn on the pump and check the operation of the product. Clean thoroughly with water and vinegar (diluted to 10%) each component that will go into contact with water. Products that contains alcohol or solvents can damage the acrylic. Continue to operate the skimmer without the cup and wait for the formation of a foam layer of about 1-2cm sufficiently compact in the upper part of the body. 1. OVERVIEW Warning: Consistent emission of air from the exhaust is perfectly normal. It may take several hours or days to stabilize the skimmer at first start. 2. START UP 1- Cover 2- Cup 3- Neck 4- Cup drain 5- Body 6- Diffusor 7- Pump 8- Venturi 9- Flow valve screw 10- Air regulation screw 11- Silencer 12- Air hose To increase or decrease the foam level open or close the flow valve as shown on the regulation screw. Warning: The adjustment must be done with little variation over time. Allow at least 30 minutes after each full turn of the regulation screw. Close the flow valve until the foam reaches the top of the skimmer without overflowing. Warning: The skimmer is designed to work only with salt water (salinity 35%). Replace the cup and cover. For the first week, the cup will fill up quickly and debris collected will be light in colour. Place the skimmer inside the sump tank in a comfortable and easily accessible position. After about a week, the collected liquid should become definitely darker and should accumulate more slowly. Warning: Adjust the water level in the sump to about 22 cm. Keep stable water level by use of high quality osmocontroller. Warning: In just set up tanks, the skimmer may not produce foam for a few weeks. This inhibition is due to the residues of the oils used for the realization of the hoses (rubber hoses). Warning: Make sure the sump is able to contain the water drainage in the event of a blackout. 5 ULTRA REEF www.ultrareef.it Every week: Remove the cup and the cover and wash them thoroughly under running water. If necessary, clean with a wet cloth the internal side of conical part of the skimmer body, without removing it from the sump. 3. SETTING Skimmers are often subject to malfunctions related to the situation of the tank. These phenomena are normal and usually does not pose a risk to the tanks. Every month: Check that the silencer is free from salt encrustation and dirt or algae do not block the Venturi. Warning: To solve of any problems during use, refer to the complete manual. Every 6 months: perform complete control by removing the skimmer from the sump and taking it apart. Carefully check the state of wear of the pump. Increase the level (close the valve) to accelerate the skimming if the amount of liquid collected in the cup is too dense or insufficient. This is commonly referred to as "wet skimming". Conversely, decreased the level (open the gate) to reduce the skimming if the glass is filled too quickly and the accumulated fluid is too light. This is commonly referred to as "dry skimming". Warning: Finding the right point of skimming is extremely difficult and requires some experience. For the first time it is normal to have difficulty regulating the product. It is possible to act on the air adjustment screw to increase or decrease the amount of air treated. Rotate the adjusting screw clockwise to decrease the intake of air. Otherwise, rotate the adjusting screw in an anti-clockwise to increase the air intake. Warning: air regulation recommended only for EXPERTS users, an improper adjustment may limit the performance of the skimmer or seriously damage the pump. It is advisable to empty the glass as soon as the liquid level reaches 2-3cm harvest, which should occur at least weekly. 4. MAINTENANCE Before performing any maintenance, disconnect the product from power supply. Do not use abrasive products, toxic and unsuitable for cleaning operation. 6 ULTRA REEF www.ultrareef.it MANUEL D ‘INSTRUCTIONS le bon 1. INTRODUCTION 7 ULTRA REEF www.ultrareef.it 8 ULTRA REEF www.ultrareef.it 1. EINFÜHRUNG 9 ULTRA REEF www.ultrareef.it bei der 10 ULTRA REEF www.ultrareef.it MANUAL DE INSTRUCCIONES 11 ULTRA REEF www.ultrareef.it 12">

Public link updated
The public link to your chat has been updated.
Advertisement