Manual BAXTRAN BR70

Add to my manuals
33 Des pages

publicité

Manual BAXTRAN BR70 | Manualzz

VISITE NUESTRA PÁGINA WEB :

WWW.COMPRABASCULA.COM

1

INDICADOR PESO-TARA

INDICATEUR POIDS•TARE

WEIGHT-TARE INDICATOR

Manual de usuario | Manuel d’usager | User’s guide

BR70 v4 20141001

El fabricante se reserva el derecho de modificar sin previo aviso las características de sus productos para introducir mejoras técnicas o cumplir con nuevas regulaciones oficiales./Le constructeur se réserve le droit de modifier les caractéristiques de ses produits en vue d’y apporter des améliorations techniques ou de respecter de nouvelles réglamentations./The manufacturer reserves the right to modify the specifications of its products in order to make technical improvements or comply with new regulations.

BR70 Indicador peso-tara | Indicateur poids-tare | Weight-tare indicator

ES

1. Especificaciones

2. Instalaciones

3. Descripción del teclado

4. Pantalla

5. Operaciones

› Puesta a cero de la pantalla

› Tara

› Pesar una muestra

› Contar piezas

› Comprobación de pesadas

› Acumulación de totales

6. Parámetros

7. Calibración

8. Códigos de error

9. Parámetros técnicos

FR

1. Spécifications

2. Installation

3. Description du clavier

4. Écran

5. Opérations

› Mise à zéro

› Tare

› Pesée d’un échantillon

› Fonction comptage

› Vérification de pesées

› Accumulation de totaux

6. Paramètres

7. Calibrage

8. Messages d’erreur

9. Paramètres techniques

ENG

1. Specifications

2. Installation

3. Key description

4. Display

5. Operations

› Zeroing the display

› Taring

› Weighing a sample

› Parts counting

› Check-weighing

› Accumulated total

6. Parameters

7. Calibrage

8. Error code

9.Technical parameters

23

23

24

24

26

26

27

22

22

22

22

20

20

21

22

15

15

16

16

18

18

19

14

14

14

14

12

12

13

14

8

8

7

7

10

10

11

6

6

6

6

5

6

4

4

Certificado de conformidad / Certificat de conformité / Conformity certification 29

ENG FR ES

Manual de usuario | Manuel d’usager | User’s guide 3

ES FR ENG Indicador peso-tara BR70

1. ESPECIFICACIONES

MODELO

RESOLUCIÓN

TIEMPO DE ESTABILIZACIÓN

TEMPERATURA DE TRABAJO

ALIMENTACIÓN (EXTERNA)

ALIMENTACIÓN (INTERNA)

CALIBRACIÓN

PANTALLA

CARCASA INDICADOR

RANGO DE CERO

RANGO DE LA SEÑAL DE ENTRADA

ADC

CUENTAS INTERNAS

ACTUALIZACIÓN ADC

TENSIÓN ALIMENTACIÓN CÉLULA

CÉLULAS DE CARGA

DIMENSIONES

BR70

1/15.000

1 segundo

0ºC - 40ºC / 32ºF - 104ºF

110/240 Vac, 50/60Hz batería externa automática

6 dígitos de 24 mm / LCD con retroiluminación plástico ABS

0mV ~ 5mV

0 ~ 15mV

Sigma delta

600.000

Máximo 60 veces por segundo

Max 5V/150mA

Hasta 4 células de 350 ohms

280x160x170 mm

2. INSTALACIONES

› El indicador de peso debe ser situado en un sitio que no altere ni degrade su precisión.

› Evitar temperaturas extremas. No situarlo en luz directa de sol o cerca de corrientes de aire condicionado.

› Evitar mesas inapropiadas. Las mesas o suelos deben ser rígidos y no vibrar. No debe situarse cerca de maquinaria vibrante.

› Evitar fuentes de potencia inestables. No utilizarlo cerca de grandes usos de electricidad tales como equipos de soldaduras o grandes motores.

› Evitar humedades altas que puedan causar condensaciones. Evitar contacto directo con agua. No tirar spray y evitar la inmersión de la balanza en el agua.

› Mantener el indicador de peso limpio.

› Verificar la potencia mostrada en las cantidades de potencia de la etiqueta en su área.

› Conectar los cables principales al conector en el lado del indicador. El interruptor de potencia está situado cerca del inlet principal.

› Conectar la célula de carga tal y como se indica a continuación (CUF 7 vias).

2

1

7

6

5

3 4

Para conexión 4 pines, puentear pines 1 con 2 y 5 con 6

4 Manual de usuario

BR70 Indicador peso-tara

3. DESCRIPCIÓN DEL TECLADO

ENG FR ES

CERO

Programar el punto cero para todas las pesadas siguientes. La pantalla mostrará cero.

› La función secundaria , realiza la función de tecla “Intro” cuando se programan los parámetros u otras funciones.

TARA

Tarar la balanza. Almacenar el peso actual en memoria como un valor de tara, sustraer el valor tara del peso y mostrar los resultados.

Este es el peso neto. Introducir un valor utilizando la contraseña hará que este valor sea almacenado como un valor de tara.

› La función secundaria , realiza la función de incrementar los dígitos activos cuando se programe el valor para los parámetros u otras funciones.

CAMBIO

Selecciona la información para que aparezca en pantalla cuando se cuentan las piezas y también se utiliza para otras funciones durante los modos de programación.

› La función secundaria moverá el dígito activo hacia la derecha cuando se introduzcan valores para algunas funciones.

CUENTAPIEZAS

Para selecionar el número de piezas de la muestra, dentro de la función cuentapiezas.

› La función secundaria moverá el dígito activo hacia la izquierda cuando se introduzcan valores para algunas funciones.

FUNCIÓN O SET

Utilizada para seleccionar la función de la balanza. Si la balanza está pesando va a seleccionar contado de piezas. I si no se encuentra en el modo pesar devolverá el usuario a pesar.

› Función secundaria SET (C), es para actuar como una tecla de borrado para parámetros o otras funciones.

IMPRIMIR O ESC

Para imprimir los resultados a PC o impresora utilizando la interfaz opcional RS232. También añade el valor a la memoria de acumulación si la función de acumulación no es automática.

› La función secundaria ESC, es para volver a la operación normal cuando la balanza se encuentra en modo de programación de parámetros.

UNIDAD

Cambiar la unidad de pesado.

Manual de usuario 5

ES FR ENG Indicador peso-tara BR70

4. PANTALLA

La pantalla LCD mostrará un valor y una unidad a la derecha de los dígitos. Además hay etiquetas para TARA, peso BRUTO,

CERO.

6

5. OPERACIONES

PANTALLA A CERO

Puede presionar en cualquier momento para programar el punto cero desde el cual todas las otras pesadas o las cuentas son mesuradas, entre un 4% de potencia hasta cero. Esto será normalmente sólo necesario cuando la plataforma esté vacía. Cuando se obtenga el punto cero la pantalla mostrará el indicador para cero.

La balanza tiene una función de vuelta a cero automática para responder a cualquiera desviación menor o acumulación de material en la plataforma. Sin embargo usted puede necesitar presionar para volver la balanza a cero si aparecen pequeñas cantidades de peso cuando la plataforma está vacía.

TARA

Puesta a cero de la balanza presionando si es necesario .El indicador de cero se encenderá.

Sitúe un contenedor en la plataforma, un valor para su peso aparecerá en pantalla.

Presione para tarar la balanza. EL peso que aparece en pantalla es almacenado como un valor tara y este valor se sustrae de la pantalla, dejando cero en la balanza. El indicador “TARA” se encenderá. Cuando se añade producto aparecerá sólo el peso del producto. La balanza puede ser tarada una segunda vez si otro tipo de producto se añade al primero. De nuevo, sólo el peso que se añade después de tarar aparecerá en pantalla.

Cuando se retira el contenedor aparece en pantalla un valor negativo. Si la balanza fue tarada justo antes de retirar el container este valor es el peso bruto del contenedor añadiendo todo el producto que ha sido retirado. El indicador cero también se encenderá porque la plataforma vuelve a la misma condición. Esto se produce cuando se presiona por última vez.

PESADA DE UNA MUESTRA

Para determinar el peso de una muestra primero tarar el contenedor vacío, después situar la muestra en el contenedor. La pantalla mostrará el peso y las unidades de peso en uso actualmente.

Manual de usuario

BR70 Indicador peso-tara ENG FR ES

CONTAR PIEZAS

Cuando la balanza muestra el peso, presionando empezará la función de contado de partes.

Antes de empezar, tarar el peso de cualquier contenedor a utilizar, dejando el contenedor vacío sobre la balanza. Sitúe el número de muestras sobre la balanza. El número debe coincidir con las opciones de piezas a contar, 10,20,50,100 o 200 piezas.

Presione para empezar. La balanza mostrará “ P 10” pidiendo una muestra de 10 piezas. Cambie el tamaño de la muestra presionando , la pantalla rodará a través de las opciones: 10, 20,50, 100, 200 y otra vez a 10.

Presione cuando el número coincida con el número de piezas utilizado para la muestra. Cuando se añade más peso la pantalla mostrará el número de las piezas.

Cuando esté en el modo contar, presione para mostrar la unidad de peso, peso total y cantidad (piezas).

Presione para volver a pesar de manera normal.

COMPROBACIÓN DE PESADAS

Comprobación de pesadas es un procedimiento que permite hacer sonar la alarma cuando el peso encima de la balanza se encuentre entre o exceda los valores almacenados en la memoria. La memoria contiene valores para un límite alto y un límite bajo. Cada límite puede ser utilizado o los dos a la vez.

Vea la sección PARÁMETROS para conocer los pasos a seguir para establecer los límites, se utiliza la función “FO H-L”. Cuando los límites hayan sido programados la función de comprobación de pesadas está a punto.

Cuando se sitúa un peso encima de la balanza las flechas mostrarán si el peso está por encima o por debajo de los límites y la alarma sonará tal y como se describe a continuación.

PROGRAMAR AMBOS LÍMITES

En la pantalla aparecerá OK y la alarma sonará cuando el peso se encuentre entre los límites.

PROGRAMAR LÍMITE INFERIOR

El Límite superior está programado a cero.

La pantalla mostrará OK y la alarma sonará cuando el peso sea inferior al límite inferior. Por encima del Límite Inferior la pantalla mostrará HIGH y la alarma se apagará.

PROGRAMAR LÍMITE SUPERIOR

El Límite inferior está programado a cero.

En la pantalla aparecerá LOW y la alarma estará apagada cuando el peso sea inferior al Límite Superior. Por encima del Límite superior aparecerá OK en pantalla y la alarma estará encendida.

AMBOS LIMITES PROGRAMADOS: EL LÍMITE INFERIOR ESTÁ PROGRAMADO MÁS GRANDE QUE EL SUPERIOR

La alarma no sonará nunca y la pantalla mostrará LOW si el peso es inferior al límite inferior, y HIGH si el peso es mayor al Límite

Inferior.

Nota: El peso debe ser mayor que las 20 divisiones de la balanza para poder operar con la comprobación de pesadas.

Para eliminar la función de comprobación de pesado debe introducir cero en ambos límites presionando cuando los límites actuales aparecen en pantalla, entonces presione para almacenar los valores cero.

Manual de usuario 7

ES FR ENG Indicador peso-tara BR70

ACUMULACIÓN DE TOTALES

Puede programarse la balanza para acumular manualmente presionando . Vea la sección PARÁMETROS para detalles de cómo seleccionar el método utilizando la función “F5 PRT”. La función acumulación está sólo disponible cuando se está pesando. No funciona durante el contado de piezas.

El peso que aparece en pantalla será almacenado en la memoria cuando presione y el peso se encuentre estable.

La pantalla mostrará “ACC 1” y después el total en memoria durante 2 segundos antes de volver a la normalidad. Si se instala la interfaz opcional RS232 el peso podrá salir en una impresora o PC.

Reitre el peso, permitiendo que la balanza vuelva a cero y sitúe un segundo peso sobre la balanza. Presione , la pantalla mostrará

“ ACC 2” y después el total nuevo.

Continúe hasta que se hayan añadido todos los pesos.

Para ver los totales de la memoria presione en el punto cero (el indicador CERO está encendido), para borrar la memoria, sólo presione durante la llamada de la memoria en pantalla.

Aún cuando las balanzas están programadas para mostrar en otras unidades de peso la función acumulación guarda el peso en quilogramos.

6. PARÁMETROS

La balanza tiene 6 parámetros que pueden ser programados por el usuario además de un método de introducir la sección calibración.

Para programar los parámetros presione .

La pantalla mostrará la primera función “ FO H-L”.

Presionando correrá a través de otras funciones.

Presionando le permitirá programar la función. Puede que sea necesario o bien utilizar o programar un valor utilizando la tecla

y la tecla para mover el dígito activo y después utilizar la tecla para incrementar un dígito, seguido por la tecla para introducir el valor. Utilice la tecla para dejar el parámetro sin cambiar.

Por ejemplo cuando la pantalla muestra “FO H-L” presione para empezar.

En pantalla aparecerá “Set Lo”, presione para programar el límite inferior, o presione para saltar al próximo parámetro, “Set

Hi” para programar el límite máximo.

Después de presionar para programar un límite, utilice la tecla y las teclas (CAMBIO) para cambiar el dígito parpadeante, después utilice la tecla para incrementar el dígito parpadeante. Continúe hasta el dígito próximo y prográmelo tal como necesite.

Cuando todos los dígitos han sido programados presione para almacenar el valor. La pantalla volverá al parámetro acabado de programar, en especial “Set Lo”. Avance hasta otro parámetro si lo considera necesario o presione la tecla (imprimir) para volver a pesar.

8 Manual de usuario

BR70 Indicador peso-tara ENG FR ES

FUNCIÓN

F0 H-L

F1 toL

F2 unt

F3 tl

F4 APAGAR

F5 Ser

F6

F7

Pro

SUB-FUNCIÓN DESCRIPCIÓN

SET LO › Programe un valor para el Límite Inferior

SET HI a CLR a P-C a PrT

› Programe un valor para el Límite Superior

› Borra la memoria de acumulación sin imprimir los resultados.

› Imprime la memoria total de acumulación y después borra la memoria.

› Imprime la acumulación Total, no borra la memoria.

Programe la unidad de pesar

APAGAR/ENCENDER programar dA programar tl

RELOJ bL

BEEP

K Lock usted puede seleccionar gramo (g), libras (lb), onzas, Hongkong Jin, Jin de

Taiwan

› Programe la fecha. La pantalla mostrará la última fecha programada o 00.01.01.

Introduzca nueva fecha: años.meses.días.

› Programar hora. La pantalla mostrará la hora actual. Introducir nueva hora: hh.mm.ss

› Programar apagado y encendido del reloj CLK OFF / CLK ON.

Cuando encienda el reloj, la balanza mostrará el reloj después de una parada de 5 minutos.

› Programe la retroiluminación para que esté encendida, automática o apagada.

EL ON / EL AU / EL OFF.

ON: siempre ancendida.

OFF: siempre apagada.

AU: encendido/apagado automáticamente, cuando presione cualquier tecla, añadir carga, la luz trasera se encenderá automáticamente.

› Programe la alarma a BP 1, BP 2, BP 3 durante la función comprobación de pesado.

BP 1: sin alarma.

BP 2: si el peso sobrepasa el rango de comprobación pesada, necesitará sonar.

BP 3: si el peso concuerda con el rango de comprobación de pesada, sonará.

› Bloqueo del teclado al tiempo de inutilización del visor.

VALOR POR DEFECTO kg, g, onzas, libras

Reloj apagado

EL Au

Programe el RS-232

Pcont, Seire, Ask, Wireless, Kit2, noon, Print

Acc.

Prt

Pr

LAb

PIN

Acumulación ON/OFF

P.Prt

P.Auto

1 DATE

2 HOUR

3 DATE/HOUR

0 Nº pesada/BRUTO

1 BRUTO/TARA/NET

2 BRUTO/NET inglés

3 Nº pesada/BRUTO/TARA/NET/TOTAL

Clavija introduzca los menús de programación y calibración introduciendo la contraseña correcta.

Vea la sección calibración para más detalles.

FORMATO 0

DATE:

TIME

No.

GS:

FORMATO 2

DATE:

TIME:

No.

GS:

Total:

2010 / 12 / 28

00 : 36 : 47

1

4.015kg

2010 / 12 / 28

00 : 36 : 47

3

2.765kg

9.545kg

FORMATO 1

DATE:

TIME:

No.

GS:

TW:

GW:

2010 / 12 / 28

00 : 36 : 47

2

2.765kg

0.000kg

2.765kg

FORMATO 3

DATE:

TIME:

No.

2010 / 12 / 28

00 : 36 : 47

4

GS:

TW:

2.765kg

0.000kg

GW: 2.765kg

Total: 12.310kg

Manual de usuario 9

ES FR ENG Indicador peso-tara BR70

7. CALIBRACIÓN

La balanza puede ser calibrada utilizando los siguientes procedimientos. Para un método más detallado de calibrar la balanza será necesario introducir el Menú Programación seguro. Vea detalles en la sección 12.

El indicador BR70 puede calibrar utilizando tanto los pesos métricos como en libras, dependiendo de la unidad de peso a utilizar antes de la calibración. La pantalla mostrará tanto Kg o Lb para identificar los pesos esperados.

PREOCEDIMIENTO

› Encienda la balanza.

› Encienda el interruptor, durante la cuenta de 9 a 0 presione .

› La pantalla mostrará “CAL” durante unos cuantos segundos. Mientras muestre CAL presione las teclas , y en secuencia para introducir la sección Calibración. La pantalla mostrará “unLoAd”.

› Retire cualquier peso de la plataforma. Después que el indicador se encuentre estable, presione .

› La pantalla mostrará la última calibración del valor de peso, puede utilizar las teclas , , , introducir nuevos valores de calibración (utilice las teclas , para mover el dígito activo, utilice la tecla para cambiar el valor), después de programar, presione la tecla para asegurarse, la pantalla mostrará “LoAd”. Sitúe el peso de calibración sobre la balanza. Presione .

› Si la calibración es aceptable la pantalla mostrará “PASS” y después volverá a normal. SI aparece un mensaje de error en pantalla intente la calibración otra vez ya que una distracción puede haber evitado una calibración con éxito.

› Si el problema persiste entonces contacte con su proveedor.

› Después de la calibración debe comprobarse la balanza para verificar que la calibración y la linealidad es correcta. SI es necesario repita la calibración, asegúrese especialmente que la balanza esté estable antes de aceptar cualquier peso.

10

8. CÓDIGOS DE ERROR

CÓDIGOS DE ERROR

-----

Err1

Err2

Err4

Err5

Err6

Err9

DESCRIPCIÓN

Rango excedido

Error Programación

Información

Error Programación

Hora

Error Programación

Cero

RESOLUCIÓN

Retire peso de la balanza.Si el problema persiste contacte con su distribuidor o balanzas Baxtran para asistencia

Introduzca información utilizando el formato correcto y valores razonables.Formato : año.mes.dia

Introduzca la hora utilizando el formato correcto y valores razonables.Formato: hora.minuto.segundo

La balanza se encontraba duera del rango normal de programación cero tanto cuando se ha encendido esta o cuando la tecla CERO ha sido presionada.

Retire el peso de la balanza y vuelva a intentarlo.Utilice la tecla TARA para programar la pantalla al valor cero.Si el problema persiste contacte su proveedor para asistencia.

Cortocircuito en el teclado

Inestable, no puede volver a cero

Teclado dañado

A/D fuera de rango Los valores desde el convertidor A/D estan fuera del rango normal, Reitre el peso de la balanza si esta está sobrecargada, asegúrese que la bandeja está incluida.Indica que la célula de carga o la electrónica puede ser defectuosa.Si el problema persiste contacte con su proveedor para asistencia.

Cuando encienda la balanza, si las cuenta internas no son estables, en pantalla aparecerá “Err 9”, por favor compruebe la plataforma y la célula de carga.Si el problema persiste contacte a su proveedor para asistencia.

Manual de usuario

BR70 Indicador peso-tara ENG FR ES

9. PARÁMETROS TÉCNICOS

Puede presionar , o

para introducir el modo de programación al modo PROG.

FUNCIÓN

P1 REF

P2 CAL

P3 PRO

P4 CHK

SUB-FUNCIÓN

AZN 0

0-AUTO

0-RANGO

VELOCIDAD

DECI

INC

CAP

CAL

GRA

COUNT

RESET

MODO 1

MODO 2

MODO 3

MODO 4

DESCRIPCIÓN

Esta opción se utiliza para seleccionar el auto cero y mantener la opciones: O.5d, 1d,

2d, 4d

Esta opción se utiliza para seleccionar el rango de auto cero cuando se enciende el indicador.Opciones: 0%, 2%, 5%, 10%, 20%

Esta opción se utiliza para seleccionar el rango cero manual cuando se presiona la tecla

.Opciones: 2%, 4%, 10%, 20%, 50%, 100%

Programar la velocidad ADC 7.5/15/30/60 veces/segundo

Esta opción se utiliza para seleccionar el decimal.Opciones: 0, 0.0, 0.00, 0.000

Esta opción se utiliza para seleccionar la división.Opciones: 1,2,5, 10, 20, 50

Esta pantalla mostrará xxxxx para programar la capacidad.

Calibración, vea los detalles en la SECCIÓN 10.

Parámetro ajuste factor gravedad

Esta pantalla mostrará xxxxx para indicar las cuentas internas

Esta pantalla mostrará “SURE” para recuperar los ajustes por defecto de fábrica.

Este es el modo normal de la balanza.

Este es el parámetro para ajustar la balanza para pesaje animal.

Esta es la balanza resta (imprimir “-“ peso)

Formato de impresión cómo esté programado en menú F7 PRT

Es un HOLD. Sirve para almacenar durante un periodo corto de tiempo el peso mostrado en pantalla.

Manual de usuario 11

ES FR ENG

1. SPÉCIFICATIONS

MODÈLE

RÉSOLUTION

TEMPS DE STABILISATION

TÉMPERATURE DE TRAVAIL

ALIMENTATION (EXTERNE)

ALIMENTATION (INTERNE)

CALIBRAGE

ÉCRAN

BOITIER DE L’INDICATEUR

RANG DE ZÉRO

RANG DU SIGNAL D’ENTRÉE

ADC

COMPTES INTERNES

REFRESH DE ADC

TENSION ALIMENT. CAPTEUR

CAPTEURS DE CHARGEMENT

DIMENSIONS

BR70

1/15.000

1 seconde

0ºC - 40ºC / 32ºF - 104ºF

110/240 Vac, 50/60Hz batterie externe automatique

6 digits de 24 mm / LCD display avec rétro-éclairage plastique ABS

0mV ~ 5mV

0 ~ 15mV

Sigma delta

600.000

Max 60 fois/secondes

Max 5V/150mA jusqu’à 4 capteurs d’impédance 350 ohms

280x160x170 mm

Indicateur poids-tare BR70

2. INSTALLATION

› L’indicateur de poids doit être installé dans un endroit qui n’altère pas la précision de la pesée.

› Éviter des températures extrêmes. Ne pas installer sous la lumière directe du soleil ou près d’une cliamtisation.

› Éviter les plans de travail inadéquates. Choisir un sol plat et à l’abris des vibrations.

› Ne pas l’utiliser près de grandes sources électrique comme équipements soudures ou grands moteurs.

› Éviter les univers humides qui peuvent causer des condensations. Éviter le contact direct avec l’eau. Ne pas utiliser de spray et éviter l’immersion de la balance dans l’eau.

› Maintenir l’indicateur de poids propre.

› Vérifier la puissance electrique du reseau et de l’appareil.

› Brancher les câbles principaux au connecteur de l’indicateur. L’interrupteur est près de la façade principal.

› Brancher le capteur comme suit (CUF 7 pin).

2

1

7

6

5

3 4

Pour connexion 4 pines, court-circuiter pines 1 avec 2 et 5 avec 6

12 Manuel d’usager

BR70 Indicateur poids-tare

3. DESCRIPTION DU CLAVIER

ENG FR ES

ZÉRO

Si le plateau vide, la lecture de l’écran n’est pas à zéro, appuyer sur cette touche pour corriger cette déviation. L’écran se mettra à zéro.

› La fonction secondaire , réalise la fonction de touche Intro pour accéder à la programmation des paramètres et autres fonctions.

TARE

Appuyer sur cette touche pour tarer un récipient. La balance soustraie le poids de ce dernier en mettant à zéro la lecture. Lorsque qu’un produit est introduit dans le récipient, l’indicateur affichera son poids net.

› La fonction secondaire , c’est pour augmenter le chiffre actif quand les paramètres sont réglés ou pour d’autres fonctions.

SHIFT

Pour voir toutes les données dans la fonction comptage et aussi pour régler les paramètres.

› La fonction secondaire , c’est pour déplacer le chiffre actif vers la droite pour le réglage des paramètres.

ECHANTILLON

Pour choisir le nombre de pièces de l’échantillon, dans la fonction de comptage.

› La fonction secondaire , c’est pour déplacer le chiffre actif vers la gauche dans le réglage des paramètres.

FONCTION OU SET

Pour choisir une fonction. Si la balance est en mode pesage, en appuyant sur cette touche, vous entrez dans la fonction de comptage et viceversa.

› La fonction secondaire SET (C), c’est pour effacer les valeurs dans le réglage des paràmetres.

PRINT O ESC

Pour imprimer les résultats d’un PC ou imprimante par le biais de la sortie en option de la RS-232. Elle permet aussi d’accumuler les valeurs dans le mode d’accumulations.

› La fonction secondaire ESC, c’est pour revenir au mode normal de pesage quand la balance est en mode de réglage de paràmetres.

UNITÉS

Pour changer l’unité de pesée.

Manuel d’usager 13

ES FR ENG Indicateur poids-tare BR70

4. ÉCRAN

L’écran LCD montrera une valeur et une unité à droite des digits. Écran a également des étiquettes pour montrer l’action de Tare, le poids BRUT et ZERO.

14

5. OPÉRATIONS

MISE A ZERO

Dans le cas oú, durant son utilisation, le plateau vide, l’écran n’affiche pas (0), ou que le symbole de “ZERO” ne s’affiche pas, appuyer sur pour sa correction.

L’indicateur dispose d’un système interne de correction du zéro (autozero), mais ce système se désactive quand l’appareil est taré ou a un poids sur le plateau.

TARE

Cette fonction permet de peser un produit introduit dans un récipient en obtenant d’un poids net de celui-ci.

Avec le display affichant “0”, poser le récipient sur la plateforme.

Appuyer sur , l’indicateur soustraira le poids du récipient et la lecture se mettra à zéro.

Poser le produit dans le récipient, le poids net de celui ci s’affichera.

Vous pouvez répéter les tares plusieurs fois, appuyer sur après chaque ajout de produit.

Pour revenir au mode normal de pesage, retirer le récipient de la plateforme et appuyer sur . Ainsi, l’indicateur reviendra à sa position de repos “0”.

PESER D’UN ÉCHANTILLON

Pour déterminer le poids d’un échantillon premier peser le récipient vide, puis placer l’échantillon dans le récipient.

Manuel d’usager

BR70 Indicateur poids-tare ENG FR ES

FONCTION COMPTAGE

Pour accéder à la fonction comptage, appuyer sur .

Si un récipient va être utilisé, le poser sur la plateforme et appuyer sur pour soustraire le poids.

Poser sur la plateforme ou à l’intérieur du récipient le nombre de pièces utilisées pour l’échantillonnage. Ce nombre de pièces doit coïncider avec les quantités prédéfinies de l’indicateur: 10, 20, 50, 100 ou 200 pièces.

Appuyer sur , l’écran affichera “P 10” demandant le nombre de pièces posé sur la plateforme. En appuyant sur , l’écran changera la quantité: 10, 20, 50, 100, 200. Lorsque la quantité déposée s’affiche, appuyer sur la pour confirmer.

L’indicateur a accepté l’échantillon introduit à partir de cet instant, vous pouvez ajouter le reste des pièces à compter. L’écran affichera la quantité total des pièces.

Durant la fonction de comptage, vous pouvez appuyer sur pour voir le poids unitaire, le poids total et la quantité.

Pour sortir et revenir au mode normal de pesage, appuyer sur .

VÉRIFICATION DE PESÉES

Cette fonction permet de programmer les limites de poids (inférieur et supérieur).

• Voir la section de paramètres pour configurer les valeurs des limites.

Quand vous posez un produit sur le plateau de la balance, les flèches afficheront si le poids du produit est au dessus ou en dessous des limites prédéfinies, et en émettant un bip sonore :

PROGRAMMATION DES LIMITES SUPÉRIEURE OU INFÉRIEURE

L’écran affichera le message OK et émettra un signal sonore quand le poids sera entre les deux limites.

PROGRAMMATION DE LA LIMITE INFÉRIEURE

Dans ce cas, la limite supérieur doit être programmé à zéro.

L’écran affichera le message OK et émettra un signal sonore quand le poids est en dessous de la limite inférieure.

Si le poids dépasse la valeur de la limite inférieure, l’écran affichera HIGH et le bip sonore s’arrêtera.

PROGRAMMATION DE LA LIMITE SUPÉRIEURE

Dans ce cas, la limite inférieure doit être programmé à zéro.

L’écran affichera le message LOW et le bip sonore cessera quand le poids sera inférieur à la limite inférieure.

Quand le poids est supérieur à la limite supérieure, l’écran affichera OK et émettra un bip sonore.

PROGRAMMATION DES DEUX LIMITES (la limite inférieure est programmé au dessus de la limite supérieure)

Le bip sonore ne s’activera jamais et l’écran affichera LOW si le poids est en dessous de la limite inférieure et affichera HIGH si le poids dépasse la limite inférieure.

Note: Pour que la fonction de limites fonctionnent, le poids doit être supérieure à 20 divisions.

Pour supprimer cette fonction doit introduire un zéro dans les deux limites en appuyant quand les actuelles limites se montreran dans l’écran, alors appuyez pour stocker les valeurs zéro.

Manuel d’usager 15

ES FR ENG Indicateur poids-tare BR70

ACCUMULATION DE TOTAUX

La balance peut effectuer l’accumulation de pesées de façon manuelle, en appuyant sur . Voir l’aparté des paramètres. Cette fonction est disponible seulement en mode de pesage.

Une fois le poids stable, appuyer sur , le poids sera mémorisé.

L’écran affichera “ACC 1”, puis le poids total mémorisé (pendant 2 secondes ). Dans le cas où la sortie de données RS 232 soit installée, les données seront envoyées à un PC ou une imprimante.

Retirer le produit et laisser l’écran se remettre à zéro. Poser le second poids et appuyer sur . L’écran affichera “ACC 2” et de nouveau le poids total accumulé.

Répéter la manipulation jusqu’à terminer l’opération.

Pour voir les totaux, l’écran doit être à zéro (symbole de zéro activé), appuyer sur .

Pour effacer les accumulations de la mémoire, appuyer sur au moment ou l’écran affiche les données de la mémoire.

Note: Si la balance a été réglée avec une autre unité de pesée, l’accumulation de pesée se fera toujours en Kg.

6. PARAMÈTRES

L’indicateur dispose de 6 paramètres qui peuvent être configurés par l’utilisateur et une méthode d’accéder à la section de calibrage.

Pour accéder à la configuration de paramètres, appuyer sur :

• L’écran affichera le premier paramètre “F0 H-L”

• Pour se déplacer dans les paramètres, appuyer sur .

• Pour accéder au paramètre désiré, appuyer sur .

• Pour se déplacer entre les chiffres, appuyer sur et .

• Pour augmenter la valeur du chiffre, appuyer sur .

• Pour confirmer les données introduites, appuyer sur .

• Pour sortir, appuyer sur .

Exemple pour configurer le premier paramètre “F0 H-L”:

L’écran affichera “F0 H-L”, appuyer sur pour accéder au paramètre.

L’écran affichera “Set Lo”, appuyer sur pour configurer la limite inférieure ou bien sur pour accéder au paramètre suivant. Le message “Set Hi” est pour programmer la limite supérieure.

Une fois appuyée sur pour configurer les limites, utiliser les touches et pour changer le chiffre clignotant, utiliser la touche pour augmenter la valeur du chiffre. Répéter la manipulation jusqu’à augmenter la valeur du chiffre. Répéter la manipulation jusqu’à régler tous les chiffres.

Appuyer sur pour confirmer et les mémoriser les données. L’écran reviendra au paramètre réglé. Pour sortir et revenir au mode normal de pesage, appuyer sur .

16 Manuel d’usager

BR70 Indicateur poids-tare ENG FR ES

FONCTION SUB-FONCTION DESCRIPTION

F0 H-L

F1 toL

SET LO

SET HI a CLR a P-C a PrT

› Réglage de la limite inférieure

› Réglage de la limite supérieure

› Effacer les données de l’accumulation de pesée sans imprimer les résultats.

› Effacer les données de l’accumulation de pesée et imprimer les résultats.

› Imprimer les résultats de l’accumulation sans effacer les données.

F2 unt

F3 tl

F4 OFF

F5 Ser

F6

F7

Pro

VALEUR DÉFAUT

SET dA

SET tl

Sélection de l’unité de pesée

ON/OFF vous pouvez sélectionner gram (g), libres (lb), onces, Hongkong Jin, Jin de

Taiwan

› Configuration de la date. L’écran affiche la dernière date prévue ou 00.01.01.

Entrez la nouvelle date: année.mois.jour.

› Configuration de l’heure. L’écran affiche l’heure actuelle. Entrez nouvelle heure: hh.mm.ss

CLOCK bL

BEEP

› Activer / desactiver l’heure

Quand cette fonction est activée, l’écran affichera l’heure après 5 minutes en

état de standby.

› Configuration du rétro-éclairage de l’écran:

ON: éclairage activée.

OFF: éclairage desactivée.

AU: éclairage automatique en appuyant sur une touche ou en mettant un poids sur la plateforme.

› Configuration du bip sonore en mode de limites de poids:

BP 1: Sans bip sonore.

BP 2: si le poids dépasse les limites, le bip sonore s’activera.

BP 3: si le poids est = à la limite, le bip sonore s’activera.

› Blocage du clavier au temps d’unutilisation du viseur K Lock

Configuration de la RS232

Pcont, Seire, Ask, Wireless, Kit2, noon, Print

Acc.

Prt

Pr

LAb

PIN kg, g, onces, libres

CLK off

EL Au

Acumulation ON/OFF

P.Prt

P.Auto

1 DATE

2 HEURE

3 DATE/HEURE

0 Nº PESÉES/BRUT

1 BRUT/TARE/NET

2 BRUT/NET

3 Nº PESÉES/BRUT/TARE/NET/TOTAL

English

Accéder aux menus de programation et calibrage, introduisant le mode de passe correcte.

FORMATO 0

DATE:

TIME

No.

GS:

FORMATO 2

DATE:

TIME:

No.

GS:

Total:

2010 / 12 / 28

00 : 36 : 47

1

4.015kg

2010 / 12 / 28

00 : 36 : 47

3

2.765kg

9.545kg

FORMATO 1

DATE:

TIME:

No.

GS:

TW:

GW:

2010 / 12 / 28

00 : 36 : 47

2

2.765kg

0.000kg

2.765kg

FORMATO 3

DATE:

TIME:

No.

GS:

2010 / 12 / 28

00 : 36 : 47

4

2.765kg

TW:

GW:

0.000kg

2.765kg

Total: 12.310kg

Manuel d’usager 17

ES FR ENG Indicateur poids-tare BR70

7. CALIBRAGE

› Eteindre l’indicateur et le rallumer.

› Durant le test initial de 9 à 0, appuyer sur .

› L’écran affichera “CAL” durant quelques secondes.

› Durant la visualisation de ce message, appuyer sur les touches suivantes , et pour accéder au calibrage.

› L’écran affichera “unLoAd”

› Avec le plateau vide et la lecture de l’écran stable, appuyer sur .

› L’écran affichera la dernière valeur de calibrage, pour introduire une nouvelle valeur, utiliser les touches suivantes: , , .

› Touches et pour déplacer le chiffre actif.

› Touche pour changer la valeur.

› Une fois introduit la valeur du poids de calibrage, appuyer sur pour confirmer.

› L’écran affichera “LoAd”, poser les poids de calibrage sur la plateforme.

› Appuyer sur .

› Si le calibrage est réussi, l’écran affichera “PASS” et reviendra au mode normal de pesage.

› Si l’écran indique un message d’erreur, répéter la manipulation.

8. MESSAGES D’ERREUR

CODE ERREUR

-----

Err1

Err2

Err4

Err5

Err6

Err9

DESCRIPTION

Surcharge

Erreur configuration Date

Erreur configuration Heure

Erreur configuration du Zéro

Problème de clavier

Valeurs A/D hors du rang

Instabilité, l’écran ne peut se mettre à zéro

SOLUTION

Retirer le poids de la plate-forme. Si le problème persiste, contacteur votre distributeur.

Introduire la date en utilisant le format correct. Format: yy.mm.dd

Introduire l’heure en utilisant le format correct. Formato: hh.mm.ss

La balance est hors du rang normal de zéro, autant à l’allumage ou en appuyant sur la touche . Retirer le poids de la plateforme et réessayer.

Si le problème persiste, contacter votre distributeur.

Clavier endommagé.

Si le poids posé excède la capacité maximale de la balance, le retirer.

S’assurer que la plateforme soit correctement montée.

Le capteur ou l’électronique peuvent être abîmées.

Si le problème persiste, contacter votre distributeur.

Réviser la plateforme et le capteur.

Si le problème persiste, contacter votre distributeur.

18 Manuel d’usager

BR70 Indicateur poids-tare ENG FR ES

9. PARAMÈTRES TECHNIQUES

Appuyer sur et et

pour accéder au mode de programmation PROG.

FONCTION

P1 REF

P2 CAL

P3 PRO

P4 CHK

SUB-FONCTION

AZN 0

0-AUTO

0-RANGE

SPEED

DECI

INC

CAP

CAL

GRA

COUNT

RESET

MODE 1

MODE 2

MODE 3

MODE 4

DESCRIPTION

Cette option s’utilise pour choisir l’auto-zéro. Options: O.5d, 1d, 2d, 4d

Sélection du rang de zéro automatique, lorsque la balance est éteinte. Options: 0%, 2%,

5%, 10%, 20%

Sélection du rang de zéro manuel, quand vous appuyez sur la touche .Opciones: 2%,

4%, 10%, 20%, 50%, 100%

Configuration de la vitesse ADC 7.5/15/30/60 secondes

Sélection du point decimal. Options: 0, 0.0, 0.00, 0.000

Sélection de la résolution. Options: 1,2,5, 10, 20, 50

Sélection de la capacité. L’écran affichera xxxxx pour configurer la capacité.

Calibrage, voir procédure de calibrage.

Paramètre facteur d’ajustement de gravité

L’écran affichera xxxxxx pindiquant les comptes internes.

L’écran affichera “SURE” pour revenir aux réglages originaux.

Mode normal de pesage.

Ce paramètre sert à régler la balance pour le pesage d’animaux.

C’est la balance reste (imprimer “-” pèse)

Un format d’impression comment il est programmé dans un menu F7 PRT

HOLD: C’est pour accumuler durant une courte période du temps le poids montré dans un écran.

Manuel d’usager 19

ES FR ENG

1. SPECIFICATIONS

MODEL

RESOLUTION

STABILISATION TIME

OPERATING TEMPERATURE

POWER SUPPLY (EXTERNAL)

POWER SUPPLY (INTERNAL)

CALIBRATION

DISPLAY

INDICATOR HOUSING

ZERO RANGE

SIGNAL INPUT RANGE

ADC

INTERNAL COUNTS

ADC UPDATE

LOAD CELL DRIVE VOLTAGE

LOAD CELLS

DIMENSIONS

BR70

1/15.000

1 seconds typical

0ºC - 40ºC / 32ºF - 104ºF

110/240 Vac, 50/60Hz battery automatic external

6 digits of 24 mm / LCD with backlight

ABS plastic

0mV ~ 5mV

0 ~ 15mV

Sigma delta

600.000

Max 60 times/second

Max 5V/150mA up to four 350 ohms cells

280x160x170 mm

Weight-tare indicator BR70

2. INSTALLATION

› The weighing indicator should be sited in location that will not degrade the accuracy.

› Avoid extremes of temperatures. Do not place in direct sunlight or near air conditioning vents.

› Avoid unsuitable table. The tables or floor must be rigid and not vibrate. Do not place near vibrating machinery.

› Avoid unstable power sources. Do not use near large users of electricity such as welding equipment or large motors.

› Avoid high humidity that might cause condensation. Avoid direct contact with water. Do not spray or immerse the scale in water.

› Keep the weighing indicator clean.

› Verify the voltage showing on the label matches the voltage in your area.

› Attach the mains cable to the connector on the side of the indicator. The power switch is located next to the mains inlet.

› Load cell connect as below (CUF 7 vias).

2

1

7

6

5

3 4

For connection 4 pines, to bypass pines 1 with 2 and 5 with 6

20 User’s guide

BR70 Weight-tare indicator

3. KEY DESCRIPTION

ENG FR ES

ZERO

Set the zero point for all subsequent weighing. The display shows zero.

› A secondary function , of “Enter” key when setting parameters or other functions.

TARE

Tares the scale. Stores the current weight in memory as a tare value, subtracts the tare value from the weight and shows the results.

This is the net weight. Entering a value using the keypad will store that value as the tare value.

› A secondary function , of incrementing the active digit when setting a value for parameters or other functions.

SHIFT

Selects the data to be displayed when parts counting and is used for other functions during setting modes.

› Will move the active digit to the right when setting values for some functions.

SMPL

Select sample quantities when parts counting.

› Move the active digit left when setting values for other functions.

FUNC OR SET

Used to select the function of the scale. If the scale is weighing it will select parts counting. Of it is not in weighing mode it will return the user to weighing.

› Secondary function SET(C), is to act as a clear key when setting values for parameters or other functions.

PRINT OR ESC

To print the results to a PC or printer using the optional RS232 interface. It also adds the value to the accumulation memory if the accumulation function is not automatic.

› Secondary function (ESC), is to return to normal operation when the scale is in a parameter setting mode.

UNIT

Change weighing unit.

User’s guide 21

ES FR ENG Weight-tare indicator BR70

4. DISPLAY

The LCD display will show a value and a unit to the right of the digits. In addition there are labels for TARE, GROSS weight, ZERO.

22

5. OPERATIONS

ZEROING THE DISPLAY

You can press the key at any time to set the zero point from which all other weighing and counting is measured, within 4% of power up zero. This will usually only be necessary when the platform is empty. When the zero point is obtained the display will show the indicator for zero.

The scale has an automatic rezeroing function to account for minor drifting or accumulation of material on the platform. However you may need to press the key to rezero the scale if small amounts of weight are shown when the platform is empty.

TARING

Zero the scale by pressing the key if necessary. The zero indicator will be on.

Place a container on the platform, a value for its weight will be displayed.

Press the key to tare the scale. The weight that was displayed is stored as the tare value and that value is subtracted from the display, leaving zero on the display. The “TARE” indicator will be on. As product is added only the weight of the product will be shown.

The scale could be tared a second time if another type of product was to be added to the first one. Again only the weight that is added after taring will be displayed.

When the container is removed a negative value will be shown. If the scale was tared just before removing the container this value is the gross weight of the container plus all product that was removed. The zero indicator will also be on because the platform is back to the same condition it was when the key was last pressed.

WEIGHING A SAMPLE

To determine the weight of a sample first tare the empty container then place the sample in the container. the display will show the weight and the units of weight currently in use.

User’s guide

BR70 Weight-tare indicator ENG FR ES

PARTS COUNTING

When the scale is showing weight, pressing the key will start the parts counting function.

Before beginning, tare the weight of any container that will be used, leaving the empty container on the scale. Place the number of samples on the scale. The number should match the options for parts counting, 10, 20, 50, 100 or 200 pieces.

Press the key to begin. The scale will show “P 10” asking for a sample size of 10 parts. Change the sample size by pressing the

key, the display will cycle through the options: 10,20, 50, 100, 200 and back to 10.

Press the key when the number matches the number of parts used for the sample. As more weight is added the display will show the number of parts (pcs).

When in counting mode, you can press key to show unit weight, total weight and quantity (pcs).

Press the key to return to normal weighing.

CHECK-WEIGHING

Check-weighing is a procedure to cause an alarm to sound when the weight on the scale meets or exceeds values stored in memory.

The memory holds values for a high limit and a low limit. Either limit can be used or both can be used.

See PARAMETERS SECTION for the procedure to be used to set the limits, function “F0 H-L” is used. After limits have been set the

Check-weighing function is enabled.

When a weight is placed on the scale the arrows will show if the weight is above or below the limits and the beeper will sound as described below.

BOTH LIMITS SET

The display will show OK and the beeper will sound when the weight is between the limits.

LOW LIMIT SET

High limit is set to zero.

The display will show OK and the beeper will sound when the weight is less than the Low Limit. Above the Low Limit the display will show HIGH and the beeper will be off.

HIGH LIMIT SET

Low limit is set to zero.

The display will show LOW and the beeper will be off when the weight is less than the High Limit. Above the High Limit the display will show OK and the beeper will be on.

BOTH LIMITS SET. LOW IS SET GRATER THAN HIGH

The beeper will never sound and the display will show LOW if the weight is less that the Low limit, and HIGH if the weight is greater than the Low Limit.

Note: The weight must be greater than 20 scale divisions for the checkweighing to operate.

To disable the Check-Weighing function enter zero into both limits by pressing the key when the current limits are shown then pressing to store the zero values.

User’s guide 23

ES FR ENG Weight-tare indicator BR70

ACCUMULATED TOTAL

The scale can be set to accumulate manually by pressing the . key. See the PARAMETERS Section for details of selecting the method using function “F5 PRT”. The accumulation function is only available when weighing. It is disabled during parts counting.

The weight displayed will be stored in memory when the key is pressed and the weight is stable.

The display will show “ACC 1” and then the total in memory for 2 seconds before returning to normal. If the optional RS232 interface is installed the weight will be output to a printer or PC.

Remove the weight, allowing the scale to return to zero and put a second weight on. Press the key, the display will show “ACC 2” and then the new total.

Continue until all weights have been added.

To view the totals in memory press key in zero point (ZERO indicator on), to clear the memory, just press key during memory recall display.

When the scales are set to display in other units of weight the accumulation function is still keeping the weight in kilograms.

6. PARAMETERS

The scale has 6 parameters that can be set by the user plus a method of entering the calibration section.

To set parameters press the key.

The display will show the first function, “F0 H-L”.

Pressing the key will cycle through the other functions.

Pressing key will allow you to set the function. It may be necessary to either use or set a value using the key and key to move the active digit and then using the key to increment a digit, followed by the key to enter the value. Use the key to leave a parameter unchanged.

For example when the display shows “F0 H-L” press the key to begin.

The display will show “Set Lo”, press the key to set the low limit, or press the key to skip to the next parameter, “Set Hi” for setting the high limit.

After pressing the key to set a limit, use the key and keys to change the flashing digit, then use the key to increment the flashing digit. Continue to the next digit and set it as needed.

When all digits have been set press the key to store the value. The display will go back to the parameter just set, i.e. “Set Lo”.

Advance to another parameter if needed or press the key to return to weighing.

24 User’s guide

BR70 Weight-tare indicator ENG FR ES

FUNCTION SUB-FUNCTION DESCRIPTION

F0 H-L SET LO › Set a value for the Low limit

F1 toL

SET HI a CLR a P-C

› Set a value for the High limit

› Clears the accumulation memory without printing the results.

› Prints the accumulation memory total and then clears the memory.

F2 unt a PrT

› Prints the accumulation totals, does not clear the memory.

Set weighing unit ON/OFF, you can select gram (g), pound (lb), ounce, Hon-

F3 tl

F4 OFF

SET dA

SET tl

CLOCK bL

BEEP

K Lock gkong Jin, Jin de Taiwan

› Set date, the display will show last date set or 00.01.01. Enter new time, format: yy.mm.dd

› Set time, the display will show current time. Enter new time, format: hh.mm.ss

› Set clock off or on, CLK of/CLK on. When set clock on, scale will display clock after standby for 5 minutes.

› Set the backlight to be on, automatic or off, EL on/EL au/EL off

ON: always turn on

OFF: always off

AU: automatically turn on/off, when press any key, add load, backlight will turn on automatically.

› Set the beeper to be BP1, BP2, BP3 during the check-weighing function.

BP 1: not beeper

BP 2: if the weighing overstep the rang of check-weighing, it will tweet.

BP 3: if the weight accord the rang of check-weighing, it will tweet.

› The keyboard is blocked to the time of unutilization of the visor.

F5 Prt

F6

F7

Pro

Programe el RS-232

Pcont, Seire, Ask, Wireless, Kit2, noon, Print

Acc.

Prt

Pr

LAb

PIN

Acumulation ON/OFF

P.Prt

P. Auto

1 DATE

2 HOUR

3 DATE/HOUR

0 Nº weighing/GROSS

1 GROSS/TARE/NET

2 BRUTO/NET

3 Nº weighing/GROSS/TARE/NET/TOTAL

Enter the programming and calibration menus by entering the correct password.

See the calibration section for details.

DEFAULT VALUE kg, g, ounce, lb

CLK off

EL Au

Bp3 english

FORMAT 0

DATE:

TIME

No.

GS:

FORMAT 2

DATE:

TIME:

No.

GS:

Total:

2010 / 12 / 28

00 : 36 : 47

1

4.015kg

2010 / 12 / 28

00 : 36 : 47

3

2.765kg

9.545kg

FORMAT 1

DATE:

TIME:

No.

GS:

TW:

GW:

2010 / 12 / 28

00 : 36 : 47

2

2.765kg

0.000kg

2.765kg

FORMAT 3

DATE:

TIME:

No.

GS:

2010 / 12 / 28

00 : 36 : 47

4

2.765kg

TW:

GW:

0.000kg

2.765kg

Total: 12.310kg

User’s guide 25

ES FR ENG Weight-tare indicator BR70

7. CALIBRATION

The scale can be calibrated using the following procedure. For a more detailed method of calibrating the scale it will be necessary to enter the secure Programming Menu. See detail in section 12.

The BR70 weighing indicator can calibrate using either metric or pound weights, depending on the weighing unit in use before calibration. The display will show either “kg” or “lb” to identify the weights expected.

PREOCEDURE

› Turn the power off.

› Turn the power back on, during the counting from 9 to 0 press the key.

› The display will show “CAL” for a few seconds. While it is showing “CAL” press the , and keys in sequence to enter the

Calibration section. The display will show “unLoAd”.

› Remove any weight from the platform. After stable indicator on, press the key.

› The display will show last calibrate weight value, you can use , , , key input new calibrate weight value (use , key to move active digit, use key to change value), after you setting, press key to sure, display will show “LoAd”. Place the calibration weight on the scale. Press the key.

› If the calibration is acceptable the display will show “PASS” and then return to normal. If an error message is shown try calibration again as a disturbance may have prevented a successful calibration.

› If the problem persist then contact your dealer.

› After calibration the scale should be checked to verify the calibration and linearity is correct. If necessary repeat calibration, especially be certain the scale is stable before accepting any weight.

8. ERROR CODES

ERROR CODES

-----

DESCRIPTION

Over range

Err1

Err2

Err4

Date Setting Error

Time setting Error

Zero Setting Error

Err5

Err6

Err9

Keyboard short

A/D out of range

Unstable, can’t return to zero

RESOLUTION

Remove weight from the scale.

If the problem persist contact your dealer or Baxtran scale for assistance.

Enter date using correct format and reasonable values.

Format: yy:mm:dd

Enter time using correct format and reasonable values.

Format: hh:mm:ss

The scale was outside the normal zero setting range either when it was turned on or when the key was pressed. Remove weight from the scale and try again. Use the key to set the display to zero value. If the problem persist contact your dealer for assistance.

Keyboard damaged

The values from the A/D converter are outside the normal range. Remove weight from the scale if overloaded, make sure the pan is attached. Indicates the load cell or the electronics may be faulty. If the problem persist contact your dealer for assistance.

When turn on the power, if internal counts is not stable, display will have “Err

9”, please check the platform and load cell. If the problem persist contact your dealer for assistance.

26 User’s guide

BR70 Weight-tare indicator ENG FR ES

9. TECHNICAL PARAMETERS

You can press , ,

key to enter setting mode at PROG mode.

FUNCTION

P1 REF

P2 CAL

P3 PRO

P4 CHK

SUB-FUNCTION

AZN 0

0-AUTO

0-RANGE

SPEED

DECI

INC

CAP

CAL

GRA

COUNT

RESET

MODE 1

MODE 2

MODE 3

MODE 4

DESCRIPTION

This option is used to select the auto zero maintain. Options: O.5d, 1d, 2d, 4d

This option is used to select the auto zero range when turn the indicator.

Options: 0%, 2%, 5%, 10%, 20%

This option is used to select the manual zero range when press the key. Options: 2%, 4%, 10%, 20%, 50%, 100%

Set the ADC speed 7.5/15/30/60 times/second

This option is used to select the decimal. Options : 0, 0.0, 0.00, 0.000

This option is used to select the division. Options : 1, 2, 5, 10, 20, 50

This display will show xxxxxx for setting the capacity.

Calibrate, see detail in SECTION 10.

Parameter of factor gravit adjustment.

This display will show xxxxxx for indicating the internal counts.

This display will show “SURE” for recovering the factory default setting.

This is mode of the natural scale.

This is parameter of the animal scale.

This is the scale subtract (to print “-” weigh)

Printing format how it is programmed in menu F7 PRT

HOLD: It serves to accumulate during a short period of time the weight showed in screen.

User’s guide 27

BR70 Indicador peso-tara | Indicateur poids-tare | Weight-tare indicator

DECLARACIÓN DE CONFORMIDAD

DÉCLARATION DE CONFORMITÉ

DECLARATION OF CONFORMITY

ENG FR ES

GIROPÈS S.L,

Sociedad domiciliada en

Société domiciliée à

Society domiciled in:

Polígono Empordà Internacional

C/F, parcela 15-16

17469 Vilamalla (Girona / España)

declara que los modelos de báscula

déclare que les modèles de balances declares that the models of scale

BR70 son conformes a la directiva 89/336/CEE de compatibilidad electromagnética y en su caso a las siguientes normas armonizadas:

exécutent avec les directives 89/336/CEE de compatibilité électromagnétique et à travers les suivantes règles européennes: they are according to the directive 89/336/CEE of electromagnetic compatibility and in their case to the following harmonized norms:

EN55022:2006

EN55024:1998+A1:2001+A2:2003

EN61000-3-2, 3-3

Por lo que expedimos la presente declaración de conformidad.

Par ce que nous expédions la présente déclaration de conformité.

For what we send the present declaration of conformity.

Jordi Ribalta Busquets

Manual de usuario | Manuel d’usager | User’s guide 29

marca propiedad de / marque propriété de / trade mark propiety of:

Pol. Empordà Internacional

Calle Molló, 15-16

17469 VILAMALLA

(Girona) SPAIN

T. (34) 972 527 212

F. (34) 972 527 211

publicité

Was this manual useful for you? Oui Non
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Manuels associés

Télécharger PDF

publicité

Dans d’autres langues

Seules les pages du document en Français ont été affichées