Remington RM1015P, RM0815P Specification

®
telescoping electric
chainsaw/polesaw
MORM0815P, P
IMPORTANT: Read and understand this manual before assembling or
operating this appliance. Improper use of this appliance can cause
severe injury or death. Keep this manual for future reference.
769-08112 P00
03/12
DO NOT RETURN THIS PRODUCT
NO DEVUELVA ESTE PRODUCTO
NE RAMENEZ PAS CET APPAREIL AU MAGASIN
Please call the Customer Support Department or visit our website for assistance:
Llame al Departamento de Atención al Cliente o visite nuestro sitio Web para solicitar asistencia:
Pour obtenir de l’aide, veuillez appeler le service à la clientèle ou visitez notre site web :
U.S. - EE.UU. - aux États Unis
Canada - Canadá - au Canada
or - o - ou
1-866-206-2707
1-877-696-5533
www.remingtonpowertools.com
DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR
WARRANTY SERVICE.
For assistance regarding the assembly, controls, operation or maintenance of the unit, please call the Customer
Support Department. Additional information about the unit can be found on our website.
For service, please call the Customer Support Department to obtain a list of authorized service dealers near
you. Service on this unit, both within and after the warranty period, should only be performed by an authorized
and approved service dealer. When servicing, use only identical replacement parts.
INTRODUCTION
Your Remington Telescoping Pole Saw is a dual purpose product. The electric chain saw is a separate
operating unit when not assembled to the telescoping pole. Before operating either the chain saw or
the pole saw, make certain you read and understand all Important Safety Information.
Contents
IMPORTANT SAFETY INFORMATION................................................................................4
UNPACKING.........................................................................................................................7
PRODUCT IDENTIFICATION ..............................................................................................8
CHAIN SAW TERMS AND DEFINITIONS ...........................................................................9
CHAIN SAW INFORMATION .............................................................................................10
POLE SAW INFORMATION ..............................................................................................17
CLEANING AND MAINTENANCE ....................................................................................19
STORAGE ..........................................................................................................................21
REPLACEMENT PART AND ACCESSORIES ..................................................................21
TROUBLESHOOTING .......................................................................................................22
REPAIR SERVICE .............................................................................................................22
WARRANTY INFORMATION .............................................................................................23
SAVE THESE INSTRUCTIONS
All information, illustrations and specifications in this manual are based on the latest
product information available at the time of printing. We reserve the right to make changes
at any time without notice.
Copyright© 2012 MTD SOUTHWEST INC, All Rights Reserved.
CALIFORNIA PROPOSITION 65
WARNING: Battery posts, terminals and certain finished components
contain lead, lead compounds and chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
Wash hands after handling.
3
IMPORTANT SAFETY INFORMATION
• heavy-duty gloves (wear rubber gloves when
working outdoors)
• steel-toed safety footwear with non-skid
soles
• eye protection such as safety glasses,
goggles, or face screen
• safety hard hat
• ear mufflers or ear plugs
READ ALL INSTRUCTIONS
• hair covering to contain long hair
• face or dust mask (if working in dusty arMake sure you read and understand all
eas)
instructions in Important Safety Infor10.Before cutting, always provide the followmation on pages 4 through 7. Improper
ing:
use of this chain saw can cause severe
• clear work area
injury or death from fire, electrical shock,
• secure footing
body contact with moving chain, or fall• planned retreat path from falling limbs
ing wood.
11.Inspect tree before trimming or cutting
down. Make sure there are no dead limbs or
Before Operating Saw
branches that may fall on you. Make allow1. Read and understand this owner’s manual
ance
for branches to fall freely to the ground.
before operating saw.
2. Watch what you are doing. Use common sense. 12.Do not use pole saw to fell saplings. Use
the chain saw without pole attachment.
Do not operate saw when you are tired.
13.To reduce the risk of electric shock, this
3. Use saw for cutting wood only.
saw has a polarized plug (one blade is wider
• Do not use chain saw for purpose not inthan the other). This plug will fit in a polartended.
ized outlet only one way. If the plug does
• Do not use for cutting non-wood items.
not fit fully in the outlet of your extension
4. Only well-instructed adults should operate saw.
cord, reverse the plug. If it still does not fit,
Never allow children to operate saw.
a polarized extension cord will be neces5. Use only electrical voltage noted on model
sary. Do not change the plug in any way.
plate of saw.
6. Use only extension cords marked for outdoor WHILE Operating Saw
use. See page 21 for extension cord require1. Stay alert. Use common sense while operating
ments.
saw.
7. Do not operate saw
2. Keep work area clean. Cluttered areas invite
• while under the influence of alcohol, medicainjuries.
tion, or drugs
3. Be aware of extension cord while operating
• in rain or in damp or wet areas
chain saw. Be careful not to trip over cord.
• where highly flammable liquids or gases are
Keep cord away from chain and operator at
present
all times.
• if pole or saw is damaged, adjusted wrong, or 4. Keep children, animals, and bystanders away
not fully and securely assembled
from chain saw and extension cord. Only chain
• if trigger does not turn saw on and off. Chain
saw user should be in work area.
must stop moving when you release trigger. 5. Do not use the pole saw to cut down trees. Use
Have faulty switch replaced by authorized
the chain saw without pole attachment and
service center.
only if you are trained or have expert help.
WARNING: When using an electric
chain saw, basic safety precautions
should always be followed to reduce
the risk of fire, electric shock, and injury
to persons, including the following:
6. Do not use near power lines. Keep at least 10
while in a hurry
feet away from electrical lines.
while in tree or on a ladder
7. If two or more persons perform bucking and
while on aerial booms, buckets, or platforms
felling operations at the same time, provide
Wear snug-fitting clothes when operating chain
plenty of distance between operations. Provide
saw. Do not wear loose clothing or jewelry.
distance of at least twice the height of tree being
They can get caught in moving saw chain.
felled.
9. Wear the following safety gear when operating 8. Secure wood you are cutting by using clamps
saw:
or chocks.
•
•
•
8.
4
iMPORTANT SAFETY INFORMATION
This Saw
This saw has a low-kickback chain and reduced
kickback guide bar. Both items reduce the chance
of kickback. Kickback can still occur with this
saw.
Follow assembly instructions on page 10. Do not
remove front hand guard. Do not replace front
hand guard with substitute.
The following steps will reduce the risk of kickback:
• Use both hands to grip saw while saw is
running
9. Grip chain saw firmly with both hands. Never
WARNING: Some dust created by
operate chain saw with one hand. Never use
hand guard as handle.
power sanding, sawing, grinding, drill10.Grip pole saw securely. Place one hand on the ing, and other construction activities
pole and the other on the handle.
contains chemicals known (to the state
11.Keep finger off trigger until ready to make of California) to cause cancer, birth decut.
fects, or other reproductive harm. Some
12.Before starting chain saw, make sure chain is examples of these chemicals are:
not touching anything.
• lead from lead-based paints
13.To guard against electrical shock, avoid body
• crystalline silica from bricks and cecontact with grounded objects such as pipes,
ment and other masonry products
fences, and metal posts.
•
arsenic and chromium from chemi14.Keep all parts of body away from chain when
cally-treated lumber
saw is running.
15.Do not force saw while cutting. Apply light
pressure. It will do the job better and safer at Your risk from these exposures varies,
depending on how often you do this
the rate for which it was intended.
16.Do not cut small brush and saplings with the type of work. To reduce your exposure
pole saw. Use the chain saw only, with extreme to these chemicals: work in a well venticare. Slender matter may catch in the chain and lated area, and work with approved safety
be whipped toward you. This could also pull equipment, such as those dust masks
you off balance.
that are specially designed to filter out
17.When cutting limb or tree trunk that is under microscopic particles.
tension, use extreme caution. Be alert for
wood springing back. When wood tension is
released, limb could spring back and strike Kickback
operator causing severe injury or death.
WARNING: Kickback may occur when
18.Carry saw from one place to another
the nose or tip of the guide bar touches
• with saw stopped and unplugged
• Chain saw - by holding front handle (never an object, or when the wood closes in
use hand guard as handle)
and pinches the saw chain in the cut.
• Pole saw - with telescoping pole returned to Tip contact in some cases may cause a
shortest position
lightning fast reverse reaction, kicking the
• Pole saw - by holding the pole at the balance guide bar up and back towards the operapoint (close to saw end)
tor. Pinching the saw chain along the top
• with finger off trigger
of the guide bar may push the guide bar
• with guide bar and chain to rear
rapidly back towards the operator. Either
of these reactions may cause you to lose
WARNING: This product contains
control of the saw which could result in
chemicals known to the State of Caliserious injury to user.
fornia to cause cancer or birth defects,
or other reproductive harm.
Kickback Safety Devices On
iMPORTANT SAFETY INFORMATION
Maintenance and Storage of
Saw
• For chain saw, use firm grip. Thumbs and
fingers must wrap around saw handles.
• For pole saw, have one hand gripping the
handle and the other gripping the pole. Use
firm grip. Thumbs and fingers must wrap
around pole and handle.
• Use both hands to grip saw while saw is
running. Use firm grip. Thumbs and fingers
must wrap around saw handles.
• Keep all safety items in place on saw. Make
sure they work properly.
• Chain saw - do not overreach or cut above
shoulder height.
• Pole saw - do not overreach or extend arms
above shoulder height.
• Keep solid footing and balance at all
times.
• Stand slightly to left side of saw. This keeps
your body from being in direct line with
chain.
• Do not let guide bar nose touch anything
when chain is moving (see Figure 1).
• Never try cutting through two branches at
same time. Only cut one log at a time.
• Do not bury guide bar nose or try plunge cut
(boring into wood using guide bar nose).
• Watch for shifting of wood or other forces
that may pinch chain.
• Use extreme caution when reentering a previous
cut.
• Use low-kickback chain and guide bar supplied with this chain saw. Only replace these
parts with chains and guide bars listed in this
manual.
• Never use dull or loose chain. Keep chain
sharp with proper tension.
1. Unplug saw from power source:
• when not in use
• before moving from one place to an
other
• before servicing
• before changing accessories or attachments,
such as saw chain and guard
2. Inspect saw before and after each use. Check
saw closely if guard or other part has been damaged. Check for any damage that may affect
operator safety or operation of saw. Check for
alignment or binding of moving parts. Check
for broken or damaged parts. Do not use saw
if damage affects safety or operation. Have
damage repaired by authorized service center.
3. Maintain saw with care:
• Never expose saw to rain.
• Keep chain sharp, clean, and lubricated
for better and safer performance.
• Follow steps outlined in this manual to
sharpen chain.
• Keep handles dry, clean, and free of oil
and grease.
• Keep all screws and nuts tight.
• Inspect power cord often. If damaged,
have repaired by authorized service cen
ter.
• Never carry saw by power cord.
• Never yank power cord to unplug it.
• Keep power cord from heat, oil, and sharp
edges.
• Inspect extension cords often and re
place if damaged.
Saw Maintenance and Kickback 4. When servicing, use only identical replacement parts.
Safety
5. When not in use, always store saw:
Follow maintenance instructions in this manual.
• in a high or locked place, out of children’s
Proper cleaning of saw and chain and guide bar
reach
maintenance can reduce chances of kickback.
• in a dry place
Inspect and maintain saw after each use. This will
• in a carrying case or with scabbard over guide
increase the service life of your saw.
bar
Note: Even with proper sharpening, risk of kick• drain oil after each use and before storing saw
back can increase with each sharpening.
to prevent oil leakage.
Save these instructions. It is your guide to safe
and proper operation of this saw.
Direction
90°
Do Not Let
Guide Bar
Touch Here
Figure 1 - Kickback Hazard Example: Do Not
Let Nose of Guide Bar Touch Object While
Chain is Moving
iMPORTANT SAFETY INFORMATION
Pole Saw Trimming
Precautions
ENGLISH
Do not use the pole saw to cut limbs
larger in diameter than the length of the
guide bar.
Never stand directly under the limb you
are trimming. Always position yourself out
of the path of falling debris.
Keep other persons away from cutting end
of pole saw and at a safe distance from
work area.
Do not use pole saw near cable, electric
power or telephone lines. Maintain a minimum clearance of 10 feet from all power
lines.
Never stand on a ladder or other type of
unstable support while using the pole
saw.
Always use both hands to operate pole
saw. Keep a firm, steady pressure on the
pole saw while cutting but do not try to
force the saw through the wood.
IMPORTANT: Read and understand this
manual before assembling or operating
this chain saw. Improper use of saw can
cause severe injury. Keep this manual
for future reference.
UNPACKING
1. Remove all items from carton.
2. Check all items for any shipping damage. If
you find any damage or if any parts are missing,
call 1-866-206-2707 (in Canada, call 1-877696-5533).
PRODUCT IDENTIFICATION
CHAIN SAW - All Models
Front Hand
Guard
Rear
Handle
Saw
Chain
Sprocket
Cover
Oil Level Sight Hole (located on
left side of saw body, between
front handle and front hand
guard)
Oil Cap With Squeeze
Bulb
Rear Hand
Guard
Power
Cord
Scabbard
Front
Handle
Spike
Trigger
Trigger
Lockout
POLESAW
Models: RM0815P, RM1015P
Motor Housing
Saw
Chain
Hand Guard
Oil Cap
Power Cord
Clamping
Lever
Inner Pole
Outer Pole
Trigger
Lockout
Tighten
Grip
Area
Trigger
Handle
Power
Cord
Pole Bracket,
Lock Washer,
Adjustment
Knob
Loosen
CHAIN SAW TERMS AND DEFINITIONS
Pushback (Kickback, Pinch) Rapid pushback
of chain saw. Pushback may occur if chain along
top of guide bar is pinched, caught, or contacts a
foreign object.
Rear Handle Handle located at rear of saw
body.
Reduced Kickback Guide Bar Guide bar that
reduces chance of kickback.
Replacement Chain Chain that complies with
ANSI B175.1 when used with a specific saw. It
may not meet ANSI requirements when used with
other saws.
Saw Chain (Chain) Loop of chain having
cutting teeth for cutting wood. The motor drives
chain. The guide bar supports chain.
Spiked Bumper (Spike) Pointed teeth at front
of saw body beside guide bar. Keep spiked bumper
in contact with wood when felling or bucking. It
helps maintain position of saw while cutting.
Sprocket Toothed wheel that drives chain.
Switch Device that completes or interrupts
electrical circuit to motor of saw.
Switch Linkage This device connects switch
to trigger. It moves switch when you squeeze
trigger.
Trigger Switch Lockout Device that reduces
accidental starting of saw.
Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns
saw off.
Trimming (Pruning) Process of cutting limb(s)
from a living tree.
Undercut An upward cut from underside of log
or limb. This is done while in normal cutting position and cutting with top of guide bar.
Bucking Process of cutting a felled tree or log
into lengths.
Clamping Lever Lever is loosened to allow
inner pole to be adjustd and tighted to hole pole
in position.
Felling Process of cutting down a tree.
Felling Cut Final cut when felling a tree. Make
this cut on opposite side of tree from notching
cut.
Front Handle Located at front of saw body.
Front Hand Guard Shield between front
handle and guide bar. Protects left hand while
using saw.
Guide Bar Metal bar that extends from saw
body. The guide bar supports and guides chain.
Guide Bar Nose Tip or end of guide bar.
Inner Pole The moveable section of tubing to
which the saw is attached.
Kickback Quick backward and upward motion
of guide bar. Kickback may occur when tip of
guide bar touches an object while chain is moving. The guide bar will kick up and back towards
operator.
Limbing Process of cutting limb(s) from a
felled tree.
Low-Kickback Chain Chain that reduces chance
of kickback as required by ANSI B175.1.
Normal Cutting Position Stance used while
making bucking and felling cuts.
Notching Cut Notch cut in tree that directs
fall of tree.
Oiler Control System for oiling guide bar and
chain.
Outer Pole Retains the moveable inner pole.
Power Head Chain saw without chain and guide
bar. Also known as saw body.
Chain Saw Information
Chain Saw HardwarE
The plastic hardware bags should include the
following:
• (2) Guidebar bolts
• (2) Guidebar nuts
• (1) Phillips self tapping screw
• (1) Saw chain
• (1) Guide bar
• (1) Hand guard
• (1) Scabbard
6.
7.
Chain Saw Assembly
8.
Assemble the chain saw before assembling the
pole.
Note: Some models are pre-assembled. Assembly
is not needed on these models.
See Saw Chain Tension Adjustment, page 11.
9.
WARNING: Cutting edges on chain
are sharp. Use protective gloves when
handling chain.
IMPORTANT: Make sure to insert adjusting
block into oval adjusting hole on guide bar.
Line up holes on sprocket support with center
slot on guide bar and holes in saw body.
Insert guide bar bolts through front hand guard,
saw body, center slot of guide bar, and sprocket
support. Attach guide bar nuts to guide bar
bolts.
IMPORTANT: Tighten guide bar nuts finger
tight only. Make sure adjusting block is in oval
adjusting hole on guide bar.
Place chain around drive sprocket, then along
top groove of guide bar and around guide bar
nose. Note: Make sure cutting edges of chain
are facing the right direction. Position chain
so cutting edges on top of guide bar face guide
bar nose (see Figure 2).
Adjust saw chain tension. Follow steps under
Saw Chain Tension Adjustment, page 11.
CAUTION: Do not place chain on saw
backwards. If chain is backwards, saw will
vibrate badly and will not cut.
IMPORTANT: Do not clamp chain saw in
vise during assembly.
Adjusting Block
1. Lay chain out flat.
2. Install front hand guard onto saw body. Do this
by pressing two mounting stand-outs on hand
guard into hex-shaped holes in saw body (see
Figure 2).
Towards Guide Bar Nose
Adjusting
Plate
Adjusting Screw
Front Hand Guard
Sprocket Support
Tapping
Screw
Guide Bar
Bolts
Mounting
Stand-Outs
Cutting Edge
Figure 3 - Part Locations For Assembling Guide
Bar
Saw
Chain
Guide
Bar
Adjusting
Hole
Guide Bar Nuts
Drive Sprocket
Figure 2 - Assembling Guide Bar, Chain, and
Hand Guard
3 Insert tapping screw through hand guard and
into saw handle. Tighten screw firmly.
4. Turn adjusting screw counterclockwise (see
Figure 3). Continue to turn adjusting screw
until adjusting block is to rear of adjusting
plate.
5. Install guide bar onto saw body. Place rear of
guide bar between adjusting plate and sprocket
support.
10
Chain Saw Information
Saw Chain Tension Adjustment
Tapping
Screw
Guide Bar
Bolts
Mounting
Stand-Outs
WARNING: Cutting edges on chain
are sharp. Use protective gloves when
handling chain.
Cutting Edge
Saw Chain
Guide Bar
Adjusting
Hole
Guide Bar Nuts
Drive Sprocket
WARNING: Maintain proper chain
tension always. A loose chain will increase the risk of kickback. A loose chain
may jump out of guide bar groove. This
may injure operator and damage chain. A
loose chain will cause chain, guide bar,
and sprocket to wear rapidly.
Figure 4 - Assembling Guide Bar, Chain, and
Hand Guard
Adjusting Plate
Adjusting Block
Adjusting
Screw
Note: For pre-assembled models, the saw chain
tension is properly set at factory. A new chain will
stretch. Check new chain after first few minutes of
operation. Allow chain to cool down. Follow steps
below to readjust saw chain tension.
1. Before adjusting chain, make sure guide bar
nuts are only finger tight (see Figure 4). Also
make sure adjusting block is in oval adjusting
hole on guide bar (see Figures 4 and 5).
2. Turn adjusting screw clockwise. (see Figure
6). Note: There should be no gap between side
links of chain and bottom of guide bar (see
Figure 7).
3. Wearing protective gloves, move chain around
guide bar. Chain should move freely. If chain
does not move freely, loosen chain by turning
adjusting screw counterclockwise.
4. After chain tension is correct, tighten guide
bar nuts firmly. If not, guide bar will move and
loosen chain tension. This will increase the risk
of kickback. This can also damage saw. Note: A
new chain will stretch. Check new chain after
first few minutes of operation. Allow chain to
cool down. Read just chain tension.
Sprocket Support
Figure 5 - Part Locations For Assembling
Guide Bar
Figure 6 - Turning Adjusting Screw
Guide Bar Nuts
Gap
Correct
Tension
Incorrect
Tension
Figure 7 - Saw Chain Adjustment
11
WARNING: Unplug chain saw from
power source before adjusting saw chain
tension.
Towards Guide Bar Nose
Front Hand Guard
Chain Saw Information
Extension Cords
3. Replace oil cap at once. Tighten oil cap firmly
for good seal. This will minimize oil seepage
from tank.
Use proper extension cords with this saw. Use 4. Wipe off excess oil.
only extension cords marked for outdoor use.
Note: It is normal for oil to seep when saw
The cord must be marked with suffix W or W-A
following the cord type designation. Example:
is not in use. Empty oil tank after each
SJTW-A or SJTW.
use to prevent seepage.
Use proper sized cord with this saw. Cord must
be heavy enough to carry current needed. An
undersized cord will cause voltage drop at saw.
Saw will lose power and overheat. Follow cord
size requirements listed below.
Cord
Length
AWG Cord
Size
50 feet
16 AWG
25 feet
100 feet
150 feet
16 AWG
Oiling Chain
Always check oil level before using saw. Do not
attempt to operate the oil system while saw is
in operation. To oil chain, press squeeze bulb.
Oil will feed onto the guide bar and chain. Press
squeeze bulb at least once before each cut (see
Figure 9). Check oil level often by looking at
oil sight level hole. Oil sight level hole is on left
side of saw, between front handle and front hand
guard.
16 AWG
14 AWG
Keep cord away from cutting area. Make sure cord
does not catch on branches or logs during cutting.
Figure 9 - Pressing Squeeze Bulb on Oil Cap
Inspect cords often. Replace damaged cords.
to Oil Chain
The extension cord may come undone from the
power cord during use. To avoid this, make a knot Cutting with the Chain Saw
with the two cords as shown in Figure 8.
1. Connect saw to extension cord. Connect extension cord to power supply.
Chain Saw Power Cord
2. Make sure section of log to be cut is not laying
on ground. This will keep chain from touching
ground as it cuts through log. Touching ground
with moving chain will dull chain.
3. Use both hands to grip saw. Always use left
Extension Cord
hand to grip front handle and right hand to grip
rear handle. Use firm grip. Thumbs and fingers
must wrap around saw handles (see Figure 10,
page 13).
Figure 8 - Tying Extension Cord and Power
4. Make sure your footing is firm. Keep feet
Cord in Knot
apart. Divide your weight evenly on both
feet.
5. When ready to make a cut, press in trigger
Filling Oil Tank
lockout with right thumb and squeeze trigger
1. Remove oil cap.
(see Figure 10, page 13). This will turn saw
2. Fill oil tank with SAE #30 motor oil. Note:
on. Releasing trigger will turn saw off. Make
For temperatures below 30°F, use SAE #10 oil.
sure saw is running at full speed before starting
For temperatures above 75°F, use SAE #40 oil.
a cut.
6. When starting a cut, place moving chain
against wood. Hold saw firmly in place to
IMPORTANT: Do not use "bar and
avoid possible bouncing or skating (sideways
chain" oil. It is too thick and may not
movement) of saw.
oil properly.
12
Felling is the process of cutting down a tree. Make
sure your footing is firm. Keep feet apart. Divide
your weight evenly on both feet. Follow directions
below to fell a tree.
Trigger
Lockout
1. Before felling, inspect tree. Make sure there
are no dead limbs or branches that may fall
on you. Study natural lean of tree, location of
larger branches, and wind direction. This will
help you judge which way tree will fall.
2. Clear work area around tree.
3. Plan and clear a retreat path before felling.
Make retreat path opposite to planned direction
of fall of tree and at 45° angle
(see Figure 11 ).
Trigger
Figure 10 - Trigger Lockout and Trigger
Location
7. Guide saw using light pressure. Do not force
saw. The motor will overload and can burn out.
It will do the job better and safer at the rate for
which it was intended.
8. Remove saw from a cut with saw running
at full speed. Stop saw by releasing trigger.
Make sure chain has stopped before setting
saw down.
9. Practice until you can maintain a steady, even
cutting rate.
FELLING A TREE
(Cutting Down a Tree)
Retreat
Path
45°
Direction of
Fall
Tree
Retreat
Path
Figure 11 - Retreat Path From Tree
4. Remove dirt, stones, loose bark, nails, staples,
and wire from tree where you will make felling
cuts.
5. Stay on uphill side when felling tree. Tree
could roll or slide downhill after falling.
WARNING:
•Avoid kickback. Kickback can result in severe injury or death. See
Kickback, page 5, to avoid risk of
kickback.
• Do not fell a tree without ample skill
or expert help.
• Keep children, animals, and bystanders away from area when felling a
tree.
• If two or more persons perform bucking and felling operations at the same
time, provide ample distance between
operations. Provide distance of at
least twice the height of tree being
felled.
WARNING: When felling a tree, be
aware of your surroundings. Do not
endanger any person, strike utility lines,
or cause property damage. If tree strikes
utility lines, contact utility company at
once.
13
Before Felling a Tree
Chain Saw Information
Felling Procedure
A) Felling Notch
A properly placed felling notch will determine
direction tree will fall. Place felling notch on
side of tree in direction you want tree to fall (see
Figure 12). Follow directions below to create a
felling notch.
1. Make lower notch cut as close to ground as
possible. Hold saw so guide bar is horizontal.
Cut 1/3 the diameter of tree trunk (see Figure
12). Note: Always make this horizontal lower
notch cut first. If you make this cut second, tree
can pinch chain or guide bar.
2. Start upper notch cut the same distance above
first cut as first cut is deep.
Example: If lower notch cut is eight inches
deep, start upper notch cut eight inches above
it. Cut downward at 45° angle. The upper
notch cut should meet end of lower notch cut
(see Figure 12).
3. Remove tree trunk wedge created by notching
cuts.
3. As felling cut nears hinge, tree should begin to
fall. Note: If needed, drive wedges into felling
cut to control direction of fall. If tree settles back
and pinches chain, drive wedges into felling cut
to remove saw. Only use wedges made of wood,
plastic, or aluminum. Never use wedge made of
steel. This could cause kickback and damage to
chain.
4. When tree begins to fall, quickly
• remove saw from felling cut
• release trigger to turn saw off
• put saw down
• exit area using retreat path
WARNING: Be alert for falling overhead limbs. Watch your footing while
exiting area.
Direction of Fall
3rd Cut Felling Cut
Hinge
2nd Cut Upper Notch
Cut
2"
2"
1st Cut Lower Notch
Cut
Figure 12 - Felling A Tree
B) Felling Cut
1. Make felling cut two inches higher than lower
notch cut and on opposite side of tree (see
Figure 12). Keep felling cut parallel to lower
notch cut.
2. Cut towards notch.
WARNING: Do not cut all the way
through tree. Leave about two inches
of tree diameter uncut directly behind
felling notch (see Figure 12). This uncut
portion acts as a hinge. The hinge helps
keep tree from twisting and falling in
wrong direction.
14
Chain Saw Information
Bucking A Log
Limbing a Tree
WARNING: When cutting limb that
is under tension, use extreme caution.
Be alert for wood springing back. When
wood tension is released, limb could
spring back and strike operator causing
severe injury or death.
Bucking a log is cutting a log into sections. Make
sure your footing is firm. Keep feet apart. Divide your
weight evenly on both feet. When possible, raise log
or section off ground. Do this by using limbs, logs,
chocks, etc.
When cutting through log, maintain control by
reducing cutting pressure near end of cut. Do not
relax your grip on chain saw handles. Do not let
moving chain touch ground. Ground will dull moving chain. After cutting through log, release trigger
to turn saw off before moving saw.
Follow directions below to buck a log.
Limbing is removing branches from a fallen tree.
Make sure your footing is firm. Keep feet apart.
Divide your weight evenly on both feet. Do not
remove larger limbs under tree that support log
off ground. Remove each limb with one cut (see
Figure 13). Clear cut limbs from work area often.
This will help maintain a safe work area.
Make sure you start your cut where limb will
not pinch saw during cutting. To avoid pinching,
start cut on freely hanging limbs from above
limb. Start cut on limbs under tension from under
limb. If pinch occurs, turn saw off, lift limb, and
remove saw.
Entire Length Of Log On Ground
Cut log from top (see Figure 14).
Figure 14 - Bucking Log With Entire Length
On Ground
Figure 13 - Limbing A Tree
15
WARNING: Avoid kickback.
Kickback can result in severe injury
or death. See Kickback, page 5, to
avoid risk of kickback.
WARNING: Avoid kickback. Kickback can result in severe injury or death.
See Kickback, page 5, to avoid risk of
kickback.
Chain Saw Information
WARNING:
Trimming a Tree (Pruning)
WARNING: Avoid kickback. Kickback
can result in severe injury or death.
See Kickback, page 5, to avoid risk of
kickback.
• If on slope, make sure log will not
roll down hill. Secure log by using
wooden stakes. Drive wooden stakes
into ground on downhill side of log.
Stand on uphill side of log while cutting. Log may roll after cutting.
• Never try cutting through two logs
at same time. This could increase
the risk of kickback.
•While cutting log, never hold log with
your hand, leg, or foot.
•While cutting log, never allow another person to hold log.
•Turn off and unplug saw before moving from one place to another.
WARNING: Do not operate pole
saw while:
• in a tree
• on a ladder or any other unstable
surface
• in any awkward position
You may lose control of pole saw causing severe injury.
WARNING: Do not extend arms above
shoulders when using pole saw.
Log Supported On One End
1. Make first cut on underside of log (see Figure
15). Use top of guide bar to make this cut. Cut
1/3 through diameter of log. This cut will keep
section from splintering when cut.
2. Make second cut directly above first cut. Cut
down to meet first cut. This cut will keep log
from pinching guide bar and chain.
CAUTION: Seek professional help if
facing conditions beyond your ability.
Trimming a tree is the process of cutting limbs
from a living tree. Make sure your footing is firm.
Keep feet apart. Divide your weight evenly on
both feet. Follow directions below to trim a tree.
1. Make first cut six inches from tree trunk on
underside of limb. Use top of guide bar to make
this cut. Cut 1/3 through diameter of limb (see
Figure 17).
2. Move two to four inches farther out on limb.
Make second cut from above limb. Continue
cut until you cut limb off.
3. Make third cut as close to tree trunk as possible
on underside of limb stub. Use top of guide bar
to make this cut. Cut 1/3 through diameter of
stub.
4. Make fourth cut directly above third cut. Cut
down to meet third cut. This will remove limb
stub.
2nd
Cut
1st Cut
Figure 15 - Bucking Log When Log Is Supported
On One End
Log Supported On Both Ends
1. Make first cut from above log (see Figure 16).
Cut 1/3 through diameter of log. This cut will
keep section from splintering when cut.
2. Make second cut on underside of log, directly
under first cut. Use top of guide bar to make
this cut. Cut up to meet first cut. This will keep
log from pinching guide bar and chain.
4th Cut
- Final Stub
Cut
2nd Cut - Pruning Cut
(to avoid pinching)
6"
1st Cut
2" to 4"
1st Cut - Pruning
Undercut (to avoid
splintering)
3rd Cut - Stub Undercut
(to avoid splintering)
2nd Cut
Figure 16 - Bucking Log When Log Is Supported
Figure 17 - Cutting A Limb
On Both Ends
16
POLE Saw Information
Pole Saw Assembly
RPS2N1
❸
Step
– Attach Handle Bracket
to Pole Bracket
Step
The hardware bag contains the following items:
• (1) Handle Bracket
• (1) Knob
• (1) .250" Lock Washer
❶ – Squeeze Trigger
3A Slide handle bracket onto
clamping bolt.
1B Squeeze and hold
trigger.
3B
1A Push in and hold trigger lockout
button.
Step
Saw
2A
Clamping bolt should extend through
handle bracket.
❹
Step
– Secure Handle Bracket
to Pole Bracket
4A Place lockwasher onto
clamping bolt.
❷ – Insert Pole Bracket into
Continue to hold trigger while
completing step 2B.
EN
HT
IG
T
4B Thread knob onto clamping bolt. Note:
After knob makes contact with handle
bracket, tighten 1 1/2 to 2 more turns.
Step
❺ – Connect to Power Cord
Plug saw power cord into receptacle cord at end
of inner pole.
2B
Insert pole bracket into saw. Note: Pole
Bracket holds trigger in “ON” position.
17
POLE Saw Information
Adjusting Pole Length
RPS2N1
The Remington RPS2N1 Pole Saw has a telescoping pole assembly that will extend from 57 inches
(fully retracted) to 96 inches (fully extended). A
cam levered collet is used to hold the pole in position at any extended length.
1. To extend the pole, loosen the clamping lever
(see Figure 18). Pole will slide freely.
2. Pull inner pole section out to desired length of
extension. Note: Only extend pole to minimum
length required to reach limb that is being
cut.
3. To lock pole in position, tighten clamping lever
(see Figure 18).
Grip Area
Figure 19 - Designated Grip Areas
UNLOCK
LOCK
Figure 18 - Extending Telescopic Pole
Cutting with the Pole Saw
1. Connect saw to extension cord. Connect extension cord to power supply.
2. Use both hands to grip pole saw. Use only
designated grip areas when operating pole
saw (see Figure 19). Use firm grip. Thumbs
and fingers must wrap around pole saw handle
and pole.
Trigger
3. Make sure your footing is firm. Keep feet
Lockout
apart. Divide your weight evenly on both feet.
4. When ready to make a cut, press in trigger
lockout and squeeze trigger (see Figure 20).
Trigger
This will turn pole saw on. Releasing trigger
Figure
20
Pole
Saw Handle with Trigger
will turn pole saw off. Make sure saw is running
Lockout
at full speed before starting a cut.
5. When starting a cut, place moving chain
against wood. Hold pole saw firmly in place to
avoid possible bouncing or skating (sideways
movement) of saw.
6. Guide pole saw using light pressure. Do not
force pole saw. The motor will overload and
can burn out. It will do the job better and safer
at the rate for which it was intended.
7. Remove pole saw from a cut with saw running at full speed. Stop pole saw by releasing
trigger. Make sure chain has stopped before
setting pole saw down.
18
CLEANING AND MAINTENANCE
NOTICE: These are instructions for servicing your chain saw. Any servicing
not mentioned should be done by an
authorized service center.
Guide Bar Groove
Cleaning Saw Body
WARNING: Unplug chain saw from
power source before servicing. Severe
injury or death could occur from electrical shock or body contact with moving
chain.
WARNING: Cutting edges on chain
are sharp. Use protective gloves when
handling chain.
WARNING: When cleaning saw
body,
• do not submerge saw in any liquids
• do not use products that contain
ammonia, chlorine, or abrasives
• do not use chlorinated cleaning
solvents, carbon tetrachloride, kerosene, or gasoline
Keep saw body clean. Use a soft cloth dampened
with a mild soap and water mixture. Wipe saw
body to clean.
Guide Bar With
Uneven Wear
Figure 21 - Guide Bar Cross Section Showing
Uneven Bar Wear
Normal Guide Bar Maintenance
1. Remove guide bar from chain saw.
2. Remove sawdust from guide bar groove periodically. Use putty knife or wire (see Figure
22).
3. Clean oil slots after each day of use.
4. Remove burrs from sides of guide bar. Use flat
file to make side edges square.
Replace guide bar when
• bar is bent or cracked
• inside groove of bar is badly worn
Note: When replacing guide bar, see Replacement
Parts and Accessories.
Burr
Care of Guide Bar
Uneven bar wear causes most guide bar problems.
Incorrect sharpening of chain cutter and depth
gauge settings often cause this. When bar wears
unevenly, it widens guide bar groove (see Figure
21). This causes chain clatter and rivet popping.
Saw will not cut straight. Replace guide bar if
this occurs.
Flat
File
Cleaning Groove With Putty Knife
Inspect guide bar before sharpening chain. A
worn or damaged guide bar is unsafe. A worn or
damaged guide bar will damage chain. It will also
make cutting harder.
Oil Slot
Figure 22 - Guide Bar Maintenance
19
CLEANING AND MAINTENANCE
Sharpening Saw Chain
Filing Direction
30° Guide
Mark
Keep chain sharp. Your saw will cut faster and
more safely. A dull chain will cause undue sprocket, guide bar, chain, and motor wear. If you must
force chain into wood and cutting creates only saw
dust with few large chips, chain is dull.
HOLDER
WARNING: Cutting edges on chain
are sharp. Use protective gloves when
handling chain.
FILE
WARNING: Unplug chain saw from
power source before servicing. Severe
injury or death could occur from electrical shock or body contact with moving
chain.
File
Guide
5/32" Round
File
Note: This illustration shows file guide placement and
filing direction for sharpening cutters on left side of
chain.
Filing Cutter Depth Gauges
The cutter depth gauge clearance is reduced as
cutters are sharpened. After every second or third
sharpening, reset cutter depth gauges.
1. Place depth gauge tool (.025") firmly across
top of two cutters. Make sure depth gauge enItems Needed to Sharpen Chain
ters slot in depth gauge tool (see Figure 25).
Purchase these items from your local dealer, hard- 2. Use medium flat file. File depth gauge level with
ware store, or chain saw supplies outlet.
depth gauge tool.
• 5/32" round file
3. Remove depth gauge tool. With flat file, round
off front corner of cutter depth gauge (see Figure
• Depth gauge tool
26).
• File guide
After several hand filings, have authorized service
• Vise
center or sharpening service machine sharpen
chain. This will insure even filing.
• Medium sized flat file
Sharpening Cutters
Depth Gauge (right side
Depth Gauge (left sideof chain)
Use file guide for 30° filing.
Groove
of chain)
1. Adjust chain for proper tension (see Saw Chain
Groove
Tension Adjustment, page 11).
Top Plate (left
2. Clamp guide bar in vise to hold saw steady.
side of chain)
Top Plate (right
Note: Do not clamp chain.
side of chain)
3. Press 5/32" round file (attached to file guide)
Right Side of Chain
into groove between top plate and depth gauge
on chain. File guide should rest on both top plate Figure 24 - Chain Part Locations
Depth
and depth gauge (see Figure 23). Note: File at
Gauge
midpoint of guide bar.
4. Hold file guide level. Make sure 30° mark on
Flat File
file guide is parallel to center of guide bar (see
Depth Gauge
Figure 23). This will insure that you file cutters
Tool
at 30° angle.
5. File from inside towards outside of cutter
Depth Gauge Slot
until sharp. Only file in this one direction (see
Figure 23). Note: Two or three strokes with
Figure 25 - Depth Gauge Tool On Chain
file should sharpen cutter.
Front Corner
6. After each cutter is sharpened, move chain
forward to sharpen next cutter. File all cutters
.025"
on one side of chain.
7. Move to other side of chain and repeat process.
Figure 26 - Round Off Front Corner Of Depth
Gauge
20
CLEANING AND MAINTENANCE
Replacing Saw Chain
T
Replace chain when cutters are too worn to
sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include
new drive sprocket when replacing chain. This
will maintain proper driving of chain. Note: For
proper chain and drive sprocket, see Replacement
Parts and Accessories.
Replacement Parts
And accessories
STORAGE
If storing saw for more than 30 days, follow steps
below:
1. Drain oil tank after each use.
2. Remove and clean guide bar and chain. Clean
guide bar and chain by soaking in petroleum
based solvent or mild soap and water mixture.
3. Dry guide bar and chain.
4. Place chain in container filled with oil. This
will prevent rust.
5. Wipe a thin coating of oil over surface of guide
bar.
6. Wipe off outside of saw body. Do this with soft
cloth dampened with a mild soap and water mixture.
7. Store chain saw
• in a high or locked place, out of children’s
reach
• in a dry place
WARNING: Use only replacement
parts and accessories described in this
manual. Use of other parts or accessories
could damage saw or injure operator.
For original replacement parts and accessories,
call 1-866-206-2707 (in Canada call 1-877-6965533) or visit www.remingtonpowertools.com.
21
TROUBLESHOOTING
Note: For additional help, visit www.remingtonpowertools.com.
WARNING: Unplug chain saw from power source before servicing. Severe injury or death could occur from electrical shock or body contact with
moving chain.
OBSERVED FAULT
POSSIBLE CAUSE
REMEDY
Saw runs, but does not cut
Chain assembled backwards
on guide bar
See Chain Saw Assembly, page 10
Saw does not cut unless heavily Chain is dull
forced. Cutting produces only
sawdust with few large chips
See Sharpening Saw Chain, page 20
Saw runs slow. Saw stalls Low power supply voltage
easily
Extension cord wire size too small. See
Extension Cords, page 12
Motor of saw does not run
when you squeeze trigger
1. Trigger lockout not pressed
in to release trigger
2. Extension cord connections loose
3. Open line fuse or circuit breaker
4. Worn out motor brushes
5. Open wiring circuit on saw
1. Press in trigger lockout before
squeezing trigger
2. Check cord connections
3. Check line fuse or circuit breaker
4. See authorized service center
5. See authorized service center
Motor of saw runs, but chain
does not move
Drive Sprocket Failure
Remove and Inspect Drive Sprocket
for damage
Chain does not get oil
1. Clogged oil slot in guide bar
2. Oil is too thick
1. Remove guide bar and clean oil
slot
2. Use correct weight of oil. See
Filling Oil Tank, page 12
Chain comes off guide bar
1. Chain is loose
1. Tighten chain. See Saw Chain Tension Adjustment, page 11
2. See Chain Saw Assembly, page 10
2. Guide bar and chain not
assembled correctly
Saw smokes
Saw damaged. Do not use saw
See authorized service center
Saw leaks oil
It is normal for oil to seep
when the saw is not in use.
Note: Empty oil tank when not in use
repair SERVICE
Note: Only use original replacement parts. This will protect your warranty coverage for parts
replaced under warranty.
For service, please call the Customer Support Department to obtain a list of authorized service
dealers near you. Service on this unit, both within and after the warranty period, should only be
performed by an authorized and approved service dealer.
Call 1-866-206-2707 (in Canada call 1-877-696-5533) or visit www.remingtonpowertools.com.
22
WARRANTY INFORMATION
MANUFACTURER’S LIMITED WARRANTY FOR:
REMINGTON LLC
P.O. Box 361032
Cleveland, OH 44136
23
The limited warranty set forth below is given by Remington LLC (“Remington”) with respect with new
merchandise purchased and used in the United States, its possessions and territories.
Remington warrants this product against defects in material and workmanship for a period of two (2)
years commencing on the date of original purchase and will, at its option, repair or replace, free of charge,
any part found to be defective in material or workmanship. This limited warranty shall only apply if this
product has been operated and maintained in accordance with the Operator’s Manual furnished with the
product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper
maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster.
Damage resulting from the installation or use of any accessory or attachment not approved by Remington
for use with the product(s) covered by this manual will void your warranty as to any resulting damage.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE THROUGH
YOUR LOCAL AUTHORIZED SERVICE DEALER. To locate the dealer in your area, visit our website at
www.remingtonpowertools.com, check for a listing in the Yellow Pages, call 1-866-206-2707 or
1-877-696-5533 in Canada, or write to P.O. Box 361032, Cleveland, OH 44136. No product returned
directly to the factory will be accepted unless prior written permission has been extended by the
Customer Service Department of Remington.
This limited warranty does not provide coverage in the following cases:
A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters
B. Wear items - Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes,
Drive Belts, Saw Chains, Guide Bars, Cultivator Tines.
C. Remington does not extend any warranty for products sold or exported outside of the United
States of America, its possessions and territories, except those sold through Remington’s
authorized channels of export distribution.
Remington reserves the right to change or improve the design of any Remington Product without
assuming any obligation to modify any product previously manufactured.
No implied warranty, including any implied warranty of merchantability or fitness for a particular
purpose, applies after the applicable period of express written warranty above as to the parts as
identified. No other express warranty or guaranty, whether written or oral, except as mentioned
above, given by any person or entity, including a dealer or retailer, with respect to any product shall
bind Remington. During the period of the Warranty, the exclusive remedy is repair or replacement
of the product as set forth above. (Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.)
The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from
the sales. Remington shall not be liable for incidental or consequential loss or damages
including, without limitation, expenses incurred for substitute or replacement lawn care
services, for transportation or for related expenses, or for rental expenses to temporarily
replace a warranted product. (Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.)
In no event shall recovery of any kind be greater than the amount of the purchase price of the product
sold. Alteration of the safety features of the product shall void this Warranty. You assume the risk and
liability for loss, damage, or injury to you and your property and/or to others and their property arising
out of the use or misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original purchaser, original lessee or the
person for whom it was purchased as a gift.
How State Law Relates to this Warranty: This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
To locate your nearest service dealer dial 1-866-206-2707 in the United States or 1-877-696-5533 in Canada.
®
SIERRA ELÉCTRICA
SIERRA ELÉCTRICA
DE PÉRTIGA TELESCÓPICA
MANUAL PARA EL USUARIO
769-08112 P00
03/12
24
INTRODUCCIÓN
Contents
INFORMACIÓN IMPORTANTE DE SEGURIAD..................................................................................26
DESEMBALAJE...................................................................................................................................30
IDENTIFICACIÓN DEL PRODUCTO...................................................................................................31
TÉRMINOS Y DEFINICIONES DE LA SIERRA DE CADENA ............................................................32
INFORMACIÓN SOBRE LA SIERRA DE CADENA............................................................................33
INFORMACIÓN SOBRE LA SIERRA DE PÉRTIGA ...........................................................................40
LIMPIEZA Y MANTENIMIENTO ..........................................................................................................42
ALMACENAMIENTO ...........................................................................................................................44
ACCESORIOS Y PIEZAS DE REPUESTO .........................................................................................45
SERVICIO DE REPARACIÓN .............................................................................................................45
DIAGNÓSTICO Y RESOLUCIÓN DE PROBLEMAS ..........................................................................46
PROPOSICIÓN 65 DEL ESTADO DE CALIFORNIA
25
INFORMACIÓN DE GARANTÍA ..........................................................................................................47
INFORMACIÓN IMPORTANTE DE SEGURIDAD
27
29
INFORMACIÓN IMPORTANTE DE SEGURIDAD
PRECAUCIONES PARA PODAR CON
LA SIERRA DE PÉRTIGA
IDENTIFICACIÓN DEL PRODUCTO
SIERRA ELÉCTRICA
Extremo frontal,
barra de guía
Mango
posterior
Cadena
serrada
Tapa del Aceite con
Ampolla de Apriete
Mango Frontal
Púa
Pértiga Exterior
Ajustar
Área de Agarre
31
Aflojar
32
Borde de
corte
Cadena
serrada
Borde de
corte
Cadena
serrada
Gap
35
Traba de seguridad
2"(5 cm)
2do corte:
Muesca superior
1er corte:
Muesca inferior
37
INFORMACIÓN SOBRE LA SIERRA DE CADENA
DESMEMBRAMIENTO DE UN ÁRBOL
2do corte
1er corte
2do corte
6"
(15 cm)
PODA DE UN ÁRBOL
Figura 17 - Poda de una rama
39
1er corte
INFORMACIÓN SOBRE LA SIERRA DE CADENA
ENSAMBLE DE LA SIERRA DE
PÉRTIGA
RPS2N1
1B Accione y
sostenga al
gatillo.
EN
HT
IG
T
40
Área de Agarre
DESBLOQUEADO
BLOQUEADO
PARA CORTAR CON LA SIERRA DE
PÉRTIGA
41
Figura 19 - Áreas de Agarre Designadas
Rebaba
CUIDADO DE LA BARRA DE GUÍA
42
LIMPIEZA Y MANTENIMIENTO
AFILADO DE LA CADENA
HOLDER
FILE
ALMACENAMIENTO
44
S
w
c
45
Llame al 1-866-206-2707 (en el Canadá llame al
1-877-696-5533) o visite
www.remingtonpowertools.com.
DIAGNÓSTICO Y RESOLUCIÓN DE PROBLEMAS
Nota: Para obtener más ayuda, visite www.remingtonpowertools.com.
Bajo voltaje de entrada
1. Ranura de aceite obstruida en la
barra de guía
2. Aceite demasiado viscoso
46
INFORMACIÓN DE GARANTÍA
GARANTÍA LIMITADA DEL FABRICANTE PARA:
REMINGTON LLC
P.O. Box 361032
Cleveland, OH 44136
47
®
TRONÇONNEUSE ÉLECTRIQUE PRIME
SCIE ÉLECTRIQUE À PERCHE TÉLESCOPIQUE
MANUEL D'UTILISATION ET D'ENTRETIEN
769-08112 P00
03/12
48
INTRODUCTION
Contents
CONSIGNES DE SÉCURITÉ IMPORTANTES..................................................................50
DÉBALLAGE .....................................................................................................................54
IDENTIFICATION DU PRODUIT........................................................................................55
VOCABULAIRE DE LA TRONÇONNEUSE ......................................................................56
INFORMATION SUR LA TRONÇONNEUSE.....................................................................57
INFORMATION SUR LA TRONÇONNEUSE SUR TIGE...................................................64
NETTOYAGE ET ENTRETIEN...........................................................................................66
REMISAGE ........................................................................................................................68
PIÈCES DE RECHANGE ET ACCRSSOIRES ..................................................................69
SERVICE DE RÉPARATION..............................................................................................69
DÉPANNAGE .....................................................................................................................70
INFORMATION SUR LA GARANTIE ................................................................................71
CONSERVEZ CES INSTRUCTIONS
PROPOSITION DE LOI 65 DE CALIFORNIE
49
FRANÇAIS
CONSIGNES DE SÉCURITÉ IMPORTANTES
•
PENDANT L'UTILISATION DE
LA TRONÇONNEUSE
51
FRANÇAIS
52
CONSIGNES DE SÉCURITÉ IMPORTANTES
ENTRETIEN ET REMISAGE DE LA
TRONÇONNEUSE
FRANÇAIS
CONSIGNES DE SÉCURITÉ IMPORTANTES
MESURES DE PRÉCAUTION ÉBRANCHAGE À L’AIDE DE LA
SCIE À PERCHE
Nez de guidechaîne
Guidechaîne
Chaîne
Éperon
Gâchette
Identification des Composants de la Scie á Perche
MODÈLES: RM0815P, RM1015P
Guide-chaîne
Perche
interne
Support de tige,
Rondelle de
blocage, Bouton
Gâchette
55
Desserrer
FRANÇAIS
56
INFORMATION SUR LA TRONÇONNEUSE
QUINCAILLERIE - TRONÇONNEUSE
Tranchant
Chaîne
FRANÇAIS
Vis
autotaraudeuse
INFORMATION SUR LA TRONÇONNEUSE
RÉGLAGE DE LA TENSION DE LA
CHAÎNE
Tranchant
Chaîne
INFORMATION SUR LA TRONÇONNEUSE
REMPLISSAGE DU RÉSERVOIR
16 AWG
16 AWG
16 AWG
14 AWG
LUBRIFICATION DE LA CHAÎNE
FRANÇAIS
INFORMATION SUR LA TRONÇONNEUSE
SCIAGE AVEC LA TRONÇONNEUSE
ABATTAGE D’UN ARBRE
Verrou d’interrupteur
Gâchette
45°
2"
(5 cm)
2"(5 cm)
FRANÇAIS
INFORMATION SUR LA TRONÇONNEUSE
ÉBRANCHAGE
AVERTISSEMENT :
1st Cut
2nd
Cut
FRANÇAIS
INFORMATION SUR LA TRONÇONNEUSE SUR TIGE
ASSEMBLAGE DE LA SCIE À
PERCHE - RPS2N1
EN
HT
IG
T
1A
1B
3B
64
VERROUILLÉE
COMMENT COUPER À L’AIDE LA
SCIE À PERCHE
65
FRANÇAIS
NETTOYAGE ET ENTRETIEN
Rainure de guide-chaîne
Guide-chaîne normale
Ébarbure
Guide-chaîne
NETTOYAGE ET ENTRETIEN
AFFÛTAGE DE LA CHAÎNE
Lime ronde
de 4 mm
(5/32 po)
67
FRANÇAIS
REMISAGE
Coin avant
.025"
.635 mm
68
NETTOYAGE ET ENTRETIEN
PIÈCES DE RECHANGE ET
ACCESSOIRES
S
S
S
69
FRANÇAIS
DÉPANNAGE
Remarque : Pour toute assistance supplémentaire, visitez
www.remingtonpowertools.com. w
WARNING: Unplug chain saw from power source before servicing. Severe injury or death could occur from electrical shock or body contact with
moving chain.
DÉFAILLANCE
OBSERVÉE
CAUSE POSSIBLE
REMÈDE
70
INFORMATION SUR LA GARANTIE
GARANTIE LIMITÉE DU FABRICANT POUR:
REMINGTON LLC
P.O. Box 361032
Cleveland, OH 44136
71
FRANÇAIS
72
73
74
75