Daytona 64051 Steel Floor Jack Cross Beam Owner's Manual

Show PDF Add to My manuals
4 Pages

advertisement

Floor jack sold separately.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected] 64051
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 19g
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2017 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 64051
Specifications
Rated Capacity 4,000 lb.
IMPORTANT SAFETY INFORMATION
1. Study, understand, and follow all instructions
before operating this device.
2. Do not exceed 4,000 lb. rated capacity.
3. Ensure load is secured to the device.
4. To be used only with the following PASE (Portable
Automotive Service Equipment): Daytona™ floor
jacks and Pittsburgh Automobile ® floor jacks, except
trolley-style jacks including, but not limited to,
(68783, 69306, 69468, 62117). Do not use this Cross
Beam on any jack that the Connection Bolt does
not attach to securely and tighten to completely.
5. No alterations shall be made to this product.
6. Center load over floor Jack’s saddle.
7. Adjust pads to keep bar level during lifting.
8. Only use with included safety chains properly
connected to prevent overextension.
9. Install and use aligned perpendicular
to floor jack body only.
10. Also, study, understand, and follow all floor jack
instructions before operating this device.
11. Wear ANSI-approved safety goggles and
heavy-duty work gloves during use.
12. Do not move or dolly the vehicle
while on the cross beam.
13. Use as intended only.
Do not use for lifting human weight. Keep clear
of raised load. Do not use for aircraft purposes.
14. Lift vehicle only at
manufacturer-recommended locations.
15. Inspect before every use;
do not use if parts loose or damaged.
16. Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Remove Saddle Connection Bolt and Saddle
from floor Jack (sold separately).
2. Place Cross Beam on floor Jack.
3. For 3T low profile and 3T long reach Daytona
or Pittsburgh jacks, do not use the Spacer
on the Connection Bolt. For all other 3T and
4T Daytona or Pittsburgh jacks, slide Spacer
onto Connection Bolt before installing it.
4. Install Cross Beam’s Connection Bolt and
tighten it securely in place while keeping Cross Beam
aligned perpendicular to floor Jack body.
Page 3For technical questions, please call 1-888-866-5797.Item 64051
Operation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Lower both Saddle Pads completely.
2. Align each Saddle Pad under a vehicle lifting point.
Center the vehicle’s weight over the floor Jack.
WARNING! Lift vehicle only at
manufacturer-recommended locations.
WARNING! Make sure Cross Beam
is at 90° to the floor Jack.
3. Use floor Jack to raise Cross Beam until
one of the Saddle Pads is about to contact
one of the vehicle lifting points.
4. Turn the Saddle Pads to adjust each one
until they both contact the lifting points.
5. Stay clear of vehicle, Jack and Cross Beam
while slowly raising the vehicle until
it is at the desired height.
WARNING! While lifting, make sure
that the Cross Beam remains level and
the load is centered over the floor Jack.
6. Place two Jack Stands at manufacturer-
recommended support points and adjust until
they almost contact each support point.
7. Stay clear while lowering the vehicle onto the
Jack Stands. Lower the vehicle’s weight completely
onto Jack Stands before working under it.
Parts List and Diagram
Part Description Qty
1 Beam 1
2 Extension Tube 2
3 Saddle 2
4 Rubber Pad 2
5 Screw 8
6 Chain Washer 2
Part Description Qty
7 Flat Washer 2
8 Lock Washer 2
9 Bolt 2
10 Connection Bolt 1
11 Spacer 1
10
11
1
8
9
5
4
3
2
6
7
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown for
illustration purposes only, and are not available
individually as replacement parts.
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
  • Page 1
  • Page 2
  • Page 3
  • Page 4
/

advertisement

Key Features

  • 4,000 lb. rated capacity
  • Adjustable saddle pads
  • Included safety chains
  • Compatible with Daytona™ and Pittsburgh Automobile® floor jacks
  • Provides added stability and support
  • Easy to install and use

Related manuals

Frequently Answers and Questions

What is the rated capacity of the Daytona 64051 cross beam?
4,000 lbs.
Can I use the Daytona 64051 cross beam with any floor jack?
No, it is only compatible with Daytona™ and Pittsburgh Automobile® floor jacks.
How do I install the Daytona 64051 cross beam?
Remove the saddle connection bolt and saddle from the floor jack. Place the cross beam on the floor jack. Install the cross beam's connection bolt and tighten it securely in place while keeping the cross beam aligned perpendicular to the floor jack body.
How do I use the Daytona 64051 cross beam?
Lower both saddle pads completely. Align each saddle pad under a vehicle lifting point. Center the vehicle's weight over the floor jack. Use the floor jack to raise the cross beam until one of the saddle pads is about to contact one of the vehicle lifting points. Turn the saddle pads to adjust each one until they both contact the lifting points. Stay clear of the vehicle, jack, and cross beam while slowly raising the vehicle until it is at the desired height. Place two jack stands at manufacturer-recommended support points and adjust until they almost contact each support point. Stay clear while lowering the vehicle onto the jack stands. Lower the vehicle's weight completely onto the jack stands before working under it.

advertisement