Allen-Bradley 1329I CE Filter Option Kit Installation Instructions
advertisement
Instruction Sheet
1329I Integrated Drive/Motor
CE Filter Option Kit
CE filter options are designed to be used with the 1329I Integrated Drive/Motor.
The main function of the CE filter is to reduce the radio frequency conducted
emissions into the main supply lines and ground wiring. This publication
provides the steps needed to install the filter.
Important: Declarations of Conformity to the European Union Directives
are available for Allen-Bradley AC drive products. Please
contact your Allen-Bradley Sales Representative.
Refer to the page listed below for installation instructions.
• Internal Mount Option – See page 2.
• NEMA 12 Enclosed Option – See page 5.
ATTENTION: The CE filter connects between the incoming AC
supply line and the drive input terminals. The filter must be
installed by qualified personnel familiar with the drive and
associated machinery. Failure to comply may result in personal
injury and/or equipment damage.
ATTENTION: An incorrectly applied or installed CE filter can
result in component damage or a reduction in product life. Wiring
or application errors, such as incorrect wiring layout, incorrect or
inadequate AC supply or excessive ambient temperatures may
result in malfunction of the system.
1329I Integrated Drive/Motor
CE Filter Option Kit
CE filter options are designed to be used with the 1329I Integrated Drive/Motor.
The main function of the CE filter is to reduce the radio frequency conducted
emissions into the main supply lines and ground wiring. This publication
provides the steps needed to install the filter.
Important: Declarations of Conformity to the European Union Directives
are available for Allen-Bradley AC drive products. Please
contact your Allen-Bradley Sales Representative.
Refer to the page listed below for installation instructions.
• Internal Mount Option – See page 2.
• NEMA 12 Enclosed Option – See page 5.
ATTENTION: The CE filter connects between the incoming AC
supply line and the drive input terminals. The filter must be
installed by qualified personnel familiar with the drive and
associated machinery. Failure to comply may result in personal
injury and/or equipment damage.
ATTENTION: An incorrectly applied or installed CE filter can
result in component damage or a reduction in product life. Wiring
or application errors, such as incorrect wiring layout, incorrect or
inadequate AC supply or excessive ambient temperatures may
result in malfunction of the system.
2 1329I Integrated Drive/Motor CE Filter Option Kit
Internal Mount Installation Use the cross-reference table below to verify that the correct filter has been
selected for your CE compatible drive.
Filter Selection
Components Supplied
Filter Catalog
Number Series Ratings
Use with Bulletin 1329I
Series B Drive/Motor
1329I-NLF1 A 115/230 VAC
Single Phase
14 Amps
1329I-BJ
1329I-BK
1329I-NLF3 A 230/460 VAC
Three Phase
9 Amps
1329I-BL
1329I-BM
Item Quantity Supplied Quantity Required to Install
Screws
M4 × 8 TT
5 4
Lock Washers
M4 Internal Tooth
5 4
Internal Mount Installation Use the cross-reference table below to verify that the correct filter has been
selected for your CE compatible drive.
Filter Selection
Components Supplied
Filter Catalog
Number Series Ratings
Use with Bulletin 1329I
Series B Drive/Motor
1329I-NLF1 A 115/230 VAC
Single Phase
14 Amps
1329I-BJ
1329I-BK
1329I-NLF3 A 230/460 VAC
Three Phase
9 Amps
1329I-BL
1329I-BM
Item Quantity Supplied Quantity Required to Install
Screws
M4 × 8 TT
5 4
Lock Washers
M4 Internal Tooth
5 4
1329I Integrated Drive/Motor CE Filter Option Kit 3
Filter Installation
1. Remove the cover of the 1329I unit by loosening the four cover screws.
The display ribbon cable is designed to disconnect from the main unit
when the cover is removed.
2. Mount the CE filter as shown in the figure below using the screws
provided.
3. The CE filter must be connected between the incoming AC supply line
and the drive input terminals.
Important: The filter may cause ground leakage currents. Therefore, a solid
ground connection must be provided as shown on the following
page.
ATTENTION: To prevent electrical shock, disconnect the power
source before installing or servicing.
ATTENTION:After disconnecting input power wait five minutes
and check with voltmeter to assure that DC bus capacitors are
discharged (DC+, DC-). The voltmeter should read zero volts.
Failure to observe these precautions could result in severe bodily
injury or loss of life.
1.46 Nm
(13 in-lb)
2.6 Nm
(23 in-lb)
Filter Installation
1. Remove the cover of the 1329I unit by loosening the four cover screws.
The display ribbon cable is designed to disconnect from the main unit
when the cover is removed.
2. Mount the CE filter as shown in the figure below using the screws
provided.
3. The CE filter must be connected between the incoming AC supply line
and the drive input terminals.
Important: The filter may cause ground leakage currents. Therefore, a solid
ground connection must be provided as shown on the following
page.
ATTENTION: To prevent electrical shock, disconnect the power
source before installing or servicing.
ATTENTION:After disconnecting input power wait five minutes
and check with voltmeter to assure that DC bus capacitors are
discharged (DC+, DC-). The voltmeter should read zero volts.
Failure to observe these precautions could result in severe bodily
injury or loss of life.
1.46 Nm
(13 in-lb)
2.6 Nm
(23 in-lb)
4 1329I Integrated Drive/Motor CE Filter Option Kit
Filter Wiring
4. Connect wires as shown in the diagram below. (Three Phase unit shown.)
ATTENTION: To guard against possible equipment damage, RFI
filters can only be used with AC supplies that are nominally
balanced with respect to ground. In some installations, three-
phase supplies are occasionally connected in a 3-wire
configuration with one phase grounded (Grounded Delta). The
filter must not be used in Grounded Delta supplies.
Conduit/4-Wire Cable
Nearest Building Structure Steel
PE
1329I Integrated Drive Motor
L1IN
L2IN
L3IN W3OUT
W2
OUT
W1
OUT
T/L3
S/L2
R/L1
CE Filter
DC+
DC-
DBR
T/L3
S/L2
R/L1
PE
L3
L2
L1
1.3 Nm
(12 in-lb)
1.3 Nm
(12 in-lb)
Filter Wiring
4. Connect wires as shown in the diagram below. (Three Phase unit shown.)
ATTENTION: To guard against possible equipment damage, RFI
filters can only be used with AC supplies that are nominally
balanced with respect to ground. In some installations, three-
phase supplies are occasionally connected in a 3-wire
configuration with one phase grounded (Grounded Delta). The
filter must not be used in Grounded Delta supplies.
Conduit/4-Wire Cable
Nearest Building Structure Steel
PE
1329I Integrated Drive Motor
L1IN
L2IN
L3IN W3OUT
W2
OUT
W1
OUT
T/L3
S/L2
R/L1
CE Filter
DC+
DC-
DBR
T/L3
S/L2
R/L1
PE
L3
L2
L1
1.3 Nm
(12 in-lb)
1.3 Nm
(12 in-lb)
5
6
7
8
advertisement
Related manuals
advertisement