Sony XSP-N1BT Installation guide

Sony XSP-N1BT Installation guide

Sony XSP-N1BT lets you connect your smartphone via Bluetooth, play music, and make hands-free calls while driving. It features a 4-channel amplifier with 45 watts per channel, a built-in microphone, and a wired remote control input. You can also connect an optional power amplifier or subwoofer to the RCA outputs. The unit also has a USB port for connecting a USB storage device, and an AUX input for connecting an external audio source. With its easy-to-use controls and a variety of connectivity options, the Sony XSP-N1BT is a great choice for upgrading your car's audio system.

advertisement

Cautions
Be sure to install this unit in the dashboard of the
car as the rear side of the unit becomes hot
during use.
ˎˎ This unit is designed for negative ground (earth) 12
V DC operation only.
ˎˎ Do not get the leads under a screw, or caught in
moving parts (e.g. seat railing).
ˎˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎˎ Connect the yellow and red power input leads
only after all other leads have been connected.
ˎˎ Run all ground (earth) leads to a common
ground (earth) point.
ˎˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
Notes on the power supply lead (yellow)
ˎˎ When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
ˎˎ When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts list ( )
ˎˎ The numbers in the list are keyed to those in the
instructions.
ˎˎ The bracket is attached to the unit before
shipping. Before mounting the unit, use the
release keys to remove the bracket from the
unit. For details, see “Removing the bracket ()”
on the reverse side of the sheet.
ˎˎ Keep the release keys for future use as they
are also necessary if you remove the unit from
your car.
* TOYOTA cars (India model) only. Used to close the gap between
the attachment.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Connection example ( )
Subwoofer Easy Connection (-B)
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
* Do not connect a speaker in this connection.
Notes
ˎˎ Be sure to connect the ground (earth) lead before connecting the
amplifier (-A).
ˎˎ The alarm will only sound if the built-in amplifier is used (-A).
ˎˎ Be sure to connect a 4 - 8 ohm subwoofer. Do not connect a
speaker to the other rear speaker cord (-B).
Connection diagram ( )
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow, and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
ˎˎ It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
ˎˎ When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply
leads.”
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a power antenna
(aerial). Connecting any other system may damage the unit.
To the +12 V power terminal which is energized
in the accessory position of the ignition switch
Notes
ˎˎ If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
ˎˎ When your car has a built-in FM/AM antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply
leads.”
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
ˎˎ REM OUT lead (blue/white striped) supplies +12 V DC when you
turn on the unit.
ˎˎ When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect REM OUT lead (blue/white striped) or the
accessory power supply lead (red) to the power terminal of the
existing antenna (aerial) booster. For details, consult your dealer.
ˎˎ A power antenna (aerial) without a relay box cannot be used with
this unit.
Memory hold connection
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
Notes on speaker connection
ˎˎ Before connecting the speakers, turn the unit off.
ˎˎ Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
ˎˎ Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the left
speaker.
ˎˎ Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
ˎˎ Do not attempt to connect the speakers in parallel.
ˎˎ Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the
unit.
ˎˎ To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–) lead
for the right and left speakers.
ˎˎ Do not connect the unit’s speaker leads to each other.
B
*
× 6

Equipment used in illustrations (not supplied)
Front speaker Subwoofer Power amplifier Rear speaker
REM OUT
Max. supply current 0.4 A
Fuse (10 A)
Blue/white striped
Red
Yellow
White
Green
Purple
White/black striped
Gray/black striped
Green/black striped
Gray
Left
Right
ACC
BATTERY
Black
Purple/black striped
*2
*2
*1
from car antenna (aerial)
Left
Right
*1 Speaker impedance: 4 – 8 ohms × 4
*2 RCA pin cord (not supplied).
* 3 Depending on the type of car, use an
adaptor for a wired remote control (not
supplied).
* 4 For details on installing the microphone,
see “Installing the microphone ()” on
the reverse side.
* 5 Whether in use or not, route the
microphone input cord such that it does
not interfere with driving. Secure the
cord with a clamp, etc., if it is installed
around your feet.

*4
A




× 2
*
XSP-N1BT
4-533-739-41(1)
©2014 Sony Corporation Printed in Thailand
Smartphone Cradle
Receiver
Installation/Connections GB
Installing the microphone ( )
To capture your voice during handsfree calling, you
need to install the microphone .
Cautions
ˎˎ Keep the microphone away from extremely high
temperatures and humidity.
ˎˎ It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from obstructing
your driving.
ˎˎ If airbags or any other shock-absorbing equipment
is in your car, contact the store where you
purchased this unit, or the car dealer, before
installation.
-A Installing on the sun visor
Install clips (not supplied) and adjust the length and
position of the cord so that it does not obstruct your
driving.
-B Installing on the dashboard
Install a clip (not supplied) and adjust the length and
position of the cord so that it does not obstruct your
driving.
Notes
ˎˎ Before attaching the double-sided tape , clean
the surface of the dashboard with a dry cloth.
ˎˎ Adjust the microphone angle to the proper
position.
Notes on the tuning step
ˎˎ For how to set the tuning step, see the supplied
Operating Instructions.
ˎˎ If replacing the car battery or changing the
connections, the tuning step setting will be erased.
-B Mounting the unit in a Japanese car
You may be able to install this unit in some makes of
Japanese cars without the supplied bracket. If you
cannot, consult your Sony dealer.
When mounting this unit to the preinstalled brackets
of your car, use the supplied screws in the
appropriate screw holes, based on your car: T for
TOYOTA, M for MITSUBISHI and N for NISSAN.
Note
To avoid a malfunction, install only with the supplied screws .
Warning if your car’s ignition
has no ACC position
Be sure to set the AUTO OFF function. For details, see
the supplied Operating Instructions.
The unit will shut off completely and automatically
in the set time after the unit is turned off, which
prevents battery drain.
If you do not set the AUTO OFF function, press and
hold OFF until the display disappears each time you
turn the ignition off.
Fuse replacement ( )
When replacing the fuse, be sure to use one
matching the amperage rating stated on the original
fuse. If the fuse blows, check the power connection
and replace the fuse. If the fuse blows again after
replacement, there may be an internal malfunction.
In such a case, consult your nearest Sony dealer.
Precautions
ˎˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
ˎˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperatures,
such as in direct sunlight or near heater ducts.
ˎˎ Use only the supplied mounting hardware for a
safe and secure installation.
ˎˎ To prevent hands or the shift lever touching the
unit or smartphone when operating the shift lever,
keep an adequate distance between the unit and
the shift lever.
Mounting angle adjustment
ˎˎ Mounting in a downward direction is not
supported.
ˎˎ Adjust the mounting angle to less than 45°.
Removing the bracket ( )
Before installing the unit, remove the bracket
from the unit.
1 Insert the release keys into the catches
between the unit and the bracket at the
same time until they click.
2 Pull down the bracket , then pull up the unit
to separate them.
Mounting the unit ( )
-A Mounting the unit with the
supplied bracket
1 Before installing, make sure that the catches on
both sides of the bracket are bent inwards
3.5 mm (5/32 in).
2 Position the supplied bracket inside the
dashboard.
3 Bend the claws outward for a tight fit.
4 Mount the unit onto the supplied bracket .
Note
If the catches are straight or bent outwards, the unit will not be
installed securely and may spring out.

B
A


Face the hook inwards.
B
Bracket
Bracket
to dashboard/center console

Existing parts supplied with your car
size
5 × max. 8 mm
( 7/32 × max. 5/ 16 in)
size
5 × max. 8 mm
(7/32 × max. 5 / 16 in)
Claws
Catch
Larger than 182 mm (7 1 /4 in)
Larger than 111 mm (4 3/8 in)
Fuse (10 A)
A
Clips (not supplied)
Clip (not supplied)
Location of screw holes
T: TOYOTA
M: MITSUBISHI
N: NISSAN
Catch
  • Page 1
  • Page 2
/

advertisement

Key Features

  • 4.0 channels Black
  • Built-in display Equalizer
  • MP3 playback USB direct playback
  • Bluetooth USB port

Related manuals

Frequently Answers and Questions

How do I install the microphone for handsfree calling?
You can install the microphone on the sun visor or dashboard. Follow the instructions provided in the Installation Guide.
What type of speakers can I use with the XSP-N1BT?
Use speakers with an impedance of 4 to 8 ohms and adequate power handling capacities to avoid damaging the unit.
What happens if the fuse blows?
Check the power connection and replace the fuse with one matching the amperage rating stated on the original fuse. If the fuse blows again, there may be an internal malfunction. Consult your nearest Sony dealer.

advertisement