Noark Ex9S32 Instruction Booklet
Noark Ex9S32 is a manual self-protected combination motor controller designed for use with various motor starter applications. It features multiple auxiliary contact options, including ASNB, ASNF, ASNUV, and SHT51, allowing for flexible control and monitoring capabilities. The Ex9S32 also offers fault indicating contact (AL51) and shunt release (SHT51) for enhanced safety and reliability. It is designed to be user-friendly with easy installation and removal instructions.
advertisement
Z9S32201912NA
Ex9S32 Manual Motor Starter Manual Self-Protected
Combination Motor Controller
Current setting
max.
min.
Trip test
Test
≤Φ5mm
Function Instruction
AX51
Ex9S32
AX52
AL51 UVT51
SHT51
At most two
At most one
At most one
At most one
At most one
or
CCT51
AX51
3 4
AX52
3
Mounting of
Instruction
14～10 AWG14～8 AWG
CCT51
AX51,AX52,AL51
UVT51,SHT51
2.5～16mm2
18～12 AWG
1～2.5mm2
18～12 AWG
1～2.5mm2
18～8 AWG
1～10mm2
18～12 AWG
1～2.5mm2
18～8 AWG
1～10mm2
18～12 AWG
1～2.5mm2
14～8 AWG
18～12 AWG
1～2.5mm2
14～8 AWG
18～12 AWG
1～2.5mm2
M5
M3
CCT51
AX51,AX52,AL51
31 lb·in [3.5 N·m]
7 lb·in [0.8 N·m]
M3.5 15 lb·in [1.7 N·m]
Strip Length (a)
a
a
Torque
0.5 in [13 mm]
0.4 in [10 mm]
0.35 in [9 mm]
Ex9S32
UVT51,SHT51
M4 22 lb·in [2.5 N·m] 0.43 in [11 mm]
2.5～16mm2
Ex9S32 2.5～10mm2
14～6 AWG 14～6 AWG
— —
— —
—
—
—
—
Screw
SHT51 or UVT51
Attention:
Accessories can be
installed when Ex9S32
in OFF position.
Attention:
Turn off power supplying
before installation, removal
or adjustment of the products
and accessories.
Attention:
Ex9S32 should not be closed
in step 4 when installing UVT51,
otherwise please reinstall UVT51.
The inching signal which controls
SHT51 should last within 8 seconds.
3
4
or
4
2.5～6mm2 2.5～10mm2 2.5～10mm2
CCE51
or
ASNB
ASNT
ASNUV
ASNF
辅助触头 Auxiliary contact
分励脱扣器 Shunt release
AX51
AX52
AL51
SHT51
UVT51
Auxiliary Contact front mount only
Auxiliary Contact left side only
Fault Indicating Contact left side only
Shunt Release right side only
Undervoltage Release right side only
CCT51 / CCE51 Terminal Adapter line side
Ex9S32 Manual Motor Starter Manual Self-Protected
Combination Motor Controller
Current setting
max.
min.
Trip test
Test
≤Φ5mm
Function Instruction
AX51
Ex9S32
AX52
AL51 UVT51
SHT51
At most two
At most one
At most one
At most one
At most one
or
CCT51
AX51
3 4
AX52
3
Mounting of
Instruction
14～10 AWG14～8 AWG
CCT51
AX51,AX52,AL51
UVT51,SHT51
2.5～16mm2
18～12 AWG
1～2.5mm2
18～12 AWG
1～2.5mm2
18～8 AWG
1～10mm2
18～12 AWG
1～2.5mm2
18～8 AWG
1～10mm2
18～12 AWG
1～2.5mm2
14～8 AWG
18～12 AWG
1～2.5mm2
14～8 AWG
18～12 AWG
1～2.5mm2
M5
M3
CCT51
AX51,AX52,AL51
31 lb·in [3.5 N·m]
7 lb·in [0.8 N·m]
M3.5 15 lb·in [1.7 N·m]
Strip Length (a)
a
a
Torque
0.5 in [13 mm]
0.4 in [10 mm]
0.35 in [9 mm]
Ex9S32
UVT51,SHT51
M4 22 lb·in [2.5 N·m] 0.43 in [11 mm]
2.5～16mm2
Ex9S32 2.5～10mm2
14～6 AWG 14～6 AWG
— —
— —
—
—
—
—
Screw
SHT51 or UVT51
Attention:
Accessories can be
installed when Ex9S32
in OFF position.
Attention:
Turn off power supplying
before installation, removal
or adjustment of the products
and accessories.
Attention:
Ex9S32 should not be closed
in step 4 when installing UVT51,
otherwise please reinstall UVT51.
The inching signal which controls
SHT51 should last within 8 seconds.
3
4
or
4
2.5～6mm2 2.5～10mm2 2.5～10mm2
CCE51
or
ASNB
ASNT
ASNUV
ASNF
辅助触头 Auxiliary contact
分励脱扣器 Shunt release
AX51
AX52
AL51
SHT51
UVT51
Auxiliary Contact front mount only
Auxiliary Contact left side only
Fault Indicating Contact left side only
Shunt Release right side only
Undervoltage Release right side only
CCT51 / CCE51 Terminal Adapter line side
02/2020
To maintain overcurrent, short-circuit, and ground-fault protection,
the manufacturer's instructions for selection of overload and
short-circuit protection must be followed to reduce the risk of fire
or electric shock.
AVERTISSEMENT
Pour assurer une protection continue contre les surintensités, les
courts-circuits et les fuites à la terre, les instructions du fabricant
relatives à la sélection d'une protection contre la surcharge et les
courts-circuits doivent être respectées afin de réduire le risque
d'incendie et ou de choc électrique.
Installation
3
Removal
Device must be installed in an enclosure sized
460mm x 200mm x 140mm at a minimum.
Surrounding Air Temperature rating of 40°C.
When an overload or a fault current interruption occurs, circuits must
be checked to determine the cause of the interruption. When a fault
condition exists, the current-carrying components should be examined
and replaced when damaged, and the integral current sensors must
be replaced to reduce the risk of fire or electric shock.
AVERTISSEMENT
En cas d'intervention due à une surcharge ou un courant de défaut,
les circuits doivent être vérifiés pour déterminer la cause de
l'interruption. En condition de défaut, les composants porteurs de
courant devraient être examinés et remplacés au besoin, et les
capteurs de courant intégrés doivent être remplacés afin de réduire
le risqué d'incendie et ou de choc électrique.
AL51
4
3
Red
Short CircutReset
Over load fault
Red or
no colour
Short CircutReset
Short Circut fault
Green
Fault Indication and Reset
Red
90
90
120
30
Angle of Installation
Press
Push
Press
Lift Pull
Reset
4
Reset
o
o
o
o
To maintain overcurrent, short-circuit, and ground-fault protection,
the manufacturer's instructions for selection of overload and
short-circuit protection must be followed to reduce the risk of fire
or electric shock.
AVERTISSEMENT
Pour assurer une protection continue contre les surintensités, les
courts-circuits et les fuites à la terre, les instructions du fabricant
relatives à la sélection d'une protection contre la surcharge et les
courts-circuits doivent être respectées afin de réduire le risque
d'incendie et ou de choc électrique.
Installation
3
Removal
Device must be installed in an enclosure sized
460mm x 200mm x 140mm at a minimum.
Surrounding Air Temperature rating of 40°C.
When an overload or a fault current interruption occurs, circuits must
be checked to determine the cause of the interruption. When a fault
condition exists, the current-carrying components should be examined
and replaced when damaged, and the integral current sensors must
be replaced to reduce the risk of fire or electric shock.
AVERTISSEMENT
En cas d'intervention due à une surcharge ou un courant de défaut,
les circuits doivent être vérifiés pour déterminer la cause de
l'interruption. En condition de défaut, les composants porteurs de
courant devraient être examinés et remplacés au besoin, et les
capteurs de courant intégrés doivent être remplacés afin de réduire
le risqué d'incendie et ou de choc électrique.
AL51
4
3
Red
Short CircutReset
Over load fault
Red or
no colour
Short CircutReset
Short Circut fault
Green
Fault Indication and Reset
Red
90
90
120
30
Angle of Installation
Press
Push
Press
Lift Pull
Reset
4
Reset
o
o
o
o
advertisement
Key Features
- Manual self-protected
- Combination motor controller
- Auxiliary contacts
- Fault indicating contact
- Shunt release
- Easy installation
Related manuals
Frequently Answers and Questions
What types of auxiliary contacts are available for the Ex9S32?
The Ex9S32 offers ASNB, ASNF, ASNUV, and SHT51 auxiliary contacts. Each contact type has unique mounting positions and functions.
How do I reset the Ex9S32 after a fault?
To reset the Ex9S32 after a fault, follow these steps: 1. Identify the fault indication (red light on AL51). 2. Press the reset button on the AL51 contact. 3. Ensure power supply is restored to the device.
What is the maximum torque for the Ex9S32 terminals?
The maximum torque for Ex9S32 terminals varies depending on the screw size. For M5 screws, the maximum torque is 31 lb·in [3.5 N·m]. For M4 screws, the maximum torque is 22 lb·in [2.5 N·m].
advertisement