Ohlins 35000-03 Ducati Multistrada 1200 S Suspension Control Unit Mounting Instruction

Show PDF Add to My manuals
4 Pages

advertisement

Ducati Multistrada 1200S Suspension Control Unit
35000-03
Mounting Instructions and Set-up Guide
Note!
Before installing this product, check the contents
of the kit. If anything is missing, please contact an
Öhlins dealer.
Note!
This product is only applicable for Ducati Multistrada
1200S 2010-2012.
Warning!
Before installing this product, read this document
thouroughly. If you have any questions please contact
an Öhlins dealer.
Kit Contents
Description Part No Pcs
SCU 35000-03 1
Sticker Mechatronic S 00191-46 2
2/4
1
Put the motorcycle on a stand.
2
Remove the seat.
3
Disconnect the negative battery terminal.
4
Remove the plastic side fairing on the left side
of the seat.
5
Locate the original suspension control unit in
the rubber mount. Disconnect the connector
and remove the original suspension control
unit from the rubber mount.
M
oUNtING INStrUCtIoNS
Warning!
It is advisable to have an Öhlins dealer install the SCU.
Warning!
If working on a raised vehicle, ensure it is securely
supported so that it will not tip.
Note!
Before mounting this product clean the vehicle
thoroughly.
Note!
When working on this product, always see the Vehicle
Service Manual for vehicle specific procedures and
important data.
6
Insert the SCU (35000-03) in the rubber
mount and connect the connector. Make sure
it connects properly. You should hear a notice-
able click.
Warning!Ensure to connect the connector properly. You should
hear a noticeable click. If you have any questions
regarding proper installation, please contact an Öhlins
dealer.
7
Reinstall the plastic side fairing.
8
Reconnect the negative battery terminal.
9
Reinstall the seat.
10
Turn on the ignition and the electronic preload
adjuster will calibrate at the first start-up.
11
Go to User Interface for further information.
3/4
US
er INterfaCe
How to operate
The Öhlins SCU (35000-03) is operated in the
same way as the original SCU, by the menu
buttons on the left handlebar. See the vehicle
manual for menu description.
a
ctivate event Based Control
The Event Based Control is a feature that
changes suspension setting while riding.
t
o activate event Based Control
Enter the suspension settings menu in the
dashboard. Set according to the following:
Front compression 1
Front rebound 1
Rear compression 1
Rear rebound 1
Note!
When Event Based Control is desired, the suspension
setting must be set according to the table above.
e
ngine mode
When Event Based Control is enabled the
function depends on the engine mode select-
ed in the set up.
100hp Comfort mode adjusts the damp-
ing with vehicle speed to optimize
comfort while maintaining enough
stability.
► Default engine mode in URBAN
and ENDURO set up.
150hp
low
t
ouring mode adjusts the damp-
ing for best combination of agility
and comfort.
► Default engine mode in
TOURING set up.
150hp
high
Sport mode adjusts the damping
during acceleration and braking to
optimize sport performance.
► Default engine mode in SPORT
set up.
A suspension mode is the combination of
set up (SPORT, TOURING, URBAN and
ENDURO) and the load selection (rider, rider
with luggage, two riders and two riders with
luggage). This gives a total of 16 suspension
modes.Example
Riding mode; SPORT and “rider only”. If
(1,1,1,1) is set the Event Based Control is
only enabled at this suspension mode and
load selection. All other modes are working
with their individual damping set-up.
r
ear preload set up
Adjust in the preload menu on the dashboard.
Suspension settings menu Engine mode
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.To find the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
Set-UP Data
Part no. MI_35000-03_0
Issued 2013-04-26
f
ront fork Setting translation table
The adjustment range is wider for the Öhlins
SCU which enables a softer setting position at
position 32 than for the original SCU. To keep
your fixed setting see the translation table
below.
a
djustment range
Shock absorber: (same as original)
Front fork :
Öhlins SCU
f
ront fork setting
o
riginal SCU
f
ront fork setting
1 1
3 4
5 8
7 12
10 18
12 22
14 26
17 32
18-32 New! -
Note!
Please note that when using this SCU your settings
in the front fork will be softer. See the translation
table above.
  • Page 1
  • Page 2
  • Page 3
  • Page 4
/

advertisement

Key Features

  • Event Based Control for automatic suspension adjustment
  • Wider front fork adjustment range for softer settings
  • Adjustable rear preload for load optimization
  • Easy-to-use menu interface for suspension settings
  • Compatibility with Ducati Multistrada 1200S 2010-2012

Related manuals

Frequently Answers and Questions

How do I activate Event Based Control?
Enter the suspension settings menu and set the following: Front compression 1, Front rebound 1, Rear compression 1, Rear rebound 1.
How do I adjust the rear preload?
Adjust in the preload menu on the dashboard.
What is the adjustment range for the front fork?
1-32 for Öhlins SCU, compared to 1-22 for the original SCU.

advertisement