Avantco UDD2472S User manual
Avantco UDD2472S is a reliable and efficient beer dispenser that offers a range of features to enhance your beer-serving experience. With its powerful cooling system, this unit ensures your beverages are chilled to perfection, preserving their taste and quality. The adjustable temperature control allows you to customize the temperature to suit your preferences. This dispenser is designed for convenience, featuring a user-friendly control panel that makes it easy to adjust settings and monitor performance.
advertisement
Beer Dispenser User’s Manual
- 1 -
User Manual
UDD1, UDD1S, UDD2448, UDD2448S, UDD2460,
UDD2460S, UDD2472, UDD2472S
Please read the manual thoroughly prior to equipment set-up,
operation and maintenance.
07/2015
- 1 -
User Manual
UDD1, UDD1S, UDD2448, UDD2448S, UDD2460,
UDD2460S, UDD2472, UDD2472S
Please read the manual thoroughly prior to equipment set-up,
operation and maintenance.
07/2015
- 2 -User Manual
Table of Contents
Installation and Operation
Uncrating 3
Locating 3
Proper Disposal 4
Shelf Installation 4
Electrical Instruction 5
Draft Tower Installation 6
Drain Installation 7
Startup 7
Temperature Setting 7
Temperature 8
Pressure 8
Tapping 8
Storage & Handling 8
Regular Maintenance & Beer Setup
Knockout CO2 Installation 9
Changing CO2 Gas Cylinder 10
CO2 Pressure Adjustment 10
Cleaning the Bar System 11
Cleaning the Condenser Coil 12
Cleaning the Fan Blade and Motor 12
Cleaning the Interior of the Unit 12
Stainless Steel Care & Cleaning 13-14
Troubleshooting
Dispenser 15
Draft Beer 16-17
Warranty Information 17
PLEASE READ HANDBOOK BEFORE USING EQUIPMENT
AND KEEP FOR FUTURE USE
Notice: Use this appliance for its intended purpose as described in this
User Manual. A properly maintained unit will give you many years
of trouble free service.
Table of Contents
Installation and Operation
Uncrating 3
Locating 3
Proper Disposal 4
Shelf Installation 4
Electrical Instruction 5
Draft Tower Installation 6
Drain Installation 7
Startup 7
Temperature Setting 7
Temperature 8
Pressure 8
Tapping 8
Storage & Handling 8
Regular Maintenance & Beer Setup
Knockout CO2 Installation 9
Changing CO2 Gas Cylinder 10
CO2 Pressure Adjustment 10
Cleaning the Bar System 11
Cleaning the Condenser Coil 12
Cleaning the Fan Blade and Motor 12
Cleaning the Interior of the Unit 12
Stainless Steel Care & Cleaning 13-14
Troubleshooting
Dispenser 15
Draft Beer 16-17
Warranty Information 17
PLEASE READ HANDBOOK BEFORE USING EQUIPMENT
AND KEEP FOR FUTURE USE
Notice: Use this appliance for its intended purpose as described in this
User Manual. A properly maintained unit will give you many years
of trouble free service.
- 3 -User Manual
Installation & Operation
Uncrating
If the unit has recently been transported on its side, please let the unit stand upright for a
minimum of 24 hours before plugging it in.
1 Remove the outer packaging All of the packaging (including cardboard, bubbles and plastic
wrap) should be removed from the unit
2 Move the unit as close to the final location as possible before removing the wooden pallet
3 Use a screwdriver to remove the screws
from the L-bracket connecting the unit to
the wooden pallet
4 Remove pallet by unscrewing all base rail
anchor brackets Place pallet to the side
5 Carefully upright the cabinet
Locating
- Install the unit on strong and level surfaces, keep the cooler
stable to avoid vibration and noise
- Install the unit in an indoor, well-ventilated area A space of at
least 3” should be allowed between the surrounding walls and the
cabinet wall for air circulation
- Unit should be placed far from any heating source to avoid
decrease of refrigeration efficiency
- Install the cooler in a dry place to prevent rust from forming on
the compartment body, which may affect electrical insulation
- The appliance shall not be exposed to rain or sun Outdoor use
may cause decrease in efficiency and damage to the unit
- The unit should be placed close enough to the electrical outlet
so that extension cords are never used
Caution: When lifting unit
do not use the countertop
as a lifting point.
Caution: Problems caused by improper
position of units are not covered by warranty
!
!
Installation & Operation
Uncrating
If the unit has recently been transported on its side, please let the unit stand upright for a
minimum of 24 hours before plugging it in.
1 Remove the outer packaging All of the packaging (including cardboard, bubbles and plastic
wrap) should be removed from the unit
2 Move the unit as close to the final location as possible before removing the wooden pallet
3 Use a screwdriver to remove the screws
from the L-bracket connecting the unit to
the wooden pallet
4 Remove pallet by unscrewing all base rail
anchor brackets Place pallet to the side
5 Carefully upright the cabinet
Locating
- Install the unit on strong and level surfaces, keep the cooler
stable to avoid vibration and noise
- Install the unit in an indoor, well-ventilated area A space of at
least 3” should be allowed between the surrounding walls and the
cabinet wall for air circulation
- Unit should be placed far from any heating source to avoid
decrease of refrigeration efficiency
- Install the cooler in a dry place to prevent rust from forming on
the compartment body, which may affect electrical insulation
- The appliance shall not be exposed to rain or sun Outdoor use
may cause decrease in efficiency and damage to the unit
- The unit should be placed close enough to the electrical outlet
so that extension cords are never used
Caution: When lifting unit
do not use the countertop
as a lifting point.
Caution: Problems caused by improper
position of units are not covered by warranty
!
!
- 4 -User Manual
Shelf Installation
Shelves are included with the beer dispensers to provide the option for storage
1 Hook shelf clips onto clip hanger
2 Place shelves on shelf clips making sure all corners are seated properly
PROPER DISPOSAL OF EQUIPMENT DANGER!
RISK OF CHILD ENTRAPMENT SAFETY!
Proper Disposal of the Refrigerator
If you are getting rid of an old refrigerator, please follow the below instructions to help prevent a
terrible accident
- Remove the doors
- Leave shelves in place to prevent children from easily climbing inside
Do not allow children to climb, stand or hang on the shelves in the cooler They could damage the
unit and seriously injure themselves
Refrigerant Disposal
Your old refrigerator may have a cooling system that uses Ozone Depleting Chemicals If you are
throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a
qualified service technician If you intentionally release any refrigerant, you can be subject to fines
and imprisonment under provisions of the environmental regulations
Shelf Installation
Shelves are included with the beer dispensers to provide the option for storage
1 Hook shelf clips onto clip hanger
2 Place shelves on shelf clips making sure all corners are seated properly
PROPER DISPOSAL OF EQUIPMENT DANGER!
RISK OF CHILD ENTRAPMENT SAFETY!
Proper Disposal of the Refrigerator
If you are getting rid of an old refrigerator, please follow the below instructions to help prevent a
terrible accident
- Remove the doors
- Leave shelves in place to prevent children from easily climbing inside
Do not allow children to climb, stand or hang on the shelves in the cooler They could damage the
unit and seriously injure themselves
Refrigerant Disposal
Your old refrigerator may have a cooling system that uses Ozone Depleting Chemicals If you are
throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a
qualified service technician If you intentionally release any refrigerant, you can be subject to fines
and imprisonment under provisions of the environmental regulations
5
6
7
8
9
10
11
12
13
14
15
16
17
advertisement
Related manuals
advertisement