DeWalt DWE1622K, DWE1622 Návod na použitie

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
1-800-4-DEWALT • www.dewalt.com
b) Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286
(JUN14)
Part No. N394527
DWE1622
Copyright © 2014 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the “D” shaped
air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on
the surface of the tool.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may
result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL
US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault
circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught
in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
5) SERVICE
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety Rules for a Drill Presses
• Always use the safety chain. Mounting can release. If mounting surface does not allow the
use of the chain, then secure the unit by another means such as a clamp. Electrical power
may fail or unit may accidentally disconnect.
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss
of control.
• Keep your fingers well out of the drill area.
• The magnetic base is suitable for use on steel with a thickness of at least 3/8" (10 mm), with
no visible air gap between the magnet bottom surface and the mounting surface. Curvature,
coats of paint and surface irregularities will create an air gap. Keep the air gap to a minimum.
Air gaps between the magnet and working surface weakens the magnetic holding strength.
• Always place the magnet base on a flat surface. Do not clamp the base on small or irregularly
shaped objects.
• Always place the magnet base on a surface that is clear of shavings, chips, swarf and surface
dirt.
• Keep the magnet clean and free of debris and swarf.
• Do not switch on the motor until the drill has been mounted and installed according to the
instructions.
• Do not switch on the motor before having checked that the magnetic base has been
tightened firmly to the mounting surface.
• Before switching on the motor, make sure the accessory has been mounted correctly.
• Always use the recommended speed for the accessories and the material.
• Do not use the machine on the same workpiece on which electric welders are being used.
• Use only an appropriate cutting fluid.
• Do not use liquid cutting fluids while drilling vertical surfaces or overhead. Dip the cutter in
cutting paste or apply an appropriate spray for these applications.
• Do not pour cutting fluid into the reservoir while it is mounted on the drill. Do not allow cutting
fluid to enter the drill motor.
CAUTION: Extremely powerful magnet. Keep away from pacemakers, defibrillators,
medical equipment, computers, computer disks, cassette tapes, engine control modules, etc.
CAUTION: Do not use feed handle or power cord to lift unit.
CAUTION: After switching power to the magnet off, the magnetic base will continue to
adhere to the surface for a moment before releasing. A light blow with the hand will release
the base.
• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or
long hair can be caught in moving parts.
• An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety. The smaller the gauge number of the wire, the greater the capacity of the cable,
that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. When using more than one extension
to make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
Ampere Rating
Minimum Gauge for Cord Sets
Volts
Total Length of Cord in Feet (meters)
120 V
25 (7.6)
50 (15.2)
100 (30.5) 150 (45.7)
240 V
50 (15.2)
100 (30.5) 200 (61.0) 300 (91.4)
More
Not More
AWG
Than
Than
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V .....................volts
A.........................amperes
Hz ...................hertz
W........................watts
min .................minutes
or AC.............alternating current
or DC .....direct current
or AC/DC......alternating or direct current
no .......................no load speed
...................Class I Construction
.......................(grounded)
n .........................rated speed
...................Class II Construction
.......................earthing terminal
(double insulated)
........................safety alert symbol
…/min ............per minute
BPM ...................beats per minute
IPM .................impacts per minute
RPM ...................revolutions per minute
SPM ...............strokes per minute
sfpm ...................surface feet per minute
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool does
not operate, check power supply.
WARNING: This product is Class 1 Construction and must be connected to an
Earth connection.
WARNING: Do not operate this tool using D.C. power. It may damage the tool electronics,
which could create an unsafe condition.
COMPONENTS (Fig. 1, 4)
FIG. 1
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
H. Tool holder
A. ON/OFF power/magnet
switch
I. Safety chain (FIG. 4)
B. Off button for motor
J. Coolant bottle
C. On button for motor
K. Coolant tube
D. Gear selector
L. Quick release connector
E. Magnetic bracket
M. Flow regulator
F. Feed handle
N. Overload LED Indicator
G. Hub
O. Magnetic base
INTENDED USE
This heavy-duty drill press is designed for professional drilling applications. DO NOT use under
wet conditions or in presence of flammable liquids or gases.
This drill press is a professional power tool. DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use this tool.
E
L
G
A
2
D
K
N
1
d
rloa
ove
H
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
J
F
M
O
B C
FIG. 2
FIG. 3
R
Installing the Machine (Fig. 1, 4)
Q
1. Assemble the feed handle.
2. Fit the lubrication system as necessary.
3. Place the machine on a clean, level and solid surface. Remove any particles that will
obstruct full contact between the magnetic base (O) and the mounting surface.
4. Fit and tighten the safety chain (I).
T
F
G
Assembling the Feed Handle (Fig. 1, 2)
The quick-release feed handle (F) can be mounted in one simple operation both to the left and
the right of the machine.
1. Screw the handles (F) into the hub (G). Ensure handles are secure.
2. Keep the button (P) depressed while inserting the hub shaft into the hole (Q).
3. Release the button.
1
S
P
F
M
FIG. 4
I
O
FIG. 5
FIG. 6
2
1
2
U
1
U
Y
W
X
V
D
FIG. 7
LUBRICATION IN VERTICAL AND OVERHEAD APPLICATIONS
Dip the cutter in cutting paste or apply an appropriate spray.
2
Fitting the Safety Chain (Fig. 4)
1
Adjusting the Motor Height (Fig. 8)
The motor height can be adjusted to accommodate the need for more or less bit clearance over
the workpiece.
1. Loosen the motor slide bolt (AA) with the supplied hex key tool (BB).
2. Position the motor to the desired height.
3. Tighten the bolt firmly with the hex tool to secure the motor in position.
OPERATION
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
• Apply only a gentle pressure to the tool. Excessive force does not speed up drilling but
decreases tool performance and may shorten tool life.
• It the accessory jams, stop the motor and gently raise the accessory out of the workpiece
before resuming work.
• Always use the safety chain.
PRIOR TO OPERATION:
WARNING: Inspect the chain before each use, for wear or damage. Replace if necessary.
Try a few simple projects using scrap material until you develop a “feel” for the machine.
Switching On and Off (Fig. 1, 9)
In order to operate properly, the machine has to be switched following the procedure as
described below
SWITCHING THE POWER ON AND OFF
Plug the unit into an appropriate outlet.
To turn the power on, press the power/magnet switch (A) to the on position (I).
NOTE: Once the power is switched on the magnet will automatically be activated.
To turn the power off, press the power/magnet switch to the off (O) position.
2
2
1
1
Y
Z
D
Inserting and Removing an Accessory (Fig. 5, 6)
CAUTION: Do not change speeds while motor is running.
The machine is equipped with a two-gear selector to vary the speed/torque ratio.
1. Rotate the gear selector tab (D) out of the detent slot and shift into the desired mode.
2. Lock the selector tab back into the detent.
LOW SPEED AND HIGH TORQUE: The yellow dot (Z) should be aligned with position 1
for low speed and high torque (holes from 32 to 50 mm).
HIGH SPEED AND LOW TORQUE: The yellow dot (Z) should be aligned with position 2,
for high speed and low torque (holes from 12 to 30 mm).
NOTE : It may be necessary to slightly turn the spindle by hand a little to complete the gear
change.
D
Z
WARNING: Always use the safety chain.
Feed the provided safety chain (I) through the handle of unit and around the workpiece and
secure in place.
Setting the Speed (Fig. 7)
d
rloa
ove
LUBRICATION IN HORIZONTAL APPLICATIONS (FIG. 3)
1. Adjust the fluid flow as required using the flow regulator (M).
2. Add more cutting fluid if the shavings become blue.
3-JAW CHUCK (FIG. 6)
A 3-jaw chuck (X) can be installed using an adaptor (Y) to fit the drill press for various bit sizes.
Refer to Inserting and Removing an Accessory for installation instructions.
NOTE: It may be necessary to adjust the motor position when chuck is installed. Please refer to
Adjusting the Motor Height for instructions.
Refer to the Accessories section for further information on appropriate accessories.
K
K
FILLING THE COOLANT BOTTLE
WARNING: Do not pour cutting fluid into the bottle while mounted in the bracket. Do
not allow cutting fluid to enter the drill motor. Electric shock may result.
NOTE: The lubrication system is designed for dispensing cutting fluids specifically intended for
drilling. Other liquids may damage the system.
1. Turn the the flow regulator (M) counterclockwise to close.
2. Remove coolant bottle (J) from magnetic bracket (E).
3. Unscrew the cap (T).
4. Fill the container with cutting coolant diluted with water.
5. Screw the cap back on.
6. Place coolant bottle into magnetic bracket (E).
The tool holder accepts annular cutters with a 3/4" shank with two flats.
CAUTION: Laceration hazard. The cutter teeth are sharp.
1. Slide the pilot pin (W) through the hole in the center of the cutter shank.
2. Push up on the quick-release collar (U).
3. Insert the cutter (V) with pilot pin (W) and turn until the flat meets the locking pin. When the
flat meets the locking pin the collar will snap down.
4. Check that the cutter is securely held in the arbor.
5. Lift the collar to release the cutter.
E
L
2
Lubrication System (Fig. 1, 3)
FITTING THE LUBRICATION SYSTEM (FIG. 1, 3)
WARNING: Do not use the lubrication system in vertical surfaces or overhead drilling
applications.
Only use the lubrication system for horizontal drilling applications, as shown in Figure 1.
1. Place coolant bottle (J) into the magnetic bracket (E), slide the magnetic bracket onto the
either side of the steel strip (R).
2. Attach the coolant tube (K) to the coolant bottle:
a. Remove the nut (S) and thread it onto the tube (K).
b. Slide the tube onto the nipple and tighten the nut (S).
3. Attach the tube to the quick-release connector (L) on the gearbox.
a. Push the coolant tube (K) in to install.
b. To remove, push the collar on the connector (L) in and pull the tube from the connector.
In order to use the lubrication system, the coolant bottle (J) must be filled with a sufficient
amount of cutting fluid.
J
FIG. 9
FIG. 8
FIG. 10
A
AA
DD
2
overload
1
BB
B
N
CC
C
SWITCHING THE DRILL MOTOR ON AND OFF
WARNING: Ensure the magnet has secured the drill to the workpiece prior to turning the
motor on.
The drill motor can only be switched on when the magnet is activated.
To turn the drill motor on, press the green button (C) on the motor switch.
To turn the drill motor off, press the red button (B) on the motor switch.
RESETTING THE MACHINE
If the power is interrupted during use, or if at any point the magnetic grip is lost, the machine
must be reset.
1. Switch off the drill motor first, and then the magnet.
2. Ensure that the work area is clean.
3. Switch on the power/ magnet.
OVERLOAD PROTECTION
The DEWALT magnetic drill is fitted with an overload protection feature to prevent damage to
the motor if excessive loads are applied during operation.
The LED indicator light (N) will flash as a warning that excessive load is being applied, if this
happens reduce the pressure being applied until the light is constant green. If pressure is not
reduced the overload will activate cutting power, at which point the LED will be a solid red. If this
occurs run the unit at no load for several seconds to allow the motor to cool before resuming
the drilling operation.
Drilling a Hole (Fig. 9)
WARNING: Ensure the magnet has secured the drill to the workpiece prior to turning the
motor on.
1. Always apply an appropriate cutting fluid, coolant or lubricant on the cutting area.
2. Make sure the drill point or cutter pilot is properly installed over the spot to be drilled.
3. Press green button (C) on the motor switch to the start motor.
4. Slowly feed the accessory into the workpiece using the feed handle.
5. At the start of the cut, apply light pressure to allow the accessory to perform the initial
groove.
6. Continue applying sufficient pressure to achieve a smooth progressive cut. Do not force.
NOTE: The LED indicator light (N) will flash (red) to indicate too much pressure is being
applied, if this happens reduce the pressure being applied until the light changes to a
constant (green).
7. The pressure exerted on the handle is too high if the base comes loose from the work
surface.
9. Take extra care when the accessory is about to break through the surface to prevent
splintering.
10. Always switch off the motor and then the magnet, in that particular order, when work is
finished and before unplugging.
Drilling with Annular Cutters
1. Annular cutters only cut material at the periphery of the hole, rather than converting the entire
hole to shavings. As a result the energy required to make a hole is lower than for a twist drill.
2. When drilling with an annular cutter, it is not necessary to drill a pilot hole.
CAUTION: Do not touch the cutter or the parts close to the cutter immediately after
operation, as they may be extremely hot and cause burns to the skin. Ensure nobody is in the
work area where the metal core is ejected.
Drilling Conditions
The ease with which material can be drilled is dependent on several factors including tensile
strength and abrasion resistance. Hardness and /or strength is the usual criterion, wide
variations in machine ability can exist among material showing similar physical properties.
The drilling conditions are dependent on requirements for tool life and surface finish. These
conditions are further restricted by the rigidity of the tool and the workpiece, lubrication and
machine power available. The harder the material the lower the cutting speed. Some materials
of low hardness contain abrasive substances leading to rapid cutting edge wear at high speeds.
Feed rates are governed by rigidity of set-up, volume of material to be removed, surface finish
and available machine power.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
POP-OFF BRUSHES
The motor will be automatically shutoff indicating that the carbon brushes are nearly worn out
and that the tool needs servicing. The carbon brushes are not user-serviceable. Take the tool to
an authorized DEWALT repair agent.
Lubrication
LUBRICATING THE FEED TRAVEL (FIG. 10)
The feed travel should be lubricated periodically with grease to ensure smooth operation.
1. Raise the motor unit to the highest position possible.
2. Lubricate the dove-tail guide way (CC) at both sides.
3. Lubricate the gear rack (DD).
After repeated use, the cradle may become loose. If necessary, adjust the 5 self-locking set
screws at the left side. Tighten screws in series until the cradle moves freely in the slide but does
not allow the motor to wobble.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only DEWALT recommended accessories should be used with this product.
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DEWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including
brush inspection and replacement) should be performed by a DEWALT factory service center,
a DEWALT authorized service center or other qualified service personnel. Always use identical
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or
theft, your registration of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.
SOLAMENTE PARA PROPÓSITO DE MÉXICO:
IMPORTADO POR: DEWALT INDUSTRIAL TOOL CO. S.A. DE C.V.
AVENIDA ANTONIO DOVALI JAIME, # 70 TORRE B PISO 9
COLONIA LA FE, SANTA FÉ
CÓDIGO POSTAL : 01210
DELEGACIÓN ALVARO OBREGÓN
MÉXICO D.F.
TEL. (52) 555-326-7100
R.F.C.: BDE810626-1W7
Para servicio y ventas consulte
“HERRAMIENTAS ELECTRICAS”
en la sección amarilla.
DWE1622
120 V~
10 A
60 Hz
1200 W
300/450/min">