Allen-Bradley RAC6180 Display and Backlight Installation Instructions
Allen-Bradley RAC6180 Display and Backlight is a versatile display solution for industrial applications. It offers a range of sizes and features, including touchscreen options, for easy access to critical information. This display is designed for industrial environments, ensuring durability and reliable performance.
advertisement
(For 6180 Industrial Computers)
This instruction sheet describes how to replace the following
displays and backlights for 6180 Industrial Computers. All display
kits contain a hinge pin and 3 chassis latching screws.
Item See Page
10.4 Inch Bezel / Display 4
10.4 Inch Touchscreen / Display 4
11.3 Inch Bezel / Display 4
11.3 Inch Touchscreen Bezel / Display 4
Plastic Bezel No Display 4
Replacement Backlight (Catalog No. 6189-NL2)
10.4 Inch Display Only 2
The backlight uses Cold Cathode Fluorescent (CCF) tubes to
illuminate the display. The 11.3 inch displays have an integral
backlight that cannot be replaced separately, the entire bezel / display
must be replaced. The 10.4 inch backlight is replaceable.
!
ATTENTION: Disconnect all power from the 6180
Computer before replacing the backlight. Failure to
disconnect power may result in electrical shock and/or
damage to the terminal.
!
ATTENTION: Do not touch any of the exposed
electronic components to prevent damage from
electrostatic discharge (ESD).
Instructions
Applications
Overview & Safety
Display and Backlight2
To replace the backlight (10.4 inch displays only):
1. Disconnect the power from the 6180 Computer.
2. Remove the three latching screws that secure the chassis to the
front bezel
Front Bezel
Latching Screws (3)
3. Note the following precautions before swinging the chassis
away from the bezel.
!
ATTENTION: Remove all external cables from the
side panel connectors. Failure to remove cables may
cause damage to the cables and connectors.
!
ATTENTION: If the 6180 Computer is installed with
mounting clips, the mounting clips on the hinge side
will interfere with the opening of the hinge. Remove
the mounting clips on the hinge side before swinging
chassis away from the bezel. Failure to remove clips
may damage clips and the chassis.
4. Swing the chassis open about 90.
Replacing the 10.4 Inch
Display Backlight
To replace the backlight (10.4 inch displays only):
1. Disconnect the power from the 6180 Computer.
2. Remove the three latching screws that secure the chassis to the
front bezel
Front Bezel
Latching Screws (3)
3. Note the following precautions before swinging the chassis
away from the bezel.
!
ATTENTION: Remove all external cables from the
side panel connectors. Failure to remove cables may
cause damage to the cables and connectors.
!
ATTENTION: If the 6180 Computer is installed with
mounting clips, the mounting clips on the hinge side
will interfere with the opening of the hinge. Remove
the mounting clips on the hinge side before swinging
chassis away from the bezel. Failure to remove clips
may damage clips and the chassis.
4. Swing the chassis open about 90.
Replacing the 10.4 Inch
Display Backlight
Display and Backlight 3
Backlight
Power
Supply
Cable
(4) M4 Phillips Screws
5. Remove four screws that secure backlight and remove the
backlight to allow access to the power connector
6. Unplug the backlight power supply cable and remove the
backlight.
7. Plug the backlight power supply cable into the new backlight.
8. Place the backlight on the four backlight standoffs.
9. Replace the four backlight mounting screws and tighten to a
torque of 6 to 8 inch-pounds (.7 to .9 Nm).
10. Swing the chassis back into position and tighten the three latching
screws to a torque of 18 to 22 inch-pounds (2 to 2.5 Nm).
11. Reconnect and install any external cables or mounting clips.
12. Apply power and verify operation of the backlight.
Backlight
Power
Supply
Cable
(4) M4 Phillips Screws
5. Remove four screws that secure backlight and remove the
backlight to allow access to the power connector
6. Unplug the backlight power supply cable and remove the
backlight.
7. Plug the backlight power supply cable into the new backlight.
8. Place the backlight on the four backlight standoffs.
9. Replace the four backlight mounting screws and tighten to a
torque of 6 to 8 inch-pounds (.7 to .9 Nm).
10. Swing the chassis back into position and tighten the three latching
screws to a torque of 18 to 22 inch-pounds (2 to 2.5 Nm).
11. Reconnect and install any external cables or mounting clips.
12. Apply power and verify operation of the backlight.
Display and Backlight4
The procedures for replacing 11.3 and 10.4 inch bezel/displays are
the same. For purposes of illustration we show the 11.3 inch display.
If you are installing a bezel with no display, the procedures are the
same except for the number of electrical connectors to the bezel.
To remove a 10.4 or 11.3 inch bezel/display:
1. Disconnect the power from the 6180 Computer.
2. Disconnect all communication and power cables.
3. Remove the clips or mounting stud nuts that secure the computer
to the panel.
Important: There is metal tab that temporarily locks the bottom
of the chassis in the panel during mounting. This tab must be
bent in before bezel / chassis can be removed.
Ï
Ï
Bezel
Gasket
Locking Tab
Panel
4. Remove the computer from the panel or enclosure.
Replacing the
10.4, 11.3 Inch Displays
or Bezel with No Display
The procedures for replacing 11.3 and 10.4 inch bezel/displays are
the same. For purposes of illustration we show the 11.3 inch display.
If you are installing a bezel with no display, the procedures are the
same except for the number of electrical connectors to the bezel.
To remove a 10.4 or 11.3 inch bezel/display:
1. Disconnect the power from the 6180 Computer.
2. Disconnect all communication and power cables.
3. Remove the clips or mounting stud nuts that secure the computer
to the panel.
Important: There is metal tab that temporarily locks the bottom
of the chassis in the panel during mounting. This tab must be
bent in before bezel / chassis can be removed.
Ï
Ï
Bezel
Gasket
Locking Tab
Panel
4. Remove the computer from the panel or enclosure.
Replacing the
10.4, 11.3 Inch Displays
or Bezel with No Display
5
6
7
8
advertisement
Key Features
- 10.4 and 11.3 inch displays
- Touchscreen options
- Replaceable backlight (10.4 inch)
- Industrial grade durability
- Easy installation
Related manuals
Frequently Answers and Questions
How do I replace the backlight in a 10.4 inch RAC6180 display?
Disconnect power, remove the chassis, unplug the backlight power supply cable, remove the old backlight, install the new one, reconnect the power supply cable, and reassemble the chassis.
Can I replace the backlight on the 11.3 inch display?
No, the 11.3 inch display has an integral backlight that cannot be replaced separately. You would need to replace the entire bezel/display assembly.
What precautions should I take when installing the RAC6180 display?
Disconnect all power before working on the display, avoid touching electronic components to prevent electrostatic discharge (ESD), and be cautious when removing and reinstalling the chassis to avoid damage to cables and connectors.
advertisement