AKAI CAU-7160 car media receiver Instruction manual

The AKAI CAU-7160 is a car audio system with a USB/SD/MMC player and FM/AM radio tuner. It features volume control, bass and treble adjustment, balance and fader controls, and multiple EQ modes. It also includes a display for showing information and settings.

USB /SD /MMC /PLAYER
INSTALLATION
PRECAUT ION S
Choo se the mount ing loc at ion wher e the un it wi ll no t int er fer e wi th the no rmal
the dr ive r.
dr ivi ng fun ct ion of
Bef or e final ly inst al ling the uni t, connec t the wir ing tem por ar ily and make sur e it is all connected up
prope rly and the unit and the system work prope rly.
Use onl y the par ts incl uded wi th the uni t to ensur e pr oper inst al lat ion. The use of unauthorized
parts ca n ca use mal functions.
Consult wit h your nearest dealer if instal lati on requi res the dri lling of holes or other modificat ions of
the vehicl e.
Install the un it wh ere it does no t get in the dr iver's wa y an d ca nnot injure the passenger if there is
a su dden st op. Like an eme rgency st op.
Avoid installing the un it wh ere it wo uld be su bject to hi gh temp erature, such as from di rect
sunlight, or from hot air, form the heater, or where it would be subject to dust, dirt or excessive
vibration.
DI N FRON T-MOU NT (Me thod A)
Installing the un it
1. Da shboard
2. Ho lder
Af ter inserting the ho lder into the da shboard,
select the appropriate tab ac cording to the thickness
of the da shboard ma terial and be nd them inwa rds to
secure the ho lder in (Fig. 1)place.
3. Sc rew
(Fi g. 1)
1 2
3
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
be bent by hand to the desired angle.
7. Plain Washer.
(Fig.3)
2
1 3
Removing the unit
1
2
3
4
56
7
(Fig.2)
2 Insert fingers into the groove in the
frame and pull out to remo ve t he frame .
. front of
(Wh en reattaching the frame ,point the
side wi th a gr oovedow nw ards and att ach It.)
3.Leve r
Insert the levers supp lied with the
grooves at both si des of the unit and show n in
figure unti l they cl ick. Pu lling the levers makes
possibl e to rem ove the unit from the dash board.
unit into the
02
INPUT THE SD CARD
The SD oblique angle keeps Rightward
exposure, put into the SD slot and press
it again to eject.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on
sides of the unit.
the
Fastening the unit to the factory radio
mounting bracket:
1. Select a position where the screw holes
of the bracket and the screw holes of the
main unit become aligned (are fitted), and
tighten the screws at 2 places on each side.
Use either truss screws (5 x 5mm) or flush
surface screws (4 x 5mm).
2. Screw
3. Dashboard or Console
INSTALLATION
3
2
2
GENERAL OPERATIONS
FRONT PANEL LAYOUT
03
Power/MOD Button
Volume/Sel Button
Display/Mute Button
LCD Display
Reset Button
Band switch/ID3 select
Tune Seek & Track forward Button
Tune Seek & Track reverse Button
Automatically memory storing
Play/pause & Preset Button 1
Intro & Preset Button 2
Repeat & Preset Button 3
Random & Preset Button 4
Preset Button 5
Preset Button 6
Release Button
Remote Control sensor
AUX IN JACK
USB connecter
21
20
19
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
18
5
EQ OFF/ON
Select “EQ ON ” POP CLASS ROCK EQ OFF menu male.
GENERAL OPERATIONS
GENERAL OPERATIONS
SOUND ADJUSTMENT
Turn on (2) can adjust the desired volume quality.
Press SEL button (2) will change in the following order.
Option:
VOLUME
Adjust volume level by using (2) knob. Turn the VOL knob to left to decrease
the sound level, turn the VOL knob to right to increase the sound level.
VOL/SEL
Note: The unit is initially set to volume mode.
VOL BAS TRE BAL FAD
(Volume) (Bass) (Treble) (Balance) (Fader)
Press VOL/SEL button shortly and turn VOL button to right or left to select different
mode.
menu
BASS
Press VOL/SEL button(2) one time. Adjust bass level by u sing VOL/SEL(2) Knob.
TREBLE
Press VOL/SEL button(2) two times. Adjust treble level by using VOL/SEL(2) Knob .
BALANCE
Press VOL/SEL button(2) three times. Adjust sound balance between left and right
speakers by using VOL/SEL(2)Knob .
FADER (optional)
Press SEL button(2) four times. Adjust sound balance between front and rear speakers
by using VOL/SEL(2)Knob.
SELECT MENU
Press VOL/SEL button for several seconds, selecting menu is activated as cyclical mode
of following function for use's selection:
BASVOL TRE BAL EQLOUD OFF/ON
STEREO/MONO DX/LOC
FAD
04
SD/MMC slot
Flashing LED
POWER /MOD conversion
2.Under power off status,short press is power on,
Under power on status,short press is switching mode,long press is power off.
LOUD EQ
CAU-7160
20 21
18315 8 914 67
1910
11
13
41712 1216
BND AMS
CAU-7160
BN D AM S
CA U-7160

GENERAL OPERATIONS
AREA SETUP
In Radio mode. Press SEL button for several seconds. LCD will be show from BEEP ON
AREA USA/EUR. At AREA USA/EUR. You can use VOL +/- to select the AREA
frequency.
RADIO OPERATIONS
BAND SELECTION
At tuner mode, press BAND button (6) to select the desired band. The
change in the following order:
reception band will
05
Note: On Remote Control
RESET
RESET button (5) is placed on the housing and must be activated with either a ball point
pen or thin metal object. (Do not use sharp object to avoid damaging the unit.) The RESET
button (5) is to be activated for the following reasons:
- Initial installation of the unit when all wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
STATION SELECTIONSTATION SELECTION
During radio mode, Press “SEEK ” or “SEEK ”buttons shortly to automatically
a station, Press “SEEK ” or “SEEK ” buttons more than 1 second is operated as
manual turning mode.
search
- Program Scanning
Press AMS(MP3) button (9) shortly to scan preset station. When the AMS mode is carry out,
“INT” appear on LCD display, the unit scan each stored station for 5 seconds, you also can press
the corresponding number button or AMS button. Your desired station will start playing.
And then 6 strongest stations are stored into the corresponding preset number button.
STATION STORING
Press preset button (11~16)
RADIO MODE.
M1 ~ M6
- PRESET MEMORY is loaded when key is pressed for less than 1 second.
- PRESET MEMORY is saved when key is pressed for longer than 1 sec.
RADIO OPERATIONS
06
SELECT TRACKS
During USB/SD operation, press SEEK " " button or " " button to move
to the previous track or the following track, Track number shows on display. During / ,
hold SEEK " " (8) button or SEEK " "(7) to fast reverse or fast forward. Music play
starts from when you release the button.
Press preset button (15-16):
- MP3 MODE : 10 TRACK UP / DOWN is activated.
When the total track is 10 or less, KEY is inactivated.
(8) SEEK (7)
USB SD
RPT
Press preset button (12): Flash play mode : REPEAT ON / OFF is activated.
When REPEAT ON, RPT INDICATOR comes on and repeats the current music track.
RDM
During RANDOM ON, RDM INDICATOR is turned on
track of disc is played in ramdom instead of normal order.
Press preset button (13): and each
USB/SD FLASH MP3 Playing：
PLAY / PAUSE
Press button (10) pause function Music track play time
Press it again to resum palying, press it more than 1 second is TOP function.
is activated. INDICATOR flashes.
INT
Press button (11): During INTRO ON, INT indicator comes on and begins
Playing the first 10sec of each song, until the last song is played. It begins playing the entire
track from where INT started
USB/SD OPERATIONS
AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING
- Automatically Memory Storing
Press AMS(MP3) button (9) for several seconds, the radio searches from the
frequency and checks the signal strength until one cycle search is finished.
current
07
SPECIFICATION
General
Power Supply Requirements:
Maximum Output Power:
Chassis Dimensions: 178 x 130x 50mm (W x D x H)
Tone Controls
Bass (at 100Hz): +10dB / -10dB
Treble (at 10K): +10dB / -10dB
Current Drain: 5A
USB/SD MUSIC Player
Signal to Noise Ratio: More than 60dB
Channel Separation: More than 60dB
Frequency Response:
FM Radio
Frequency Coverage (MHz):
IF:
Sensitivity (S/N-30dB):
Stereo Separation:
20Hz - 20KHz
87.5 - 108MHz
10.7MHz
12dBu
>30dB
4 x 25W
Load Impedance: 4 ohms
DC 14.4V , Negative Ground
Short press “DISP” button to turn on the mute, Press “DISP” again to turn
off the mute.
Long press “DISP”, LCD screen shows clock “00:00”. Short press “DISP”,
the hour flashes, rotate “VOL +/-“to adjust hour. Press “SEL” button, minute
flashes, rotate “VOL +/-“ to adjust the minute. If there is no operation within
5 seconds, the unit will memorize the current time and return to current mode.
REAR Lch LINE OUT
REAR Rch LINE OUT
BLUE
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK
RED YELLOW
BLACK
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
5
AM Radio
Frequency Coverage (KHz): 520 - 1620 KHz
IF:
Sensitivity (S/N-20dB): 42dBu
450KHz
Remarks:
Specifications subject to change without notice
ADDITIONAL INFORMATION