Solas ONE6 Wall-Mount Instructions
Solas ONE6 Wall-Mount is a direct-vent gas fireplace, designed for Solás models SL-16N and SL-16P. It utilizes birch log set with lava rock media for a realistic fire experience. The fireplace is installed and operated according to the manufacturer's instructions and all applicable codes and requirements. This manual guides you step-by-step through the installation of the birch log set, including the removal and replacement of the burner.
advertisement
solasfires.com1
ONE6
DIRECT-VENT LOG SET KIT
PART: LGS-16
INSTALLATION MANUAL
ONLY FOR USE ON SÓLAS MODELS: SL-16N, SL-16P
WARNING
This log set kit shall be installed by a qualified service agency in
accordance with the manufacturer’s instructions and all applicable
codes and requirements of the Authority Having Jurisdiction. If
the information in these instructions is not followed exactly, a fire,
explosion or production of carbon monoxide may result causing
property damage, personal injury or loss of life. The qualified
service agency is responsible for the proper installation of this kit.
The installation is not proper and complete until the operation of the
converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.
NOT FOR USE WITH VENT-FREE OR OUTDOOR FIREPLACES
SÓLAS BIRCH LOG SET KIT
INSTALLER: Leave this manual with appliance | CONSUMER: Retain this manual for future reference
ONE6
DIRECT-VENT LOG SET KIT
PART: LGS-16
INSTALLATION MANUAL
ONLY FOR USE ON SÓLAS MODELS: SL-16N, SL-16P
WARNING
This log set kit shall be installed by a qualified service agency in
accordance with the manufacturer’s instructions and all applicable
codes and requirements of the Authority Having Jurisdiction. If
the information in these instructions is not followed exactly, a fire,
explosion or production of carbon monoxide may result causing
property damage, personal injury or loss of life. The qualified
service agency is responsible for the proper installation of this kit.
The installation is not proper and complete until the operation of the
converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.
NOT FOR USE WITH VENT-FREE OR OUTDOOR FIREPLACES
SÓLAS BIRCH LOG SET KIT
INSTALLER: Leave this manual with appliance | CONSUMER: Retain this manual for future reference
SÓLAS CONTEMPORARY FIRE2
KIT CONTENTS:
• (1) CERAMIC LOGS • 7oz. LAVA ROCK
• (1) CERAMIC ROCKS • METAL LOG SET BURNER
LOG SET INSTALLATION
SÓLAS BIRCH LOG SET
BURNER SUPPORT LOCATIONS
Unless the ONE6 Direct-Vent Gas Fireplace was originally ordered with the Birch Log Set, your
fireplace will have shipped from the factory with a Glass Media burner in place. Before installing the
log set burner, you will need to remove the glass burner. See following steps 1-4 to remove the Glass
Media burner. If the fireplace has been ordered with the Log Set Burner, you can skip to
Step 10 (Page 4 of this manual).
1. The burner is held in place by 4 sheet metal screws, 2
on the left and 2 on the right. To make access to these
screws easier, we are going to loosen the valve bracket
so it can be moved slightly. Figure 1 shows the screw
on the left under side of the firebox securing the back
of the valve bracket, remove this screw. Keep this screw
in a safe place as it will be needed to secure the valve
bracket again once the logset burner is installed.
REMOVAL OF GLASS MEDIA BURNER
Figure 1
KIT CONTENTS:
• (1) CERAMIC LOGS • 7oz. LAVA ROCK
• (1) CERAMIC ROCKS • METAL LOG SET BURNER
LOG SET INSTALLATION
SÓLAS BIRCH LOG SET
BURNER SUPPORT LOCATIONS
Unless the ONE6 Direct-Vent Gas Fireplace was originally ordered with the Birch Log Set, your
fireplace will have shipped from the factory with a Glass Media burner in place. Before installing the
log set burner, you will need to remove the glass burner. See following steps 1-4 to remove the Glass
Media burner. If the fireplace has been ordered with the Log Set Burner, you can skip to
Step 10 (Page 4 of this manual).
1. The burner is held in place by 4 sheet metal screws, 2
on the left and 2 on the right. To make access to these
screws easier, we are going to loosen the valve bracket
so it can be moved slightly. Figure 1 shows the screw
on the left under side of the firebox securing the back
of the valve bracket, remove this screw. Keep this screw
in a safe place as it will be needed to secure the valve
bracket again once the logset burner is installed.
REMOVAL OF GLASS MEDIA BURNER
Figure 1
solasfires.com3
LOG SET INSTALLATION
2. Figure 2 shows the screw on the right underside of
the firebox which secures the front of the valve bracket,
remove this screw. Keep this screw in a safe place a
it will be needed to secure the valve bracket again
once the logset burner is installed.
3. The valve bracket is still secured by a third screw,
without removing this screw, the valve bracket and
valve can be pulled down approximately ½” (12mm)
as shown in Figure 3.
4. The burner is held in place by 4 sheet metal screws,
2 on the left and 2 on the right. Figure 4 shows 2
screws on the left under side of the firebox, remove
these screws. Keep these screws in a safe place as
they will be needed to install the Log Set burner.
5. Figure 5 shows the 2 screws on the right underside of
the firebox, remove these screws. A 5/16”, 6” or longer nut
driver will make removal of these screws easier. Keep
these screws in a safe place as they will be needed to
install the Logset burner.
6. To remove the burner from the fireplace, slide the
entire assembly to the right before lifting up to
remove as shown in Figure 6.
7. Once the glass media burner has been removed,
locate the Logset burner included in the kit LGS-16
as shown below in Figure 7.
Figure 3
Figure 4
Figure 2 Figure 5
Figure 6
Figure 7
LOG SET INSTALLATION
2. Figure 2 shows the screw on the right underside of
the firebox which secures the front of the valve bracket,
remove this screw. Keep this screw in a safe place a
it will be needed to secure the valve bracket again
once the logset burner is installed.
3. The valve bracket is still secured by a third screw,
without removing this screw, the valve bracket and
valve can be pulled down approximately ½” (12mm)
as shown in Figure 3.
4. The burner is held in place by 4 sheet metal screws,
2 on the left and 2 on the right. Figure 4 shows 2
screws on the left under side of the firebox, remove
these screws. Keep these screws in a safe place as
they will be needed to install the Log Set burner.
5. Figure 5 shows the 2 screws on the right underside of
the firebox, remove these screws. A 5/16”, 6” or longer nut
driver will make removal of these screws easier. Keep
these screws in a safe place as they will be needed to
install the Logset burner.
6. To remove the burner from the fireplace, slide the
entire assembly to the right before lifting up to
remove as shown in Figure 6.
7. Once the glass media burner has been removed,
locate the Logset burner included in the kit LGS-16
as shown below in Figure 7.
Figure 3
Figure 4
Figure 2 Figure 5
Figure 6
Figure 7
SÓLAS CONTEMPORARY FIRE4
LOG SET INSTALLATION
STEP 1
Install the logset burner within the firebox by lowering
the burner into the firebox (while keeping the burner
pressed toward the right side of the firebox) then
sliding the burner left towards the center of the firebox
to engage the burner orifice as shown in figure 10.
Confirm that the burner inlet tube has engaged the
burner orifice. (Figure 10)
STEP 2
Secure the burner using the (4) #10 sheet metal screws
set aside from steps 4 & 5
STEP 3
Secure the valve bracket using the (2) #10 sheet metal
screws set aside from steps 1 & 2.
STEP 4
Install the 3-rock cluster on the 2 pins located just right
of the pilot. (Figure 11)
Figure 10
Figure 11
> Start HERE if the ONE6 Wall-Mount was originally ordered with a Log Set Burner
NOTE: The log set burner can be configured for either
Natural Gas or Propane by installing or removing a collar
on the burner venturi. Figure 8 shows the venturi inlet with
the collar installed on a burner configured for Natural Gas.
Figure 9 shows the venturi inlet with the collar removed
from a burner configured for Propane. THIS VENTURI IS
NOT ADJUSTABLE. If you need to convert your burner
from Propane to Natural Gas or vice-versa, please order
the appropriate conversion kit for your appliance.
INTALLATION OF BIRCH LOG SET
Collar OFF for LP Collar ON for NG
Figure 8 Figure 9
LOG SET INSTALLATION
STEP 1
Install the logset burner within the firebox by lowering
the burner into the firebox (while keeping the burner
pressed toward the right side of the firebox) then
sliding the burner left towards the center of the firebox
to engage the burner orifice as shown in figure 10.
Confirm that the burner inlet tube has engaged the
burner orifice. (Figure 10)
STEP 2
Secure the burner using the (4) #10 sheet metal screws
set aside from steps 4 & 5
STEP 3
Secure the valve bracket using the (2) #10 sheet metal
screws set aside from steps 1 & 2.
STEP 4
Install the 3-rock cluster on the 2 pins located just right
of the pilot. (Figure 11)
Figure 10
Figure 11
> Start HERE if the ONE6 Wall-Mount was originally ordered with a Log Set Burner
NOTE: The log set burner can be configured for either
Natural Gas or Propane by installing or removing a collar
on the burner venturi. Figure 8 shows the venturi inlet with
the collar installed on a burner configured for Natural Gas.
Figure 9 shows the venturi inlet with the collar removed
from a burner configured for Propane. THIS VENTURI IS
NOT ADJUSTABLE. If you need to convert your burner
from Propane to Natural Gas or vice-versa, please order
the appropriate conversion kit for your appliance.
INTALLATION OF BIRCH LOG SET
Collar OFF for LP Collar ON for NG
Figure 8 Figure 9
5
6
advertisement
Key Features
- Direct-vent
- Birch log set
- Lava rock media
- Solás models SL-16N, SL-16P
- Installation manual
- Safety instructions
- Burner removal/installation
- Log set installation
Related manuals
Frequently Answers and Questions
How do I remove the glass media burner?
Follow steps 1-4 in the manual to remove the glass media burner, which is held in place by 4 sheet metal screws and a valve bracket. You will need to loosen the valve bracket first and then remove the burner.
How do I install the log set burner?
Refer to Step 1 in the “INSTALLATION OF BIRCH LOG SET” section. Ensure the burner orifice is engaged and secure it with the provided screws.
What type of gas is this appliance compatible with?
The log set burner can be configured for either Natural Gas or Propane by installing or removing a collar on the burner venturi. See Figure 8 and 9 for details. To convert from Propane to Natural Gas, or vice versa, you will need to order the appropriate conversion kit.
Is this manual for vent-free or outdoor fireplaces?
No, this manual is specifically for Solas ONE6 Direct-Vent Gas Fireplace models SL-16N and SL-16P. It is not compatible with vent-free or outdoor fireplaces.
advertisement
