Delfield 407 User manual

Delfield 407 User manual
Work-Top And Undercounter Refrigerator And Freezer Bases
The Delfield Company, Models 402, 403, 406, 407, ST4048 & ST4148
Original User Manual
Manufactured exclusively for
McDonald’s® By:
Delfield
980 S. Isabella Rd.
Mt. Pleasant, MI 48858
Tel. (989) 773-7981 Fax (989) 773-2060
400 & 4000 Series
Work-Top And Undercounter Refrigerator And Freezer Bases
*9294260*
©2013•McDonald’s Corporation
All Rights Reserved
Printed in April, 2013
Printed in
The United States of America
Delfield
™
®
Important Warning And Safety Information
WARNING
Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment.
WARNING
Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death.
WARNING
Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other
Appliance.
WARNING
Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment.
WARNING
This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have
Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For
Their Safety.
WARNING
This Appliance Is Not To Be Played With.
Warning
Do Not Clean With Water Jet.
WARNING
Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance.
CAUTION
Observe the following:
Page 2
•
Minimum clearances must be maintained from all walls and combustible materials.
•
Keep the equipment area free and clear of combustible material.
•
Allow adequate clearance for air openings.
•
Operate equipment only on the type of electricity indicated on the specification plate.
•
Unplug the unit before making any repairs.
•
Retain this manual for future reference.
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Delfield
™
®
Table Of Contents
Serial Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Regulatory Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Stabilizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Caster Or Leg - 400 & 4000 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Caster and Leg Mounting Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation
Refrigerator Temperature Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Evaporator Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Freezer Models 403 & 407 Temperature Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Freezer Model 4148 Temperature Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Daily Inspect & Clean PM Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Quarterly Clean Condenser Coil PM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Quarterly Inspect Door Gaskets PM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
Wiring Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
Replacement Parts Listing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22
Standard Labor Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 3
Delfield
™
®
Serial Number
The Undercounter Refrigerator Serial Tag is located on the interior left side wall. Always have the serial number of your
unit available when calling for parts or service.
Warranty Information
Visit http://www.delfield.com/minisite/service/warranty_info to:
• Register your product for warranty.
• Verify warranty information.
• View and download a copy of your warranty.
Regulatory Certifications
Models are certified by:
National Sanitation Foundation (NSF)
Underwriters Laboratories (UL)
Underwriters Laboratories of Canada (ULC)
Page 4
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Delfield
™
®
Specifications
# of
Shelves
Shelf Area
Storage
Capacity
H.P
R404
Charge
V/Hz/Ph
AMPS
Ship
Weight
Plug Type
402-MD1,
402-DHL-MD1
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
176lbs
(80kg)
NEMA
5-15P
402-MD2,
402-DHL-MD2
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
176lbs
(80kg)
NEMA
5-15P
402-MD3,
402-DHL-MD3
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
176lbs
(80kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
230/50/1
1.8
176lbs
(80kg)
NA
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
176lbs
(80kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
230/50/1
1.8
176lbs
(80kg)
NA
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
6.5oz
(184g)
115/60/1
5.8
184lbs
(83kg)
NEMA
5-15P
403-MD2,
403-DHL-MD2
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
6.5oz
(184g)
115/60/1
5.8
184lbs
(83kg)
NEMA
5-15P
403-MD3,
403-DHL-MD3
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
6.5oz
(184g)
115/60/1
5.8
184lbs
(83kg)
NEMA
5-15P
406-MD1,
406-DHL-MD1
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
406-MD2,
406-DHL-MD2
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
406-MD2-CP2,
406-DHL-MD2-CP2
1
2.3ft2
(.21m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
176lbs
(80kg)
NEMA
5-15P
406-MD2-CP3,
406-DHL-MD2-CP3
1
2.3ft2
(.21m2)
5.7ft3
(.16m3)
1/5
7oz
198g
230/50/1
1.8
176lbs
(80kg)
10A Type I
1
2.3ft2
(.21m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
1
2.3ft2
(.21m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
Model
402-MD4
402-MD5,
402-DHL-MD5
402-MD6
403-MD1
406-MD2-CP5
406-MD2-CP6
406-MD3,
406-DHL-MD3
406-MD4
406-MD5,
406-DHL-MD5
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 5
Delfield
™
®
Specifications, continued
Model
406-MD6
406-MD7
406-MD8
406-MD9
407-MD1
407-MD2
407-MD3,
407-DHL-MD3
ST4048-MD1
ST4048-MD2
ST4048-MD3
ST4048-MD4
ST4148-MD1
ST4148-MD2
Page 6
# of
Shelves
Shelf Area
Storage
Capacity
H.P
R404
Charge
V/Hz/Ph
AMPS
Ship
Weight
Plug Type
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
115/60/1
4.0
172lbs
(78kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
230/50/1
1.8
176lbs
(80kg)
NA
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
230/50/1
1.8
186lbs
(84kg)
NA
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
7oz
(198g)
230/50/1
1.8
172lbs
(78kg)
NA
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
6.5oz
(184g)
115/60/1
5.8
176lbs
(80kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
6.5oz
(184g)
115/60/1
5.8
176lbs
(80kg)
NEMA
5-15P
2
4.6ft2
(.43m2)
5.7ft3
(.16m3)
1/5
6.5oz
(184g)
230/50/1
2.1
176lbs
(80kg)
10A Type I
4
8.0ft2
(.74m2)
10.8ft3
(.31m3)
1/5
7oz
(198g)
115/60/1
4.0
234lbs
(106kg)
NEMA
5-15P
4
8.0ft2
(.74m2)
10.8ft3
(.31m3)
1/5
7oz
(198g)
115/60/1
4.0
234lbs
(106kg)
NEMA
5-15P
4
8.0ft2
(.74m2)
10.8ft3
(.31m3)
1/5
7oz
(198g)
115/60/1
4.0
234lbs
(106kg)
NEMA
5-15P
4
8.0ft2
(.74m2)
10.8ft3
(.31m3)
1/5
7oz
(198g)
115/60/1
4.0
234lbs
(106kg)
NEMA
5-15P
4
8.0ft2
(.74m2)
10.8ft3
(.31m3)
1/3
7oz
(198g)
115/60/1
5.6
242lbs
(110kg)
NEMA
5-15P
4
8.0ft2
(.74m2)
10.8ft3
(.31m3)
1/3
7oz
(198g)
115/60/1
5.6
242lbs
(110kg)
NEMA
5-15P
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Delfield
™
®
Installation
Location
Units represented in this manual are intended for indoor use
only. Be sure the location chosen has a floor strong enough to
support the total weight of the cabinet and contents. Reinforce
the floor as necessary to provide for maximum loading. Take
care when moving the equipment that nothing gets pinched
between the unit and stationary objects. Sheet metal edges,
although deburred, could cause cuts in certain situations.
For the most efficient refrigeration, be sure to provide good air
circulation inside and out.
Inside cabinet: Do not pack refrigerator so full that air cannot
circulate.
Outside cabinet: Be sure that the unit has access to ample
air. A minimum space of 3” (7.6cm) at the back of the unit
and 1” (2.5cm) at the top and sides is required to conform to
Underwriters Laboratories’ standards. On undercounter units
it is imperative that the proper air flow be maintained. The
refrigeration system is designed so air will flow under the unit,
over the compressor/condenser area, and out at the top rear of
the unit. Avoid hot corners and locations near stoves and ovens.
Plumbing
Self-contained models are standard with a condensate
evaporator. If, for some reason, a unit does not have a
condensate evaporator, or the evaporator fails, the unit’s
drain must have an outlet to an appropriate drainage area or
container.
Moisture collecting from improper drainage can
create a slippery surface on the floor and a hazard
to employees. It is the owner’s responsibility to
CAUTION
provide a container or outlet for drainage.
Electrical connection
Refer to the amperage data, the serial tag, your local code or the
National Electrical Code to be sure the unit is connected to the
proper power source. A protected circuit of the correct voltage
and amperage must be run for connection of the line cord, or
permanent connection to the unit.
A 6’ (1.8 m) long grounded supply cord and plug are provided
with standard units. Simply plug the unit in to begin operation.
The thermostat must be turned to OFF and
the unit disconnected from the power source
whenever performing service, maintenance
functions or cleaning the refrigerated area.
Any restriction of the proper air flow outlined
above, total or partial, will void the warranty
on the unit.
If the supply cord is damaged it must be
replaced before operating this equipment. Do
not connect a damaged supply cord to a power
source. The cord must be replaced by a qualified
service personnel.
Leveling
A level cabinet will perform better because the drain pan will
drain properly, the doors will line up with the frames and the
cabinet will not be subject to undue strain.
All four legs are adjustable. Adjust each leg until the unit is
stable and level left to right. If necessary adjusting the front legs
slightly higher than the rear by about 1/8” (0.3cm) will help the
door remain closed.
If the unit is supplied with casters, no adjustments are available.
Ensure the floor where the unit is to be located is level.
Never stand on the unit! Doing so may result in
bodily injury. They are not designed to hold the
weight of an adult and will collapse if misused in
this manner.
Stabilizing
Stacked 400 series electrical connection
Models 406 and 407 may be stacked using a stacking
collar, Delfield model 409. In this case two 6’ (1.8m) long
grounded supply cords and plugs are standard. Simply
plug them in to begin operation.
CAUTION
For Cord Connected Units - Risk of Electric
Shock. This equipment has two power supply
cords. Unplug all cords before moving or
servicing this equipment.
These models are supplied on casters for your convenience, for
ease of cleaning underneath and mobility.
The unit must be installed in a stable condition with
the front wheels locked. Locking the front casters
after installation is the owner’s responsibility. This
will keep the unit from rolling or tipping.
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 7
Delfield
™
®
Caster Or Leg Installation - 400 & 4000 Series
1.Carefully place the unit on its back (see illustration at right).
Plate Casters
W/Locks
2.Located at each caster mounting location are 4 Phillips head
screws, for a total of 16 screws. Remove them.
3.Place a locking plate caster or leg over one of the front holes,
matching the 4 mounting holes to the pre-drilled holes in the
underside of the unit. Insert 4 Phillips head screws and tighten.
Repeat with the other locking front caster or leg.
4.Repeat step 3 with the non-locking casters or legs in the rear
of the unit.
Plate Casters
W/O Locks
Screws
Plate caster installation, 400 & 4000 Series.
5.Carefully lift the unit upright.
WARNING
After installing casters or legs, the unit must stand
upright for twenty-four (24) hours before being
powered up to assure oil return to the compressor
sump.
Caster and Leg Mounting Detail
A universal bolt hole pattern is provided on the bottom of the cabinet. It will accommodate any leg or caster. Simply line up the
plate holes with the corresponding cabinet holes.
2.38”
6cm
2.82”
7cm
3.40”
9cm
Page 8
1.75”
4cm
0.94”
2cm
2.14”
5cm
NOTE:
If hole pattern on caster/leg
matches the one above mount
in outer set of holes.
NOTE:
If hole pattern on caster/leg
matches the one above mount
in middle set of holes.
NOTE:
If hole pattern on caster/leg
matches the one above mount
in inner set of holes.
6” Leg - 3234569
3” Caster - 3234024
5” Caster - 3234161
6” Leg - 3234791
2” Caster - 3234148
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Delfield
™
®
Refrigerator Temperature Control Operation
After the unit is connected to power it will automatically
begin operating. With the doors closed, the temperature
of the cabinet should reach 36°F to 40°F (2°C to 4°C) on
refrigerators in about one hour.
A thermostat located in the evaporator housing on interior
rear of the unit, controls the temperature in the box.
The factory setting for the control is “4” and maintains
about 38°F (3°C) in the box. Set toward “1” for higher
temperatures and toward “7” for lower temperatures.
Service Alert
During normal operation the evaporator fan may cycle
and/or pulse independently of the compressor. Consult
the service manual or contact Technical Support at
1-800-733-8829 if you are unsure of the proper function.
Continuous opening and closing of the doors will hamper the
unit’s ability to maintain optimum refrigeration temperature.
Refrigerators defrost automatically with every cycle of the
compressor. The water generated is routed to a pan on the
rear of the unit and is evaporated by the heat given off by
the compressor.
Evaporator Fan Operation
Cooling Cycle
Compressor On
Evap Fan
On
Evap Fan
Off
Defrost Cycle
Compressor Off
Evap Fan
On
400
Refrigerator
X
400
Freezer
X
4000
Refrigerator
X
X
4000
Freezer
X
X
Evap Fan
Off
X
Compressor Off
Evap Fan
On
X
X
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Evap Fan
Off
X
X
X
Page 9
Delfield
™
®
Freezer Models 403 & 407 Temperature Control Operation
After the unit is connected to power it will automatically
begin operating. With the doors closed, the temperature of
the cabinet should reach 0°F (-18°C) on freezers in about
one hour. Continuous opening and closing of the doors will
hamper the unit’s ability to maintain optimum temperature.
The electronic temperature control constantly monitors
box temperature as well as evaporator coil temperature to
maintain consistent product temperatures. As an added
energy-saving feature, the electronic controller will switch
the evaporator fan motor on and off with the compressor
and condenser fan motor.
At initial start-up or anytime power is disconnected, then
reconnected to the unit, the control will delay all operations
for a short time (up to 10 minutes.) While in this delay
period, the control initializes the control parameters and
confirms that the temperature sensors and circuits are
operational.
Service Alert: During normal operation the evaporator fan
may cycle and/or pulse independently of the compressor.
Consult the service manual or contact Technical Support at
1-800-733-8829 if you are unsure of the proper function.
IMPORTANT NOTE REGARDING FREEZERS:
After initializing, the control will immediately enter a
DEFROST mode. The compressor and condenser fan as
well as the evaporator fan will remain off until initial defrost
is complete. This initial defrost cycle may take up to 15
minutes to complete, at which time the freezing cycle will
begin.
Whenever the freezer is plugged in, and the control has
completed initializing including the initial defrost cycle
(see above), the electronic temperature control will cycle
the compressor, evaporator fan motor, and condenser fan
motor to maintain box temperature at the control setting.
Page 10
Freezer Automatic Defrost
The control also monitors compressor total running time
and will enter a defrost cycle after total compressor running
time is greater than 5-hours since the last defrost cycle OR
if evaporator coil temperature drops below -34°F (indicating
excessive frost on the coil).
Freezer Manual Defrost
If a manual defrost is desired, simply unplug the unit for
several seconds, then plug unit back in. This will cause the
control to re-initialize and then enter a defrost cycle.
When the control enters the defrost mode, whether manual
or automatic, it switches off the evaporator fan motor,
compressor and condenser fan motor, and switches on the
defrost heater to warm the evaporator coil and melt all frost
accumulated during the previous refrigeration cycle. The
control will continue the defrost cycle for a MINIMUM of 8
minutes and a MAXIMUM of 30 minutes depending on the
amount of frost accumulated on the evaporator coil.
After the defrost cycle is complete, the control returns to a
normal refrigeration cycle, however the evaporator fan motor
will not switch on for 2 minutes AFTER the compressor and
condenser fan motor have begun operating.
Electronic Temperature Control Location & Adjustment
Never turn the knob more than 1 dial number and always
allow 8 hours for temperature stabilization before making
any additional adjustments. The control is located in
the control box at the rear of the unit (see photo). It is
factory set at mid-range to maintain about -3°F (-18°C) box
temperature. To adjust for colder temperatures, turn the
knob clockwise. For warmer temperatures, turn the knob
counter-clockwise. Turn the knob fully counter-clockwise to
turn the refrigeration system off.
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Delfield
™
®
Freezer Model 4148 Temperature Control Operation
After the unit is connected to power it will automatically
begin operating. With the doors closed, the temperature of
the cabinet should reach 0°F (-18°C) on freezers in about
one hour.
A thermostat located in the evaporator housing on interior
rear of the unit, controls the temperature in the box.
The factory setting for the control is “4” and maintains
about -3°F (-18°C) in the box. Set toward “1” for higher
temperatures and toward “7” for lower temperatures.
Continuous opening and closing of the doors will hamper the
unit’s ability to maintain optimum refrigeration temperature.
When the mechanical timer initiates a defrost cycle, power to
the condensing unit and evaporator fans is interrupted and
the defrost heater is energized. The defrost heater warms the
evaporator coil thereby melting all frost accumulated during
the previous refrigeration cycle. Once all frost is eliminated,
the temperature of the coil continues to rise until it reaches
27 minutes. The defrost control switches to refrigeration
mode. Defrost will initiate every six hours.
Turn the defrost timer screw ONLY in a
clockwise direction, turning the screw counterclockwise will break the cam motor.
Service Alert
During normal operation the evaporator fan may cycle
and/or pulse independently of the compressor. Consult
the service manual or contact Technical Support at
1-800-733-8829 if you are unsure of the proper function.
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 11
Delfield
™
®
Inspect And Clean
Daily
RF 2 D1
Clean the exterior to prevent discoloration or rust. Clean the interior to keep it food safe.
Time required
5 minutes to prepare
15 minutes to complete
Time of day
At close
For 24-hour restaurants: during low-volume periods
Hazard icons
Tools and supplies
Bucket, clean and
sanitized towels
Bucket, soiled towels
Gloves, rubber
Goggles
EXCEED Glass and
Multi Surface Cleaner
Procedure
1 Unplug power cord. Move
products from inside unit to
walk-in.
2 Wear hand and eye protection.
Wear rubber gloves and
safety goggles when handling
cleaner and sanitizer.
3 Clean exterior with EXCEED.
Spray exterior surfaces with
EXCEED Glass and Multi
Surface Cleaner. Using a
clean towel, wipe unit with
the “grain” of the stainless
steel to avoid marring the
finish.
5 Clean interior with EXCEED.
Remove shelves from interior.
Spray interior, shelves and
gaskets with EXCEED Glass
and Multi Surface Cleaner.
Using a clean towel, wipe
interior, shelves and gaskets.
EXCEED Glass and Multi
Surface Cleaner
6 Sanitize interior.
Wipe interior, shelves and
gasket with a clean, sanitized
towel dampened with McD
Sanitizer solution.
McD Sanitizer Solution
7 Put shelves back into the
cabinet.
Wipe exterior with a clean,
sanitized towel dampened
with McD Sanitizer solution.
Daily
EXCEED Glass and Multi
Surface Cleaner
4 Sanitize exterior.
Delfield Under Counter And Work Top Refrigerator/Freezer 402, 403, 406, 407
Why
8 Plug power cord in. Put
product back into unit.
McD Sanitizer Solution
RF2 D1
#9294285
Page 12
©McDonald’s Corporation · Planned Maintenance Manual · Revised January 2009
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 1 of 1
9294259
Delfield
™
Clean Condenser Coil
Quarterly
RF 2 Q1
In order to maintain proper refrigeration performance, the condenser must be clean.
Time required
5 minutes to prepare
15 minutes to complete
Time of day
At close
For 24-hour restaurants: during low-volume periods
Hazard icons
Tools and supplies
Brush, wire
5/16” Nut driver
Procedure
1 Unplug unit power cord.
5 Plug the unit power cord in.
2 Remove exterior back with
Delfield Under Counter And Work Top Refrigerator/Freezer 402, 403, 406, 407
Why
Vacuum, wet/dry
®
5/16” nut driver.
3 Locate condenser on back of
unit.
4 Clean condenser.
Quarterly
Vacuum or wire brush dust
and particles from condenser.
Remove particles from
cabinet.
RF 2 Q1
#9294285
©McDonald’s Corporation · Planned Maintenance Manual · Revised June 2012
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 1 of 1
Page 13
Delfield
™
Inspect Door Gaskets
®
Quarterly
RF 2 Q2
In order to maintain proper refrigeration performance, the gasket must seal the door to the unit.
Time required
0 minutes to prepare
10 minutes to complete
Time of day
At close
For 24-hour restaurants: during low-volume periods
Hazard icons
None
Tools and supplies
None
Procedure
1 Inspect door gaskets.
Check that the door gaskets
are present.
Check that there is no
space between the unit
frame and the gasket.
Check that the gasket is
tight against the door itself.
Check that there are no
rips, tears, or cracks on any
part of the gasket.
Delfield Under Counter And Work Top Refrigerator/Freezer 402, 403, 406, 407
Why
2 If necessary, order a new
gasket.
Call 1-800-733-8829 to find a
local parts distributor. Have
the model and serial number
available when calling the
distributor.
Quarterly
RF 2 Q2
#9294285
Page 14
©McDonald’s Corporation · Planned Maintenance Manual · Revised January 2009
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 1 of 1
Delfield
™
®
Maintenance
The thermostat must be turned to OFF and
the unit disconnected from the power source
whenever performing service, maintenance
functions or cleaning the refrigerated area.
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and
warm water. If this isn’t sufficient, try ammonia and water
or a nonabrasive liquid cleaner. When cleaning the exterior,
always rub with the “grain” of the stainless steel to avoid
marring the finish.
Do not use an abrasive cleaner because it will scratch the
stainless steel and plastic and can damage the breaker strips
and gaskets.
Cleaning the Condenser Coil
The condenser coil requires regular cleaning, recommended
is every 90 days. In some instances though you may find
that there is a large amount of debris and dust or grease
accumulated prior to the 90 day time frame. In these cases
the condenser coil should be cleaned every 30 days.
If the build up on the coil consists of only light dust and
debris the condenser coil can be cleaned with a simple
brush, heavier dust build up may require a vacuum or even
compressed air to blow through the condenser coil.
If heavy grease is present there are de-greasing agents
available for refrigeration use and specifically for the
condenser coils. The condenser coil may require a spray
with the de-greasing agent and then blown through with
compressed air.
Failure to maintain a clean condenser coil can initially cause
high temperatures and excessive run times, continuous
operation with dirty or clogged condenser coils can result in
compressor failures. Neglecting the condenser coil cleaning
procedures will void any warranties associated with the
compressor or cost to replace the compressor.
cleaner or stiff brush. If extremely dirty, a commercially
available condenser cleaner may be required.
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several
important steps need to be taken. First, we need to
understand the properties of stainless steel. Stainless
steel contains 70-80% iron which will rust. It also contains
12-30% chromium which forms an invisible passive film over
the steels surface which acts as a shield against corrosion.
As long as the protective layer is intact, the metal is still
stainless. If the film is broken or contaminated, outside
elements can begin to breakdown the steel and begin to form
rust of discoloration.
Proper cleaning of stainless steel requires soft cloths or
plastic scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR
SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage the
protective film of the stainless steel. Chlorides are also
commonly found in hard water, salts, and household and
industrial cleaners. If cleaners containing chlorides are
used be sure to rinse repeatedly and dry thoroughly upon
completion.
Routine cleaning of stainless steel can be done with soap and
water. Extreme stains or grease should be cleaned with a
non-abrasive cleaner and plastic scrub pad. It is always good
to rub with the grain of the steel. There are also stainless
steel cleaners available which can restore and preserve the
finish of the steels protective layer.
Early signs of stainless steel breakdown can consist of small
pits and cracks. If this has begun, clean thoroughly and start
to apply stainless steel cleaners in attempt to restore the
passivity of the steel.
Never use a high pressure water wash for this
cleaning procedure as water can damage the
electrical components located near or at the
condenser coil.
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease
regularly. It is recommended that this be done at least every
three months. If conditions are such that the condenser is
totally blocked in three months, the frequency of cleaning
should be increased. Clean the condenser with a vacuum
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Never use an acid based cleaning solution!
Many food products have an acidic content
which can deteriorate the finish. Be sure to
clean the stainless steel surfaces of ALL food
products. Common items include, tomatoes,
peppers and other vegetables.
Page 15
Delfield
™
®
Maintenance, continued
Gasket Maintenance
Gaskets require regular cleaning to prevent mold and mildew
build up and also to keep the elasticity of the gasket. Gasket
cleaning can be done with the use of warm soapy water.
Avoid full strength cleaning products on gaskets as this can
cause them to become brittle and prevent proper seals. Also,
never use sharp tools or knives to scrape or clean the gasket
which could possibly tear the gasket and rip the bellows.
Gaskets can easily be replaced and do not require the use of
tools or authorized service persons. The gaskets are “Dart”
style and can be pulled out of the grove in the door and new
gaskets can be “pressed” back into place.
Doors/Hinges
Over time and with heavy use doors the hinges may become
loose. If it is noticed that the door is beginning to sag, it
may become necessary to tighten the screws that mount the
hinge brackets to the frame of the unit. If the doors are loose
or sagging this can cause the hinge to pull out of the frame
which may damage both the doors and the door hinges.
In some cases this can require qualified service agents or
maintenance personnel.
If it becomes necessary to adjust a door, follow these
instructions:
1. If the door needs lowering at the handle, use a 5/16”
wrench to loosen the hinge screws and install a spacer
outside of the hinge (see illustration 1). Tighten the
screws.
2. If the door needs to be higher at the handle, use a
5/16” wrench to loosen the hinge screws and install a
spacer inside of the hinge (see illustration 2). Tighten
the screws.
the evaporator housing to the condensate evaporator drain
pan. If water is collected underneath the unit you may want
to check the condensate evaporator drain tube to be sure
it is still located inside the drain pan. The leveling of the
unit is important as the units are designed to drain properly
when on a level surface, if your floor is not level this can
also cause drain problems. Be sure all drain lines are free of
obstructions, typically food product is found blocking drain
lines causing water to back up and overflow the drain pans.
Service Alert
During normal operation the evaporator fan may cycle
and/or pulse independently of the compressor. Consult
the service manual or contact Technical Support at
1-800-733-8829 if you are unsure of the proper function.
Illustration 2:
spacer inside
Drain Maintenance
Each unit has a drain located inside the unit which removes
the condensation from the evaporator coil and evaporates it
at an external condensate evaporator pan. Each drain can
become loose or disconnected from moving or bumping the
drain. If you notice excessive water accumulation on the
inside of the unit be sure the drain tube is connected from
Page 16
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
®
Refrigerator Wiring Diagram - 400 and 4000 Series
LINE VOLTAGE
115V/60Hz/1Ph and 220V/50Hz/1Ph
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
TERMINAL BLOCK L
N
Not used on all models
G
GRN-YEL
BLUE
BROWN
RS ONLY
NDED
PRESSOR
CLOSED
Delfield
™
EVAPORATOR FAN
M
TEMPERATURE
CONTROL
M
ORANGE
COMPRESSOR
M
CONDENSOR FAN
PROPRIETARY
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
MATERIAL
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
SIGNATURE
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES
.X ±
.XX ±
.XXX ±
ANG. ±
.1
.03
.010
1
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
THIRD ANGLE
PROJECTION
DRAWN:
DATE
2/28/2012
DESCRIPTION
LABEL,
MFG:
PURCH:
SIZE
C
QA:
DO NOT SCALE DRAWING
Page 17
SCALE
LOC
Delfield
™
®
REVISIONS
REV
1
Freezer Wiring Diagram - 400 Series
DESCRIPTION
DATE
RELEASE TO PRODUCTION
2/28/2012
LINE VOLTAGE
115V/60Hz/1Ph and 220V/50Hz/1Ph
SEE NAMEPLATE FOR MAXIMUM
FUSE SIZE
OTES:
USE COPPER CONDUCTORS ONLY
THIS UNIT MUST BE GROUNDED
UNIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
L
N
G
BROWN
BLUE
GRN-YEL
TERMINAL BLOCK
Not used on all models
TEMPERATURE
CONTROL
L
N
3
5
EVAPORATOR FAN
F
FAN RELAY
M
VIOLET
6
DEFROST
HEATER
HI-LIMIT
H
YELLOW
4
HEATER RELAY
C
COMPRESSOR
RELAY
M
ORANGE
1
COMPRESSOR
1.1,2,3 2.1,2,3 3.1,2,3
CONDENSOR FAN
CABINET AIR
SENSOR
EVAP COIL
SENSOR
LED DISPLAY
(IF USED)
M
PROPRIETARY
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES
.X ±
.XX ±
.XXX ±
ANG. ±
.1
.03
.010
1
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
THIRD ANGLE
PROJECTION
Page 18
SIGNATURE
UNLESS OTHERWISE SPECIFIED
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
DRAWN:
DATE
2/28/2012
MFG:
PURCH:
ReachDESCRIPTION
LABEL,WIRING,400 FRZ,230V/50HZ,CE
SIZE
C
QA:
DO NOT SCALE DRAWING
SCALE
DWG. NO.
9294484
SHEET
1 OF
1
Delfield
™
®
Freezer Wiring Diagram - 4100 Series
L1
115V/60Hz/1Ø
G
Black
N
NEMA 5-15P
Supply Cord &
Plug Furnished
White
Mullion Heater
(4148 Only)
Defrost Limit
Defrost Heater
Evaporator Fan
Defrost
Timer
Temperature
Control
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Condensing
Unit
Page 19
Delfield
™
®
Replacement Parts List
402/406 Series Refrigerator, 115V/60Hz/1Ph
402/406 Series Refrigerator, 230V/50Hz/1Ph
Part #
Description
0074057
Capillary tube, .044” id x 144”
3234025
Caster, 3”, brake
3234024
Caster, 3”, no brake
3234160
Caster, 5”
3234161
Caster, 5” with brake
3526997Compressor
3516446
Compressor relay
2194787
Compressor start capacitor
158-ATA-0050 Condensate coil, hot gas
149-AWM-0040 Condensate pan
3516275
Condenser coil
3516172
Condenser fan blade
3516173
Condenser fan guard
2162691
Condenser fan motor
000-B3I-003E Door assembly, solid, hinged right
1702623
Door gasket
3516116
Evaporator coil
3516172
Evaporator fan blade
3516173
Evaporator fan guard
2162691
Evaporator motor
3516321
Filter drier
3237569
Hinge bracket, bottom left
3237563
Hinge bracket, bottom right
3237568
Hinge bracket, top left
3237562
Hinge bracket, top right
3237516
Hinge cartridge (spring loaded)
3234225A
Pivot cap, nylon, 1” square
117-CB5-0030 Pump bracket
3978271Shelf
3235014
shelf clip
MCP00207
Shoulder screw
000-CB1-0030 Speed rail assembly
2194759KT
Temperature control
(includes control, knob and dial plate)
2194761
Temperature control knob only
3516135
Thermometer, hanging
120-C85-0030 Whipped cream box
Part #
Description
120-CB6-0030 Bracket, coffee machine
9321079Bumper
127-C15-0105 Bumper bracket
0074057
Capillary tube, .044” id x 144”
3234025
Caster, 3”, brake
3234024
Caster, 3”, no brake
3235515
Caster 4”
3235516
Caster 4”, with brake
3526994
Compressor (220-240V)
3516451
Compressor start capacitor
3516452
Compressor start relay
158-ATA-0050 Condensate coil, hot gas
149-AWM-0040 Condensate pan
3516275
Condenser coil
3516172
Condenser fan blade
3516173
Condenser fan guard
2162692
Condenser motor (230V)
000-B3I-003E Door assembly, solid, hinged right
000-B3I-003H Door assembly, solid, hinged right ,
CP3 model only
1702623
Door gasket
3516172
Evaporator fan blade
3516173
Evaporator fan guard
2162692
Evaporator motor (230V)
3516116
Evaporator coil
3516321
Filter drier
3237569
Hinge bracket, bottom left
3237563
Hinge bracket, bottom right
3237568
Hinge bracket, top left
3237562
Hinge bracket, top right
3237516
Hinge cartridge (spring loaded)
3234225A
Pivot cap, nylon, 1” square
3978271Shelf
3235014
shelf clip
MCP00207
Shoulder screw
000-CB1-0030 Speed rail assembly
2194759KT
Temperature control
(includes control, knob and dial plate)
2194761
Temperature control knob only
3516135
Thermometer, hanging
3516587
Thermometer, solar digital
Page 20
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Delfield
™
®
Replacement Parts List, continued
4048 Series Refrigerator, 115V/60Hz/1Ph
Part #
Description
3234025
3” Caster, brake
3234024
3” Caster, no brake
3234160
5” Caster, no brake
3234161
5” Caster, brake
3234791
6” Leg
000-B3I-0035 24” Door, solid, left hand
000-B3I-0034 24” Door, solid, right hand
0074057
Capillary tube (.044 id x 144”)
3526997Compressor
3516446
Compressor relay
2194787
Compressor start capacitor
158-ATA-0050 Condensate coil, hot gas
149-AWM-0040 Condensate pan
3516275
Condenser coil
3516172
Condenser fan blade, clear lexan
3516173
Condenser fan guard
2162691
Condenser fan motor
1702622
Door gasket
3516116
Evaporator coil
3516172
Evaporator fan blade, clear lexan
3516173
Evaporator fan guard
2162691
Evaporator fan motor
3516321
Filter drier
0420067
Hinge kit (left or right hinged)
3978272Shelf
2194759KT
Temp control (control, knob and
dial plate)
403/407 Series Freezer, 115V/60Hz/1Ph
Part #
Description
3234025
3” Caster, brake
3234024
3” Caster, no brake
3234160
5” Caster, no brake
3234161
5” Caster, brake
3234791
6” Leg
000-B3I-0031 27” Door, solid, left hand
000-B3I-0030 27” Door, solid, right hand
0074058
Capillary tube (.036 id x 168”)
3526996Compressor
3516446
Compressor relay
2194787
Compressor start capacitor
158-ATA-0050 Condensate coil, hot gas
149-AWM-0040 Condensate pan
3516275
Condenser coil
3516172
Condenser fan blade, clear lexan
3516173
Condenser fan guard
2162715
Condenser fan motor
2194817KT-S
Control, Frz, Danfoss, ETC1H-3, 115V
2194774
Defrost heater
1702623
Door gasket
3516418
Evaporator Coil
3516172
Evaporator fan blade, clear lexan
3516173
Evaporator fan guard
2162691
Evaporator fan motor
3516321
Filter Drier
3978055
Heater guard, 18”
0420067
Hinge kit (left or right hinged)
3978271Shelf
3235014
Shelf clip
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 21
Delfield
™
®
Replacement Parts List, continued
403/407 Series Freezer, 230V/50Hz/1Ph
Part #
Description
3234025
3” Caster, brake
3234024
3” Caster, no brake
3234160
5” Caster, no brake
3234161
5” Caster, brake
3234791
6” Leg
000-B3I-0031 27” Door, solid, left hand
000-B3I-0030 27” Door, solid, right hand
0074058
Capillary tube (.036 id x 168”)
3527013
Compressor, 220-240V, R-404a
2194820
Compressor relay
2194821
Compressor start capacitor
158-ATA-0050 Condensate coil, hot gas
149-AWM-0040 Condensate pan
3516275
Condenser coil
3516172
Condenser fan blade, clear lexan
3516173
Condenser fan guard
2162692
Condenser fan motor. 230V
2194964-6KT-S Control, Frz, 230V, 407, Kit
2194774
Defrost heater
1702623
Door gasket
3516418
Evaporator Coil
3516172
Evaporator fan blade, clear lexan
3516173
Evaporator fan guard
2162692
Evaporator fan motor, 230V
3516321
Filter Drier
3978055
Heater guard, 18”
0420067
Hinge kit (left or right hinged)
3978271Shelf
3235014
Shelf clip
Page 22
4148 Series Freezer, 115V/60Hz/1Ph
Part #
Description
3234025
3” Caster, brake
3234024
3” Caster, no brake
3234160
5” Caster, no brake
3234161
5” Caster, brake
000-B3I-0035 24” Door, left hand
000-B3I-0034 24” Door, right hand
3234791
6” Leg
180-CJL-0030 Capillary tube (.036 id x 120”)
3527000Compressor
158-ATA-0050 Condensate coil, hot gas
149-AWM-0040 Condensate pan
3516276
Condenser coil
3516172
Condenser fan blade, clear lexan
2162715
Condenser fan motor
2194774
Defrost heater
3516156
Defrost timer
1702622
Door gasket
3516418
Evaporator coil
3517356
Evaporator fan blade, black
3516173
Evaporator fan guard
2162691
Evaporator fan motor
3516321
Filter drier
3978055
Heater guard, 18”
0420067
Hinge kit (left or right hinged)
3978272Shelf
3517400
Thermostat, Mechanical, Freezer
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Delfield
™
®
Standard Labor Guidelines To Repair or Replace Parts on Delfield Equipment
Improper servicing or service not performed by an authorized service agent could result in an explosion or damage.
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•A maximum of 1-hour is allowed to diagnose a defective component.
•A maximum of 1-hour is allowed for retrieval of parts not in stock.
•A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
•Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
• Compressor Start Components and Overload Protector
• Door Hinges, Locks, and Gaskets
• Evaporator/Condenser Fan Motor and Blade
• Thermostat
LABOR OF 2 HOURS TO REPLACE:
• Defrost Element
• Locate/Repair Leak
LABOR OF 3 HOURS TO REPLACE:
• Capillary Tube
• Condenser or Evaporator Coil
LABOR OF 4 HOURS TO REPLACE
•Compressor, this includes recovery of refrigerant and leak check.
$55.00U.S. maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor
fittings, solder, brazing rod, nitrogen, or similar fees.)
REFRIGERANTS
•R404A A maximum of $15.00U.S./lb. or $1.00U.S./oz. will be reimbursed.
For factory assistance, call
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
Page 23
Delfield
™
®
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous customer
service reps by having your model number and serial number available at the time
of your call (800) 733-8829.
Model:________________________ S/N: _______________________
Installation Date:________________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com
Register your Delfield warranty
online. Go to www.delfield.com
under the service tab to complete.
Delfield
™
®
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2013 The Delfield Company. All rights reserved. Printed in the U.S.A.
DMMcD400_4000 04/13
9294260
Delfield
™
®
ATTENTION Page 2
•
•
•
•
•
Delfield
™
®
Page 3
Delfield
™
®
Certifications Réglementaires
Les modèles sont certifiés par:
National Sanitation Foundation (NSF)
Underwriters Laboratories (UL)
Underwriters Laboratories of Canada (ULC)
Page 4
Delfield
™
®
V/Hz/Ph
AMPS
402-MD1,
402-DHL-MD1
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
80 kg
(176 lb)
NEMA
5-15P
402-MD2,
402-DHL-MD2
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
80 kg
(176 lb)
NEMA
5-15P
402-MD3,
402-DHL-MD3
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198g
(7 o z)
115/60/1
4,0
80 kg
(176 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
230/50/1
1,8
80 kg
(176 lb)
S/O
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198g
(7 oz)
115/60/1
4,0
80 kg
(176 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
230/50/1
1,8
80 kg
(176 lb)
S/O
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
184 g
(6,5 oz)
115/60/1
5,8
83 kg
(184 lb)
NEMA
5-15P
403-MD2,
403-DHL-MD2
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
184 g
(6,5 oz)
115/60/1
5,8
83 kg
(184 lb)
NEMA
5-15P
403-MD3,
403-DHL-MD3
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
184 g
(6,5 oz)
115/60/1
5,8
83 kg
(184 lb)
NEMA
5-15P
406-MD1,
406-DHL-MD1
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
406-MD2,
406-DHL-MD2
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
406-MD2-CP2,
406-DHL-MD2-CP2
1
0,21 m2
(2,3 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
80 kg
(176 lb)
NEMA
5-15P
406-MD2-CP3,
406-DHL-MD2-CP3
1
0,21 m2
(2,3 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
230/50/1
1,8
80 kg
(176 lb)
10 A
Type I
1
2.3ft2
(.21m2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
1
2.3ft2
(.21m2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
402-MD4
402-MD5,
402-DHL-MD5
402-MD6
403-MD1
406-MD2-CP5
406-MD2-CP6
406-MD3,
406-DHL-MD3
406-MD4
406-MD5,
406-DHL-MD5
Page 5
Delfield
™
®
Spécifications (suite)
Modèle
406-MD6
406-MD7
406-MD8
406-MD9
407-MD1
407-MD2
407-MD3,
407-DHL-MD3
ST4048-MD1
ST4048-MD2
ST4048-MD3
ST4048-MD4
ST4148-MD1
ST4148-MD2
Page 6
V/Hz/Ph
AMPS
Type de
fiche
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
78 kg
(172 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
230/50/1
1,8
78 kg
(172 lb)
S/O
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
230/50/1
1,8
78 kg
(172 lb)
S/O
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
198 g
(7 oz)
230/50/1
1,8
78 kg
(172 lb)
S/O
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
184 g
(6,5 oz)
115/60/1
5,8
80 kg
(176 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
184 g
(6,5 oz)
115/60/1
5,8
80 kg
(176 lb)
NEMA
5-15P
2
0,43 m2
(4,6 pi2)
0,16 m3
(5,7 pi3)
1/5
184g
(6,5 o z)
230/50/1
2,1
80 kg
(176 lb)
10A
Type I
4
0,74 m2
(8,0 pi2)
0,31 m3
(10,8 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
106 kg
(234 lb)
NEMA
5-15P
4
0,74 m2
(8,0 pi2)
0,31 m3
(10,8 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
106 kg
(234 lb)
NEMA
5-15P
4
0,74 m2
(8,0 pi2)
0,31 m3
(10,8 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
106 kg
(234 lb)
NEMA
5-15P
4
0,74 m2
(8,0 pi2)
0,31 m3
(10,8 pi3)
1/5
198 g
(7 oz)
115/60/1
4,0
106 kg
(234 lb)
NEMA
5-15P
4
0,74 m2
(8,0 pi2)
0,31 m3
(10,8 pi3)
1/3
198 g
(7 oz)
115/60/1
5,6
110 kg
(242 lb)
NEMA
5-15P
4
0,74 m2
(8,0 pi2)
0,31 m3
(10,8 pi3)
1/3
198 g
(7 oz)
115/60/1
5,6
110 kg
(242 lb)
NEMA
5-15P
Delfield
™
®
Installation
Emplacement
REMARQUE
Plomberie
ATTENTION
Stabilisation
REMARQUE
ATTENTION
Page 7
Delfield
™
®
Plate caster installation, 400 & 4000 Series.
MISE EN GARDE
6,0 cm
(2,38 po)
9,0 cm
(3,40 po)
4,0 cm
(1,75 po)
7,0 cm
(2,82 po)
2,0 cm
(0,94 po)
5,0 cm
(2,14 po)
REMARQUE :
REMARQUE :
REMARQUE :
Patte de 15,2 cm (6 po) – 3234569
Roulette de 7,6 cm (3 po) – 3234024
Roulette de 12,7 cm (5 po) – 3234161
Patte de 15,2 cm (6 po) – 3234791
Page 8
Delfield
™
®
X
400
X
4000
X
X
4000
X
X
X
X
X
X
X
X
Page 9
Delfield
™
®
CONCERNANT
LES
Page 10
Delfield
™
®
REMARQUE
Page 11
Delfield
™
Page 12
®
Delfield
™
®
Page 13
Delfield
™
Page 14
®
Delfield
™
®
ATTENTION
ATTENTION
IL NE FAUT JAMAIS UTILISER DES TAMPONS
EN ACIER, DES BROSSES MÉTALLIQUES OU DES
GRATTOIRS.
ATTENTION
Page 15
Delfield
™
®
Page 16
Alerte d’intervention
®
VERT/JAUNE TERRE
BLEU NEUTRE
TENSION D'ALIMENTATION
115 V / 60 Hz / 1 Ph et 220 V / 50 Hz / 1 ph
CONSULTER LA CAPACITÉ MAXIMALE
DU FUSIBLE SUR LA PLAQUE D’IDENTIFICATION
MARRON PHASE
TORS ONLY
OUNDED
MPRESSOR
S CLOSED
Delfield
™
VENTILATEUR DE L’ÉVAPORATEUR
M
RÉGULATION
DE TEMPÉRATURE
M
ORANGE
COMPRESSEUR
M
VENTILATEUR DU CONDENSEUR
PROPRIETARY
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES
.X ±
.XX ±
.XXX ±
ANG. ±
.1
.03
.010
1
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
888-436-5442
or 989-773-7981
Fax 888-779-2040
www.delfield.com
SIGNATURE
UNLESS OTHERWISE SPECIFIED
DRAWN:
DATE
2/28/2012
DESCRIPTION
MFG:
PURCH:
SIZE
C
QA:
DO NOT SCALE DRAWING
Page 17
SCALE
Delfield
™
®
REVISIONS
REV
1
DESCRIPTION
DATE
RELEASE TO PRODUCTION
2/28/2012
VERT/JAUNE TERRE
MARRON PHASE
BORNIER
ES:
SE COPPER CONDUCTORS ONLY
IS UNIT MUST BE GROUNDED
NIT SHOWN WITH COMPRESSOR
RUNNING AND DOORS CLOSED
BLEU NEUTRE
TENSION D'ALIMENTATION
115 V / 60 Hz / 1 Ph et 220 V / 50 Hz / 1 ph
CONSULTER LA CAPACITÉ MAXIMALE
DU FUSIBLE SUR LA PLAQUE D’IDENTIFICATION
RÉGULATION
DE TEMPÉRATURE
L
3
CIRCUIT DE
COMMANDE
N
5
F
RELAIS DE
VENTILATEUR
M
VIOLET
6
LIMITE HAUTE
H
RELAIS DE
CHAUFFAGE
JAUNE
4
C
M
ORANGE
1
COMPRESSEUR
M
DÉTECTEUR D’AIR
DE L’APPAREIL
DÉTECTEUR DE
SERPENTIN D'ÉVAPORATEUR
AFFICHAGE LED
(SI UTILISÉ)
RELAIS DU
COMPRESSEUR
1.1,2,3 2.1,2,3 3.1,2,3
VENTILATEUR DU CONDENSEUR
PROPRIETARY
The contents of this document are
PROPRIETARY TO THE DELFIELD COMPANY
and are not to be disclosed to others
or used for purposes other than
intended without the written approval
of The Delfield Company.
MATERIAL
SIGNATURE
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES
.X ±
.XX ±
.XXX ±
ANG. ±
.1
.03
.010
1
ALL PARTS TO BE DEBURRED AND EDGES
BROKEN .010 MAXIMUM.
THIRD ANGLE
PROJECTION
Page 18
CHAUFFAGE
DE DÉGIVRAGE
DRAWN:
DATE
2/28/2012
MFG:
PURCH:
Reach-in Divi
DESCRIPTION
LABEL,WIRING,400 FRZ,230V/50HZ,CE
SIZE
C
QA:
DO NOT SCALE DRAWING
SCALE
DWG. NO.
9294484
SHEET
1 OF
1
Delfield
™
®
TERRE
NEUTRE
115 V / 60 Hz / 1 Ø
NEMA 5-15P
Cordon et fiche finis
Noir
Blanc
CHAUFFAGE DE
DÉGIVRAGE
MINUTERIE DE
DÉGIVRAGE
CONDENSEUR
RÉGULATION DE
TEMPÉRATURE
Page 19
Delfield
™
®
Page 20
Delfield
™
®
Page 21
Delfield
™
®
Page 22
Delfield
™
®
Page 23
Delfield
™
®
Covington, TN
Mt. Pleasant, MI
Delfield
™
®
DMMcD400_4000 04/13
9294260
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages

Only pages of the document in English were displayed