Musway ONE1500 Amplifier Owner's Manual

Musway ONE1500 Amplifier Owner's Manual

The Musway ONE1500 is a powerful digital Class D mono amplifier, designed specifically for use in vehicles. This amplifier delivers impressive power outputs, with 450 watts RMS at 4 ohms, 900 watts RMS at 2 ohms and 1550 watts RMS at 1 ohm, making it suitable for powering even the most demanding subwoofers. It features a wide range of settings like input sensitivity, subsonic and low pass filters, bass boost and phase shift. The ONE1500 also includes automatic turn-on functionality, allowing it to power up when your car stereo is switched on, enhancing the driving experience with high-quality sound.

advertisement

VERSION 1.0
ONE1500DIGITAL CLASS D MONO AMPLIFIER
M X S E R I E S
2ENGLISH
THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION WITH A 12V ON-BOARD ELECTRI-
CAL SYSTEM OF A VEHICLE. Otherwise fire hazard, risk of injury and electric shock consists.
PLEASE DO NOT MAKE ANY OPERATION OF THE SOUND SYSTEM, WHICH DISTRACT YOU FROM A
SAFE DRIVING. Do not make any procedures, which demand a longer attention. Perform these operations not
until you have stopped the vehicle on a safe place. Otherwise the risk of accident consists.
ADJUST THE SOUND VOLUME TO AN APPROPRIATE LEVEL, THAT YOU ARE STILL ABLE TO HEAR
EXTERIOR NOISES WHILE DRIVING. High performance sound systems in vehicles may generate the acous-
tic pressure of a live concert. The permanent listening to extreme loud music may cause the loss of your hear-
ing abilities. The hearing of extreme loud music while driving may derogate your cognition of warning signals in
the traffic. In the interests of the common safeness, we suggest to drive with a lower sound volume. Otherwise
the risk of accident consists.
DO NOT COVER COOLING VENTS AND HEAT SINKS. Otherwise this may cause heat accumulation in the
device and fire hazard consists.
DO NOT OPEN THE DEVICE. Otherwise fire hazard, risk of injury and electric shock consists. Also this may
cause a loss of the warranty.
REPLACE FUSES ONLY WITH FUSE WITH THE SAME RATING. Otherwise fire hazard and risk of electric
shock consists.
DO NOT USE THE DEVICE ANY LONGER, IF A MALFUNCTION OCCURS, WHICH REMAINS NOT REM-
EDIED. Refer in this case to the chapter TROUBLE SHOOTING. Otherwise risk of injury and the damage of
the device consists. Commit the device to an authorized retailer.
INTERCONNECTION AND INSTALLATION SHOULD BE ACCOMPLISHED BY SKILLED STAFF ONLY. The
interconnection and installation of this device demands technical aptitude and experience. For your own safe-
ness, commit the interconnection and installation to your car audio retailer, where you have purchased the
device.
DISCONNECT THE GROUND CONNECTION FROM THE VEHICLE’S BATTERY BEFORE INSTALLATION.
Before you start with the installation of the sound system, disconnect by any means the ground supply wire
from the battery, to avoid any risk of electric shock and short circuits.
CHOOSE AN APPROPRIATE LOCATION FOR THE INSTALLATION OF THE DEVICE. Look for an appropri-
ate location for the device, which ensures a sufficient air circulation. The best places are spare wheel cavities,
and open spaces in the trunk area. Less suitable are storage spaces behind the side coverings or under the
car seats.
DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT WILL BE EXPOSED TO HIGH HUMIDITY AND
DUST. Install the device at a location, where it will be protected from high humidity and dust. If humidity and
dust attain inside the device, malfunctions may be caused.
MOUNT THE DEVICE AND OTHER COMPONENTS OF THE SOUND SYSTEM SUFFICIENTLY. Otherwise
the device and components may get loose and act as dangerous objects, which could cause serious harm and
damages in the passenger room.
ENSURE CORRECT CONNECTION OF ALL TERMINALS. Faulty connections may could cause fire hazard
and lead to damages of the device.
MOUNT THE DEVICE AND OTHER COMPONENTS OF THE SOUND SYSTEM SUFFICIENTLY. Otherwise
the device and components may get loose and act as dangerous objects, which could cause serious harm and
damages in the passenger room.
SAFETY INSTRUCTIONS
3ENGLISH
ENSURE NOT TO DAMAGE COMPONENTS, WIRES AND CABLES OF THE VEHICLE WHEN YOU DRILL
THE MOUNTING HOLES. If you drill the mounting holes for the installation into the vehicle’s chassis, ensure
by any means, not to damage, block or tangent the fuel pipe, the gas tank, other wires or electrical cables.
DO NOT INSTALL AUDIO CABLES AND POWER SUPPLY WIRES TOGETHER. Ensure while installation
not to lead the audio cables between the head unit and the processor together with the power supply wires
on the same side of the vehicle. The best is a areal separated installation in the left and right cable channel of
the vehicle. Therewith a overlap of interferences on the audio signal will be avoided. This stands also for the
equipped bass-remote wire, which should be installed not together with the power supply wires, but rather with
the audio signal cables.
ENSURE THAT CABLES MAY NOT CAUGHT UP IN CLOSE-BY OBJECTS. Install all the wires and cables
like described on the following pages, therewith these may not hinder the driver. Cables and wires which are
installed close-by the steering wheel, gear lever or the brake pedal, may caught up and cause highly danger-
ous situations.
DO NOT SPLICE ELECTRICAL WIRES. The electrical wires should not be bared, to provide power supply to
other devices. Otherwise the load capacity of the wire may get overloaded. Use therefor a appropriate distribu-
tion block. Otherwise fire hazard and risk of electric shock consists.
DO NOT USE BOLTS AND SCREW NUTS OF THE BRAKE SYSTEM AS GROUND POINT. Never use for
the installation or the ground point bolts and screw-nuts of the brake system, steering system or other security-
relevant components. Otherwise fire hazard consists or the driving safety will be derogated.
ENSURE NOT TO BEND OR SQUEEZE CABLES AND WIRES BY SHARP OBJECTS. Do not install cables
and wires not close-by movable objects like the seat rail or may be bent or harmed by sharp and barbed edges.
If you lead a wire or cable through the hole in a metal sheet, protect the insulation with a rubber grommet.
KEEP AWAY SMALL PARTS AND JACKS FROM CHILDREN. If objects like these will be swallowed, the risk
of serious injuries consists. Consult promptly a medical doctor, if a child swallowed a small object.
QUESTIONS REGARDING PRODUCT SAFETY. If you have any further questions regarding product safety,
please contact us by e-mail at [email protected]
SAFETY INSTRUCTIONS
DISPOSAL/RECYCLING
If you have to dispose the device and its components, please note that no electronic devices must
be disposed in the household waste. Dispose the device and its components at a suitable recy-
cling facility in accordance with local waste regulations. If necessary, consult your local authority
or dealer.
More information at www.audiodesign.de/english/disposal
5 ~ 50°C10 ~ 90%
4ENGLISH
TECHNICAL SPECIFICATIONS
Model ONE1500
Channels 1
Circuit Digital Class D
OUTPUT POWER RMS @ 14.4 V
Watts @ 4 Ohms
Watts @ 2 Ohms
Watts @ 1 Ohm
1 x 450
1 x 900
1 x 1550
Frequency Range –3dB 8 - 1300 Hz
Damping Factor 1875
Signal-to-Noise Ratio 103 dB
THD+N @ 5 W 0,015 %
Input Sensitivity High Level: 430 mV - 10,9 V
Low Level: 210 mV - 7,1 V
Filter Section
Sub Sonic Filter
Low Pass Filter
Bass Boost
Phase Shift
10 - 40 Hz
40 - 150 Hz
0 - 18 dB @ 45 Hz
0 - 180°
Start-stop capability Yes
High Level Inputs with EPS Yes
Auto Turn On Via DC or Signal
Bass Level Remote Controller Yes
Fuse Rating 1 x 120 A (external)
Dimensions 150 x 45 x 260 mm
All Specifications are subject to change
This product is designed to operate in a vehicle with an on-board voltage of +12 V with negative ground. The
device functions as an audio amplifier that is used within a vehicle sound system.
INTENDED USE
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
  • Page 1
  • Page 2
  • Page 3
  • Page 4
  • Page 5
  • Page 6
  • Page 7
  • Page 8
  • Page 9
  • Page 10
  • Page 11
  • Page 12
  • Page 13
  • Page 14
  • Page 15
  • Page 16
  • Page 17
  • Page 18
  • Page 19
  • Page 20
  • Page 21
  • Page 22
  • Page 23
  • Page 24
  • Page 25
  • Page 26
  • Page 27
  • Page 28
  • Page 29
  • Page 30
  • Page 31
  • Page 32
  • Page 33
  • Page 34
  • Page 35
  • Page 36
/

advertisement

Key Features

  • Digital Class D
  • 450W RMS @ 4 Ohms
  • Subsonic & Low Pass Filters
  • Bass Boost
  • Phase Shift
  • Auto Turn On
  • Bass Remote Controller

Related manuals

Frequently Answers and Questions

How much power does the Musway ONE1500 deliver?
The ONE1500 amplifier delivers a remarkable 450 watts RMS at 4 ohms, 900 watts RMS at 2 ohms, and 1550 watts RMS at 1 ohm.
What types of filters does this amplifier offer?
The Musway ONE1500 features both subsonic and low pass filters, allowing you to tailor the sound to your preferences and subwoofer setup.
Can I adjust the bass level with the Musway ONE1500?
Yes, the ONE1500 amplifier includes a bass level remote controller, which allows you to adjust the bass output from the driver's seat.
How does the Auto Turn On feature work?
The ONE1500 amplifier can be set up to automatically turn on when your car stereo is switched on. You can select either DC or signal-based activation.

advertisement