Allen-Bradley 1336 PLUS Custom Hardware - MX22 Installation Instructions
advertisement
Instructions
1336 PLUS Custom Hardware
MX22 - Solid State CR4 Digital Output
Description Custom Hardware MX22 differs from the standard 1336 PLUS drive in the
following way:
• Replacement of digital output relay CR4 on the main control board with
a solid state (open collector) relay. Terminal assignments, polarities, and
ratings have changed (see below).
Digital Outputs The digital outputs are at terminals 10 through 18 of TB2.
Figure 1 Digital Outputs – TB2
!
ATTENTION: This Custom Hardware has been designed for a
specific application and differs from the standard 1336 PLUS
product offering. It must be installed and run only under this
custom application. Attempting to run this Custom Hardware
under any other type of application or condition could result in
unpredictable and/or hazardous conditions.
!
ATTENTION: This drive contains ESD (Electrostatic
Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing or
repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with
static control procedures, reference A-B publication 8000-4.5.2,
“Guarding Against Electrostatic Damage” or any other applicable
ESD protection handbook.
Reserved for
Future Use
CR2CR1 CR3CR3 CR4
10 11 12 13 14 15 16 17 18 A1 A2
Terminal
10, 11
11, 12
13, 14
14, 15
16
17, 18
A1, A2
Signal
CR1 Programmable Contact
CR2 Programmable Contact
CR3 Programmable Contact
CR4 Programmable Contact
Reserved for Future Use
Resistive Rating = 115V AC/30V DC, 5.0A
Inductive Rating = 115V AC/30V DC, 2.0A
Contacts Shown in Unpowered State
(or Powered State with Fault/Alarm Present)
+ -
24VDC
ONLY
NC
Resistive Rating = 24VDC, 1.0A
No Connection
1336 PLUS Custom Hardware
MX22 - Solid State CR4 Digital Output
Description Custom Hardware MX22 differs from the standard 1336 PLUS drive in the
following way:
• Replacement of digital output relay CR4 on the main control board with
a solid state (open collector) relay. Terminal assignments, polarities, and
ratings have changed (see below).
Digital Outputs The digital outputs are at terminals 10 through 18 of TB2.
Figure 1 Digital Outputs – TB2
!
ATTENTION: This Custom Hardware has been designed for a
specific application and differs from the standard 1336 PLUS
product offering. It must be installed and run only under this
custom application. Attempting to run this Custom Hardware
under any other type of application or condition could result in
unpredictable and/or hazardous conditions.
!
ATTENTION: This drive contains ESD (Electrostatic
Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing or
repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with
static control procedures, reference A-B publication 8000-4.5.2,
“Guarding Against Electrostatic Damage” or any other applicable
ESD protection handbook.
Reserved for
Future Use
CR2CR1 CR3CR3 CR4
10 11 12 13 14 15 16 17 18 A1 A2
Terminal
10, 11
11, 12
13, 14
14, 15
16
17, 18
A1, A2
Signal
CR1 Programmable Contact
CR2 Programmable Contact
CR3 Programmable Contact
CR4 Programmable Contact
Reserved for Future Use
Resistive Rating = 115V AC/30V DC, 5.0A
Inductive Rating = 115V AC/30V DC, 2.0A
Contacts Shown in Unpowered State
(or Powered State with Fault/Alarm Present)
+ -
24VDC
ONLY
NC
Resistive Rating = 24VDC, 1.0A
No Connection
2 MX22 - Solid State CR4 Digital Output
Notes:
Publication 1336S-IN045A-EN-P Ð July, 2001 P/N 308446 (01)
Copyright © 2001 Rockwell Automation. All rights reserved. Printed in USA.
Notes:
Publication 1336S-IN045A-EN-P Ð July, 2001 P/N 308446 (01)
Copyright © 2001 Rockwell Automation. All rights reserved. Printed in USA.
advertisement
Related manuals
advertisement