Transmitter Program Guide

MODEL: APS02BT2
TRANSMITTER PROGRAMMING GUIDE
The transmitters included in the security system kit are pre-programmed at
the factory, with button # 1 assigned to the Arm, Lock / Disarm, Unlock
functions. The suggested program arrangement is listed below. To program
channels 2 and 3, please follow the programming instructions listed on pages
two and three of this manual.
These transmitter buttons can be arranged for the Lock Function on the large
button and the unlock function on the small button. In this case, the combination
of both buttons operated simultaneously will control a alternate function if
installed in your vehicle.
Factory Settings for Transmitter Buttons
Channel
Button
Large
Button # 1
1
System Function
Remote Arm/Disarm
Remote Emergency Panic
Door Lock/Unlock (Optional)
Small
Button # 2
2
or
3
Unlock
or
Pulsed Output
*(Optional Devices)
Or If Programmed
Both Buttons
3
Pulsed Output
* (Optional Devices)
* Some of the more common accessories for these channels are;
AS 9075
AS 9256
AS 9154
AS 9153
Remote
Remote
Remote
Remote
Car Starter
Trunk Release Relay
Garage Door Interface
Window Roll Up
128-6463
1 of 16
Although the most common use of the transmitter buttons are shown on
the front page of this guide in bold face type, any button or button
combination can be programmed into any receiver channel. Additionally,
if both buttons are used and you require access to a 3rd channel or
function, you would program a combination of buttons to control the
3rd function. i.e... you have programmed the large button for arm,
and the small button for disarm. For channel 3, or optional
function, you can program large and small buttons operated
simultaneously. Also, if you do not program a transmitter button into
channel 2 which is the separate unlock/disarm channel, then
whatever button is programmed into channel 1 will serve as both
arm & disarm, and if used, Lock & Unlock.
PROGRAMMING TRANSMITTERS:
NOTE:
Because the system may be capable of sounding a siren, the
vehicle horn, or both, where the siren chirp is referenced below, the siren
may chirp, the horn may beep, or both devices may sound.
NOTE:
It is important to remember that during the programming mode,
each individual step must be completed within 15 seconds of the previous
step. If the 15 second time limit expires between steps, the unit will
automatically exit the program mode. Any time the ignition key is turned
off while in the program mode, the system will immediately exit program
mode. Both 15 second expiration, and ignition turning off while in the
program mode will be indicated by a long chirp from the siren & or horn.
Non alarm models will flash the parking lights only to confirm the
transmitter code has been learned and stored.
TO PROGRAM ADDITIONAL TRANSMITTERS:
1. Enter the vehicle, and turn the ignition key to the "on" position.
2. Press and release the valet push-button switch three times.
3. The dash LED will flash once, and the siren will "chirp" once, indicating
the system is ready to accept programming for channel 1 or the arm/
disarm and panic functions.
4. You can assign any of the three transmitter button functions listed below
to channel 1.
a. Pressing button #1 on the keychain transmitter.
b. Pressing button #2 on the keychain transmitter.
c. Pressing both buttons simultaneously on the keychain transmitter.
5. Press and hold the selected choice a, b, or c above, until the siren emits
a long "chirp" to confirm that programming of channel 1 was successful.
6. Press and release the valet push-button switch one time.
7. The dash mounted LED will flash 2 times, and the siren will "chirp"
2
128-6463
2 of 16
indicating that the system is ready to accept programming for the unlock/
panic channel.
(If you desire one button to control lock & unlock, move on to step 9)
8. Press and hold the selected remaining choice a, b, or c above, until the
siren emits a long "chirp" to confirm that programming of unlock channel
was successful.
9. Press and release the valet push-button switch one time.
10. The dash mounted LED will flash 3 times, and the siren will "chirp"
indicating that the system is ready to accept programming for channel
2, or the pulsed ground output for remote trunk release, remote car
starter, etc.
11. Press and hold the selected remaining choice a, b, or c above, until the
siren emits a long "chirp" to confirm that programming of channel 2 was
successful.
12. Press and release the valet push-button switch one time.
13. The dash mounted LED will flash 4 times, and the siren will "chirp"
indicating that the system is ready to accept programming for channel
3, or the additional pulsed ground output if available on your model.
NOTE: If the program switch is operated again, the circuit will recycle
through the program mode. In other words, press 1 time to access the
lock function, 2 times to access the unlock function, 3 times to access
the start function. When programming is complete, simply turn off the
ignition switch to exit the program mode.
ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN:
NOTE: Before you begin to erase the lost or stolen transmitter(s), have all
transmitters available that you wish to remain programmed. These
will be used during the program process to identify transmitters that will continue to be used.
Enter the transmitter program mode:
1. Turn the ignition switch to the “ON” position.
2. Within 10 seconds, press and release the valet/program switch three
times. (Siren emits 1 short chirp indicating channel 1 has been
entered)
3. Within 10 Seconds, press and hold the ARM or ARM/DISARM button of the first transmitter you wish to remain stored into the
control unit until a single chirp is heard from the siren.
(Repeat this for each transmitter you wish to remain stored in the control
unit).
The receiver stores up to four transmitters. To be certain all transmitter
slots in the receiver are occupied with transmitters you wish to continue
to use, and all others are erased, you will have to fill all four receiver slots.
If in step 3 you identified one transmitter, you will have to fill the additional
3
128-6463
3 of 16
3 slots. If in step 3 you identified two transmitters, you will have to fill the
additional two slots, etc...
4. Press and hold any unused button or combination of buttons until a long
chirp is heard from the siren. Release and press the button or button
combination again and again until all remaining slots are full.
NOTE: The button or combination of buttons entered will also control the arm
or arm/disarm function until additional transmitters are added. All
unwanted transmitters are now deleted.
REPRIORITIZING A TRANSMITTER’S PROGRAMMING:
To reprogram a receiver channel with a different transmitter button once a
code has been stored, there will be two options:
1. Enter the transmitter program mode of the receiver channel to be reprogrammed. Using any unused button or combination of buttons, push out
the stored code by pressing the unused button until a long chirp is heard,
then repeat 3 additional times. After this, you can add any desired
unused transmitter button. This action erases only the button stored of
the transmitter you are programming. All other codes will remain stored.
2. Enter the transmitter program mode. Using any transmitter button press
and hold until a long chirp is heard. If a single chirp or multiple chirps, (up
to 3 chirps), are heard, the unit is indicating that the transmitter has
already been programmed elsewhere in the receiver. Release the transmitter button and within 5 seconds press and hold until a long chirp is
heard. This action forces the unit to erase all stored codes of that
transmitter.
The unit then exits the program mode the siren emits the program mode exit
chirp pattern. All transmitter buttons for that transmitter must now be reprogrammed. Any other transmitter stored in the unit’s memory still remain
operational. If the button is released and not pressed again within the 5
second period, no change in programming has been made to the receiver
channel. The programmer can move onto a different channel or erase the
transmitter codes as described in 1 above.
BATTERY REPLACEMENT:
The transmitter incorporates a small LED built into the case. This LED can be
used to indicate battery condition. You will notice a decrease in transmitter
range as the battery condition deteriorates. To replace the battery...
1. Remove the transmitter cover by removing the two small screw from the
back of the transmitter case.
2. Remove the discharged battery, making note of the orientation of the + and
- contacts and dispose of the battery properly.
3. Install the new (type GP23A) battery, taking care to orient the + and contacts properly.
4. Replace the transmitter cover, taking care not to damage the LED or switches
on the circuit board.
128-6463
4 of 16
ORDER FORM FOR 2 BUTTON TRANSMITTER
MODEL NO. APS 02BT2
IMPORTANT: To help us expedite your order, please print all of the information
legibly, and mail this form and your payment according to the instructions
below.
1. Name : ______________________________________________________
Address : _____________________________________________________
City : ___________________ State : ________ Zip Code : ______________
2. Telephone Number : ( ________ ) ________________________________
3. Enter the total number of transmitters required here : ____________________
4. The cost per transmitter is $ 65.00.
5. Enter the total amount enclosed here : _______________________________
( New York state residents must include the appropriate sales tax. )
6. Method of payment; check one of the boxes below.
G Mastercard G Visa G Check or money order * (do not send cash)
* Make checks payable to Audiovox Corporation
7. Credit Card Number : ___________________________________________
8. Credit Card Expiration Date : __________________________
Credit card purchasers can order additional or replacement
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and
follow the instructions from the operator interface.
9. Mail this form and your check, to :
Audiovox Corporation
150 Marcus Blvd.
Hauppauge, N.Y. 11788
Attn: TRANSMITTER DEPARTMENT
128-6463
128-6463
5 of 16
Canal
Grand Bouton
#1
1
2
ou
3
3
128-6463
6 of 16
128-6463
7 of 16
128-6463
8 of 16
128-6463
9 of 16
128-6463
10 of 16
Canal
1
2
o
3
O Si está
programado
dos botones
3
Salida conmutada
*(Dispositivos opcionales)
9075
9256
9154
9153
128-6463
11 of 16
128-6463
12 of 16
128-6463
13 of 16
128-6463
14 of 16
THIS PAGE LEFT BLANK INTENTIONALLY
128-6463
15 of 16
128-6463
16 of 16