PDF Download
Document
VDO CYTEC C 10 Installation and Operation Manual | Manualzz

Advertisement

Advertisement

English page 1-20
Deutsch Seite 21-40

Français page 41-60

Italiano pagine 61-80

Español pagina 81-100

Nederlands pagina 101-120

GB

C15

D

C15

F

C15

I

C15

E

C15

NL

C15
ETRTO WS in mm KMH WS in inch MPH
47-305 16x1,75 1272 50,1

47-406 20x1,75 1590 62,6

34-540 24x1 3/8 1948 76,7

47-507 24x1,75 1907 75,1

23-571 26x1 1973 77,7

40-559 26x1,5 2026 79,8

44-559 26x1,6 2051 80,7

47-559 26x1,75 2070 81,5

50-559 26x1,9 2089 82,2

54-559 26x2,00 2114 83,2

57-559 26x2,125 2133 84,0

37-590 26x1 3/8 2105 82,9

20-571 26x3/4 1954 76,9

32-630 27x1 1/4 2199 86,6

40-622 28x1,5 2224 87,6

47-622 28x1,75 2268 89,3

40-635 28x1 1/2 2265 89,2

37-622 28x1 3/8 2205 86,8

18-622 700x18C 2102 82,8

20-622 700x20C 2114 83,2

23-622 700x23C 2133 84,0

25-622 700x25C 2146 84,5

28-622 700x28C 2149 84,6

32-622 700x32C 2174 85,6

37-622 700x37C 2205 86,8

40-622 700x40C 2224 87,6

ETRTO WS in mm KMH WS in inch MPH
screw
GB

C

15

1

INSTALLATION AND OPERATION MANUAL - VDO CYTEC C 15

Preface

Thank you for buying a VDO CYTEC bicycle computer. The more familiar you get with this model, the more enjoyable your trips

are going to be.

Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make
you fully benefit from all the technical features of your VDO CYTEC bicycle computer.

We wish you enjoyable trips and rides on your bike with VDO CYTEC

CYCLE PARTS GMBH

Mounting the system

1. Mounting the handlebar holder

The handlebar holder fits handlebars of any diameter. Before mounting the system, decide if you will be using your left or right hand
to operate the computer and then mount the handlebar holder on the respective side. Position the handlebar holder, insert the strap
and adjust it by tightening the screw.

Warning: Before tightening the handlebar holder, make sure to adjust the position of the computer head (inclination) when the LCD-
display is best visible for you. Only when you find the best position tighten the screw.
GB
C

15

2

2. Mounting the speed transmitter

The sensor should be mounted on the

same side of the fork as the holder is

on the handlebar.

Watch out: Do not tighten the cable

ties yet! Accurately position the spoke

magnet and the sensor first, then

tighten the cable ties.

3. Mounting the spoke magnet

Distance between magnet and
sensor should be approx. 1-5 mm.
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22

Advertisement

ALP:
Preparing document for printing…
0%