Jireh PIT GAGE CLASSIC - Manual Pit Inspection Tool User Manual
Jireh PIT GAGE CLASSIC - Manual Pit Inspection Tool is a versatile tool designed for inspecting pits and other confined spaces. It features a center base and extension arms that can be used in various configurations to measure the depth of pits and other areas. The device can be used to measure the depth of pipes as well. The optional reverse spring indicator allows for accurate measurements on flat surfaces.
advertisement
PIT GAGE
Manual Pit Inspection Tool
PG0013 Rev 04.1
780.922.4534
jireh.com
53158 Range Road 224
Ardrossan, Alberta
Canada T8E 2K4
Manual Pit Inspection Tool
PG0013 Rev 04.1
780.922.4534
jireh.com
53158 Range Road 224
Ardrossan, Alberta
Canada T8E 2K4
OPERATING INSTRUCTIONS
1. Centre Base (Fig. 1-B)
The centre base may be used alone
or in part with multiple extension
arms.
2. Extension Arms (Fig. 1-C)
The extension arms may be used
in any configuration. A small radius
on the bottom surface assists with
measuring small diameter pipes.
3. Blind Side Base (Fig. 2-A)
When the centre base can not be used
appropriately. (i.e. Close to a weld or
flange) Loosen the thumb screw on the
rear of the centre base. Remove the
digital indicator (Fig. 1-A) and mount in
the blind side base. Retighten thumb
screw.
(Fig. 2-B) Additional clearance may be
obtained by rotating the digital indicator 90° before tightening the thumb screw.
An additional indicator tip (Fig. 1-D) has been included in this kit.
PREPARATION FOR USE
4. Setting the Count Direction
The +/- button switches the count direction of display values with respect to the
spindle direction.
5. Setting the Origin
Place gage on a known flat surface. Press and hold the ORIGIN button until
0.00 mm (0.0000 in) is displayed. Note: Origin can be set at any spindle position.
6. Reverse Spring Indicator (Optional)
On flat surface, depress plunger until needle contacts surface.
Troubleshooting Error Messages
B Replace battery. Note: Origin is cleared when battery is replaced.
C Condensation may have affected the unit. Turn off device and wait 2 hours
for thermal stabilization. If message still appears, return indicator for service.
CB
D
A
CB
D
A
Fig. 1
B A
Fig. 2
1. Centre Base (Fig. 1-B)
The centre base may be used alone
or in part with multiple extension
arms.
2. Extension Arms (Fig. 1-C)
The extension arms may be used
in any configuration. A small radius
on the bottom surface assists with
measuring small diameter pipes.
3. Blind Side Base (Fig. 2-A)
When the centre base can not be used
appropriately. (i.e. Close to a weld or
flange) Loosen the thumb screw on the
rear of the centre base. Remove the
digital indicator (Fig. 1-A) and mount in
the blind side base. Retighten thumb
screw.
(Fig. 2-B) Additional clearance may be
obtained by rotating the digital indicator 90° before tightening the thumb screw.
An additional indicator tip (Fig. 1-D) has been included in this kit.
PREPARATION FOR USE
4. Setting the Count Direction
The +/- button switches the count direction of display values with respect to the
spindle direction.
5. Setting the Origin
Place gage on a known flat surface. Press and hold the ORIGIN button until
0.00 mm (0.0000 in) is displayed. Note: Origin can be set at any spindle position.
6. Reverse Spring Indicator (Optional)
On flat surface, depress plunger until needle contacts surface.
Troubleshooting Error Messages
B Replace battery. Note: Origin is cleared when battery is replaced.
C Condensation may have affected the unit. Turn off device and wait 2 hours
for thermal stabilization. If message still appears, return indicator for service.
CB
D
A
CB
D
A
Fig. 1
B A
Fig. 2
advertisement
Key Features
- Center Base
- Extension Arms
- Blind Side Base
- Digital Indicator
- Depth Measurement
Related manuals
Frequently Answers and Questions
How do I set the count direction of the display values?
You can switch the count direction of the display values by pressing the +/- button. This determines whether the display values increase or decrease as the spindle moves.
How do I set the origin of the gage?
Place the gage on a known flat surface. Press and hold the ORIGIN button until 0.00 mm (0.0000 in) is displayed. You can set the origin at any spindle position.
What should I do if the device displays an error message?
If the device displays an error message, first check the battery. If the battery is low, replace it. If the error message persists, it may be due to condensation. Turn off the device and wait 2 hours for thermal stabilization. If the error message does not disappear, contact Jireh for service.
advertisement
