AV Access 4KEX70-L HDBase-T Lite Extender User Manual

AV Access 4KEX70-L is a powerful HDBaseT Lite Extender that allows you to transmit 4K@60Hz and 1080P@60Hz signals up to 40m and 70m respectively over a single Cat 6a/7 cable. With bi-directional IR pass-through, you can control your source device from the display's location or vice versa. The slim and space-saving design makes it easy to install in various environments.

HDBase-T Lite Extender
User Manual
4KEX70-L

Introduction
Introduction
Overview
This product is a slim transmitter receiver pair which is designed to extend
HDMI 1080P@60Hz signals up to 70m/230ft and 4K@60Hz signals up to
40m/131ft via a single Cat 6a/7 cable. The transmitter and receiver can
supply power to each other reciprocally. When either side is plugged in the
power, both sides are powered on. You can control the source from the
display's location or control the display from source's location via IR
pass-through function. The transmitter and receiver are easy to install. They
are space saving and offer solutions for home, office, digital entertainment
centers, control centers, conference rooms, school and corporate training
environments.
Features
 Slim appearance and space saving.
 Bi-directional POE, when either side (transmitter or receiver) is
plugged in the power, both sides are powered on.
 Transfers bi-directional infrared control signal together with the HDMI
signal.
 Via Cat 6a/7 cables, 4Kx2K@60Hz (4:2:0) output up to 40m/131ft,
1080P@60Hz up to 70m/230ft.
 Via Cat 5e cable, 4Kx2K@60Hz (4:2:0) output up to 35m/115ft,
1080P@60Hz up to 60m/197ft.
 HDMI 1.4 with 4K and HDCP 2.2 compliant.
 Supports Bi-directional RS232 pass through.
Package Contents
Before you start the installation of the product, please check the package
contents:
 Transmitter x 1
 Receiver x1
 Power Adapter (DC 18V 1A) x1
 IR Emitter x1
 IR Receiver (30 KHz ~ 50 KHz) x1
 Phoenix Connectors (3.5mm, 3 Pins) x 2
 User Manual x 1

Introduction
Panel
Front Panel
Transmitter & Receiver
No. Name Description
1 Power On: The device is powered on.
Off: The device is powered off.
2 Status Blinking: The device is working properly.
Off: The device is not working properly.
3 HDCP
On: HDCP protected content is being transmitted.
Blinking: Non-HDCP protected content is being
transmitted.
Off: No content is being transmitted.
4 Link
On: Link between transmitter and receiver has been
established.
Off/Blinking: Connection exceptions exist between
transmitter and receiver.
Rear Panel
Transmitter
No. Name Description
1 DC 18V
Connect to a DC 18V 1A power adapter.
Note: If transmitter is connected to a power supply,
the receiver is adapter free.
2 HDBT Out Connect to the receiver via a Cat5e/6 cable.
3 IR In Connect to an IR receiver cable. Secure the IR
receiver with adhesive.
4 IR Out Connect to an IR emitter cable. Secure the IR emitter
on the IR receiving sensor of source device with
adhesive.
5 RS232 RS232 pass-through
6 HDMI In Connect to a source device via an HDMI cable.

Application
Receiver
No. Name Description
1 DC 18V
Connect to a DC 18V 1A power adapter.
Note: If receiver is connected to a power supply,
transmitter is adapter free.
2 HDBT In Connect to the transmitter via a Cat5e/6 cable.
3 IR In Connect to an IR receiver cable. Secure the IR
receiver with adhesive.
4 IR Out Connect to an IR emitter cable. Secure the IR
emitter on the IR receiving sensor of display device
with adhesive.
5 RS232 RS232 pass-through.
6 HDMI Out Connect to a display via an HDMI cable.
ApplicationPower Supply
Connect the power
adapter provided to
the transmitter/
receiver to power
both units.
6
Connect the
HDMI source
4
Use Cat 5e/6/7 to connect the transmitter and receive r.3
1 Connect the
HDMI display
Connect IR
receiver cable to
IR In port of
receiver.
Connect IR
emitter cable to
IR Out port of
transmitter.
2
5
Transmitter
Receiver
DVD Remote