xpr WS4-CNV Manuel du propriétaire
publicité
www.xprgroup.com1
Wiegand to RS-485 Converter
WS4-CONV-V2
1. DESCRIPTION
2. SPECIFICATIONS
3. DIP SWITCH AND TERMINAL BLOCKS DESCRIPTION
EN
USER’S MANUAL
This converter allows the connection of any type of reader (Wiegand, Data / Clock ISO2, Dallas and RS-232) to the
local bus of the access units. The converter automatically adapts its inputs (D1/CLK/Dal and D0/DTA/Rx) to the reader’s
output.
• Current consumption without external elements: 30 mA
• Output 13,8 Vdc: max. 300 mA
• Tamper input
• Dimensions (mm): 54 x 30
TA
LedG
GND
Buz
D-
D1/DTA/Rx - Wiegand: DO & D1
- ISO2: CLK & DTA
- Dallas: DAL
- CodeB: Rx (9600
BPS)
Reader LED’s configuration
In order to configure the LED’s of your reader, check your reader manual and set the DIP Switch following the table
below:
D+
D0/CLK/DAL
12Vin
+12V
GND
GND
LedR
Rev. 1.02 - 13.01.2023
Legend
Z: Three state
LO: 0 volt
HI: +5 volts
Readers LED colors Orange Red Green OFF
DIP
Switch
position
Type LedR LedG LedR LedG LedR LedG LedR LedG
/ / / Z / Z / Z / Z
DIP 4 1 Wire / Z / LO / HI / Z
DIP 3 1 Wire / Z / HI / LO / Z
DIP 3 & 4 2 Wires LO LO LO Z Z LO Z Z
DIP 2 2 Wires LO LO Z LO LO Z Z Z
DIP 2 & 4 2 Wires Z Z Z LO LO Z LO LO
DIP 2 & 3 2 Wires Z Z LO Z Z LO LO LO
DIP
2, 3 & 4 2 Wires HI HI HI Z Z HI Z Z
DIP 1 2 Wires HI HI Z HI HI Z Z Z
DIP 1 & 4 2 Wires Z Z Z HI HI Z HI HI
DIP 1 & 3 2 Wires Z Z HI Z Z HI HI HI
Wiegand to RS-485 Converter
WS4-CONV-V2
1. DESCRIPTION
2. SPECIFICATIONS
3. DIP SWITCH AND TERMINAL BLOCKS DESCRIPTION
EN
USER’S MANUAL
This converter allows the connection of any type of reader (Wiegand, Data / Clock ISO2, Dallas and RS-232) to the
local bus of the access units. The converter automatically adapts its inputs (D1/CLK/Dal and D0/DTA/Rx) to the reader’s
output.
• Current consumption without external elements: 30 mA
• Output 13,8 Vdc: max. 300 mA
• Tamper input
• Dimensions (mm): 54 x 30
TA
LedG
GND
Buz
D-
D1/DTA/Rx - Wiegand: DO & D1
- ISO2: CLK & DTA
- Dallas: DAL
- CodeB: Rx (9600
BPS)
Reader LED’s configuration
In order to configure the LED’s of your reader, check your reader manual and set the DIP Switch following the table
below:
D+
D0/CLK/DAL
12Vin
+12V
GND
GND
LedR
Rev. 1.02 - 13.01.2023
Legend
Z: Three state
LO: 0 volt
HI: +5 volts
Readers LED colors Orange Red Green OFF
DIP
Switch
position
Type LedR LedG LedR LedG LedR LedG LedR LedG
/ / / Z / Z / Z / Z
DIP 4 1 Wire / Z / LO / HI / Z
DIP 3 1 Wire / Z / HI / LO / Z
DIP 3 & 4 2 Wires LO LO LO Z Z LO Z Z
DIP 2 2 Wires LO LO Z LO LO Z Z Z
DIP 2 & 4 2 Wires Z Z Z LO LO Z LO LO
DIP 2 & 3 2 Wires Z Z LO Z Z LO LO LO
DIP
2, 3 & 4 2 Wires HI HI HI Z Z HI Z Z
DIP 1 2 Wires HI HI Z HI HI Z Z Z
DIP 1 & 4 2 Wires Z Z Z HI HI Z HI HI
DIP 1 & 3 2 Wires Z Z HI Z Z HI HI HI
www.xprgroup.com2
4. CONNECTION DIAGRAM
Wiegand
Reader
WS4-CONV-V2
Wiegand to RS-485 converter
• Set the desired Wiegand Output of the reader.
• Connect the Wiegand Reader to the converter as shown in the picture above.
• Put the Address DIP Switch in the converter to the desired address, 0 or 1.
• Set the parameters for the reader in the WS4 software.
• DIP switch 7 On:
Wiegand mode: disables the possibility to use a Wiegand keypad.
• DIP switch 7 Off:
Wiegand mode: a Wiegand keypad can be used on the D0/D1 input;
The keypad must be configured in Single Key - 8 bits Wiegand - Nibbles Complemented.
• DIP switch 8 On: Address 0.
• DIP switch 8 Off: Address 1.
From version 2.03!!!
4. CONNECTION DIAGRAM
Wiegand
Reader
WS4-CONV-V2
Wiegand to RS-485 converter
• Set the desired Wiegand Output of the reader.
• Connect the Wiegand Reader to the converter as shown in the picture above.
• Put the Address DIP Switch in the converter to the desired address, 0 or 1.
• Set the parameters for the reader in the WS4 software.
• DIP switch 7 On:
Wiegand mode: disables the possibility to use a Wiegand keypad.
• DIP switch 7 Off:
Wiegand mode: a Wiegand keypad can be used on the D0/D1 input;
The keypad must be configured in Single Key - 8 bits Wiegand - Nibbles Complemented.
• DIP switch 8 On: Address 0.
• DIP switch 8 Off: Address 1.
From version 2.03!!!
www.xprgroup.com3
5. SOFTWARE SETTINGS
5.1 WIEGAND 26 BIT
5.2 WIEGAND 32 BIT
• In the Settings/Configuration of the readers select ”Wiegand 26bit”, the one shown in the picture below.
• In the Doors/Reader/Card tab select “Wiegand (decoded)”.
• In the Settings/Configuration of the reader select ”Wiegand 32bit RAW”, the one shown in the picture below.
• In the Doors/Reader/Card tab select “Wiegand (decoded)”.
This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive 2015/863/EU.
5. SOFTWARE SETTINGS
5.1 WIEGAND 26 BIT
5.2 WIEGAND 32 BIT
• In the Settings/Configuration of the readers select ”Wiegand 26bit”, the one shown in the picture below.
• In the Doors/Reader/Card tab select “Wiegand (decoded)”.
• In the Settings/Configuration of the reader select ”Wiegand 32bit RAW”, the one shown in the picture below.
• In the Doors/Reader/Card tab select “Wiegand (decoded)”.
This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive 2015/863/EU.
www.xprgroup.com4
Légende
Z: Haute impédance/
three state
LO: 0 volt
HI: +5 volts
Convertisseur Wiegand à RS-485
WS4-CONV-V2 FR
MANUEL DE L’UTILISATEUR
1. DESCRIPTION
2. CARACTÉRISTIQUES
3. DESCRIPTIONS DES COMMUTATEUR DIP ET DES BORNIERS
Ce convertisseur permet de connecter n’importe quel type de lecteur (Wiegand, Data/Clock ISO2, Dallas et RS-232)
au bus local des unités d’accès. Ce convertisseur adapte automatiquement ses entrées (D1/CLK/Dal et D0/DTA/Rx) à la
sortie du lecteur.
• Consommation de courant sans éléments externes: 30 mA
• Tension de sortie de 13,8 V CC: max. 300 mA
• Entrée anti-sabotage
• Dimensions (mm): 54 x 30
TA
LedG
GND
Buz
D-
D1/DTA/Rx - Wiegand: DO & D1
- ISO2: CLK & DTA
- Dallas: DAL
- CodeB: Rx (9600
BPS)
Réglage des LED du lecteur
Pour régler le comportement des LED, consultez le manuel du lecteur et réglez les commutateur DIP selon le tableau
ci-dessous.
D+
D0/CLK/DAL
12Vin
+12V
GND
GND
LedR
Couleur des LED
du lecteur Orange Rouge Vert ÉTEINTE
Positions des
commutateur
DIP
Type LedR LedG LedR LedG LedR LedG LedR LedG
/ / / Z / Z / Z / Z
DIP 4 1 Fil / Z / LO / HI / Z
DIP 3 1 Fil / Z / HI / LO / Z
DIP 3 & 4 2 Fils LO LO LO Z Z LO Z Z
DIP 2 2 Fils LO LO Z LO LO Z Z Z
DIP 2 & 4 2 Fils Z Z Z LO LO Z LO LO
DIP 2 & 3 2 Fils Z Z LO Z Z LO LO LO
DIP 2, 3 & 4 2 Fils HI HI HI Z Z HI Z Z
DIP 1 2 Fils HI HI Z HI HI Z Z Z
DIP 1 & 4 2 Fils Z Z Z HI HI Z HI HI
DIP 1 & 3 2 Fils Z Z HI Z Z HI HI HI
Légende
Z: Haute impédance/
three state
LO: 0 volt
HI: +5 volts
Convertisseur Wiegand à RS-485
WS4-CONV-V2 FR
MANUEL DE L’UTILISATEUR
1. DESCRIPTION
2. CARACTÉRISTIQUES
3. DESCRIPTIONS DES COMMUTATEUR DIP ET DES BORNIERS
Ce convertisseur permet de connecter n’importe quel type de lecteur (Wiegand, Data/Clock ISO2, Dallas et RS-232)
au bus local des unités d’accès. Ce convertisseur adapte automatiquement ses entrées (D1/CLK/Dal et D0/DTA/Rx) à la
sortie du lecteur.
• Consommation de courant sans éléments externes: 30 mA
• Tension de sortie de 13,8 V CC: max. 300 mA
• Entrée anti-sabotage
• Dimensions (mm): 54 x 30
TA
LedG
GND
Buz
D-
D1/DTA/Rx - Wiegand: DO & D1
- ISO2: CLK & DTA
- Dallas: DAL
- CodeB: Rx (9600
BPS)
Réglage des LED du lecteur
Pour régler le comportement des LED, consultez le manuel du lecteur et réglez les commutateur DIP selon le tableau
ci-dessous.
D+
D0/CLK/DAL
12Vin
+12V
GND
GND
LedR
Couleur des LED
du lecteur Orange Rouge Vert ÉTEINTE
Positions des
commutateur
DIP
Type LedR LedG LedR LedG LedR LedG LedR LedG
/ / / Z / Z / Z / Z
DIP 4 1 Fil / Z / LO / HI / Z
DIP 3 1 Fil / Z / HI / LO / Z
DIP 3 & 4 2 Fils LO LO LO Z Z LO Z Z
DIP 2 2 Fils LO LO Z LO LO Z Z Z
DIP 2 & 4 2 Fils Z Z Z LO LO Z LO LO
DIP 2 & 3 2 Fils Z Z LO Z Z LO LO LO
DIP 2, 3 & 4 2 Fils HI HI HI Z Z HI Z Z
DIP 1 2 Fils HI HI Z HI HI Z Z Z
DIP 1 & 4 2 Fils Z Z Z HI HI Z HI HI
DIP 1 & 3 2 Fils Z Z HI Z Z HI HI HI
5
6
7
8
9
10
11
12
13
14
15
16
17
18
publicité
Manuels associés
publicité
