KBS Wärmeschrank Owner's Manual
kbs Wärmeschrank is a heated cabinet designed for professional use. It features a stainless steel construction, adjustable temperature control, and a fan for even heat distribution. Ideal for keeping dishes hot, it offers safe and efficient operation with a safety switch and proper earthing.
advertisement
BEDIENUNGSANLEITUNG
KBS Gastrotechnik GmbH – Schoßbergstraße 26 – 65201 Wiesbaden
www.kbs-gastrotechnik.de
Stand September 2024
*Für Druckfehler keine Haftung
KBS Gastrotechnik GmbH – Schoßbergstraße 26 – 65201 Wiesbaden
www.kbs-gastrotechnik.de
Stand September 2024
*Für Druckfehler keine Haftung
2
INTRODUCTION
Dear customer, we thank you for choosing our heated cabinet, we
hope you will be satisfied with the product.
1 WARNINGS
The following instruction manual is an integral part of the equipment
and must be kept at the disposal of operators for any possible advice,
up to the end of the product's life cycle.
Before carrying out any operation, carefully read the information in
the manual regarding safety, installation, use and maintenance.
The equipment must be used only for the use for which it was
designed and only by qualified personnel trained to use the product.
Installation, maintenance and repairs must be carried out exclusively
by an authorized service center or by professionally qualified
personnel, in compliance with the regulations in force and according
to the instructions provided by the manufacturer.
An earth connection is mandatory according to the safety regulations
of the electrical system.
Use the heated cabinet with an ambient temperature between + 5∞C
and +35 ∞C
The entire structure of the heated cabinet is made of 18/10 stainless
steel.
The assembly takes place by electrostatic spot welding and the
internal parts are folded with an anti-cut profile.
The plug to be connected to the power cable must be compliant with
the regulations in force.
Do not block the openings, the heat ventilation and exhaust slits.
This appliance is intended for professional use and complies with the
EC directives in force. The appliance is used to keep dishes hot,
therefore any other use is improper.
The Manufacturer refuses all responsibility for direct and indirect
damage caused by improper installation, tampering with, inadequate
maintenance, improper use and failure to comply with the
regulations contained in the instruction manual.
2 INSTALLATION
2.1 ELECTRICAL CONNECTION
The electrical connection, single phase 220 – 230 V ~ 50/60 Hz, must
be carried out by qualified personnel in compliance with the
European regulations in force.
The heated cabinet is supplied with electric cable but no plug. If a
plug is applied, it must be compatible with the maximum power of
the heated cabinet. It is recommended to have the installation done
by a qualified electrician, in compliance with the regulations in force.
Attention!!! – A bipolar safety switch must be set upstream of the
heated cabinet.
Attention!!! – The equipment must be earthed properly according
to the safety regulations of the electrical system.
2.2 OPERATION
Once the heated cabinet has been installed, set the red switch to
position I and adjust the desired temperature by rotating the special
adjustment knob. The red light indicates that the cabinet is on, the
green light off indicates that the set temperature, which will cause
the green light to go out, has not been reached yet.
Attention!!! – Before switching of the heated cabinet must be
removed the protective film used to protect the table.
INTRODUCTION
Dear customer, we thank you for choosing our heated cabinet, we
hope you will be satisfied with the product.
1 WARNINGS
The following instruction manual is an integral part of the equipment
and must be kept at the disposal of operators for any possible advice,
up to the end of the product's life cycle.
Before carrying out any operation, carefully read the information in
the manual regarding safety, installation, use and maintenance.
The equipment must be used only for the use for which it was
designed and only by qualified personnel trained to use the product.
Installation, maintenance and repairs must be carried out exclusively
by an authorized service center or by professionally qualified
personnel, in compliance with the regulations in force and according
to the instructions provided by the manufacturer.
An earth connection is mandatory according to the safety regulations
of the electrical system.
Use the heated cabinet with an ambient temperature between + 5∞C
and +35 ∞C
The entire structure of the heated cabinet is made of 18/10 stainless
steel.
The assembly takes place by electrostatic spot welding and the
internal parts are folded with an anti-cut profile.
The plug to be connected to the power cable must be compliant with
the regulations in force.
Do not block the openings, the heat ventilation and exhaust slits.
This appliance is intended for professional use and complies with the
EC directives in force. The appliance is used to keep dishes hot,
therefore any other use is improper.
The Manufacturer refuses all responsibility for direct and indirect
damage caused by improper installation, tampering with, inadequate
maintenance, improper use and failure to comply with the
regulations contained in the instruction manual.
2 INSTALLATION
2.1 ELECTRICAL CONNECTION
The electrical connection, single phase 220 – 230 V ~ 50/60 Hz, must
be carried out by qualified personnel in compliance with the
European regulations in force.
The heated cabinet is supplied with electric cable but no plug. If a
plug is applied, it must be compatible with the maximum power of
the heated cabinet. It is recommended to have the installation done
by a qualified electrician, in compliance with the regulations in force.
Attention!!! – A bipolar safety switch must be set upstream of the
heated cabinet.
Attention!!! – The equipment must be earthed properly according
to the safety regulations of the electrical system.
2.2 OPERATION
Once the heated cabinet has been installed, set the red switch to
position I and adjust the desired temperature by rotating the special
adjustment knob. The red light indicates that the cabinet is on, the
green light off indicates that the set temperature, which will cause
the green light to go out, has not been reached yet.
Attention!!! – Before switching of the heated cabinet must be
removed the protective film used to protect the table.
3
3 MAINTENANCE
Attention!!! – Before carrying out any maintenance operations, turn
off the current by using the appropriate switch or disconnecting the
plug.
Attention!!! – Any maintenance operation must be carried out by
qualified personnel only.
Attention!!! – When removing the panels, handle them with great
attention by using gloves to protect hands from possible cuts.
3.1 DISASSEMBLING THE HEATING UNIT
To disassemble the heating unit, remove the internal top first and
then the heating unit located on the right, by unscrewing the six
fixing screws.
3.2 DISASSEMBLING THE ADJUS TMENT UNIT
The adjustment unit can be disassembled by removing the screws
that lock it; after doing so, it will be possible to access the switch, the
lights and the thermostat.
3.3 SPARE PARTS
It is possible to use original or authorized spare parts only. Do not
repair or replace any components that have not been recommended
by this manual. All the other interventions must be carried out by
authorized technical personnel. To ask for a spare part, indicate the
heated table model specified on the label.
The spare parts that can be supplied are the following:
• Fan
• Electrical resistance
• ON/OFF switch
• Thermostat
• Light green
• Light red
• Knob
Carry out the electrical connection according to the diagram given in
figure 1.
4 CLEANING
Attention!!! - Never use detergents containing: sand or caustic soda,
acids or chlorides that affect the surface.
Attention!!! - Any cleaning operation must be carried out with the
hood disconnected from the mains
The cabinet table must be cleaned using a damp cloth with non-
abrasive detergent and drying the surfaces using a dry cloth.
3 MAINTENANCE
Attention!!! – Before carrying out any maintenance operations, turn
off the current by using the appropriate switch or disconnecting the
plug.
Attention!!! – Any maintenance operation must be carried out by
qualified personnel only.
Attention!!! – When removing the panels, handle them with great
attention by using gloves to protect hands from possible cuts.
3.1 DISASSEMBLING THE HEATING UNIT
To disassemble the heating unit, remove the internal top first and
then the heating unit located on the right, by unscrewing the six
fixing screws.
3.2 DISASSEMBLING THE ADJUS TMENT UNIT
The adjustment unit can be disassembled by removing the screws
that lock it; after doing so, it will be possible to access the switch, the
lights and the thermostat.
3.3 SPARE PARTS
It is possible to use original or authorized spare parts only. Do not
repair or replace any components that have not been recommended
by this manual. All the other interventions must be carried out by
authorized technical personnel. To ask for a spare part, indicate the
heated table model specified on the label.
The spare parts that can be supplied are the following:
• Fan
• Electrical resistance
• ON/OFF switch
• Thermostat
• Light green
• Light red
• Knob
Carry out the electrical connection according to the diagram given in
figure 1.
4 CLEANING
Attention!!! - Never use detergents containing: sand or caustic soda,
acids or chlorides that affect the surface.
Attention!!! - Any cleaning operation must be carried out with the
hood disconnected from the mains
The cabinet table must be cleaned using a damp cloth with non-
abrasive detergent and drying the surfaces using a dry cloth.
4
Fig. 1
Fig. 1
5
6
7
8
advertisement
Key Features
- Stainless Steel Construction
- Adjustable Temperature Control
- Fan for Even Heat Distribution
- Safety Switch
- Proper Earthing
- Professional Use
- Hot Dish Keeping
Related manuals
Frequently Answers and Questions
What is the recommended ambient temperature for using the kbs Wärmeschrank?
The recommended ambient temperature for using the kbs Wärmeschrank is between +5°C and +35°C, as stated in the manual.
How do I adjust the temperature of the kbs Wärmeschrank?
After installing the kbs Wärmeschrank, turn the red switch to position I and rotate the special adjustment knob to set the desired temperature.
What type of cleaning products should I use for the kbs Wärmeschrank?
Avoid detergents containing sand, caustic soda, acids, or chlorides that could affect the surface. Use a damp cloth with non-abrasive detergent and dry with a dry cloth.
advertisement