Edison Professional M-2000 Plus Portable Bluetooth Speaker Operations Manual

Edison Professional M-2000 Plus Portable Bluetooth Speaker Operations Manual

Britelite M2000 is a professional, 2-way bi-amplified active speaker with a 15” long-throw woofer and a high-output compression driver. It delivers an even, smooth studio-quality sound. The speaker is suitable for home, studio, parties, and home theater use. It features ultra-wide, smooth dispersion of high and mid frequencies, a USB & SD card input that supports .wav & MP3 files, and Bluetooth compatibility. It also includes an FM radio with an antenna, a multi-function remote control, and is stand/pole-mountable for easy setup and transport.

advertisement

OPERATIONS MANUAL M2000
Professional ABS Molded Loudspeaker

Introduction:

Congratulations on your purchase of an M-2000 powered loudspeaker, engineered and
manufactured by BriteLite Enterprises. The M-2000 includes a high-output compression driver,
and 15” woofer to produce an even, smooth studio quality sound in a sound reinforcement
speaker. Our design goal was to build a speaker with accurate playback, smooth dispersion of
mid and high frequencies and an ergonomic design for easy transport and setup. The result is a
sound reinforcement system dynamic enough to use at home, in the studio, parties or in home
theater.

Features:

2-way Bi-amplified Active Speaker

15” Long-throw woofer with high-

temperature voice coil

Ultra-wide, smooth dispersion of

high and mid frequencies

Mic/Line input and pass-thru

connector

USB & SD Card input supports

.wav & MP3

Bluetooth Compatible

Includes FM Radio w/Antenna

Multi-function remote control

Stand/Pole-mountable

Cautions:

1. All Operating Instructions should be read before using this equipment.

2. To reduce the risk of electrical shock, do not open this unit. There are NO
REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician.

3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.

4. This unit should only be cleaned with a damp cloth. Avoid solvents or other cleaning
detergents.

5. When moving this equipment, it should be placed in its original carton and packaging.
This will reduce the risk of damage during transit.

6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR
SWITCHES

8. Make sure all of your equipment is completely OFF and lower ALL VOLUME, LEVEL &
GAIN controls before connecting a sound source.

9. Only LINE LEVEL SIGNALS SHOULD BE SENT TO YOUR SPEAKER.

Failing to adhere to the cautions above will void the manufacturer warranty!
OPERATIONS MANUAL M2000
Professional ABS Molded Loudspeaker

Functions:

1. USB Port

2. SD/MMC Port

3. LCD Display

4. Press this button to PAUSE. Press for 2-3 seconds to return to the
MENU

5. Press this button to return to the start of the previous track

6. Press this button to skip to the beginning of the next track.

7. Mode button, to switch between USB/SD or FM/Bluetooth function. Press
for two to three seconds to select EO/PLAY MODE/LANGUAGE. When
paused in USB/SD mode, press button for two or three seconds to select
a folder, then select the audio file.

8. Press to raise the Digital Audio Player’s volume. In folder mode, press to
skip to the previous page.

9. Press to lower the Digital Audio Player's volume. In folder mode, press to
skip to the previous page.

10. MIC IN: Use XLR or 1/4" jack connector balanced or unbalanced.

11. LINE IN: Use RCA or XLR connector balanced or unbalanced.

12. LINE OUT: Use this connector to daisy-chain several active speakers
together from the same signal source.

13. MIC LEVEL: Control the output volume when using a microphone.

14. LINE LEVEL: Control the output volume for LINE level inputs.

15. MASTER: Controls the output volume.

16. TREBLE: Raise or attenuate highs at 12dB @ 12 KHz frequency.

17. BASS: Raise or attenuate lows at 12dB @ 80Hz frequency.

18. PEAK: LED illuminates when a clipped signal is present. Reduce volume
to avoid distorted sound.

19. Power Indicator

20. Power Supply Switch

21. Voltage Selector: Adjust AC Power between 115V and 230V

22. Power Supply Input Connector: Use with power cord.

23. FM RADIO with antenna.

24. Remote Control

Warning:
Make sure speaker is off and all LEVEL controls are down (counterclockwise) before every
use.

Connections:

1.
Connect the output from your signal source (mixing console, microphone, preamp, or other mic- or
line
-level source) directly to the INPUT connector on the back of the speaker. It accepts balanced
line
-level signals from mixers, preamplifiers, CD players, tape decks, etc., and accepts direct
connections from dynamic microphones
through the MIC input.
2.
There is also a 1/4” and XLR Output connector labeled LINE OUT. This allows you to connect more
than one M
-2000 to the output of your sound source. Simply plug a ¼” or XLR cable from the Line
Out connector of one speaker to the input connector of another speaker, and so on, daisy
-chaining
multiple speakers.

3.
Turn on your signal source. (Make sure volume is turned down) Turn on M-2000. Start signal
source and adjust volume controls on the signal source and M
-2000 speaker.
OPERATIONS MANUAL M2000
Professional ABS Molded Loudspeaker

Bluetooth Connection

1. Make sure device (iPod, MP3 player, etc.) Bluetooth function is enabled. Remove SD Card or USB
stick from speaker before enabling Bluetooth.

2. On the speaker, press and hold menu (4) button for 2-3 seconds to call up main menu. Press
NEXT (6) button to select Bluetooth function and press MENU (4) button again to activate
Bluetooth. Your device and speaker should now be connected.

3. Make sure to choose BLUETOOTH from your device to complete the connection

4. Only one Bluetooth device can be connected to the M2000 speaker at a time.

5. To connect a new device; turn off the M2000 speaker for 10 seconds and turn on again and begin
with step one above.

Placement Tips

Avoid placing loudspeakers in the corners of a room. This increases the low-frequency output and can
cause the sound to be muddy and indistinct.

Avoid placing loudspeakers against a wall. This, too, increases the low frequency output, though not as
much as corner placement. However, if you do need to reinforce the low frequencies, this is a good way
to do it.

Avoid placing the active speakers directly on a hollow stage floor. A hollow stage can resonate at
certain frequencies, causing peaks and dips in the frequency response of the room. It’s better to place
the speakers on a sturdy table or tripod stands.

Position the speakers so the high-frequency drivers are two to four feet above ear level to the audience
to maintain high frequency quality.

Troubleshooting

No Power

First check to make sure the speaker is plugged in to a live AC outlet.

Make sure the POWER switch is on.

No Sound

Make sure input LEVEL control turned up.

Make sure signal source is working and the connecting cables are in good shape and securely
connected at both ends. Make sure the output volume control on the mixing console is turned up.

Make sure the preamp or mixer does not have a Mute button engaged.

Bad Sound Noise - Humming

If the sound is loud and distorted, verify that the levels are set properly on the speaker and mixing
console.

Make sure all connectors are secure and they are plugged in to the proper connecter (i.e., Mic cable
plugged in to MIC input, Line level source plugged in to Line Level Input.

It is a good idea to periodically clean all electrical connections with a non-lubricating electrical contact
cleaner.
OPERATIONS MANUAL M2000
Professional ABS Molded Loudspeaker

Make sure none of the signal cables are routed near AC cables, power transformers or other electrical
power cords.

If humming occurs, turn the LEVEL control of the speaker all the way down. If the noise disappears, it’s
coming from the signal source. If not, try disconnecting the cable connected to the INPUT jack. If the
noise disappears, it could be a “ground loop,” Try the following ideas:

o Use balanced connections throughout your system for best noise rejection. (XLR cables,
balanced ¼” jacks; RCA cables are not balanced)

o Whenever possible, plug all the audio equipment’s power cords into the same outlet.

o The hum may appear when using an unbalanced source (CD player, iPod, etc.). You
can use an RCA to XLR adapter to turn an unbalanced cable to a balanced cable.

o If the hum persists, try removing components one at a time from the back of the mixer
and check each for hum. Reducing the Bass or Treble levels (16 and 17) may reduce
humming.

Care and Maintenance

Your active speakers will provide many years of reliable service if you follow these guidelines:

Avoid exposing the loudspeaker to moisture. If they are set up outdoors, be sure they are under
cover if you expect rain.

Avoid exposure to extreme cold. If you must operate loudspeakers in a cold environment, warm
up the voice coils slowly by sending a low-level signal through them for about 15 minutes prior
to high-power operation.

Use a dry cloth to clean the cabinets. Only do this when the power is turned off. Avoid getting
moisture into any of the openings of the cabinet, particularly where the drivers are located.

Limited Warranty

This Limited Product Warranty is provided by BriteLite Enterprises. BriteLite warrants to
Customer that the product is free from defects in materials and workmanship under normal use
during the Warranty Period (the dealer that sold the speaker can provide the warranty period
information). If the product fails to conform to the warranty then BriteLite or its authorized
service will either repair or replace any nonconforming product, provided that Customer gives
notice of noncompliance within the Warranty Period to BriteLite by emailing
[email protected]
or calling 310-363-7110 (Mexico customers can call 0155 4624 0251). Please retain the original
dated receipt as evidence of proof of purchase.
  • Page 1
  • Page 2
  • Page 3
  • Page 4
/

advertisement

Key Features

  • 15" long-throw woofer with high-temperature voice coil
  • Ultra-wide, smooth dispersion of high and mid frequencies
  • 2-way bi-amplified design for powerful, clear sound
  • Mic/Line input and pass-thru connectivity
  • USB & SD Card input supports .wav & MP3 playback
  • Bluetooth connectivity for wireless audio streaming
  • Includes FM Radio w/Antenna
  • Multi-function remote control for convenient operation
  • Stand/Pole-mountable for flexible placement options

Questions & Answers

2024-10-17

C C L

How to contact BriteLite Enterprises customer service?
You can email [email protected] or call 310-363-7110. For Mexico customers, the number is 0155 4624 0251.

Related manuals

Frequently Answers and Questions

How do I connect my audio source to the M-2000 Plus?
You can connect your audio source to the M-2000 Plus using the XLR or 1/4" jack connectors for balanced or unbalanced line-level signals, or the RCA or XLR connectors for balanced or unbalanced line-level signals.
Can I daisy-chain multiple M-2000 Plus speakers together?
Yes, you can daisy-chain multiple M-2000 Plus speakers together using the 1/4" or XLR Output connector labeled LINE OUT.
How do I control the volume of the M-2000 Plus?
You can control the volume of the M-2000 Plus using the MASTER volume control on the back of the speaker.
Can I use the M-2000 Plus as a Bluetooth speaker?
Yes, you can use the M-2000 Plus as a Bluetooth speaker by enabling the Bluetooth function in the main menu.
What is the frequency response of the M-2000 Plus?
The frequency response of the M-2000 Plus is 50Hz-20kHz.

advertisement