Allen-Bradley WebPak 3000 Installation Instructions
Allen-Bradley WebPak 3000 is an Operator Interface Module (OIM) kit designed to replace the built-in keypad and display on your drive. It allows you to easily change drive parameters, control operations, and monitor the drive's performance. The kit includes the OIM module itself, an instruction manual, and all necessary hardware for installation.
advertisement
©1999 Rockwell International Corporation
WebPak and Reliance are trademarks of Rockwell Automation.
WebPak 3000 Operator Interface Module (OIM) Kit
M/N 925WK0101
Instruction Manual D2-3461
Product Description
The WebPak 3000 Operator Interface Module ( OIM ) Kit is used to replace the drive’s built-in keypad and display.
The OIM enables you to change drive parameters, operate the drive, and monitor drive operation. The contents
of the kit are listed in table 1.
Preparing to Replace the OIM
Before replacing the OIM , disconnect power from the drive.
You will need the following tools:
• #1 Phillips screwdriver
• #2 Phillips screwdriver
• M7 Hex wrench or socket wrench
Accessing the OIM and Disconnecting It from the Regulator Board
Important: Unless otherwise indicated, keep all hardware for the replacement procedure.
Step 1. Loosen the screws that secure the front cover to the drive.
Step 2. Remove the front cover.
!
ATTENTION: Only qualified electrical personnel familiar with the construction and operation of
this equipment and the hazards involved should install, adjust, operate, or service this equipment.
Read and understand this manual in its entirety before proceeding. Failure to observe this
precaution could result in severe bodily injury or loss of life.
ATTENTION: Do not install or remove the OIM with power applied to the drive. Disconnect and
lockout incoming power before attempting installation or removal. Failure to observe this
precaution could result in severe bodily injury or loss of life.
Table 1 – Contents of the WebPak 3000 Operator Interface Module Kit
Description Quantity Part Number
Operator Interface Module 1 807313-2R
Instruction Manual 1 D2-3461
WebPak and Reliance are trademarks of Rockwell Automation.
WebPak 3000 Operator Interface Module (OIM) Kit
M/N 925WK0101
Instruction Manual D2-3461
Product Description
The WebPak 3000 Operator Interface Module ( OIM ) Kit is used to replace the drive’s built-in keypad and display.
The OIM enables you to change drive parameters, operate the drive, and monitor drive operation. The contents
of the kit are listed in table 1.
Preparing to Replace the OIM
Before replacing the OIM , disconnect power from the drive.
You will need the following tools:
• #1 Phillips screwdriver
• #2 Phillips screwdriver
• M7 Hex wrench or socket wrench
Accessing the OIM and Disconnecting It from the Regulator Board
Important: Unless otherwise indicated, keep all hardware for the replacement procedure.
Step 1. Loosen the screws that secure the front cover to the drive.
Step 2. Remove the front cover.
!
ATTENTION: Only qualified electrical personnel familiar with the construction and operation of
this equipment and the hazards involved should install, adjust, operate, or service this equipment.
Read and understand this manual in its entirety before proceeding. Failure to observe this
precaution could result in severe bodily injury or loss of life.
ATTENTION: Do not install or remove the OIM with power applied to the drive. Disconnect and
lockout incoming power before attempting installation or removal. Failure to observe this
precaution could result in severe bodily injury or loss of life.
Table 1 – Contents of the WebPak 3000 Operator Interface Module Kit
Description Quantity Part Number
Operator Interface Module 1 807313-2R
Instruction Manual 1 D2-3461
Publication D2-3461 - December 1999 1999 Rockwell International Corporation. All rights reserved. Printed in USA.
Step 3. Disconnect the communication cable from J9 on the Regulator board by pressing down the locking
clip and pulling the cable out.
Step 4. Remove the four screws holding the OIM assembly to the drive enclosure.
Step 5. Pull the OIM assembly away from the drive so you can access the ground wire on the upper right
corner of the OIM mounting plate. Slide the ground wire off its connection.
Important: Ground wires on older versions of the OIM are fastened by a nut. If you are replacing an older
version, keep the hardware so you can re-attach the ground wire.
Replacing the OIM
You must remove the old OIM assembly from the drive before replacing it. See “Preparing to Replace the OIM”,
and “Accessing the OIM and Disconnecting It from the Regulator Board” for instructions.
To replace the OIM :
Step 1. Connect the ground wire from the drive to the ground terminal on the OIM mounting plate. If you are
replacing an older version of the OIM , you might need to use the hardware from the old unit.
Step 2. Replace the four screws securing the OIM assembly to the drive.
Step 3. Connect the communication cable from the OIM assembly to J9 on the Regulator board, making sure
that it locks into place.
Step 4. Replace the drive front cover and tighten the screws, securing it to the drive enclosure.
Step 3. Disconnect the communication cable from J9 on the Regulator board by pressing down the locking
clip and pulling the cable out.
Step 4. Remove the four screws holding the OIM assembly to the drive enclosure.
Step 5. Pull the OIM assembly away from the drive so you can access the ground wire on the upper right
corner of the OIM mounting plate. Slide the ground wire off its connection.
Important: Ground wires on older versions of the OIM are fastened by a nut. If you are replacing an older
version, keep the hardware so you can re-attach the ground wire.
Replacing the OIM
You must remove the old OIM assembly from the drive before replacing it. See “Preparing to Replace the OIM”,
and “Accessing the OIM and Disconnecting It from the Regulator Board” for instructions.
To replace the OIM :
Step 1. Connect the ground wire from the drive to the ground terminal on the OIM mounting plate. If you are
replacing an older version of the OIM , you might need to use the hardware from the old unit.
Step 2. Replace the four screws securing the OIM assembly to the drive.
Step 3. Connect the communication cable from the OIM assembly to J9 on the Regulator board, making sure
that it locks into place.
Step 4. Replace the drive front cover and tighten the screws, securing it to the drive enclosure.
U.S. Drives Technical Support
Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: [email protected], Online: www.ab.com/support/abdrives
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication D2-3461- December 1999 Copyright © 1999 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: [email protected], Online: www.ab.com/support/abdrives
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication D2-3461- December 1999 Copyright © 1999 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
advertisement
Key Features
- Drive parameter control
- Drive operation control
- Drive monitoring
- Keypad and display replacement
- Easy installation
Related manuals
Frequently Answers and Questions
How do I disconnect the communication cable from the regulator board?
You need to press down the locking clip on the cable connector (J9) and pull it out. Refer to the 'Accessing the OIM and Disconnecting It from the Regulator Board' section in the viewed document for detailed instructions.
What tools are needed to replace the OIM?
You will need a #1 Phillips screwdriver, a #2 Phillips screwdriver, and an M7 Hex wrench or socket wrench. See the 'Preparing to Replace the OIM' section in the viewed document for more details.
Where can I find support for WebPak 3000 OIM?
You can contact U.S. Drives Technical Support via phone, fax, email, or online, as per the information provided in the viewed document.
advertisement