XPR B100-SA Owner's Manual
xpr B100-SA is a standalone biometric reader designed for easy management of users and configuration. It features advanced capacitive sensing technology for enhanced security and reliability. The device can store up to 100 fingerprint templates, including user, administrator, and installer profiles. It also offers adjustable relay timings and programming options for customized access control.
advertisement
www.xprgroup.com1
Standalone Biometric Reader
ENB100-SA v2
INSTALLER’S MANUAL
Rev. 1.01 - 31.03.2022
Standalone Biometric Reader
ENB100-SA v2
INSTALLER’S MANUAL
Rev. 1.01 - 31.03.2022
www.xprgroup.com2
1. INTRODUCTION
2. MOUNTING
3. SPECIFICATIONS
4. APPLICATION DIAGRAM
5. RECOMMENDED SWIPING TECHNIQUE
6. INDICATION
7. WIRING
8. ADDING ADMIN FINGER
9. PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT
Pairing B100-SA v2 with DINRTT
Pairing B100-SA v2 with RTT
Pairing B100-SA v2 with RU2
10. ADMINISTRATOR PROGRAMMING
ADD finger relay 1
ADD finger relay 2
ADD finger relay 1&2
DELETE finger
DELETE ALL fingers
CHANGE ADMIN finger
CHANGE INSTALLER finger
Administrator programming block diagram
11. INSTALLER PROGRAMMING
Set relay 1 time
Set relay 2 time
BUZZER ON/OFF
BACKLIGHT ON/OFF
Installer programming block diagram
3
3
4
4
4
4
5
5
6
6
6
6
7
7
7
7
7
8
8
8
9
10
10
10
10
10
11
CONTENTS
1. INTRODUCTION
2. MOUNTING
3. SPECIFICATIONS
4. APPLICATION DIAGRAM
5. RECOMMENDED SWIPING TECHNIQUE
6. INDICATION
7. WIRING
8. ADDING ADMIN FINGER
9. PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT
Pairing B100-SA v2 with DINRTT
Pairing B100-SA v2 with RTT
Pairing B100-SA v2 with RU2
10. ADMINISTRATOR PROGRAMMING
ADD finger relay 1
ADD finger relay 2
ADD finger relay 1&2
DELETE finger
DELETE ALL fingers
CHANGE ADMIN finger
CHANGE INSTALLER finger
Administrator programming block diagram
11. INSTALLER PROGRAMMING
Set relay 1 time
Set relay 2 time
BUZZER ON/OFF
BACKLIGHT ON/OFF
Installer programming block diagram
3
3
4
4
4
4
5
5
6
6
6
6
7
7
7
7
7
8
8
8
9
10
10
10
10
10
11
CONTENTS
www.xprgroup.com3
1. INTRODUCTION
MAINTENANCE
WARNING!
2. MOUNTING
RECOMMENDATIONS
NOTES
B100-SA v2 is access control fingerprint reader designed for easy management of the users and configuration. The
scanner is made with advanced capacitive sensing technology that provides some advantages over optical solutions like:
- making almost impossible to make fake copy of the users fingers
- same performance in the different light conditions
- good reading of fingers with stains from daily jobs
Built in strong scanning and matching algorithm provides excellent tolerance in the way finger is swiped over the sensor
reducing to minimum the need to repeat finger swiping at the sensor.
The reader can store up to 100 finger templates. One template is reserved for User manager (Administrator), one
template is reserved for Reader configuration (Installer) and up to 98 templates are for Users.
No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use
chemicals and materials that can scratch the sensor.
Do not touch the sensor with other objects than finger. Do not pour or splash with water or other liquids. When painting or
construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint.
If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled
according to all national laws and regulations.
Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can
increase the security of the system if needed. One or two enrolled fingers are enough for one user. Ask the installer before he
leaves the site to enroll your finger as administrator.
The Reader is using physical roughness of the fingerprint to scan the finger. Some of the users may have very flat fingertips,
making difficult for the sensor to recognize correctly the fingerprint. In most cases, these are children and older persons. To
solve this problem, do the following:
1. Try with different user’s fingers to find the “best” finger.
2. Check with the installer other models of the reader with added card reader or keypad for other type of access.
Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna.
Do not place the device near or above heating equipments.
If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.
Do not let children touch the device without supervision.
Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the fingerprint can’t be entered.
The operating temperature of the product is between 0ºC - + 50ºC. XPR™ cannot guarantee the functionality of the product if
measures and advice before are not followed.
1. INTRODUCTION
MAINTENANCE
WARNING!
2. MOUNTING
RECOMMENDATIONS
NOTES
B100-SA v2 is access control fingerprint reader designed for easy management of the users and configuration. The
scanner is made with advanced capacitive sensing technology that provides some advantages over optical solutions like:
- making almost impossible to make fake copy of the users fingers
- same performance in the different light conditions
- good reading of fingers with stains from daily jobs
Built in strong scanning and matching algorithm provides excellent tolerance in the way finger is swiped over the sensor
reducing to minimum the need to repeat finger swiping at the sensor.
The reader can store up to 100 finger templates. One template is reserved for User manager (Administrator), one
template is reserved for Reader configuration (Installer) and up to 98 templates are for Users.
No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use
chemicals and materials that can scratch the sensor.
Do not touch the sensor with other objects than finger. Do not pour or splash with water or other liquids. When painting or
construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint.
If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled
according to all national laws and regulations.
Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can
increase the security of the system if needed. One or two enrolled fingers are enough for one user. Ask the installer before he
leaves the site to enroll your finger as administrator.
The Reader is using physical roughness of the fingerprint to scan the finger. Some of the users may have very flat fingertips,
making difficult for the sensor to recognize correctly the fingerprint. In most cases, these are children and older persons. To
solve this problem, do the following:
1. Try with different user’s fingers to find the “best” finger.
2. Check with the installer other models of the reader with added card reader or keypad for other type of access.
Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna.
Do not place the device near or above heating equipments.
If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.
Do not let children touch the device without supervision.
Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the fingerprint can’t be entered.
The operating temperature of the product is between 0ºC - + 50ºC. XPR™ cannot guarantee the functionality of the product if
measures and advice before are not followed.
www.xprgroup.com4
4. APPLICATION DIAGRAM
6. INDICATION
3. SPECIFICATIONS
5. RECOMMENDED SWIPING TECHNIQUE
Fingerprint Capacity:
Output:
Push Button Input:
Panel Connection:
Door Open Time:
Entry Mode:
Programming:
Admin/Installer Fingers:
Backlight ON/OFF:
Buzzer ON/OFF:
Firmware upgrade:
Current Consumption:
Power Supply:
Indication:
IP Factor:
Operating Temperature:
Operating Humidity:
Dimensions(mm):
98 templates
1 x Relay (2 A /24V AC/DC)
Yes
Cable, 0.5 m
Pulse (1 to 30 seconds) or Toggle (ON/OFF)
Finger
By swiping
1 Administrator and 1 Installer Finger
Yes
Yes
via RS-485 converter and windows application
100 mA max.
9-14 V DC
Tricolor Status LED
IP54 (internal use only)
0°C to +50°C
5% to 95% RH without condensation
92 x 51 x 25 (metal); 92 x 51 x 27 (ABS)
Follow the below instructions for correct finger swiping. Starting from the first finger joint,
place the selected finger on the swipe sensor and move it evenly towards oneself in one
steady movement.
Result:
For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep)
For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps)
Unsecured Area
4. APPLICATION DIAGRAM
6. INDICATION
3. SPECIFICATIONS
5. RECOMMENDED SWIPING TECHNIQUE
Fingerprint Capacity:
Output:
Push Button Input:
Panel Connection:
Door Open Time:
Entry Mode:
Programming:
Admin/Installer Fingers:
Backlight ON/OFF:
Buzzer ON/OFF:
Firmware upgrade:
Current Consumption:
Power Supply:
Indication:
IP Factor:
Operating Temperature:
Operating Humidity:
Dimensions(mm):
98 templates
1 x Relay (2 A /24V AC/DC)
Yes
Cable, 0.5 m
Pulse (1 to 30 seconds) or Toggle (ON/OFF)
Finger
By swiping
1 Administrator and 1 Installer Finger
Yes
Yes
via RS-485 converter and windows application
100 mA max.
9-14 V DC
Tricolor Status LED
IP54 (internal use only)
0°C to +50°C
5% to 95% RH without condensation
92 x 51 x 25 (metal); 92 x 51 x 27 (ABS)
Follow the below instructions for correct finger swiping. Starting from the first finger joint,
place the selected finger on the swipe sensor and move it evenly towards oneself in one
steady movement.
Result:
For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep)
For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps)
Unsecured Area
5
6
7
8
9
10
11
12
advertisement
Key Features
- Fingerprint access control
- Standalone operation
- Capacitive sensing technology
- Up to 100 user templates
- Administrator and Installer profiles
- Adjustable relay timings
- Programming options
Related manuals
Frequently Answers and Questions
How do I add a new user to the B100-SA reader?
To add a new user, you need to first swipe the Administrator finger, then wait for the backlight to blink fast, and then swipe the user's finger at least 6 times until you hear a short and long beep.
What is the difference between the Administrator and Installer fingers?
The Administrator finger is used to manage user access and perform administrative tasks. The Installer finger is used to configure the reader settings, such as relay timings and buzzer settings.
Can I pair the B100-SA reader with a remote relay unit?
Yes, you can pair the B100-SA reader with different remote relay units such as DINRTT, RTT and RU2. Refer to the Remote Relay's Manual for specific pairing instructions.
advertisement
