HiLook NS-0109P-60(B) 8 Port Fast Ethernet Unmanaged POE Switch Quick Start Guide

HiLook NS-0109P-60(B) 8 Port Fast Ethernet Unmanaged POE Switch Quick Start Guide

advertisement

2 3
Applicable Models
This manual is applicable to NS-0105P and NS-0109P series 100M long-range PoE switch.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
·
·During the installation and utilization of the device, please strictly conform to electrical
safety rules in different nations and regions.
·Ensure to use the attached power adaptor only and not to change the adaptor randomly.
Please refer to specification table for specific requirements of power adaptor.
·If the product does not work properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
·The device must be installed in machine room only, and only maintenance staff or
qualified person should access to the device.
·Do not touch the upper cover area of the device that may be overheated.
·Power must be shut down during cable connection, device installation and
dismantlement.
·You shall acknowledge that the use of the device with Internet access might be under
network security risks, please strengthen protection for your personal information and
data security. If you find the device might be under network security risks, please contact
with us.
·Proper configuration of all passports and other security settings is the responsibility of
the installer, and you shall keep user name and passports properly.
·Please keep all original packing materials properly. If the product does not work
properly, pack the switch in its original packing materials for shipping. We shall not assume
any responsibility for damages caused by improper packing materials during shipping.
·Ensure that your devices powered via the PoE port have their shells protected and
fire-proofed, because the switches are not compliant with the Limited Power Source (LPS)
standard.
·This is a class A product and may cause radio interference in which case the user may be
required to take adequate measures.
4 5
Device Connection
Connect your devices according to your actual networking requirements.
Interfaces
Rear Panel
Grounding Terminal
Power Interface
DIP Switch
On: Extend model is on, connecting PoE port 1-4 (4 ports), 1-8 (8 ports).
Off: Extend model is off.
Grounding Terminal
The grounding terminal connects with ground cable in case of lightning.
Power Port
Connect power port of the switch with power socket with power cord
to provide power to the switch.
Front Panel
Packing List
1
Switch x 1 Quick Start Guide x 1Power Adapter x 1
DIP Switch
PoE Ports
100M PoE ports connect to other PoE devices with network cable.
UPLINK
100M network port connects to other switches with network cable.
PWR Indicator
Solid means powered up normally. Unlit means no power supply
connected or power supply is abnormal.
PoE-MAX Indicator
Solid/flashing means the output power of the switch will reach the
upper limit, and the power supply may be abnormal if more devices
are connected. Unlit means power supplying is normal.NS-0105P Series
NS-0109P Series
1 2 3 4 5
LINK/ACT Indicator
PoE Indicator
PoE-MAX Indicator
PWR
Indicator PoE Ports UPLINK
1 2 3 4 5 6 7 8 9
PoE-MAX Indicator
PWR
Indicator
LINK/ACT Indicator PoE Indicator
PoE Ports UPLINK Up to 250 m
Camera
100M PoE Switch
Convergence Switch NVR Monitor
Indicates a hazard with a high level of risk, which if
not avoided, will result in death or serious injury.
Symbol Description
Provides additional information to emphasize or
supplement important points of the main text.
Indicates a potentially hazardous situation, which if not
avoided, could result in equipment damage, data loss,
performance degradation, or unexpected results.
4/8-Port 100M Long-Range PoE Switch
Quick Start Guide
Power-On Checking Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
See the following table and check whether your devices are correctly
connected. After proper connection, you can use your switch without
doing any settings.
Indicator Status Description
PWR
Solid
Unlit
Solid
Unlit
Flashing
The switch is powered on normally.
No power supply connected or power
supply is abnormal.
Link/Act
The port is connected.
The port is transmitting data.
The port is disconnected or connection
is abnormal.
Please use the attached power cord in package to power up the switch.
The switch supports auto MDI/MDIX of ports, you can use
straight-through cable or crossover cable to connect the switch
and opposite Ethernet devices.
UD15463B
6 7 8
PoE Solid
Unlit
The switch provides power supply to PD
normally.
The switch is disconnected to PD, or
provides power supply to PD abnormally.
PoE-MAX
Solid
/Flashing
Unlit
The output power of the switch will reach
the upper limit. The power supply may be
abnormal if more devices are connected.
The switch provides power supply to PD
normally.
Quick Start Guide
COPYRIGHT ©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the
properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter
referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”)
cannot be reproduced, changed, translated, or distributed, partially or wholly, by any
means, without the prior written permission of Hikvision. Unless otherwise stipulated,
Hikvision does not make any warranties, guarantees or representations, express or implied,
regarding to the Manual.
About this Manual
This Manual is applicable to NS-0105P and NS-0109P series 100M long-range PoE switch.
The Manual includes instructions for using and managing the product. Pictures, charts,
images and all other information hereinafter are for description and explanation only. The
information contained in the Manual is subject to change, without notice, due to firmware
updates or other reasons. Please find the latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in
various jurisdictions. Other trademarks and logos mentioned below are the properties of
their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED,
WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS
AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY
SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG
OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS
OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN
IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT
THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATER PREVAILS.
  • Page 1
  • Page 2
/

advertisement

Related manuals

advertisement