www.tsicustomerservice.com DFI-550-0 MODEL/ MODELE/ MODELO: Español P.12

Add to My manuals
21 Pages

advertisement

www.tsicustomerservice.com DFI-550-0 MODEL/ MODELE/ MODELO: Español P.12 | Manualzz
MODEL/ MODELE/ MODELO:
DFI-550-0
www.tsicustomerservice.com
Distributed by • Distribuido por • Distribué par • Twin-Star International, Inc; Delray Beach, FL 33445
Made in China • Printed in China • Fabricado en China • Impreso en China • Fabriqué en China • Imprimé en Chine
Warning: This is an unvented, electric appliance.
DO NOT attempt to burn wood or manufactured
firelogs in or on this appliance or grate.
REV-0
1
Avertissement : Il s’agit d’un appareil électrique
non ventilé. NE PAS tenter de faire brûler du bois
ou des bûches fabriquées dans l’appareil ou sur
la grille.
www.tsicustomerservice.com
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury
to persons including the following:
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this
appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the
front of this appliance. WARNING: In order to avoid overheating, do not cover the heater.
3. CAUTION: Never leave the heater operating unattended. Extreme caution is necessary if unsupervised children or invalids are nearby.
4. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
5. Always unplug this appliance when not in use.
6. Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, or if it has been dropped or damaged in
any manner.
7. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid
a hazard.
8. Do not use outdoors.
9. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate this appliance where it may
fall into a bathtub or other water container.
10.Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and
where it will not be tripped over.
PORTANT INSTRUCTIONS
this
appliance,
turn
controls
to tothe
off the
position,
then
remove
from
n using 11.To
electricaldisconnect
appliances, basic
precautions
should
always
be followed
reduce
risk of fire,
electrical
shock,plug
and injury
ersons including the following:
notbefore
insert
orthis
allow
foreign
Read all12.Do
instructions
using
appliance.
outlet.
objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage
the
appliance.
This appliance
is hot
when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving
this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet
possible
(0.9 m) 13.To
from the prevent
front of thisaappliance.
fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where opening
In may
blocked.
WARNING:
order tobecome
avoid overheating,
do not cover the heater.
CAUTION: Whenever the heater is left operating and unattended, extreme caution is necessary if children or invalids are nearby.
14.This
appliance
has
hot and
arcing
sparking
parts
inside.
Docapabilities,
not use itor in
The appliance
is not
to be used by
children
or persons
withor
reduced
physical,
sensory
or mental
lackareas
of
and
or knowledge,
stored. This
stove
should
not be
used asor ainstruction.
drying rack
experience
unless
they have
been given
supervision
inthis
theappliance
area ofwhen
it. not in use.
Always unplug
where gasoline, paint or flammable liquids are used
for clothing. Christmas stockings or decorations should not be hung
Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, or if it has been dropped or
damaged
in any manner.
15.Use
this appliance
only as described in the manual. Any other use not recommended by the manufacturer may cause fire, electric shock
f the supply
cordinjury
is damaged,
it must be replaced by the manufacturer, its service agent or similarly qualified persons in order
or
to persons.
to avoid a hazard.
Do not use
outdoors.
16.This
appliance,
when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with
codes and the National Electrical Code,
may fall intoANSI/NFPA
a bathtub or otherNO.70.
water container.
This heater
not current
intended for
use inC22.2
bathrooms,
laundry areas
and similar
indooror
locations.
Never locate
this appliance
where local
it
isthe
CSA
Canadian
Electrical
Code
for U.S.A.
installations,
follow
Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas
and where
it will not be tripped
over.
17.Connect
to properly
grounded outlets only, See Fig.1.This heater is for use on 120 volts. Do not use a 2 prong adapters. Always plug an extension cord or relocatable power tap (outlet/power strip).
o disconnect
this appliance,
turn controls
the off
position, then remove plug fromuse
outlet.
heaters
directly
into atowall
outlet/receptacle.Never
with
Connect to properly grounded outlets only, See Fig.1. Do not use a 2 prong adapters.
A
B
Fig.1
SAVE THESE INSTRUCTIONS
This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes,
with the current CSA C22.1 Canadian Electrical Code or for U.S.A. installations, follow local codes and the National Electrical
Code, ANSI/NFPA NO.70.
Do not insert
or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or
REV-0
damage the appliance.
2
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where
www.tsicustomerservice.com
GETTING STARTED
1. The serial number is located on the back of the stove, the serial number is necessary for product
warranty registration and customer service.
Back of the Stove
Model Number
HIGH TEMPERATURE, RISK OF FIRE, KEEP ELECTRICAL CORDS, DRAPERY,
FURNISHINGS AND OTHER COMBUSTIBLES AT LEAST 3 FEET(0.9M) FROM
THE FRONT OF THE HEATER AND AWAY FROM THE SIDE AND THE REAR.
CAUTION: RISK OF ELECTRICAL SHOCK
DO NOT OPEN NO USER
SERVICEABLE PARTS INSIDE
MODEL / MODÈLE / MODELO
VOLTS
120V~
DFI-550-0
AMPS/AMPÈRES/AMPERIO
12.5
Twin-Star International, Inc.
www.twinstarhome.com
Made In China
Fabriqué en Chine
Fabricado en China
DFI-550-0-A0
Serial Number
SEE OWNERS MANUAL FOR SERVICE DETAILS
WARNING: DISCONNECT POWER BEFORE CLEANING OR SERVICING
CAUTION:
ELECTRIC FIREPLACE/FOYER
ÉLECTRIQUE/INSERTO PARA CHIMENEA
For Customer Service/
Pour Le Service À La Clientèle/
Servicio De Atención Al Cliente:
www.tsicustomerservice.com
(+1) 800 -318 -9373 English
(+1) 800 -318 -9374 Español
(+1) 800 -318 -9374 Français
HZ
60
VOIR LE MANUEL DU PROPRIÉTAIRE POUR LES DÉTAILS
SUR L’ENTRETIEN ET LA RÉPARATION
AVERTISSEMENT: DÉBRANCHEZ L’APPAREIL AVANT DE NETTOYER OU
EFFECTUER L’ENTRETIEN OU LA RÉPARATION.
AVERTISSEMENT:TEMPÉRATURE ÉLEVÉE,RISQUE DEFEU,GARDEZ LES
CORDONS ÉLECTRIQUES,DRAPERIES,MEUBLES ET AUTRES MATIÈRES COMBUTIBLES À AU MOINS 0.9M(3 PIEDS) DE LA PARTIE FRONTALE DE L’APAREIL DE
CHAUFFAGE ET ÉLOIGNÉS DES CÔTÉS.
220391
Part Name/ Nom de la pièce/
Nombre de la parte:
01 Motor/ Moteur
Blower/
02 Soplador/Ventilateur
panel PCBA/ Panneau de contrôle
03 Control
PCBA/Panel de Control PCBA
04 MAIN PCBA/Principal PCBA
05 Remote/Remoto Télécommande
Part/ Partie/
Parte #
P10Q-S
Y13-S100-P29
Y13-S100-P32
Y13-S100-P15
P104
AVERTISSEMENT:
RISQUE DE CHOC ÉLECTRIQUE NE PAS OUVRIR AUCUN
ENTRETIEN DES PIÈCES INTÉRIEURES PAR L’UTILISATEUR
VERA A DUENOS MAÑUALES PARA LOS DETALLES DEL
SERVICIO
AVISO: DESCONECTE LA ENERGÍA ANTES DE APOYARSE O REPAARA.
CUIDADO:
LA TEMPERATURA,RIESGO DE INCENDIO,GUARDA CORDONESÉCRICOS,
PAÑERÍA,MOOBILIARIO Y OOTROS COMBUSTIBLES POR LO MENOS 3 POES
(0.9M) DEL FRENTE DEL CALENTADOR Y LEIOS DE LA PARTE POSTERIOR.
CUIDADO: EL RIESGO DE CHOQUE ELÉCTRICO,NO ABRA.
SN #: SQLA00000X
Date Code/ Code de Date/ Código Fecha:
2. Go to www.tsicustomerservice.com for product warranty registration. For registration use the MODEL
NUMBER: DFI-550-0. If you are unable to complete registration save your proof of purchase for warranty
purposes.
PRODUCT SPECIFICATIONS
VOLTAGE
AMPS
WATTS (max.)
REV-0
120VAC, 60 Hz
12.5 Amps
1500 Watts
3
www.tsicustomerservice.com
INSTALLATION INSTRUCTIONS
Tools Required for Assembly
Phillips Head Screwdriver
Leg Assembly
1
Align the 2 mounting tabs into the
bracket.
REV-0
2
3
Slide the legs outward to lock in
place. When locked in position
the screw hole from step 3 will be
aligned.
Fasten the legs to the base using
the included screws,1 per leg
4
www.tsicustomerservice.com
INSTALLATION INSTRUCTIONS
Mounting The Handle
Insert the handle into the front hole in the door, insert the screw into the interior hole and tighten.
CARE AND MAINTENANCE
Clearance To Combustibles
Keep electrical cords, drapery, furniture and other combustibles at least 3 ft (0.9 m) from the front of the heater and away from the sides.
Cleaning Trim
Clean the metal trim using a soft cloth, slightly dampened with a citrus oil-based product and buff with a soft, clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Purchase citrus oil-based products at a hardware store.
REV-0
5
www.tsicustomerservice.com
OPERATION INSTRUCTIONS
Indicator
Control Panel Location
When a function is changed from the control panel or remote there will be a corresponding indicator. The
indicator shows the function changed and the level selected. When the function is turned off, the
corresponding indicator will flash several times then fade off.
Note: please operate remote transmitter at a slow Measured pace. Press the remote control buttons
With an even motion and gentle pressure. Repeatedly Pressing buttons in rapid succession may cause the
Transmitter to malfunction.
REV-0
6
www.tsicustomerservice.com
OPERATION INSTRUCTIONS
Function
Icon
Description
POWER
Use the power button to turn on or off the stove from the
remote or control panel.
FLAME
To adjust the flame brightness press the FLAME button. The current flame brightness setting will be flashing on
the indicator, use the UP and DOWN arrow to adjust the
brightness.
There are 5 brightness settings, 5 is brightest and 1 is
dimmest.
HEATER
To turn on the heater press the HEATER button. Once
pressed the heater will turn on, the indicator will also be
flashing the current thermostat setting level. Use the UP and
DOWN arrows to set the desired thermostat level.
The thermostat setting range is 60°F - 82°F or 16°C - 28°C or
always ON.
NOTE: To change between °F and °C press and hold the
HEATER button on the control panel for 5 seconds.
TIMER
To set the sleep timer press the TIMER button. Once pressed
the indicator will flash the current timer setting length, use
the UP and DOWN buttons to adjust the timer length.
Timer settings are 30 minutes, 1 Hour, 2H, 3H, 4H, 5H, 6H,
7H, 8H and 9H.
UP AND DOWN
REV-0
Press the corresponding button for the feature to be changed,
FLAME, HEATER, or TIMER then use UP and DOWN to
select the desired setting.
7
www.tsicustomerservice.com
Root Cause
Corrective Action
1. No power
1a. Power cord was not plugged into
the outlet.
1b. Circuit board failure
1a. Check that unit is plugged directly into a standard 120 volt outlet.
1b. Contact Customer Service for a replacement main PCBA.
2. Stove does not
turn on manually.
2a.
2b.
2c.
2d.
2a.
2b.
2c.
2d.
3.Stove does not
turn on with remote.
3a. Improper operation
3b. Remote control not working
4. Flames are not
moving
4a. Defective Flame Generator Drive 4a. Contact customer service for a replacement Flame Generator Drive
Motor
Motor.
4b. Unplug the stove and remove the back panel and check to see if
4b. Flame Generator/Spinner
“Flame Generator/Spinner” is correctly mounted to the Flame
detached from the Flame
Generator Drive Motor
Generator Drive Motor.
5. Flames are not
visible
5. Burnt out LED board
5. Contact customer service for a replacement blue flame PCBA or red
flame PCBA.
6. Flames are not bright
6. Normal operation
6. Press the FLAME button then press the UP arrow until the flame
setting is on 5.
7. Heater is not
turning off
7. Defective Main PCBA
7.
8. Heater is not
turning on
8a. Improper operation
8b. Defective heater blower motor
8c. The HEATER function is locked.
8a. Manually press main power button on front of unit.
8b. Replace heater blower motor.
8c. Hold the POWER button up to 10 seconds to activate the heater
function.
9. Not producing
enough heat
9a. power strip/surge protector/
extension cord being used
9b. Location of unit
9a. Plug unit directly into the wall.
9b. Make sure unit is located on an interior wall or away from drafty
doors or windows.
10.Unit blows cool or
cold air
10. Defective heater blower assembly. 10. Contact customer service to replace the heater blower assembly.
11.Noise with
heater on
11a.Dirty heater blower motor
11b.Defective heater blower motor
11a.Gently vacuum heater blower vents.
11b.Replace heater blower motor
12.Noise with flames
on and heater off
12a.Defective flame generator
drive motor.
12b.Dented back panel
12c.Warped Flame Generator/
Spinner shaft
12a.Contact customer service to replace the flame generator drive motor.
12b.Contact customer service
12c.Contact customer service
13.Power cord gets
warm
13. Normal operation
13.
14.Is it safe to place
unit on carpet?
14. Product inquiry
14. It is safe to place unit on carpet but make sure any flammable
items are at least 3 feet (0.9 m) away from front and sides of the unit. 15.How many square
feet will my unit
warm up?
15. Product inquiry
15. Provides supplemental heat up to 1000 square feet
REV-0
No incoming power from the
electrical wall socket or switches.
Improper operation.
Defective button
Control panel circuit board
failure
Check circuit breakers and move unit to another outlet.
Manually press main power button from front of unit.
Contact customer service to replace the control panel PCBA.
Contact customer service to replace the control panel PCBA.
3a. Point directly at center of the unit.
3b. Install new battery into remote control or Replace remote control if
necessary .
Contact Customer Service for a replacement main PCBA.
Check your heater cord and plug connections. Faulty wall outlet
connections or loose plugs can cause the outlet or plug to overheat.
Be sure the plug fits tight in the outlet. Heaters draw more current
than small appliances, overheating of the outlet may occur even if
it has not occurred with the use of other appliances. During use
check frequently to determine if your plug outlet or faceplate
is HOT! If so, discontinue use of the heater and have a qualified
electrician check and/or replace the faulty outlet(s).
8
www.tsicustomerservice.com
Part Name
Blue Flame PCBA
Red Flame PCBA
Flame Generator Drive Motor
Flame Generator/Spinner
Emberbed with Log
Legs
Heater/Blower Assembly
Main PCBA
Control panel PCBA
Door Pull
Remote control
Note, the scale and size of your parts may be different depending on your exact model
7
8
9
10
1
2
3
4
11
5
6
REV-0
9
www.tsicustomerservice.com
FCC/IC INFORMATION
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Modifications not approved by the party responsible for compliance could void user’s authority to operate the
equipment.
This Class B digital apparatus complies with Canadian ICES-003.
BATTERY REPLACEMENT
NOTE: Do not mix old and new batteries.
Do not mix alkaine, standard (carbon zinc), or rechargable (nicad, nimh, etc.) batteries.
Fig.7
REV-0
10
www.tsicustomerservice.com
1-YEAR LIMITED WARRANTY
The manufacturer warrants that your new Electric Stove is free from manufacturing and material defects for a period of one
year from date of puchase, subject to the following conditions and limitations.
1. Install and operate this appliance in accordance with the installation and operating instructions furnished with the
product at all times. Any unauthorized repair, alteration, willful abuse, accident, or misuse of the product shall nullify
this warranty.
2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through
an authorized supplier of the product.
3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship,
provided that such part(s) have been subjected to normal conditions of use and service, after said defect is confirmed
by the manufacturer’s inspection.
4. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding
the wholesale price of the defective part(s).
5. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s),
repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the manufacturer assume
responsibility for same.
6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or
damage arising out of the use, or inability to use the product,except as provided by law.
7. All other warranties – expressed or implied –with respect to the product, its components and accessories, or any
obligations/liabilities on the part of the manufacturer are hereby expressly excluded.
8. The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with
respect to the sale of the product.
9. The warranties as outlined within this document do not apply to non accessories used in conjunction with the
installation of this product.
10.This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
This warranty is void if:
a. The stove is subjected to prolonged periods of dampness or condensation.
b. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
c. You do not have the original receipt of purchase.
CUSTOMER SERVICE
www.tsicustomerservice.com
For Customer Service Call 1-800-318-9373
IMPORTANT:
Before contacting Customer Service please have this information available:
• Serial Number
• Model Number
• Sales Receipt or Proof of Purchase
Questions? Our experts are standing by assist you at our help line, we can help you with assembly,
and, if necessary replace damaged/missing parts. Assistance is available 7 days a week/24 hours a day/
365 days per year.
REV-0
11
www.tsicustomerservice.com
INSTRUCCIONES IMPORTANTES
PORTANT INSTRUCTIONS
using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury
sons including the following:
ead all instructions before using this appliance.
his appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving
his appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet
0.9 m) from the front of this appliance.
he appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of
xperience and knowledge, unless they have been given supervision or instruction.
15.Utilice este aparato únicamente como se describe en el manual. Cualquier otro uso no recomendado por el fabricante podría causar any
incendio,
descarga
o lesiones
a personas.
o not operate
heater with a damaged
cord oreléctrica
plug or after the
appliance malfunctions,
or if it has been dropped or
lways unplug this appliance when not in use.
amaged in any manner.
the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order
o avoid a hazard.
may fall into a bathtub or other water container.
o not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas
nd where it will not be tripped over.
onnect to properly grounded outlets only, See Fig.1. Do not use a 2 prong adapters.
A
B
Fig.1
GUARDE ESTAS INSTRUCCIONES
his appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes,
with the current CSA C22.1 Canadian Electrical Code or for U.S.A. installations, follow local codes and the National Electrical
REV-0
ode, ANSI/NFPA NO.70.
o not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or
amage the appliance.
o prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where
12
www.tsicustomerservice.com
HIGH TEMPERATURE, RISK OF FIRE, KEEP ELECTRICAL CORDS, DRAPERY,
FURNISHINGS AND OTHER COMBUSTIBLES AT LEAST 3 FEET(0.9M) FROM
THE FRONT OF THE HEATER AND AWAY FROM THE SIDE AND THE REAR.
CAUTION: RISK OF ELECTRICAL SHOCK
DO NOT OPEN NO USER
SERVICEABLE PARTS INSIDE
MODEL / MODÈLE / MODELO
VOLTS
120V~
DFI-550-0
AMPS/AMPÈRES/AMPERIO
12.5
Twin-Star International, Inc.
www.twinstarhome.com
Made In China
Fabriqué en Chine
Fabricado en China
SEE OWNERS MANUAL FOR SERVICE DETAILS
WARNING: DISCONNECT POWER BEFORE CLEANING OR SERVICING
CAUTION:
ELECTRIC FIREPLACE/FOYER
ÉLECTRIQUE/INSERTO PARA CHIMENEA
HZ
60
VOIR LE MANUEL DU PROPRIÉTAIRE POUR LES DÉTAILS
SUR L’ENTRETIEN ET LA RÉPARATION
AVERTISSEMENT: DÉBRANCHEZ L’APPAREIL AVANT DE NETTOYER OU
EFFECTUER L’ENTRETIEN OU LA RÉPARATION.
AVERTISSEMENT:TEMPÉRATURE ÉLEVÉE,RISQUE DEFEU,GARDEZ LES
CORDONS ÉLECTRIQUES,DRAPERIES,MEUBLES ET AUTRES MATIÈRES COMBUTIBLES À AU MOINS 0.9M(3 PIEDS) DE LA PARTIE FRONTALE DE L’APAREIL DE
CHAUFFAGE ET ÉLOIGNÉS DES CÔTÉS.
220391
Part Name/ Nom de la pièce/
Nombre de la parte:
01 Motor/ Moteur
Blower/
02 Soplador/Ventilateur
Control panel PCBA/ Panneau de contrôle
03 PCBA/Panel
de Control PCBA
04 MAIN PCBA/Principal PCBA
05 Remote/Remoto Télécommande
Part/ Partie/
Parte #
P10Q-S
Y13-S100-P29
Y13-S100-P32
Y13-S100-P15
P104
AVERTISSEMENT:
RISQUE DE CHOC ÉLECTRIQUE NE PAS OUVRIR AUCUN
ENTRETIEN DES PIÈCES INTÉRIEURES PAR L’UTILISATEUR
VERA A DUENOS MAÑUALES PARA LOS DETALLES DEL
SERVICIO
AVISO: DESCONECTE LA ENERGÍA ANTES DE APOYARSE O REPAARA.
CUIDADO:
LA TEMPERATURA,RIESGO DE INCENDIO,GUARDA CORDONESÉCRICOS,
PAÑERÍA,MOOBILIARIO Y OOTROS COMBUSTIBLES POR LO MENOS 3 POES
(0.9M) DEL FRENTE DEL CALENTADOR Y LEIOS DE LA PARTE POSTERIOR.
CUIDADO: EL RIESGO DE CHOQUE ELÉCTRICO,NO ABRA.
ESPECIFICACIONES DEL PRODUCTO
VOLTAJE
120VAC, 60 Hz
AMPERAJE
12.5 Amps
POTENCIA EN VATIOS(max) 1500 Watts
REV-0
13
www.tsicustomerservice.com
1
REV-0
2
3
14
www.tsicustomerservice.com
INSTRUCCIONES DE INSTALACIÓN
Montaje del mango
REV-0
15
www.tsicustomerservice.com
INSTRUCCIONES DE OPERACIÓN
16
www.tsicustomerservice.com
INSTRUCCIONES DE OPERACIÓN
FUNCIÓN
ICONO
DESCRIPCIÓN
LLAMA
CALENTADOR
TIMER
ARRIBA Y ABAJO
REV-0
17
www.tsicustomerservice.com
SOLUCIÓN DE PROBLEMAS
Problema
Causa
2. Estufa no se
enciende de forma
manual.
9. No produce sufi
ciente calor
REV-0
18
www.tsicustomerservice.com
VISTA DESPLEGADA
Pieza
1
2
3
4
5
6
7
8
9
10
11
7
8
9
10
1
2
3
4
11
5
6
REV-0
19
www.tsicustomerservice.com
REV-0
20
www.tsicustomerservice.com
SERVICIO AL CLIENTE
www.tsicustomerservice.com
Por Call 1-800-318-9374 Servicio al Cliente
REV-0
21
www.tsicustomerservice.com

advertisement

Related manuals

advertisement

Languages

Only pages of the document in English were displayed