Drill Master 61691 3-1/4 in. 5.5 Amp Electric Planer Owner's Manual

Show PDF Add to My manuals
20 Pages

advertisement

Page 2 For technical questions, please call 1-800-444-3353. Item 61691
SAFETy OpERATION MAINTENANcESETUp
Table of contents
Safety ......................................................... 2
Specifications ............................................. 8
Setup .......................................................... 8
Operation .................................................... 9
Maintenance .............................................. 14
Parts List and Diagram .............................. 18
Warranty .................................................... 20
WARNING SyMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMpORTANT SAFETy INFORMATION
General power Tool Safety Warnings
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool.
Work Area Safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
Page 3For technical questions, please call 1-800-444-3353.Item 61691
SAFETyOpERATIONMAINTENANcE SETUp
Electrical Safety
1. power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
2. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a Ground Fault circuit
Interrupter (GFcI) protected supply.
Use of a GFCI reduces the risk of electric shock.
personal Safety
1. Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power
tool while you are tired or under the
influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
2. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
3. prevent unintentional starting.
Ensure the Trigger is in the off-position before
connecting to power source, picking up or
carrying the tool.
Carrying power tools with your finger on
the Trigger or energizing power tools that
have the Trigger on invites accidents.
4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust‑related hazards.
8. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must be
ANSI-approved and breathing protection
must be NIOSH-approved for the
specific hazards in the work area.
power Tool Use and care
1. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the power tool if the Trigger
does not turn it on and off.
Any power tool that cannot be controlled with the
Trigger is dangerous and must be repaired.
3. Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Page 4 For technical questions, please call 1-800-444-3353. Item 61691
SAFETy OpERATION MAINTENANcESETUp
5. Maintain power tools. check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
planer Safety Warnings
1. Wait for the cutter to stop before setting
the tool down. An exposed rotating cutter
may engage the surface leading to possible
loss of control and serious injury.
2. Hold the power tool by insulated gripping
surfaces only, because the cutter may contact
its own cord. Cutting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
3. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
4. Before every use, confirm that both knives are
properly aligned and both knives are secured fully.
Then, start tool off of workpiece and
allow tool to reach full speed.
If tool vibrates or becomes noisy
SWITcH IT OFF IMMEDIATELy,
unplug it and allow it to come to a complete stop.
Adjust and tighten knives to correct imbalance.
If vibration or noise persists, do not use tool until
inspected and repaired by a qualified technician.
5. Remove all foreign objects, such as nails or metal
fragments, from the workpiece before planing.
6. Do not use to plane non-wood materials.
7. Knives are very sharp and are double-edged!
Wear heavy-duty leather work gloves at all times
when replacing, adjusting, or handling a knife.
8. Change both knives at once. Changing knives
individually could result in imbalance.
9. Do not unclog dust chute with
tool plugged in or blades moving.
Do not insert your finger into the dust chute.
10. Connect dust chute to bag or dust collection system
(not included) before use. Do not use without
a dust bag or dust collection system.
11. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
12. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
13. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
14. When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.
15. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.
16. This product is not a toy.
Keep it out of reach of children.
17. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with Trigger locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
  • Page 1
  • Page 2
  • Page 3
  • Page 4
  • Page 5
  • Page 6
  • Page 7
  • Page 8
  • Page 9
  • Page 10
  • Page 11
  • Page 12
  • Page 13
  • Page 14
  • Page 15
  • Page 16
  • Page 17
  • Page 18
  • Page 19
  • Page 20
/

advertisement

Key Features

  • Variable speed trigger for precise control
  • Keyless chuck for easy bit changes
  • Compact and lightweight design for easy handling
  • Ergonomic grip for舒适操作
  • Safety features to protect users from injury
  • Durable construction for long-lasting performance

Related manuals

Frequently Answers and Questions

What safety precautions should be taken when using the Drill Master (Item 61691)?
Always wear eye protection, ensure the Trigger is off before plugging in the tool, and keep the cord away from heat, oil, sharp edges, and moving parts. Use a Ground Fault Circuit Interrupter (GFCI) when operating outdoors or in damp locations.
How should I handle the dust chute?
Connect the dust chute to a bag or dust collection system before use, and never unclog the dust chute while the tool is plugged in or the blades are moving.
What should I do if the tool starts vibrating or making noise?
Immediately switch off the tool, unplug it, and allow it to stop completely. Adjust and tighten the knives to correct the imbalance. If the vibration or noise persists, do not use the tool until it has been inspected and repaired by a qualified technician.
How often should the knives be changed?
Change both knives at once, as changing them individually could result in imbalance.
What should I do before starting to use the tool?
Prepare your workspace, ensure the knives are properly aligned and secured, and connect the dust chute to a bag or dust collection system.

advertisement