7000 Drypix Service Manual
Drypix 7000 is a device that allows you to remove and adjust different parts. It has a variety of features, including a tray loading unit, a removal unit, a conveyor unit, a sub-scanning unit, a scanning optics unit, a heat development unit, a film release unit, a controller, a sorter, and a version upgrade and full installation of the main unit software. It also has board setting and LED lighting information.
advertisement
DRYPIX 7000
SERVICE MANUAL
REMOVAL AND ADJUSTMENT (MC)
SERVICE MANUAL
REMOVAL AND ADJUSTMENT (MC)
MC-1
006-259-02
04.01.2003 FM3978 MC-1DRYPIX 7000
Service Manual
CONTROL SHEET
Revision Number Reason Pages AffectedIssue Date
10/15/2002 00 New release (FM3343) All pages
11/10/2002 01 Revised (FM3601) 1, 3-11, 13-17, 20, 22, 23, 26, 27,
33-39, 44, 46-149
04/01/2003 02 Revised (FM3978) 1, 10, 11, 15, 16, 22, 23, 28, 31, 35,
37, 44, 54-57, 60, 75-77, 90-94,
107-109, 118, 120, 135, 141-149
006-259-02
04.01.2003 FM3978 MC-1DRYPIX 7000
Service Manual
CONTROL SHEET
Revision Number Reason Pages AffectedIssue Date
10/15/2002 00 New release (FM3343) All pages
11/10/2002 01 Revised (FM3601) 1, 3-11, 13-17, 20, 22, 23, 26, 27,
33-39, 44, 46-149
04/01/2003 02 Revised (FM3978) 1, 10, 11, 15, 16, 22, 23, 28, 31, 35,
37, 44, 54-57, 60, 75-77, 90-94,
107-109, 118, 120, 135, 141-149
MC-2
006-259-00
10.15.2002 FM3343 MC-2DRYPIX 7000
Service Manual
PRECAUTIONS ON INSPECTIONS, REPLACEMENTS,
AND ADJUSTMENTS
This chapter does not describe parts which require no special note or adjustments in
removal and installation.
For details on the removal of these parts, refer to the Parts List.
Also follow the precautions below when performing inspections, replacements, and
adjustments of parts.
WARNING
To prevent electrical shocks, be sure to turn OFF the power of this equipment
before starting work.
WARNING/CAUTION
Observe the warnings and cautions described in “SAFETY PRECAUTION”.
CAUTION
Be sure to wear a wristband for grounding when performing maintenance of boards and
optical units. Otherwise static electricity in the body may cause damage to electronic
parts on the boards and optical units.
CAUTION
Never remove the screws painted in red.
<INSTRUCTIONS>
The screws painted in yellow must be adjusted after the installation of parts.
When installing parts, follow the check/adjustment procedure provided.
<NOTE>
When removing the covers, insert shutter into the film tray to prevent exposure of film to light.
006-259-00
10.15.2002 FM3343 MC-2DRYPIX 7000
Service Manual
PRECAUTIONS ON INSPECTIONS, REPLACEMENTS,
AND ADJUSTMENTS
This chapter does not describe parts which require no special note or adjustments in
removal and installation.
For details on the removal of these parts, refer to the Parts List.
Also follow the precautions below when performing inspections, replacements, and
adjustments of parts.
WARNING
To prevent electrical shocks, be sure to turn OFF the power of this equipment
before starting work.
WARNING/CAUTION
Observe the warnings and cautions described in “SAFETY PRECAUTION”.
CAUTION
Be sure to wear a wristband for grounding when performing maintenance of boards and
optical units. Otherwise static electricity in the body may cause damage to electronic
parts on the boards and optical units.
CAUTION
Never remove the screws painted in red.
<INSTRUCTIONS>
The screws painted in yellow must be adjusted after the installation of parts.
When installing parts, follow the check/adjustment procedure provided.
<NOTE>
When removing the covers, insert shutter into the film tray to prevent exposure of film to light.
MC-3
006-259-01
11.10.2002 FM3601 MC-3DRYPIX 7000
Service Manual
The diagrams in this manual displays the CHECK and FIT ON icons where necessary.
When removing/reinstalling, following these icons.
• CHECK icon: When reinstalling removed parts, this is indicated if reinstalling
positions must be checked or adjusted.
This symbol is shown inside illustrations of parts removal
procedures. Whenever this is shown, be sure to refer to "n CHECK/
Adjusting procedure".
• FIT ON icon: When installing parts, this is indicated if alignment to the boss is
required.
CHECK
006-259-01
11.10.2002 FM3601 MC-3DRYPIX 7000
Service Manual
The diagrams in this manual displays the CHECK and FIT ON icons where necessary.
When removing/reinstalling, following these icons.
• CHECK icon: When reinstalling removed parts, this is indicated if reinstalling
positions must be checked or adjusted.
This symbol is shown inside illustrations of parts removal
procedures. Whenever this is shown, be sure to refer to "n CHECK/
Adjusting procedure".
• FIT ON icon: When installing parts, this is indicated if alignment to the boss is
required.
CHECK
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
advertisement
Key Features
- Removal and adjustment of parts
- Tray loading unit
- Removal unit
- Conveyor unit
- Sub-scanning unit
- Scanning optics unit
- Heat development unit
- Film release unit
- Controller
- Sorter
Related manuals
Frequently Answers and Questions
What are the precautions to take when performing inspections, replacements, and adjustments of parts?
The manual recommends turning OFF the power of the equipment before starting work to prevent electrical shocks. It also advises wearing a wristband for grounding when performing maintenance of boards and optical units to prevent static electricity damage. Additionally, it cautions against removing screws painted in red and advises adjusting screws painted in yellow after the installation of parts. Finally, it reminds users to insert a shutter into the film tray when removing the covers to prevent film exposure to light.
How do I read the removal and adjustment volume?
The removal and adjustment volume is constructed so that it can be referred to together with the service parts list volume. The chapter number in the removal and adjustment volume is related to the index number in the service parts list volume. The section number in the removal and adjustment volume indicates the enclosed reference number in the service parts list volume's exploded view.
What are the different parts that can be removed and adjusted?
The manual lists various parts that can be removed and adjusted, including covers, the frame, the tray loading unit, the removal unit, the conveyor unit, the sub-scanning unit, the scanning optics unit, the heat development unit, the film release unit, the controller, the sorter, and the main unit software.
How do I change the film size of the tray?
To change the film size from 35 x 43 cm to 20 x 25 cm, you need to remove the removal unit, replace the suction cup arm with the 20 x 25 cm size suction cup arm, change the attaching position of the film release plate, change the attaching position of the barcode reader, and reinstall the removed parts in the reversed order of the removal procedure.
How do I adjust the sub-scanning unit positioning screw?
You can adjust the sub-scanning unit positioning screw by printing the grid pattern, measuring the D and E on the printed film, and checking that they meet the specified values. If the measured values are not the specified values, you need to loosen the screws securing the sub-scanning unit, remove the sub-scanning unit fixing bracket, reinstall the sub-scanning unit fixing bracket at the specified position and rotate the positioning screw in the clockwise or counterclockwise direction to make adjustments.
advertisement
