Fusion CS-AT1100 User's Manual

Show PDF Add to My manuals
2 Pages

advertisement

ACTIVE TUBE
SPECIFICATIONS

CS-AT1100

Peak Power (Watts)
360
Rated Power (Watts)
120
Frequency Response
36Hz - 250Hz
Low Pass Filter (Variable)
40Hz - 250Hz
Tuning
Bass Reflex
Woofer Size
10”
Fuse
20A
Dimensions (mm)
559(l) x 306(w) x 306(h)
22-1/32 x 12-1/16 x 12-1/16”

CS-AT1100

www.fusionelectronics.com

CONTROL DESCRIPTIONS

LEVEL

This allows the adjustment of the amplifier level of the subwoofer.

Turn clockwise to increase the level. If the sound becomes distorted

reduce the level.

LOW
PASS FILTER (LPF)
This allows the adjustment of the highest frequency the Active

Tube will produce. This should be adjusted to blend with your main

speakers. Typically, this will be set to around 100Hz (approximately

the central position of the control knob).

REMOTE
LEVEL CONTROLLER
When connected, this allows further control over the level from a

remote location, using the supplied lead.

INSTALLATION

Make sure the Active Tube is firmly fixed in your vehicle. Check

before drilling or cutting holes. DO NOT work near gas tanks, fuel

lines, hydraulic lines or electrical wiring.

DO
NOT mount the Active Tube in such a way as to pinch or damage
the wires.

Make
sure everything is firmly connected, before attaching the
+12V wire. Ensure the +12V wire is fused as close as possible to the

battery. Always use a fuse with the recommended rating.

DISCLAIMER

Always ensure the Active Tube is securely attached, to avoid movement. FUSION accepts no responsibility for damage or injury in relation

to inappropriate securing of this product.

WIRING

• Connect the ground wire to the vehicle first (clean dirt and paint

to bare metal).

• Connect the remote on (blue wire).

• Connect the RCA cables if applicable, OR

• Connect the speaker level wire by splicing into the headunits

speaker wires. See
Note 1 on reverse.
• Connect the remote level controller with the supplied lead.

• Connect the 12 volt (red wire) to the positive battery terminal.

• Check all connections.
PUBLISHED BY FUSION ELECTRONICS LIMITED: © Copyright 2010 by FUSION Electronics Limited. All rights reserved. Specifications and design are subject to change without notice.
YOU CAN HELP PROTECT THE ENVIRONMENT! Please remember to respect the local regulations: Hand in the non-working electrical equipment to an appropriate waste disposal center.

RECORD YOUR PURCHASE DETAILS HERE:

SERIAL NUMBER

DATE OF PURCHASE

AFFIX RECEIPT HERE

WARNING:
Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE!

For further product and installation information, please visit www.fusionelectronics.com

Pour plus d’informations sur les produits et l’installation, rendez-vous sur www.fusionelectronics.com

Para obtener más información acerca de los productos y de su instalación, visite el sitio web www.fusionelectronics.com

Bezoek www.fusionelectronics.com voor meer product- en installatie-informatie.

Weitere Produkt- und Installationsinformationen finden Sie unter www.fusionelectronics.com

Per ulteriori informazioni sui prodotti e la loro installazione, potete visitare www.fusionelectronics.com

Для получения дополнительной информации о продуктах и установке зайдите, пожалуйста, на: www.fusionelectronics.com

Note 1

Take care to make sure the wires

are spliced in the correct phase.

Positive to positive, negative to

negative. Failure to do this correctly

could result in loss of bass.

See
Note 1
Splice into source

unit’s speaker wires

(R+) Grey/White

(R- ) Grey

(L+) Green/White

(L-) Green

Connect the remote

level controller lead to

the amplifier

Connect red wire

to positive (+12V)

battery terminal

Connect blue wire to source unit’s

accessory lead or switched 12 volt

source (REM)

Connect black wire

to chassis ground

of vehicle (Ground)

Speaker Level

Input Plug

Remote Level Controller

Vehicle Battery
  • Page 1
  • Page 2
/

advertisement

Key Features

  • 360-watt peak power and 120-watt RMS power for deep, impactful bass
  • 10" woofer and bass reflex tuning for accurate and extended low-frequency response
  • Variable low-pass filter to customize the subwoofer's output
  • Remote level controller for convenient control from the driving seat
  • Compact design for easy installation in a variety of vehicles
  • High-level and low-level inputs for compatibility with a wide range of head units
  • Automatic turn-on/off feature for seamless integration with your system

Related manuals

Frequently Answers and Questions

What is the frequency response of the Fusion CS-AT1100?
The frequency response of the Fusion CS-AT1100 is 36Hz - 250Hz.
Can I adjust the level of the subwoofer from my driving seat?
Yes, the Fusion CS-AT1100 comes with a remote level controller that allows you to adjust the subwoofer's output level from the comfort of your driving seat.
What is the size of the woofer in the Fusion CS-AT1100?
The Fusion CS-AT1100 features a 10" woofer.
How do I connect the Fusion CS-AT1100 to my car audio system?
The Fusion CS-AT1100 can be connected to your car audio system using either high-level or low-level inputs.
Does the Fusion CS-AT1100 have an automatic turn-on/off feature?
Yes, the Fusion CS-AT1100 has an automatic turn-on/off feature that seamlessly integrates with your system.

advertisement