Farm King Rollermill 85, 100 FEED EQUIPMENT Operator and Parts Manual
Farm King Rollermill 85, 100 are designed to crush grains for livestock feed. The rollermill features adjustable settings to control the fineness of the rolled feed, allowing you to customize the feed to meet the specific needs of your animals. The hopper is designed to be partially filled at all times while the rollermill is running, ensuring even rolling and preventing uneven wear on the rollers. The optional magnet for the intake hopper helps keep small metal objects out of the rolled feed and prevents damage to the roller grooves.
advertisement
#85 & #100 Rollermill
- 1 -
WARRANTY REGISTRATION AND POLICY
Buhler Manufacturing products are warranted for a period of twelve (12) months from
original date of purchase, by original purchaser, to be free from defects in material and
workmanship under correct, normal agricultural use and proper applications.
Buhler Manufacturing’s obligations under this warranty shall be limited to the repair or
exchange, at Buhler Manufacturing’s option, of any Buhler Manufacturing product or
part which proves to be defective as provided. Buhler Manufacturing reserves the right
to either inspect the product at the buyer’s location or have it returned to the factory for
inspection.
The above warranty does not extend to goods damaged or subject to accident, abuse or
misuse after shipment from Buhler Manufacturing’s factory, nor to goods altered or
repaired by anyone other than an authorized Buhler Manufacturing representative.
Buhler Manufacturing makes no Express Warranties other than those, which are
specifically described. Any description of goods, including any references and
specifications in catalogues, circulars and other written material published, is for the
sole purpose of identifying goods and shall conform to such descriptions. Any sample
or model is for illustrative purposes only and does not create an Express Warranty that
the goods conform to sample or model shown.
The purchaser is solely responsible for determining suitability of goods sold. This
warranty is expressly in lieu of all other warranties expressed or implied. Buhler
Manufacturing will in no event be liable for any incidental or consequential damages
whatsoever. Nor for any sum in excess of the price received for the goods for which
liability is claimed.
WARRANTY CLAIMS:
Warranty requests must be prepared on Buhler Manufacturing Warranty Claim Forms
with all requested information properly completed. Warranty Claims must be submitted
within a thirty (30) day period from date of failure repair.
WARRANTY LABOR:
Any labor subject to warranty must be authorized by Buhler Manufacturing. The labor
rate for replacing defective parts, where applicable, will be credited at a rate determined
by the Company, Buhler Manufacturing.
IMPORTANT FACTS:
Buckets and Bucket Tines Carry No Warranty
Bent Spears Carry No Warranty
Snowblower Fan Shafts Carry No Warranty
Mower Blades Carry No Warranty
Portable Auger Parts Have Two (2) Year Warranty
- 1 -
WARRANTY REGISTRATION AND POLICY
Buhler Manufacturing products are warranted for a period of twelve (12) months from
original date of purchase, by original purchaser, to be free from defects in material and
workmanship under correct, normal agricultural use and proper applications.
Buhler Manufacturing’s obligations under this warranty shall be limited to the repair or
exchange, at Buhler Manufacturing’s option, of any Buhler Manufacturing product or
part which proves to be defective as provided. Buhler Manufacturing reserves the right
to either inspect the product at the buyer’s location or have it returned to the factory for
inspection.
The above warranty does not extend to goods damaged or subject to accident, abuse or
misuse after shipment from Buhler Manufacturing’s factory, nor to goods altered or
repaired by anyone other than an authorized Buhler Manufacturing representative.
Buhler Manufacturing makes no Express Warranties other than those, which are
specifically described. Any description of goods, including any references and
specifications in catalogues, circulars and other written material published, is for the
sole purpose of identifying goods and shall conform to such descriptions. Any sample
or model is for illustrative purposes only and does not create an Express Warranty that
the goods conform to sample or model shown.
The purchaser is solely responsible for determining suitability of goods sold. This
warranty is expressly in lieu of all other warranties expressed or implied. Buhler
Manufacturing will in no event be liable for any incidental or consequential damages
whatsoever. Nor for any sum in excess of the price received for the goods for which
liability is claimed.
WARRANTY CLAIMS:
Warranty requests must be prepared on Buhler Manufacturing Warranty Claim Forms
with all requested information properly completed. Warranty Claims must be submitted
within a thirty (30) day period from date of failure repair.
WARRANTY LABOR:
Any labor subject to warranty must be authorized by Buhler Manufacturing. The labor
rate for replacing defective parts, where applicable, will be credited at a rate determined
by the Company, Buhler Manufacturing.
IMPORTANT FACTS:
Buckets and Bucket Tines Carry No Warranty
Bent Spears Carry No Warranty
Snowblower Fan Shafts Carry No Warranty
Mower Blades Carry No Warranty
Portable Auger Parts Have Two (2) Year Warranty
#85 & #100 Rollermill
- 2 -
ASSEMBLY INSTRUCTIONS
1. Both the #85 and the #100 Rollermills are completely assembled except for
the intake hopper (#57). Bolt the hopper to the top of the rollermill using
bolts supplied with the hopper.
2. An optional stand with braces (#65 & #66) is available for both models.
Bolt the stand underneath the rollermill using 3/8" x 1 ¼” hex bolts, lock
washers and hex nuts for the braces and ½” x 1 ¼” hex bolts on the stand.
3. A belt drive kit consisting of a 15" single pulley, one B-58 V-belt and a
motor mount is supplied with the #85 rollermills. A 3 h.p. electric motor is
required for the motor drive. The #85 can also be run with a PTO shaft.
The #100 rollermill may be purchased with either a belt drive kit consisting
of a 15" double pulley, two B-62 V-belts and a motor mount or a PTO
shaft for PTO drive. A 5 h.p. electric motor is used for the motor drive.
The electric motor pulley must be supplied by the customer. The #85
rollermill requires a 4 ½”, B-groove single pulley. A double 4 ½” pulley is
required for the #100 rollermill electric motors should be 1750 rpm.
4. A magnet for the intake hopper is available as an option for all rollermills.
This will keep small metal objects out of the rolled feed and also prevent
damage to the roller grooves.
5. OPTIONAL PTO DRIVE ONLY: With the engine on the tractor shut off,
attach the PTO shaft. The tractor end has a standard 6-spline end with a
spring loaded locking pin. The rollermill end has a clamp-style yoke with a
3/8" keyway. Slide the yoke onto the roller shaft with the 3/8" key
supplied. Lock the yoke in place with the ½” x 2 ¾” fine thread bolt and
lock nut fitted through the groove in the roller shaft. After tightening the
bolt, insert and tighten the 3/8" socket set screw supplied.
CAUTION: Always check to see that both ends of the PTO shaft are
securely attached every time the rollermill is used. This should always be
done with the tractor engine off.
- 2 -
ASSEMBLY INSTRUCTIONS
1. Both the #85 and the #100 Rollermills are completely assembled except for
the intake hopper (#57). Bolt the hopper to the top of the rollermill using
bolts supplied with the hopper.
2. An optional stand with braces (#65 & #66) is available for both models.
Bolt the stand underneath the rollermill using 3/8" x 1 ¼” hex bolts, lock
washers and hex nuts for the braces and ½” x 1 ¼” hex bolts on the stand.
3. A belt drive kit consisting of a 15" single pulley, one B-58 V-belt and a
motor mount is supplied with the #85 rollermills. A 3 h.p. electric motor is
required for the motor drive. The #85 can also be run with a PTO shaft.
The #100 rollermill may be purchased with either a belt drive kit consisting
of a 15" double pulley, two B-62 V-belts and a motor mount or a PTO
shaft for PTO drive. A 5 h.p. electric motor is used for the motor drive.
The electric motor pulley must be supplied by the customer. The #85
rollermill requires a 4 ½”, B-groove single pulley. A double 4 ½” pulley is
required for the #100 rollermill electric motors should be 1750 rpm.
4. A magnet for the intake hopper is available as an option for all rollermills.
This will keep small metal objects out of the rolled feed and also prevent
damage to the roller grooves.
5. OPTIONAL PTO DRIVE ONLY: With the engine on the tractor shut off,
attach the PTO shaft. The tractor end has a standard 6-spline end with a
spring loaded locking pin. The rollermill end has a clamp-style yoke with a
3/8" keyway. Slide the yoke onto the roller shaft with the 3/8" key
supplied. Lock the yoke in place with the ½” x 2 ¾” fine thread bolt and
lock nut fitted through the groove in the roller shaft. After tightening the
bolt, insert and tighten the 3/8" socket set screw supplied.
CAUTION: Always check to see that both ends of the PTO shaft are
securely attached every time the rollermill is used. This should always be
done with the tractor engine off.
#85 & #100 Rollermill
- 3 -
OPERATING INSTRUCTIONS
Before using the Rollermill, check the clearance on the rollers. Place a piece of
newspaper between the rollers and adjust the set screws on either side of the rollermill
till you can feel a slight tension on the paper. The rollers, however, should not touch
each other. It is very important that the rollers are evenly adjusted. To ensure good
rolling results, check roller adjustment regularly and reset if necessary.
Close the gate control (#20) before starting the rollermill. The intake hopper should be
partially full before opening the gate control. Keep the hopper partially filled at all times
while the rollermill is running. This will allow the grain to be rolled evenly across the
width of the roller and will result in more uniformly rolled feed. It also helps prevent the
rollers from wearing unevenly. Before stopping the rollermill, close the gate control
while there is still grain in the hopper. When the grain remaining in the machine has all
been crushed, shut off the machine immediately. The gate control is left closed until the
machine is started again.
To regulate the type of rolled feed one wants, use the adjusting screw (#47). Increased
pressure will result in finer and flatter feeds. Decreasing the tension will give you a
coarser feed. The roller bearing should be greased approximately every 80 hours or
once a season if used less.
ALERT: When replacing bearings or tightening a loose bearing collar, always tighten
collar in the direction of shaft rotation using a center punch or a similar tool.
- 3 -
OPERATING INSTRUCTIONS
Before using the Rollermill, check the clearance on the rollers. Place a piece of
newspaper between the rollers and adjust the set screws on either side of the rollermill
till you can feel a slight tension on the paper. The rollers, however, should not touch
each other. It is very important that the rollers are evenly adjusted. To ensure good
rolling results, check roller adjustment regularly and reset if necessary.
Close the gate control (#20) before starting the rollermill. The intake hopper should be
partially full before opening the gate control. Keep the hopper partially filled at all times
while the rollermill is running. This will allow the grain to be rolled evenly across the
width of the roller and will result in more uniformly rolled feed. It also helps prevent the
rollers from wearing unevenly. Before stopping the rollermill, close the gate control
while there is still grain in the hopper. When the grain remaining in the machine has all
been crushed, shut off the machine immediately. The gate control is left closed until the
machine is started again.
To regulate the type of rolled feed one wants, use the adjusting screw (#47). Increased
pressure will result in finer and flatter feeds. Decreasing the tension will give you a
coarser feed. The roller bearing should be greased approximately every 80 hours or
once a season if used less.
ALERT: When replacing bearings or tightening a loose bearing collar, always tighten
collar in the direction of shaft rotation using a center punch or a similar tool.
#85 & #100 Rollermill
- 4 -
SAFETY INSTRUCTIONS
1. Keep hands out of intake hopper when machine is in operation.
2. Keep hands, feet and clothing away from moving parts.
3. Shut off power to adjust, service or clean.
4. Make certain electric motors are grounded.
5. Keep everyone away when machine is in operation. Belts and PTO joints
require a particular amount of caution.
6. Keep all guards in place when machine is in operation.
- 4 -
SAFETY INSTRUCTIONS
1. Keep hands out of intake hopper when machine is in operation.
2. Keep hands, feet and clothing away from moving parts.
3. Shut off power to adjust, service or clean.
4. Make certain electric motors are grounded.
5. Keep everyone away when machine is in operation. Belts and PTO joints
require a particular amount of caution.
6. Keep all guards in place when machine is in operation.
5
6
7
8
9
10
11
12
13
14
15
advertisement
Key Features
- 12-month warranty
- Adjustable settings for controlling the fineness of the rolled feed
- Optional magnet for the intake hopper to keep small metal objects out of the rolled feed
- Portable Auger Parts Have Two (2) Year Warranty
Related manuals
Frequently Answers and Questions
What is the warranty period for the Farm King Rollermill 85, 100?
12 months from the original date of purchase.
How do I adjust the fineness of the rolled feed?
Use the adjusting screw (#47) to increase or decrease the pressure on the rollers.
How often should I grease the roller bearing?
Approximately every 80 hours or once a season if used less.
Is there a magnet available for the intake hopper?
Yes, an optional magnet is available to keep small metal objects out of the rolled feed.
advertisement
