Jireh STIX - Manual Flange Scanner Owner's Manual
Jireh STIX - Manual Flange Scanner is designed for inspecting flanges, such as for corrosion detection. It features a two-probe configuration for efficient scanning and magnetic wheels for secure movement on cylindrical surfaces. The scanner accommodates various flange diameters, providing a reliable solution for industrial inspection needs.
advertisement
STIX
Manual Flange Scanner
DX0022 Rev 01.1
Manual Flange Scanner
DX0022 Rev 01.1
PAGE i of iv DX0022 Rev 01.1
SAFETY WARNINGS / PRECAUTIONS
WARNING! The STIX is designed for a specific use. Using the STIX
outside of its intended use could cause damage to the product. Read and
understand this manual before using.
KEEP THIS MANUAL – DO NOT LOSE
THIS MANUAL IS PART OF THE STIX AND MUST BE RETAINED FOR THE LIFE OF
THE PRODUCT. PASS ON TO SUBSEQUENT OWNERS.
Ensure any amendments are incorporated with this document.
WARNING! Can be harmful to pacemaker and ICD wearers. Stay at
least 25 cm (10 in) away.
WARNING! Do NOT operate scanner in an explosive environment.
Do NOT operate scanner in the presence of volatile substances.
The WEEE symbol indicates that the product must not be disposed of as
unsorted municipal waste, but should be collected separately.
(see Disposal on page 31 for additional details).
WARNING! DO NOT DISASSEMBLE. No user-serviceable parts.
Disassembling any of the components in this product, beyond the
instructions in this user manual, could void the regulatory certifications and/
or effect the safety of the product.
SAFETY WARNINGS / PRECAUTIONS
WARNING! The STIX is designed for a specific use. Using the STIX
outside of its intended use could cause damage to the product. Read and
understand this manual before using.
KEEP THIS MANUAL – DO NOT LOSE
THIS MANUAL IS PART OF THE STIX AND MUST BE RETAINED FOR THE LIFE OF
THE PRODUCT. PASS ON TO SUBSEQUENT OWNERS.
Ensure any amendments are incorporated with this document.
WARNING! Can be harmful to pacemaker and ICD wearers. Stay at
least 25 cm (10 in) away.
WARNING! Do NOT operate scanner in an explosive environment.
Do NOT operate scanner in the presence of volatile substances.
The WEEE symbol indicates that the product must not be disposed of as
unsorted municipal waste, but should be collected separately.
(see Disposal on page 31 for additional details).
WARNING! DO NOT DISASSEMBLE. No user-serviceable parts.
Disassembling any of the components in this product, beyond the
instructions in this user manual, could void the regulatory certifications and/
or effect the safety of the product.
PAGE ii of iv
Chapter
1 Identification 1
1.1. Product Brand 1
1.2. Manufacturer 1
Chapter
2 Product Specifications 2
2.1. Intended Use 2
2.1.1. Operating Limits 2
2.1.2. Operating environment 2
2.1.3. User 2
2.2. Unintended Use 2
2.3. Dimensions and Weight 3
2.4. Environmental Sealing 3
2.5. Performance Specifications 3
Chapter
3 Definitions 4
3.1. Definition of Symbols 4
Chapter
4 System Components 5
4.1. Component Identification 5
4.2. Tools 6
4.2.1. Included Tools 6
4.3.
Flange Scanner Frame 7
4.3.1. Articulated Side Frames 7
4.3.2. Probe Centre Spacing 9
4.4. Dovetail Handle 11
4.5. Brake 12
4.6. Flange Scanner Guides 12
4.7. Magnetic Wheels 14
4.7.1. Wheel Removal 14
4.7.2. Wheel Installation 15
4.8. Frame Bar with Ruler 15
4.9. Spring-Loaded Encoder 16
4.10. Cable Clips 16
4.11. Spring-Loaded Probe Holder 17
4.11.1. Probe Holder Setup 17
TABLE OF CONTENTS
Chapter
1 Identification 1
1.1. Product Brand 1
1.2. Manufacturer 1
Chapter
2 Product Specifications 2
2.1. Intended Use 2
2.1.1. Operating Limits 2
2.1.2. Operating environment 2
2.1.3. User 2
2.2. Unintended Use 2
2.3. Dimensions and Weight 3
2.4. Environmental Sealing 3
2.5. Performance Specifications 3
Chapter
3 Definitions 4
3.1. Definition of Symbols 4
Chapter
4 System Components 5
4.1. Component Identification 5
4.2. Tools 6
4.2.1. Included Tools 6
4.3.
Flange Scanner Frame 7
4.3.1. Articulated Side Frames 7
4.3.2. Probe Centre Spacing 9
4.4. Dovetail Handle 11
4.5. Brake 12
4.6. Flange Scanner Guides 12
4.7. Magnetic Wheels 14
4.7.1. Wheel Removal 14
4.7.2. Wheel Installation 15
4.8. Frame Bar with Ruler 15
4.9. Spring-Loaded Encoder 16
4.10. Cable Clips 16
4.11. Spring-Loaded Probe Holder 17
4.11.1. Probe Holder Setup 17
TABLE OF CONTENTS
PAGE iii of iv DX0022 Rev 01.1
4.12. Pivot Buttons 18
Chapter
5 Configurations 19
5.1. Two Probe 19
Chapter
6 Operation 20
6.1. Setup on a scan surface 20
Chapter
7 Maintenance 24
Chapter
8 Troubleshooting 25
8.1. Technical Support 25
Chapter
9 Service and Repair 26
Chapter
10 Spare Parts 27
10.1. Flange Scanner Components 27
10.1.1. Encoder Connector Type 28
10.2.STIX Kit Components 29
10.3. Probe Holder Components 30
10.3.1. Arm Style 30
10.3.2. Pivot Button Style 30
10.4. Variable Components 30
10.4.1. Frame Bars 30
Chapter
11 Disposal 31
Chapter
12 Limited Warranty 32
4.12. Pivot Buttons 18
Chapter
5 Configurations 19
5.1. Two Probe 19
Chapter
6 Operation 20
6.1. Setup on a scan surface 20
Chapter
7 Maintenance 24
Chapter
8 Troubleshooting 25
8.1. Technical Support 25
Chapter
9 Service and Repair 26
Chapter
10 Spare Parts 27
10.1. Flange Scanner Components 27
10.1.1. Encoder Connector Type 28
10.2.STIX Kit Components 29
10.3. Probe Holder Components 30
10.3.1. Arm Style 30
10.3.2. Pivot Button Style 30
10.4. Variable Components 30
10.4.1. Frame Bars 30
Chapter
11 Disposal 31
Chapter
12 Limited Warranty 32
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
advertisement
Key Features
- Two-probe configuration
- Magnetic wheels
- Adjustable diameter
- Spring-loaded encoder
- Guides for alignment
- Brake for holding
- Articulated side frames
Related manuals
Frequently Answers and Questions
How do I adjust the STIX scanner to different flange diameters?
Loosen the black wing knobs on the side frames, pivot the frame to the desired diameter using the diameter indicator, then tighten the knobs.
What is the minimum flange diameter that the STIX scanner can accommodate?
The minimum flange diameter for the STIX scanner is 7.6 cm (3 in) for a two-probe arrangement.
What are the magnetic wheels used for?
The magnetic wheels are designed to securely grip the flange surface, allowing for smooth and controlled scanner movement.
How do I install the magnetic wheels?
Remove the articulated side frame. Locate the threaded side of the magnetic wheel and screw it onto the axle. Tighten the wheel with the 3 mm hex driver.
How do I adjust the probe spacing on the STIX scanner?
The probe spacing can be adjusted by sliding one half of the articulated side frame along the frame bar, or by placing the wedge in alternate pivot button holes of the probe holder.
advertisement
