CAME BK-1200P Sliding Gate Opener Installation manual
CAME BK 1200 is a powerful and reliable automation system designed for sliding gates in residential and condominium complexes. With a maximum gate weight capacity of 1200 kg and a maximum length of 14 meters, this gearmotor ensures smooth and efficient operation.
advertisement
BK SERIES
BK-1200P
AUTOMATION WITH “PRATICO SYSTEM”
FOR SLIDING GATES
INSTALLATION MANUAL
BK-1200P
AUTOMATION WITH “PRATICO SYSTEM”
FOR SLIDING GATES
INSTALLATION MANUAL
2
All the data and information contained herein is considered subject to change at any time and at our discretion
ENGLISH
2.1 Destination
1 Legend
2 Destination and limits of use
The BK-1200P gearmotor is designed to automate sliding gates for residential and condominium complexes.
The use of this product for purposes other than the one intended and installation carried out in a manner other than as
instructed in this technical manual are prohibited.
2.2 Limits of use
For intensive or condominium use: maximum gate weight 1200 kg with maximum length of 14 meters.
#
#
This symbol indicates sections to be read with particular care.
This symbol indicates sections concernig safety
This symbol indicates notes to communicate to users.
“IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION”
“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”
“THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS”
The following standard were complied with for this product: EN 12978, UNI EN 954-1, CEI EN 60335-1, UNI EN 12453.
3 Standard followed
4.1 Gearmotor
The BK-1200P ratiomotor is designed and built by CAME CANCELLI AUTOMATICI S.p.A. and it meets the safety standards in force.
Guaranteed 24 months if not tampered with.
The case consists partly of cast aluminium, inside of which operates the non-reversible electromechanical gearmotor, and partly
of a covering in ABS plastic inside of which is an electronic card, the transformer and the emergency battery holder.
The BK-1200P ratiomotor may be supplied with complementary accessories such as:
001 R001 - Lock cylinder with DIN keys;
001 BSF - Braking device for gates installed on a sloping surface;
001 BRC5/10/15 - Power supply cable winding device for sensitive safety profi les;
001 B4353 - Chain transmission device;
009 CGZ - Galvanized steel 22 x 22 module 4 rack;
009 CGZS - Galvanized steel 30 x 8 module 4 rack with fastening screws, holes and supports;
009 CCT - Simple 1/2” chain;
009 CGIU - 1/2” chain joint.
Important! Check that the safety equipment and accessories are CAME originals; this is a guarantee that also makes the system
easy to set up and upkeep.
4 Description
4.2 Technical information
GEARMOTOR
Power supply: 230V A.C. 50/60Hz
Motor power supply: 230V A.C. 50/60Hz
Max. absorption: 3,3 A
Rated power: 380 W
Max. torque: *31 Nm
Reduction ratio: 1/11
Push: 850 N
Max. speed: 14,5 m/min
Operation intermittence: 30%
Protection level: IP54
Weight: 18 kg
Condenser: 31,5 µF
Engine thermoprotection: 150° C
Operating temperature:* Obtained with CAME control panel.
All the data and information contained herein is considered subject to change at any time and at our discretion
ENGLISH
2.1 Destination
1 Legend
2 Destination and limits of use
The BK-1200P gearmotor is designed to automate sliding gates for residential and condominium complexes.
The use of this product for purposes other than the one intended and installation carried out in a manner other than as
instructed in this technical manual are prohibited.
2.2 Limits of use
For intensive or condominium use: maximum gate weight 1200 kg with maximum length of 14 meters.
#
#
This symbol indicates sections to be read with particular care.
This symbol indicates sections concernig safety
This symbol indicates notes to communicate to users.
“IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION”
“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”
“THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS”
The following standard were complied with for this product: EN 12978, UNI EN 954-1, CEI EN 60335-1, UNI EN 12453.
3 Standard followed
4.1 Gearmotor
The BK-1200P ratiomotor is designed and built by CAME CANCELLI AUTOMATICI S.p.A. and it meets the safety standards in force.
Guaranteed 24 months if not tampered with.
The case consists partly of cast aluminium, inside of which operates the non-reversible electromechanical gearmotor, and partly
of a covering in ABS plastic inside of which is an electronic card, the transformer and the emergency battery holder.
The BK-1200P ratiomotor may be supplied with complementary accessories such as:
001 R001 - Lock cylinder with DIN keys;
001 BSF - Braking device for gates installed on a sloping surface;
001 BRC5/10/15 - Power supply cable winding device for sensitive safety profi les;
001 B4353 - Chain transmission device;
009 CGZ - Galvanized steel 22 x 22 module 4 rack;
009 CGZS - Galvanized steel 30 x 8 module 4 rack with fastening screws, holes and supports;
009 CCT - Simple 1/2” chain;
009 CGIU - 1/2” chain joint.
Important! Check that the safety equipment and accessories are CAME originals; this is a guarantee that also makes the system
easy to set up and upkeep.
4 Description
4.2 Technical information
GEARMOTOR
Power supply: 230V A.C. 50/60Hz
Motor power supply: 230V A.C. 50/60Hz
Max. absorption: 3,3 A
Rated power: 380 W
Max. torque: *31 Nm
Reduction ratio: 1/11
Push: 850 N
Max. speed: 14,5 m/min
Operation intermittence: 30%
Protection level: IP54
Weight: 18 kg
Condenser: 31,5 µF
Engine thermoprotection: 150° C
Operating temperature:* Obtained with CAME control panel.
#!-%
MAX
7
1
3
2
4 5
6
3
4
2
8
7
16
5
8
9
10
4.4 Size measurements
Measurements in mm
3
All the data and information contained herein is considered subject to change at any time and at our discretion
ENGLISH
4.3 Parts description
GEARMOTOR UNIT
1 - Gearmotor
2 - Board cover support
3 - End-stop flaps
4 - ZBK8 basic control board
5 - Electric board front cover
6 - Release door
7 - Base plate
8 - Securing screws
9 - Plates for securing screws
10 - Nuts
ACCESSORIES
1 - R001 - Cylinder lock with DIN keys
2 - BSF - Braking device
3 - BRC - Cable winding device
4 - B4353 - Chain transmission device
5 - CCT - Simple 1/2” chain
6 - CGIU - 1/2” chain joint
7 - CGZ - Galvanized steel 22 x 22 module 4 rack
8 - CGZS - Galvanized steel 30 x 8 module 4 rack
with fastening screws, holes and supports
MAX
7
1
3
2
4 5
6
3
4
2
8
7
16
5
8
9
10
4.4 Size measurements
Measurements in mm
3
All the data and information contained herein is considered subject to change at any time and at our discretion
ENGLISH
4.3 Parts description
GEARMOTOR UNIT
1 - Gearmotor
2 - Board cover support
3 - End-stop flaps
4 - ZBK8 basic control board
5 - Electric board front cover
6 - Release door
7 - Base plate
8 - Securing screws
9 - Plates for securing screws
10 - Nuts
ACCESSORIES
1 - R001 - Cylinder lock with DIN keys
2 - BSF - Braking device
3 - BRC - Cable winding device
4 - B4353 - Chain transmission device
5 - CCT - Simple 1/2” chain
6 - CGIU - 1/2” chain joint
7 - CGZ - Galvanized steel 22 x 22 module 4 rack
8 - CGZS - Galvanized steel 30 x 8 module 4 rack
with fastening screws, holes and supports
5.1 Preliminary checks
Before proceeding with the installation, it is necessary to:
• Make sure the door is rigid and compact and that the sliding wheels are well oiled and in good condition.
• The ground guide must be well fastened to the ground, fully on the surface for the entirety of its length and without irregularities
that might obstruct the gate’s movement.
• The upper guide runners must not create friction.
• Provide for a gate stopper for opening and one for closing, and for the path of electrical cables as per standard system.
• Make sure the point in which the ratiomotor is fixed is in an area protected from shocks or bumps, and that the anchoring
surface is solid.
• Provide for suitable omnipolar disconnection device with more than 3 mm between contacts to section power supply.
• Connections inside the case made for protection circuit continuity are allowed as long as they include additional insulation
with respect to other internal drive parts.
• Install suitable tubes and ducts for electric cable passage to guarantee protection against mechanical damage.
Installation must be carried out by expert qualified personnel and in full observance of regulations in force.
5 Installation
5.2 Tools and materials
Make sure all tools and materials necessary are within reach to install the edge in maximum safety, according to regulations in
force. The following figure illustrates the minimum equipment for the installer.
N.B.: An evaluation of the size of the cables with lengths other than the data in the table must be made based on the effective
absorption of the connected devices, according to the instructions indicated by the CEI EN 60204-1 standards.
For connections that require several loads on the same line (sequential), the size given on the table must be re-evaluated based
on actual absorption and distances.
5.3 Cable list and minimun thickness
Connections Type of cable Length of cable 1 < 10 m Length of cable 10 < 20 m Length of cable 20 < 30 m
230V 2F power supply
FROR CEI
20-22
CEI EN
50267-2-1
3G x 1,5 mm 2 3G x 2,5 mm 2 3G x 4 mm 2
24V - 230V flashing lamp 2 x 0,5 mm 2 2 x 1 mm 2 2 x 1,5 mm 2
Photoelectric cells TX 2 x 0,5 mm 2 2 x 0.5 mm 2 2 x 0,5 mm 2
Photoelectric cells RX 4 x 0,5 mm 2 4 x 0,5 mm 2 4 x 0,5 mm 2
24V power supply accessory 2 x 0,5 mm 2 2 x 0,5 mm 2 2 x 1 mm 2
Control button 2 x 0,5 mm 2 2 x 0,5 mm 2 2 x 0,5 mm 2
Antenna connection RG58 max. 10 m
4
All the data and information contained herein is considered subject to change at any time and at our discretion
ENGLISH
Before proceeding with the installation, it is necessary to:
• Make sure the door is rigid and compact and that the sliding wheels are well oiled and in good condition.
• The ground guide must be well fastened to the ground, fully on the surface for the entirety of its length and without irregularities
that might obstruct the gate’s movement.
• The upper guide runners must not create friction.
• Provide for a gate stopper for opening and one for closing, and for the path of electrical cables as per standard system.
• Make sure the point in which the ratiomotor is fixed is in an area protected from shocks or bumps, and that the anchoring
surface is solid.
• Provide for suitable omnipolar disconnection device with more than 3 mm between contacts to section power supply.
• Connections inside the case made for protection circuit continuity are allowed as long as they include additional insulation
with respect to other internal drive parts.
• Install suitable tubes and ducts for electric cable passage to guarantee protection against mechanical damage.
Installation must be carried out by expert qualified personnel and in full observance of regulations in force.
5 Installation
5.2 Tools and materials
Make sure all tools and materials necessary are within reach to install the edge in maximum safety, according to regulations in
force. The following figure illustrates the minimum equipment for the installer.
N.B.: An evaluation of the size of the cables with lengths other than the data in the table must be made based on the effective
absorption of the connected devices, according to the instructions indicated by the CEI EN 60204-1 standards.
For connections that require several loads on the same line (sequential), the size given on the table must be re-evaluated based
on actual absorption and distances.
5.3 Cable list and minimun thickness
Connections Type of cable Length of cable 1 < 10 m Length of cable 10 < 20 m Length of cable 20 < 30 m
230V 2F power supply
FROR CEI
20-22
CEI EN
50267-2-1
3G x 1,5 mm 2 3G x 2,5 mm 2 3G x 4 mm 2
24V - 230V flashing lamp 2 x 0,5 mm 2 2 x 1 mm 2 2 x 1,5 mm 2
Photoelectric cells TX 2 x 0,5 mm 2 2 x 0.5 mm 2 2 x 0,5 mm 2
Photoelectric cells RX 4 x 0,5 mm 2 4 x 0,5 mm 2 4 x 0,5 mm 2
24V power supply accessory 2 x 0,5 mm 2 2 x 0,5 mm 2 2 x 1 mm 2
Control button 2 x 0,5 mm 2 2 x 0,5 mm 2 2 x 0,5 mm 2
Antenna connection RG58 max. 10 m
4
All the data and information contained herein is considered subject to change at any time and at our discretion
ENGLISH
5
6
7
8
9
10
11
12
13
14
15
16
17
18
advertisement
Related manuals
advertisement