RICH DP 525 Dimensional Control Unit OPERATION INSTRUCTIONS/USER MANUAL
The DP 525 is a micro-computer controlled dimension clamping unit designed for use in industrial applications. Featuring a user-friendly interface, it allows for precise dimension setting and control. With the ability to display dimension units in mm, INCH, or 尺, the DP 525 offers versatile measurement capabilities. It includes features like parameter calculation and setting, magnification setting, and manual and automatic start operating modes.
advertisement
DP 525
OPERATION INSTRUCTIONS/USER MANUAL
OPERATION INSTRUCTIONS/USER MANUAL
CONTENTS
1.SPECICICATIONS.................................................1
2.CHARACTERISTICS.............................................1
3.PANEL DISPLAY AND DESCRIPTION OF
BUTTON FUNCTIONS..........................................1
4.DESCRIPTION OF RELAY FUNCTION .............2
5.OPERATING INSTRUCTION FOR CORRECTING
EXISTING DATA...................................................2
6.DESCRIPTION OF SETTING 10th DIGIT............3
7.DIMENSIKON UNIT SELECTING AND
DESCRIPTION OF CHANGE...............................4
8.DESCRIPTION OF MANUAL
OPERATING (+),(-)................................................5
9.DESCRIPTION OF AUTOMATIC START
OPERATING...........................................................5
10.DESCRITPTION OF PARAMETER
CALCULATION AND SETTING........................6
11.DESCRIPTION OF MAGNIFICATION
SETTING...............................................................7
12.FAULT SITUATION AND TROUBLE-
SHOOTING...........................................................8
1.SPECICICATIONS.................................................1
2.CHARACTERISTICS.............................................1
3.PANEL DISPLAY AND DESCRIPTION OF
BUTTON FUNCTIONS..........................................1
4.DESCRIPTION OF RELAY FUNCTION .............2
5.OPERATING INSTRUCTION FOR CORRECTING
EXISTING DATA...................................................2
6.DESCRIPTION OF SETTING 10th DIGIT............3
7.DIMENSIKON UNIT SELECTING AND
DESCRIPTION OF CHANGE...............................4
8.DESCRIPTION OF MANUAL
OPERATING (+),(-)................................................5
9.DESCRIPTION OF AUTOMATIC START
OPERATING...........................................................5
10.DESCRITPTION OF PARAMETER
CALCULATION AND SETTING........................6
11.DESCRIPTION OF MAGNIFICATION
SETTING...............................................................7
12.FAULT SITUATION AND TROUBLE-
SHOOTING...........................................................8
20%+AC(0V-110V-220V)50/60HZInput:1.Power
2.Signal Input:StandardENCODERABPhaseSignal(DC12V).
3.TheWithstandingPressureofTheOutPutPanelPointOfTheRelay:AC(250V-3A).
4.SafetyLimitSwitch:Whenusingthiscontrolunit,thestrokesafetylimitswitchmustbeadopted.Please
useNC,Cintheelectromagnetismon-offreturncircuittoprotectautomatically,orcascadewiththerelay
R1,R2ofthiscontrolunit.(SeriousWarning)Tomakesurethesafetyofpeopleandmachineryoperation,
the safety limitswitchmust beequipped.
5.Theelectricians andoperatorshave topaytheirattentionnottomakeanychangepersonallyontheabove
mentioned4points(without theagreementofourtechnicians)otherwise,thecontrolunitis possibletobe
ensurethesafetyofpeople,pleasecaution.
1.SPECIFICATIONS Please obey this regulation !
2.CHARACTERISTICS
1.TheMicro-ComputerSingleChipis adoptedinthismachine.The
stability and safetycanbeassuredunderlongtimetunning.
2.Eventhoughthepowervoltage isdifferentorthedriveconstructionis
wornoutdaybydayandthechangeofreturncircuitcaneffect
completely thefunctionofdimensionclamping.
3.TheParameterofthismachinecanbeset.
4.TheMagnificationcanbeset.
5.Thismachinecandisplay3differentunits ofdimensions,mm,INCH,
and canbetransitedimmediately.
6.ThethicknessDatacanbeset.
7.ThefiguresunderDecimalPointcanbe setseparately.
3.PANEL DISPLAY AND DESCRIPTION OF
BUTTON FUNCTIONS
figurebuttons
6,7,8,9,are
0,1,2,3,4,5
forclear
ButtonC
button
Point
Decimal
buttons
arefunction
,START,STOP
SET,UNIT,-,+
Panel
DataDisplay
1.Figurebuttonarefrom0to9
2.ButtonCisforclear.
3..isabuttonforsettingthedigitsatrightsideofDecimal
Point.
4.SET is a buttonforsettingdata.
5.UNITisbuttonfortransitingdimensionunits.
6.-isformanualoperationtoincreasethefigure.
7.+isfor manual operationtoincreasethefigure.
8.START isbuttontostart.
9.STOPisabuttontostopandstopalloperations
meanwhile.
2.Signal Input:StandardENCODERABPhaseSignal(DC12V).
3.TheWithstandingPressureofTheOutPutPanelPointOfTheRelay:AC(250V-3A).
4.SafetyLimitSwitch:Whenusingthiscontrolunit,thestrokesafetylimitswitchmustbeadopted.Please
useNC,Cintheelectromagnetismon-offreturncircuittoprotectautomatically,orcascadewiththerelay
R1,R2ofthiscontrolunit.(SeriousWarning)Tomakesurethesafetyofpeopleandmachineryoperation,
the safety limitswitchmust beequipped.
5.Theelectricians andoperatorshave topaytheirattentionnottomakeanychangepersonallyontheabove
mentioned4points(without theagreementofourtechnicians)otherwise,thecontrolunitis possibletobe
ensurethesafetyofpeople,pleasecaution.
1.SPECIFICATIONS Please obey this regulation !
2.CHARACTERISTICS
1.TheMicro-ComputerSingleChipis adoptedinthismachine.The
stability and safetycanbeassuredunderlongtimetunning.
2.Eventhoughthepowervoltage isdifferentorthedriveconstructionis
wornoutdaybydayandthechangeofreturncircuitcaneffect
completely thefunctionofdimensionclamping.
3.TheParameterofthismachinecanbeset.
4.TheMagnificationcanbeset.
5.Thismachinecandisplay3differentunits ofdimensions,mm,INCH,
and canbetransitedimmediately.
6.ThethicknessDatacanbeset.
7.ThefiguresunderDecimalPointcanbe setseparately.
3.PANEL DISPLAY AND DESCRIPTION OF
BUTTON FUNCTIONS
figurebuttons
6,7,8,9,are
0,1,2,3,4,5
forclear
ButtonC
button
Point
Decimal
buttons
arefunction
,START,STOP
SET,UNIT,-,+
Panel
DataDisplay
1.Figurebuttonarefrom0to9
2.ButtonCisforclear.
3..isabuttonforsettingthedigitsatrightsideofDecimal
Point.
4.SET is a buttonforsettingdata.
5.UNITisbuttonfortransitingdimensionunits.
6.-isformanualoperationtoincreasethefigure.
7.+isfor manual operationtoincreasethefigure.
8.START isbuttontostart.
9.STOPisabuttontostopandstopalloperations
meanwhile.
Diagram 3
4.DESCROPTION OF RELAY FUNCTION
5.Operating Instruction For Correcting Data
1.In accordancewiththedimensionofthe actual material,press(SET)buttonand(0.)willshownonthe
display.Usecorrectfigures andpress (0 to9)buttons,thenpressbutton(SET)for2-3seconds.Thedisplay
will starttoflashandthenstopflashing.Finallythe figuresinput formerlywill beshownandcomplete
correctingdata.Ifthetimeforpressingthebutton(SET)orinputincorrectfigures,thatmeanstheprevious
input isineffective.Pleaseoperateagain. PS:Whencorrectingexistingdata,thebuttons(C),(.),(STOP) can
beoperatedatthesametime.Pleaserefertothediagram 4,5&6.Ifthecurrentfigureshownonthecontrol
unit is200.0andthecorrectonein100.0,thestepstooperateareasthefollowingdiagramsdemonstrated.
Diagram4
Current figure
shownis200.0
Step3:
Press button(1).
Step1:
pressbutton(SET).
Step4:
Press button(0)
twice.
Step5:
Press button(SET)
for2-3secondsand
takeyourfinger
away.Thefigure
100.0isshownon
thedisplay.Now,
thecorrecting
existingdatais
completed.
Step2:
Takeyourfingeraway
fromthebutton(SET),
then(0)onlyis shownon
thedisplay.
1.R1meansdimensionincreasing.
2.R2meansdimensiondecreasing.
3.R3meansathighspeed.
4.R4meansatlowspeed.
5.R5meansunderrunning.
6.R6meansjobfinished.
7.R7meansbraking.
PS: ThenumbersandfunctionoftheRelaywillbe
changed whenthemachinemodelisdifferent.
4.DESCROPTION OF RELAY FUNCTION
5.Operating Instruction For Correcting Data
1.In accordancewiththedimensionofthe actual material,press(SET)buttonand(0.)willshownonthe
display.Usecorrectfigures andpress (0 to9)buttons,thenpressbutton(SET)for2-3seconds.Thedisplay
will starttoflashandthenstopflashing.Finallythe figuresinput formerlywill beshownandcomplete
correctingdata.Ifthetimeforpressingthebutton(SET)orinputincorrectfigures,thatmeanstheprevious
input isineffective.Pleaseoperateagain. PS:Whencorrectingexistingdata,thebuttons(C),(.),(STOP) can
beoperatedatthesametime.Pleaserefertothediagram 4,5&6.Ifthecurrentfigureshownonthecontrol
unit is200.0andthecorrectonein100.0,thestepstooperateareasthefollowingdiagramsdemonstrated.
Diagram4
Current figure
shownis200.0
Step3:
Press button(1).
Step1:
pressbutton(SET).
Step4:
Press button(0)
twice.
Step5:
Press button(SET)
for2-3secondsand
takeyourfinger
away.Thefigure
100.0isshownon
thedisplay.Now,
thecorrecting
existingdatais
completed.
Step2:
Takeyourfingeraway
fromthebutton(SET),
then(0)onlyis shownon
thedisplay.
1.R1meansdimensionincreasing.
2.R2meansdimensiondecreasing.
3.R3meansathighspeed.
4.R4meansatlowspeed.
5.R5meansunderrunning.
6.R6meansjobfinished.
7.R7meansbraking.
PS: ThenumbersandfunctionoftheRelaywillbe
changed whenthemachinemodelisdifferent.
5
6
7
8
9
10
advertisement
Key Features
- Micro-computer controlled
- User-friendly interface
- Precise dimension setting
- Multiple dimension units(mm, INCH, 尺)
- Parameter calculation and setting
- Magnification setting
- Manual and automatic start operating modes
Related manuals
Frequently Answers and Questions
How do I change the dimension units on the DP 525?
Press the UNIT button to cycle through the available dimension units: mm, INCH, and 尺.
What are the input and output voltage specifications for the DP 525?
The power input is AC (0V-110V-220V) 50/60HZ + 20%, and the signal input is a standard ENCODERAB phase signal (DC12V).
What is the purpose of the SET button on the DP 525?
The SET button is used to set data, including correcting existing data and setting the 10th digit. Hold down the SET button for 2-3 seconds to confirm your input.
How do I set the parameter for the DP 525?
The parameter is set in accordance with the signal of the ENCODER and represents the actual dimension. To set the parameter, turn off the power switch, press the SET button, turn on the power switch, and input the calculated parameter while the display is flashing.
What is the function of the START and STOP buttons on the DP 525?
The START button initiates the automatic operation of the device, while the STOP button halts all operations, including input and automatic operation.
advertisement
