User manual | notice_p1689

X-RAY 2 NEO
LASER PROFESSIONNEL
MANUEL D’UTILISATION
1.
RECOMMANDATIONS GENERALES
 FACE AVANT
1.
2.
3.
Infrarouge
 FACE ARRIERE
1.
Prise alimentation
2.
3.
Interlock
4.
Laser ON-OFF
5.
6.
Carte SD
7.
Ecran LCD
8.
9.
2.
FONCTIONS ET REGLAGES
CH1
Function
Model Select
Value
0-49
PRG mode
50-99
ILD mode
100-149
Audio(Sound Active) mode
150-199
Auto mode
200-255
Manual mode
Manual mode
CH2
Pattern/Folder
Select
0-255
Pattern select,every 3
value one pattern
Manual mode
CH3
Strobing/File
Select
0-5
Laser off
6-10
Laser on, no strobe
11-199
Auto strobe
200-255
Audio strobe
0-125
CH4
(Manual
X move
mode)
CH4
(PRG/ILD
File select
PRG/ILD mode
Play file select
Adjust position by manual
126-185
Move circle from left to right automatically
186-225
Jump circle from right to left automatically
226-245
Auto jumping
246-255
Audio jumping
0-127
Laser off
128-255
Laser on
Laser ON/OFF
mode)
CH5
PRG/ILD mode
Y move
0-125
Adjust position by manual
CH6
Zoom(+/-)
126-185
Move circle from up to down automatically
186-225
Jump circle from down to up automatically
226-245
Auto jumping
246-255
Audio jumping
0-10
No change
11-87
Adjust size by manual
88-150
Zoom +
151-200
Zoom -
201-255
Zoom (+/-) circle
0
CH7
Rolling X
1-128
129-255
0
CH8
Rolling Y
1-128
129-255
0
CH9
CH10
Rolling Center
Drawing
1-128
CH12
X wave
Y wave
Manual rotation
Auto rotation
No change
Manual rotation
Auto rotation
No change
Manual rotation
129-192
Auto clockwise rotation
193-255
Auto counterclockwise rotation
0-10
No change
10-74
Manual drawing
75-104
Auto drawing +
105-144
Auto drawing -
145-184
Auto drawing circle
185-224
End to end drawing circle +
225-255
End to end drawing circle -
0-9
CH11
No change
No wave
10-69
Small wave
70-129
Medium wave
130-189
Big wave
190-255
Biggest wave
0-9
No wave
10-69
Small wave
70-129
Medium wave
130-189
Big wave
190-255
Biggest wave
0-63
CH13
Display Mode
CH14
CH15
Normal display
64-127
Light dot display
128-191
Segment display
192-255
Dot display
0-16
White
17-33
Red
34-50
Green
51-67
Blue
68-84
Yellow
85-101
Purple
RGB Models
102-118
Cyan
Color Select
119-135
White, red, green, blue color section
136-152
Blue, yellow, purple, cyan color section
153-169
W, R, G, B, Y, P, C 7 color section
170-186
White, red, green, blue 4 color flow
187-203
Blue, yellow, purple, cyan 4 color flow
204-220
Blue, yellow, purple, cyan 4 color flow
221-237
color subsection by inflexion
238-255
Sound active color change
Red Dimmer
CH16
Green Dimmer
CH17
Blue Dimmer
FONCTIONNEMENT
DE LA TELECOMMANDE IR
0-255
0-255
0-255
Dimmer laser output power from 100% to 0%
Dimmer laser output power from 100% to 0%
Dimmer laser output power from 100% to 0%
2.
3. DEPANNAGE
1.
4.
5.
7.
X-RAY 2 NEO
PROFESSIONAL LASER
USER GUIDE
Thank you for using our products. For the sake of safety and better operation of this product, please read
this manual carefully before using and operating it.
1.
GENERAL INSTRUCTIONS
a.
UNPACKING
Thank you for purchasing this product. Please read the user guide for safety and operations information
before using the product. They contain important information about the security of the facility and on the
use and maintenance of equipment.
Keep this manual for future reference. In case of sale of equipment to another user, it is important that this
manual is attached to the equipment to the new user has the necessary information to use and can read
the warnings on safety.
It is essential that the user duly follows the safety instructions and warnings mentioned in that user
manual. The dealer won’t be able be responsible for the defaults or any other problems due to the
mishandling from the user and the non-following of the instructions included in that user manual.
This product is suitable for creating perfect laser programs and high-quality laser effects.
This unit is designed to produce decorative effect lighting and is used in light show systems.
This product is a so-called show laser emitting radiation with a wavelength spectrum and producing lasers
for shows. Please refer to the safety instructions specific for lasers.
Before any first use, unpack the set and make sure there was no damage during transport. Check for
missing any part supplied with the laser:
- 1 x X-RAY 2 NEO
- 1 x POWER CABLE
- 1 x USER MANUAL
- 1 x IR REMOTE
b.
-
GENERAL SAFETY INSTRUCTIONS
This fixture must be earthed to in order to comply with the safety regulations and to avoid any electrical
shock.
-
Before using, please be assure that the voltage is appropriate with the information mentioned at the rear
panel of the unit. Ot avoid any shock hazard, do not open or remove the cover.
-
This unit is designed for indoors use. Do not expose the unit to rain or moisture.
-
The working temperature of the unit is from 18 to 30°C. Do not use it at higher temperature.
-
Do not switch on and off many times to avoid reducing the life duration of the fixture.
-
Do not use the unit for more than 4 hours in order not to decrease the life duration of your fixture.
-
Always unplug the unit when we do not use it for a long time or before servicing.
-
Do not place metal objects or spill liquids in/over the unit. If it occurs, please disconnect the unit from the
-
Keep the device away from flammable or hot sources.
-
The fixture should be placed in a ventilated area and fixed at 50 cm at least from the walls.
-
Do not cover the ventilation openings as it may result in overheating.
-
Do not use the unit id dusty environment. Please use soft cloth to remove dust that would be place in the
mains at once.
external lens. Clean the unit regularly.
-
Keep away from children or any non-qualified persons.
-
During the installation of the units, do not let the inexperienced people come around and operate the
device.
-
Make sure that the area below the installation is free from unwanted persons.
-
The installation should be carried out qualified persons only according to the regulations for safety rules.
-
Do not remove the stickers placed on the unit. It is forbidden to make any unauthorized modifications to
the unit due to safety reasons.
-
If some parts are visibly damaged (power cord, lens, plug, casing brackets), please do not use the unit
and contact your dealer
-
The unit does not have user serviceable parts inside. Refer to qualified persons or contact your dealer.
-
Always use parts of same type.
-
Never repair a fuse or bypass the fuse holder.
-
Please use the original packaging for transporting the device.
-
In the event of serious problems, stop using the device contact your dealer. Do not open the cover.
Never look at the light source directly! Do not use the unit effects in the presence of persons
suffering from epilepsy.
DO NOT OVER DRIVE THE SCANNERS. WHEN USING MAX SPEED KEEP THE ANGLE SMALL.
FOR MAX ANGLE DO NOT EXCEED 20KPPS ON THE ILDA SOFTWARE SETTING.
c.
SAFETY INTRUCTIONS FOR LASERS
According to EN/IEC 60825-1 regulations, this laser is classified under 4 class. Direct eye
exposure can be dangerous
DANGER: LASER RADIATION!
UNIT UNDER 4 CLASS
AVOID DIRECT EYE EXPOSURE. LASER RADAITION CAN CAUSE EYE
DAMAGE AND/OR SKIN DAMAGE
AVOID EXPOSTION TO LASER RADIATION
ALL PROTECTIVE MEASURES MUST BE APPLIED FOR MAKING THE
USE OF LASERS SAFE
This product is a so-called show laser emitting radiation with a wavelength spectrum and producing lasers
for shows.
A laser (Light Amplification by Stimulated Emission of Radiation) is a device that emits light trough a
process of optical amplification and produce electromagnetic radiation of different wavelengths due to the
controlled stimulated emissions process.
In addition to the secondary effects due to the operating laser conditions, fire risks or burning hazards, the
most important danger comes from the light source. The damages on eyes depend on the laser
wavelengths specifications, the eye distance and the elements linked to the eye specifications. This
danger is amplifies if the laser beams are focused to tiny spots; that is why the effects on eyes are even
more important while using lasers.
3B class can be dangerous under specific conditions
4 class should be ruled under strict safety warnings.
In accordance with French applicable decree n° 2012-1303 dated from November 26, 2012, the use of
lasers above class 2 is restricted to professional activities (light shows, performing arts…).
Restricted uses can be seen on:
http://www.legifrance.gouv.fr/affichTexte.do?cidTexte=JORFTEXT000026694613&dateTexte=&categorie
Lien=id (French only)
Make sure to check your country's restrictions and law regarding the use of lasers
INSTALLATION OF THE UNIT
The units from 3B class and 4 class, exclusively used in open air, should be installed by experienced and
qualified professionals, trained to the specific risks of lasers and should handle a user manual.
The area reserved for the public should be limited up to 3 meters above the ground and to 2.5 meters
from the public. This zone should be indicated and marked on the ground. In this area, it is not possible to
make “pencil beams” (through the output being a narrow beam which is diffraction-limited) in the direction
of people, whatever the laser class is, except if a determined area has been defined of 4 meters radius
from the public and visibly marked on the ground.
Only laser beams of wavelengths divergence concentrated their power at a large distance are authorized.
OPERATION OF THE UNIT
The use of lasers is out of the reach of people when considering:
- That the unit is situated at 3 meters above the floor at least
- That a safety area is defined within 5 meters radius
- The user takes the responsibility that the units under 3B class or 4 class are mounted by a qualified
technician and experienced to the risks of lasers. This technician must stay around during all the time the
lasers work and he must be able to stop the units in case some technical problems would occur. While the
installation is on, the technician should wear protective glasses.
Please remind the following remarks:
- Laser light is different from any other light source with which you may be familiar. The light from this
product can potentially cause eye injury if not set up and used properly.
- Laser light is thousands of times more concentrated than light from any other kind of light source. This
concentration can cause instant eye injuries, by burning the retina. Even if you cannot feel heat from a
laser beam, it can still injure or blind you or the audience.
- Never look at the laser aperture or laser beams.
- Do not direct the laser beam to people.
- Do not leave the device running without the presence of qualified professionals.
EXPELEC cannot liable for damages caused by incorrect installations and unskilled operation.
2.
SPECIFICATIONS
Voltage : AC100-250V, 50Hz/60Hz
Fuse : 3A/250V
Rated Power : 150W
Angle : +/-30°C
Scanner : 25kpps
DMX channels : 17
Laser :
Green 532 nm / 500 mW
Red 635 nm / 400 mW
Blue : 450 nm / 1600 mW
Working modes : DMX 512 (17 CH), Sound activation, Auto-beam, Auto-animation, Master/Slave, Ilda
mode (PC control/ SD card program)
Graphics & Effects : Beam show and animated graphics show patterns
Interface : 3 pin XLR jack for DMX or Master/Slave linking
SD card : 2GB, built in program and downloading program
ILDA computer interface
Dimensions : 220 x 280 x 160 mm
Weight : 7.5 kg
3.
FEATURES
Animation laser with high optical scanner to create animated graphics, 128 beam show and graphics
show patterns and with the function of unique blanking, frequently flashing, rotating, moving, split, zoom
(+/-), speed and color.
Including 6 working modes as DMX 512, sound active auto-animation, auto-beam, master/slave and PC
control (with DB25 ILDA computer interface) for different applications
The unit has 12 channels to control in DMX mode. The unit has blackout function. The unit will shut off if
no DMX signal.
Compatible ILDA laser show software with ILDA interface. Use electronics switches to conversion full
ILDA signal. The unit will shut off if no ILDA signal.
Design according to performance and security.
Master/Slave mode, DMX 512 mode and PC control mode will shut off laser automatically without trigger
signal.
 FRONT PANEL
1.
Laser aperture
2.
Power indicator : Red LED
3.
IR sensor
 REAR PANEL
1.
Power Jack
2.
Power switch
3.
Laser remote interlock
4.
Laser ON-OFF switch
5.
DMX or linking jack
6.
SD card slot
7.
LCD Display
8.
Function setting with key
9.
Pattern size knob
10. ILDA interface with DB25 jack
11. SFS Control: scanner fail safety control ON/OFF
4.
FUNCTIONS AND SETTINGS
Key Operation:
As in the pictures above:
1). MODE: mode key, press the key to select mode.
2). UP & DOWN: Select the current model's content.(switch file under PRG and ILD mode; seting the color,
adjust the pattern size, change sonic rhythm under audio, …）
3).ENTER: Confirmation key
State of mode and operation:
1). Rrg Mode: playlist mode, play PRG file, the second row of LCD shows current playlist name, press "UP" and
"DOWN" to change the playlist, press "ENTER" to change current folder.
2). ILDA Mode: ILDA play mode, play single ILDA file (extension name is .ILD, case insensitive) repeatedly. The
second row of LCD shows the current playing ILDA file name. Press "UP" and "DOWN" to change ILDA file;
press "ENTER" to change current folder.
3). Audio Mode: play built-in sonic programs, press "UP" and "DOWN" to change sonic rhythm.
4). Auto Mode: play built-in auto programs.
5). Dmx Mode: the first row of LCD shows the current mode, the second row shows
and DMX address and
receiving status of console.
6). Phase Set: can set phase / direction of X and Y separately.
Attention
1. The system just support short file name, file name (include folder name), most 8-bit file name and 3
extension name, file name and extension name formed by letter, number and under line. File name can’t over 8
and no Chinese words, otherwise the system can’t identify it.
2. SD card can’t mix other file, most support 20 folders, every folder can save maximum 255 files and 10 PRG
files.
3. Program table: user can use notepad to edit program list, the extension name is .PRG. Program table formed
by play file name, play speed, play times, ishow identify
code "i"(if use ishow software make ild file), middle
using“i”separate. Edit item, for example: one program formed by File1.ild, File2.ild, File3.ild. File1.ild play
speed is 30K, replay
3 times; file2.ild play speed is 35K, play one time, , and file 2 is made by ishow
software; file3.ild play speed is 30K, play 4 times. Then prg1.prg contents as below:
File1.ild,12,3,0
File2.ild,20,1,1,i
File3.ild,18,4,2
When create one folder, need create the same PRG file under the folder, and put all the files need to play in the
folder into the PRG file. For example, under aurora folder, create aurora.prg file.After adding ILDA file, need
add the file to prg file, so that we can find the file quickly and play the file as per the speed you set.
Manu Setting. The LCD will enter the main manu afterlaser ON for 5 seconds
Note:
1.The underlined words are optional mode/ effects
2.When they are shing, use up and down button to choose effects and use enter to confirm the setting.
3. If you don't press the enter botton after 5 seconds,the system will return to the last mode/effects you
confirmed.
4. ①Press UP/DOWN button to choose PRG FILE,press ENTER button to confirm the file.the default mode is
animation effect mode.
5. ②Press UP/DOWN button to choose Effects,Press ENTER button to confirm.
6. ③Press UP/DOWN button to choose FILE，Press ENTER button to confirm the file. The default effects is
ANIMATION EFFECT mode
7. ④Press UP/DOWN button to choose IILDA program,Press ENTER button to confirm the program
8. ⑤Press UP/DOWN button to choose effect mode,press ENTER button to confirm.
DMX OPERATION
IR REMOTE OPERATION
PC CONTROL OPERATION
This mode allows you to use PC software (for example : Mini ILDA, pangolin, phenix, mamba) to operate. If no
ILDA signal to DB25 jack in ILDA mode, the laser and scanner will close for protection.
NOTE:
1.
DMX console cannot be operated in Master / Slave (AUTO / SOUND ACTIVE mode)
2.
There must be only 1 single master unit in Master / Slave mode
6.
1.
TROUBLESHOOTING
If the power indicator does not lit up and the device does not work, please check the power cable is
properly connected and if the input voltage is compatible with that of the device.
2.
In Stand-alone operation, if the power indicator lights up and sound active indicator does not lit up and
the light beam does not work.
3.
a.
The sound is too low. Increase the volume of music or sound sensitivity.
b.
Check if the device is in slave mode then set up in master mode.
In Master / Slave mode, the slave units does not work
a. Make sure there is only 1 single unit in the master channel and the other units are set as a slave.
b. Make sure you are not using a DMX console
c. Make sure the cables are of good quality and the connections are properly made.
4.
In DMX mode, the beam does not work and the DMX signal is off.
a. Make sure the DMX mode is activated.
b. Make sure the cables are of good quality and the connections are properly made.
5.
In DMX mode, the laser is not controlled by the DMX console, DMX signal indicator flashes. Make sure
the console and the units have the same channel.
6.
If the direction of the beam is not correct, restart the machine.
7.
If the unit does not work properly, turn the unit off then back on.
If the unit meets other operational problems, we recommend that you contact your dealer.
NICOLS is a registered trade mark of EXPELEC SA
74370 Charvonnex/ FRANCE – Tél : +33 (0)4 50 60 80 20/ www.expelec.fr

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project