Ultra Classic II | MICROTAC DPC 650 | Motorola 8000 Classic, Ultra Classic, Classic II, Micro-Tac Flip, 95xx mobile phone User manual

Show PDF Add to My manuals
27 Pages

advertisement

1
MOTOROLA USERS AND PROGRAMMING GUIDES
Original author: Mike Larsen 01/23/95 03/26/95
[email protected] [email protected]
Additional information, graphics, other articles, and conversion to Word by Bob 03/20/95 v1.1 by Bob 3/21/95.
This is mainly a compilation of other peoples work. I, Bob, to not seek credit for something I did not do. I
however will be more then happy to take credit for what I did do. I compiled most of the data you see before you.
I took Mike Larsen’s manual, changed a few things, and added to it. I also turned a few documents into TIFs for
ease of reading. This manual was designed to make a nice printed copy of the data gathered by all parties
involved. Authors names remain intact throughout this document, and in most cases, the data has not be changed.
This manual may be altered to each users needs. Further, each user may add to this manual, and is encouraged to
do so. Further, each user may retransmit this manual in it’s altered state, provided the user credits all involved.
Further, the user may quote from this manual, provided the user credits the correct author, and makes a vague
reference to “Bob”. This manual may not be sold in any form for any amount of money, unless all authors
involved agree. Further, all data within this manual can not be sold in any for any amount of money unless the
appropriate author/s agree. However, learned procedures may be used to aid ones employment, or be used in the
gain of money, provided that such procedures are documented with this manual, or the information pertaining to
the procedure. In short: This information is to be shared with all who have an interested, and is ment to benefit
the users of the Motorola cellular phone, and the authors by being credited for the gathering of this information.
My special `contribularity` to Mike Larsen, Dr. Who, who compiled most of the hard data contained in this
manual. --bob
TABLE OF CONTENTS
BASIC COMMANDS 3
NAM PROGRAMMING 4
TEST MODE ACCESS: 6
INSTALLED MOBILE PHONES AND TRANSPORTABLE MODELS 6
HAND HELD PORTABLE MODELS: 6
8000 & ULTRA CLASSIC SERIES: 6
MICRO-TAC "FLIP" SERIES: 7
GENERAL NOTES: 7
NEWER 95xx PHONES (Thank you Motorola!!!) 7
ULTRA CLASSIC II SERIES: 7
LOCK/UNLOCK PROCEDURES: 7
SYSTEM SELECT PROCEDURES: 8
TEST MODE 8
TEST MODE PROGRAMMING: 9
TEST MODE PROGRAMING DATA: For AMPS and NAMPS Cellular Telephones 9
TEST MODE PROGRAMING DATA: For TDMA Cellular Telephones 10
NOTES: 10
TEST MODE COMMANDS: 12
2
GSM INFO AND TEST MODES. 14
TESTMODE for GSM PHONES: 14
Security Codes on the GSM phones: 16
Undocumented Menu shortcuts (7500, 8200, and maybe the 5200 and 7200) 16
Test Mode Functions: 17
HACKING THE FOVC 18
ASSEMBLING A _QUALITY_ MOTOROLA FLIP PROGRAMMING CABLE19
PINOUTS FOR MOTOROLA 8000 “BRICK” PHONE - “N” SERIES 22
15 PIN CABLE PINOUTS 22
OEM 32 PIN CABLE PINOUTS 22
CVC BLOCK 23
NEW EXTERNAL CONNECTOR FOR THE ULTRA CLASSIC II CVC
PINBLOCKS 23
PINOUTS FOR MOTOROLA SERIES 2 AND 3 TRANSCEIVERS 25 PIN
CABLE PIN DEFINITIONS 23
FLIP FONES AND ALL FONES USING THE DPC/PT FLIP CABLE 24
MOTOROLA / AMPS HANDSET SPECIFICATIONS: 24
MOTOROLA ESN RANGES 24
CELLULAR FREQUENCY LIST 25
3
Basic Commands
Before going in to the programming of the cellular phone, it is important for the user to know
the normal things necessary for day to day operation. While the majority of the stuff in the users
manual is intended for people that have problems programming their VCR, their are a few things that
are very important and are only mentioned in the users manual.
Turn On or Off [Pwr]
Place Call Enter number, [Snd]
Receive Call [Snd] or open flip fone
End Call [End] or close flip fone
Automatic Redial To retry call, press [Snd] before ending the unsuccessful call
attempt.
Store Number Phone number, [Sto], 2-digit location number or press [*] to
autoload. If phone is Alphanumeric, display will flash
"Alpha_". Press [Sto] to bypass or use keypad to enter letter (up
to 14). [#] advances to next position, [*] backspaces. When
finished, press [Sto].
Recall Number [Rcl], 2-digit location number. Entering location 01, then
hitting [#] will allow scrolling through all stored locations.
Recall Name Press [Name/Menu], [#] or [*] to scroll. [Rcl] will display
location number then name, [Rcl] again will display
corresponding phone number and [Snd] to dial.
Recalling Last 10 Numbers Called [Rcl], [0], [0]. Display will show "L0'" followed by the name or
number of the most recently placed call. Use [#] or [*] to scroll
and [Snd] to call displayed number.
Super Speed Dialing Directory location number, [Snd]
Changing Entries Press [Rcl] and the 2-digit location number so that the number
to be changed is displayed. Press and release [Clr] to back out
each of the digits. Enter a new number and press [Sto].
Call Number Displayed [Snd]
Microphone Muting Press [Fcn], [6]. To unmute, press [Fcn], [6]
Lock Unit [Fcn], [5] or [LOCK]
Unlock Three digit unlock code. If you make an error, [Clr] and enter
again.
Automatic Lock [FCN], [6] (not all phones) "EnAbLE" will appear if
compatible.
Display Unlock Code Press [Fcn], [0], your six-digit security code, [Rcl].
Changing Your Unlock Code Press [Fcn], [0], your six-digit security code, your NEW 3-digit
unlock code, [Sto].
Review Battery Meter Press [Fcn], [4] and release.
Adjust Volume Earpiece - Press and hold [Vol] to increase. Release, press again
to decrease. Ringer - [Fcn], then Vol as above.
Recall Own Phone Number [Rcl], [#]
Individual Call Timer [Rcl], [#], [#]
Resettable Call Timer [Rcl], [#], [#], [#]
Reset Resettable Call Timer [Fcn], [0], [7], [Clr]
Cumulative Call Timer [Rcl], [#], [#], [#], [#]
Access Features Press [Fcn], [1]. To change features, press [*] and [#] to scroll
and [Clr] to change. To exit feature menu, press [END].
Review/Scroll Menu Features Press [*] or [#]
Status Review [Fcn], [0], [9], [Rcl], [#] or [*] scrolls messages. To end press
[END].
Changing System Type Press [Rcl], [*]. Repeatedly press [*] until the desired system
type appears. To select press [Sto].
Outgoing Call Restrictions Press [Fcn], [0], 6-digit security code, [1], [Sto]. Phone will
place calls only from memory locations 1-10. To change back to
unrestricted dialing press [Fcn], [0], 6-digit security code, [4],
[Sto].
Switch to Second Phone Number [Rcl], [#], [Sto] (Press [Clr] to finish viewing newly activated
number).
4
NAM Programming
Once the phone model and sequence number are identified, determine the program access sequence
from this list.
HAND HELD PORTABLE MODELS
If the phone has a FCN button and no MENU button use sequence 1.
If the phone has no FCN button use sequence 2.
If the phone has a MENU button and a FCN button use sequence 4.
INSTALLED MOBILE PHONES AND TRANSPORTABLE MODELS
If the phone has no FCN button and no RCL button use sequence 3.
If the phone has a FCN button use sequence 4.
If the phone has a MEM button use sequence 5.
If the phone has a RCL button and no FCN button use sequence 6.
SEQUENCE# ACCESS CODE
1 FCN (SECURITY CODE TWICE) RCL
2 STO # (SECURITY CODE TWICE) RCL
3 CTL 0 (SECURITY CODE TWICE) *
4 FCN 0 (SECURITY CODE TWICE) RCL
5 FCN 0 (SECURITY CODE TWICE) MEM
6 CTL 0 (SECURITY CODE TWICE) RCL
The default security code is 000000. The CTL (control) button is the single black button on the side of
the handset. If the security code is unknown then you can obtain it via TEST MODE access.
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
  • Page 1
  • Page 2
  • Page 3
  • Page 4
  • Page 5
  • Page 6
  • Page 7
  • Page 8
  • Page 9
  • Page 10
  • Page 11
  • Page 12
  • Page 13
  • Page 14
  • Page 15
  • Page 16
  • Page 17
  • Page 18
  • Page 19
  • Page 20
  • Page 21
  • Page 22
  • Page 23
  • Page 24
  • Page 25
  • Page 26
  • Page 27
/

advertisement

Key Features

  • Make and receive calls
  • Store phone numbers
  • Manage various settings
  • Test mode access
  • Advanced programming
  • Troubleshooting

Related manuals

Frequently Answers and Questions

How do I turn on or off my Motorola cellular phone?
Simply press the [Pwr] button to turn the phone on or off.
How do I place a call on my Motorola cellular phone?
Enter the phone number you wish to call, and then press the [Snd] button.
How do I store a phone number in my Motorola cellular phone?
Enter the phone number, press the [Sto] button, then enter a 2-digit location number or press [*] to autoload. If the phone is alphanumeric, the display will flash "Alpha_". Press [Sto] to bypass or use the keypad to enter a letter (up to 14). [#] advances to the next position, [*] backspaces. When finished, press [Sto].
How do I lock or unlock my Motorola cellular phone?
Phones with "LOCK" buttons: Press lock for at least 1/2 a second. Phones with a "FCN" button: Press FCN 5. Phones with no FCN or LOCK button: Press Control 5.
How do I access test mode on my Motorola cellular phone?
The procedure for entering test mode varies depending on the model of your phone. Refer to the "TEST MODE ACCESS" section in the manual for detailed instructions based on your phone's series.

advertisement